Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “clamp”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 271 records · Page 15
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Buckling of eccentrically stringer-stiffened cylindrical panels under axial compression

The paper presents numerical results, based on Donnell shell theory, for the axial compressive buckling loads for eccentrically stringer-stiffened circular cylindrical panels, in a study of the effect of boundary conditions and panel width on the buckling load. The two cases of inside and outside stiffeners were considered. The complete cylinder buckling load was reached only for panels under classical simply supported boundary conditions. The prevention of circumferential displacement is found to be the most important in-plane boundary condition from the point of view of increasing the buckling load. Clamping is found more effective in increasing the buckling loads of panels with free circumferential edge displacement than of panels with zero edge displacement. When panel width is equal to or greater than 180 deg, the panel buckling loads are within 10% of the complete cylinder load for all cases except one simply supported panel with outside stringers. Buckling loads were higher for outside stringers, except for very narrow panels that are restrained against circumferential edge displacement. Eccentricity effects are generally similar for clamped and simply supported panels with the same in-plane boundary conditions.

Sobel, L. H.↗
NASA NTRS1976

Aeroelastic stability and control of an oblique wing - Wind tunnel experiments

Results are presented for wind tunnel tests of an elastic wing model to verify the theoretical predictions for the aeroelastic instability of an oblique wing. The model wing has an elliptic planform of 10 to 1 axis ratio and a symmetrical airfoil section of 7-1/2% thickness/chord ratio. The wing is of wood and as may be seen in the photographs presented, slack wires are used to limit the amplitude of unstable motions. The fuselage is mounted on bearings permitting freedom of roll, but provision is made to clamp the fuselage for some of the tests. It is found that freedom in roll increases the dynamic pressure at which aeroelastic instability first appears. With the model free in roll, the effectiveness of the ailerons in maintaining trim is not noticeably affected by passage through the speed at which the wing would become unstable if clamped.

Jones, R. T.↗
NASA NTRS1976

Aeroelastic stability and control of an oblique wing

Dynamic model tests were staged to compare the aeroelastic stability of a free-flying oblique-winged aircraft and the known divergent instability characterizing swept-forward wing configurations, to test the effect of wing elasticity on aileron control and trim. The aircraft fuselage was clamped in some tests and left free to roll in others. Two rigid wing panels were hinged near the wing center with elastic restraining springs. It is found that the aeroelastic divergence affecting swept-forward wings does not occur with an oblique wing, whose aeroelastic instability sets in at a dynamic pressure exceeding that for static divergence of swept-forward wings, and appears in the form of undamped oscillations. Oblique wing stability is sensitive to the moment of inertia of the fuselage in roll. Roll control and lateral trim are attainable with conventional ailerons, even at speeds at which divergence of a clamped forward wing shows up.

Jones, R. T.↗
NASA NTRS1979

Attaching strain transducers to fragile materials

A-shaped clamp prevents damage to thin, brittle specimens and supports displacement transducer away from heated zone. Also it defines reference points for strain measurement on specimen surface thus preventing specimen cracking due to unequal thermal expansion between clamp and holder.

Duggan, M. F.↗
NASA NTRS1979

Fixture for limited-access welding

Fixture consisting of screw-on expansion clamps and backup bar aligns edges of plates for precision butt welding. Tool holds plates securely, without offset, and allows welding and clamp disassembly to be completed when there is access from only one side of structure.

Tryon, J. R.↗
NASA NTRS1980

Adjusting an electron beam for drilling

Reticle contains two concentric circles: inner circle insures beam circularity and outer circle is guide to prevent beam from cutting workpiece clamp. Precise measurement of beam and clamp are required with old reticle. New reticle speeds up electron-beam drilling process by eliminating need to rotate eyepiece to make measurements against reticle scale.

Childress, C. L.↗
NASA NTRS1979

Summary of the two year NASA program for active control of ATS-5/6 environmental charging

Experiments conducted on the ATS 5 and ATS 6 which have demonstrated the feasibility of modifying or clamping the environmentally induced potential of these spacecraft are described. The results of these experiments indicate that a thermionic electron source is capable of replacing photo-emitted electrons during eclipse. However, the utility of this type of device is limited if its emission is suppressed by local electric fields. On the other hand, it is shown that a plasma source will not only serve as a substitute for photo-emitted electrons but will also suppress differential charging of isolated elements of the spacecraft which would tend to suppress electron emission. This later device is therefore capable of clamping the potential of a spacecraft without special considerations of its coupling to the ambient plasma.

Bartlett, R. O.↗
NASA NTRS1980

Vise holds specimens for microscope

Convenient, miniature, spring-loaded clamp holds specimens for scanning electron microscope. Clamp is made out of nesting sections of studded angle-aluminum. Specimens are easier to mount and dismount with vise than with conductive adhesive or paint.

Greule, W. N.↗
NASA NTRS1980

Drill-motor holding fixture

Guide improves accuracy and reduces likelihood of bit breakage in drilling large work pieces. Drill motor is mounted on pipe that slides on furniture clamp. Drill is driven into work piece by turning furniture-clamp handle.

Chartier, E. N.↗
NASA NTRS1980

Knife-edge seal for vacuum bagging

Cam actuated clamps pinch bagging material between long knife edge (mounted to clamps) and high temperature rubber cushion bonded to baseplate. No adhesive, tape, or sealing groove is needed to seal edge of bagging sheet against base plate.

Rauschl, J. A.↗
NASA NTRS1981

Cooling/grounding mount for hybrid circuits

Extremely short input and output connections, adequate grounding, and efficient heat removal for hybrid integrated circuits are possible with mounting. Rectangular clamp holds hybrid on printed-circuit board, in contact with heat-conductive ground plate. Clamp is attached to ground plane by bolts.

Bagstad, B.↗
NASA NTRS1981

Soft container for explosive nuts

Flexible fabric fits over variety of assembly shapes to contain debris produced by detonations or safety tests. Bag material is woven multifilament polyamide or aramid. Belt loops hold bag to clamp. Ring supports explosive nut structure and detonator wires, and after nut is mounted, bag and clamp are slipped over ring and fastened.

Glenn, D. C.↗
NASA NTRS1979

Buckling of rotating beams

The stability of a beam subjected to compressive centrifugal forces arising from steady rotation about an axis which does not pass through the clamped end of the beam is analyzed to determine the critical rotational speeds for buckling in the inplane and out-of-plane directions. The differential equations of motion are solved numerically using an integrating matrix method in combination with an eigenanalysis to determine the eigenvