Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “transient analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

A Stability Analysis for a Hydrodynamic Three-Wave Journal Bearing

The influence of the wave amplitude and oil supply pressure on the dynamic behavior of a hydrodynamic three-wave journal bearing is presented. Both, a transient and a small perturbation technique, were used to predict the threshold to fractional frequency whirl (FFW). In addition, the behavior of the rotor after FFW appeared was determined from the transient analysis. The turbulent effects were also included in the computations. Bearings having a diameter of 30 mm, a length of 27.5 mm, and a clearance of 35 microns were analyzed. Numerical results were compared to experimental results obtained at the NASA GRC. Numerical and experimental results showed that the above-mentioned wave bearing with a wave amplitude ratio of 0.305 operates stably at rotational speeds up to 60,000 rpm, regardless of the oil supply pressure. For smaller wave amplitude ratios, a threshold of stability was found. It was observed that the threshold of stability for lower wave amplitude strongly depends on the oil supply pressure and on the wave amplitude. When the FFW occurs, the journal center maintains its trajectory inside the bearing clearance and therefore the rotor can be run safely without damaging the bearing surfaces.

Ene, Nicoleta M.↗
NASA NTRS1981

Experience on the use of MOSTAB-HFW computer code for horizontal-axis wind turbines

Three topics are covered dealing with the frequencies of a rotating beam, the use of the fundamental mode of a uniform cantilever beam, and the analysis of resonance dwell. Immensely high peak loads were generated by the code for resonance dwell indicating further need for including structural damping and for transient analysis capability. The effect of structural damping, newly incorporated in the code, is described.

Yu, Y. Y.↗
NASA NTRS1982

Structural Analysis of Shells

Structural Analysis of General Shells computer program STAGSC-1 analyzes thin shell branches or segments connected to one another along their boundaries. Program includes stress buckling, vibration and transient analysis of multisegment shells.

Almroth, B. O.↗
NASA NTRS1987

Analysis of internal flows relative to the space shuttle main engine

Cooperative efforts between the Lockheed-Huntsville Computational Mechanics Group and the NASA-MSFC Computational Fluid Dynamics staff has resulted in improved capabilities for numerically simulating incompressible flows generic to the Space Shuttle Main Engine (SSME). A well established and documented CFD code was obtained, modified, and applied to laminar and turbulent flows of the type occurring in the SSME Hot Gas Manifold. The INS3D code was installed on the NASA-MSFC CRAY-XMP computer system and is currently being used by NASA engineers. Studies to perform a transient analysis of the FPB were conducted. The COBRA/TRAC code is recommended for simulating the transient flow of oxygen into the LOX manifold. Property data for modifying the code to represent LOX/GOX flow was collected. The ALFA code was developed and recommended for representing the transient combustion in the preburner. These two codes will couple through the transient boundary conditions to simulate the startup and/or shutdown of the fuel preburner. A study, NAS8-37461, is currently being conducted to implement this modeling effort.

Source record↗
NASA NTRS1979

A generalized modal shock spectra method for spacecraft loads analysis

Unlike the traditional shock spectra approach, the generalization presented in this paper permits elastic interaction between the spacecraft and launch vehicle in order to obtain accurate bounds on the spacecraft response and structural loads. In addition, the modal response from a previous launch vehicle transient analysis - with or without a dummy spacecraft - is exploited in order to define a modal impulse as a simple idealization of the actual forcing function. The idealized modal forcing function is then used to derive explicit expressions for an estimate of the bound on the spacecraft structural response and forces.

Trubert, M.↗
NASA NTRS1991

Parallel Methods on Large-Scale Structural Analysis and Physics Applications; Symposium, Hampton, VA, Feb. 5, 6, 1991, Selected Papers

Recent advances in parallel methods and algorithms integrated into large-scale codes are presented. Consideration is given to problem decomposition (substructuring), efficient matrix solution algorithms for shared memory architectures, dynamic and transient analysis algorithms for shared memory architectures, and algorithms for distributed and massively parallel architectures. Particular attention is given to partitioning of unstructured problems for parallel processing, parallel-vector computation for linear-structural analysis and nonlinear unconstraint optimization problems, a parallel-vector equation solver for unsymmetric matrices on supercomputers, parallel nonlinear finite element dynamic response, multigrid algorithms for solving structural mechanics problems on supercomputers, structural analysis on massively parallel computers, explicit finite element methods with contact-impact on SIMD computers, and the impact of mapping and sparsity on parallelized finite element method modules.

Storaasli, Olaf O.↗
NASA NTRS1975

Analysis of nonlinear structures via mode synthesis

An effective procedure for NASTRAN was developed that permits any number of substructures of any size to be synthesized for the purpose of developing normal modes of vibration of the complete structural system. The technique is extended to permit modal transient analysis of the subdivided system. This latter procedure permits the use of NASTRAN's ability to include nonlinear forces in the problem. The five-phase process is accomplished using standard NASTRAN rigid formats with problem-independent alter packages and DMAP sequences.

Gieseke, R. K.↗
NASA NTRS2010

Analysis of the STS-126 Flow Control Valve Structural-Acoustic Coupling Failure

During the Space Transportation System mission STS-126, one of the main engine's flow control valves incurred an unexpected failure. A section of the valve broke off during liftoff. It is theorized that an acoustic mode of the flowing fuel, coupled with a structural mode of the valve, causing a high cycle fatigue failure. This report documents the analysis efforts conducted in an attempt to verify this theory. Hand calculations, computational fluid dynamics, and finite element methods are all implemented and analyses are performed using steady-state methods in addition to transient analysis methods. The conclusion of the analyses is that there is a critical acoustic mode that aligns with a structural mode of the valve

Jones, Trevor M.↗
NASA NTRS1976

Evaluation of a cost-effective loads approach

A shock spectra/impedance method for loads prediction is used to estimate member loads for the Viking Orbiter, a 7800-lb interplanetary spacecraft that has been designed using transient loads analysis techniques. The transient loads analysis approach leads to a lightweight structure but requires complex and costly analyses. To reduce complexity and cost a shock spectra/impedance method is currently being used to design the Mariner Jupiter Saturn spacecraft. This method has the advantage of using low-cost in-house loads analysis techniques and typically results in more conservative structural loads. The method is evaluated by comparing the increase in Viking member loads to the loads obtained by the transient loads analysis approach. An estimate of the weight penalty incurred by using this method is presented. The paper also compares the calculated flight loads from the transient loads analyses and the shock spectra/impedance method to measured flight data.

Garba, J. A.↗
NASA NTRS1976

Evaluation of a cost-effective loads approach

A shock spectra/impedance method for loads predictions is used to estimate member loads for the Viking Orbiter, a 7800-lb interplanetary spacecraft that has been designed using transient loads analysis techniques. The transient loads analysis approach leads to a lightweight structure but requires complex and costly analyses. To reduce complexity and cost, a shock spectra/impedance method is currently being used to design the Mariner Jupiter Saturn spacecraft. This method has the advantage of using low-cost in-house loads analysis techniques and typically results in more conservative structural loads. The method is evaluated by comparing the increase in Viking member loads to the loads obtained by the transient loads analysis approach. An estimate of the weight penalty incurred by using this method is presented. The paper also compares the calculated flight loads from the transient loads analyses and the shock spectra/impedance method to measured flight data.

Garba, J. A.↗
NASA NTRS1978

On the append and continue features in NASTRAN

The APPEND feature is described which is applicable in the case of real eigenvalue analysis. This feature permitted the addition of new eigenvalues and eigenvectors to those already computed in a previously checkpointed run without re-executing the entire problem. The next feature was the CONTINUE feature which was applicable in the case of transient analysis of coupled equations. This feature enabled the integration of coupled equations to be continued beyond the last output time for which the solution was obtained in a previously checkpointed run (without re-executing the entire problem). These two features are illustrated by suitable examples.

Pamidi, P. R.↗
NASA NTRS1975

Nonlinear seismic analysis of a reactor structure impact between core components

The seismic analysis of the FFTF-PIOTA (Fast Flux Test Facility-Postirradiation Open Test Assembly), subjected to a horizontal DBE (Design Base Earthquake) is presented. The PIOTA is the first in a set of open test assemblies to be designed for the FFTF. Employing the direct method of transient analysis, the governing differential equations describing the motion of the system are set up directly and are implicitly integrated numerically in time. A simple lumped-nass beam model of the FFTF which includes small clearances between core components is used as a "driver" for a fine mesh model of the PIOTA. The nonlinear forces due to the impact of the core components and their effect on the PIOTA are computed.

Hill, R. G.↗
NASA NTRS1983

Generalized modal shock spectra within indeterminate interface

It is noted that the generalized modal shock spectra method had limitations on the degree of structural static determinacy of the spacecraft-to-launch-vehicle interface. The 'interface modes' is used here to remove these practical limitations. The governing differential equations are derived and then shown to be valid either for integrating the modal models of two or more substructures that have been previously obtained separately or for removing a substructure from a previously available system modal model. Emphasis is placed on the integration problems in the context of the generalized modal shock spectra approach. A minimum of information the modal response of a previously obtained transient analysis of the unloaded launch vehicle is exploited in order to define an idealized modal impulse function and derive approximate explicit expressions for an estimate of the bounds of the spacecraft response. In addition, a numerical model is solved in order to compare the present results with the transient solution.

Salama, M.↗
NASA NTRS1988

Dynamic analysis of nonlinear rotor-housing systems

Nonlinear analysis methods are developed which will enable the reliable prediction of the dynamic behavior of the space shuttle main engine (SSME) turbopumps in the presence of bearing clearances and other local nonlinearities. A computationally efficient convolution method, based on discretized Duhamel and transition matrix integral formulations, is developed for the transient analysis. In the formulation, the coupling forces due to the nonlinearities are treated as external forces acting on the coupled subsystems. Iteration is utilized to determine their magnitudes at each time increment. The method is applied to a nonlinear generic model of the high pressure oxygen turbopump (HPOTP). As compared to the fourth order Runge-Kutta numerical integration methods, the convolution approach proved to be more accurate and more highly efficient. For determining the nonlinear, steady-state periodic responses, an incremental harmonic balance method was also developed. The method was successfully used to determine dominantly harmonic and subharmonic responses fo the HPOTP generic model with bearing clearances. A reduction method similar to the impedance formulation utilized with linear systems is used to reduce the housing-rotor models to their coordinates at the bearing clearances. Recommendations are included for further development of the method, for extending the analysis to aperiodic and chaotic regimes and for conducting critical parameteric studies of the nonlinear response of the current SSME turbopumps.

Noah, Sherif T.↗
NASA NTRS1990

On the numerical solution of the dynamically loaded hydrodynamic lubrication of the point contact problem

The transient analysis of hydrodynamic lubrication of a point-contact is presented. A body-fitted coordinate system is introduced to transform the physical domain to a rectangular computational domain, enabling the use of the Newton-Raphson method for determining pressures and locating the cavitation boundary, where the Reynolds boundary condition is specified. In order to obtain the transient solution, an explicit Euler method is used to effect a time march. The transient dynamic load is a sinusoidal function of time with frequency, fractional loading, and mean load as parameters. Results include the variation of the minimum film thickness and phase-lag with time as functions of excitation frequency. The results are compared with the analytic solution to the transient step bearing problem with the same dynamic loading function. The similarities of the results suggest an approximate model of the point contact minimum film thickness solution.

Lim, Sang G.↗
NASA NTRS1987

Checkpoint and restart procedures for single and multi-stage structural model analysis in NASTRAN/COSMIC on a CDC 176

The Underwater Explosions Research Division (UERD) of the David Taylor Naval Ship Research and Development Center makes extensive use of NASTRAN/COSMIC on a CDC 176 to evaluate the structural response of ship structures subjected to underwater explosion shock loadings in the time domain. As relatively new users, UERD engineers have experienced difficulties with the checkpoint/restart feature because of the vague instructions in the user manual. Working procedures for the application of the checkpoint/restart feature to the transient analysis using NASTRAN/COSMIC are illustrated.

Camp, George H.↗
NASA NTRS1992

Integrated numerical methods for hypersonic aircraft cooling systems analysis

Numerical methods have been developed for the analysis of hypersonic aircraft cooling systems. A general purpose finite difference thermal analysis code is used to determine areas which must be cooled. Complex cooling networks of series and parallel flow can be analyzed using a finite difference computer program. Both internal fluid flow and heat transfer are analyzed, because increased heat flow causes a decrease in the flow of the coolant. The steady state solution is a successive point iterative method. The transient analysis uses implicit forward-backward differencing. Several examples of the use of the program in studies of hypersonic aircraft and rockets are provided.

Petley, Dennis H.↗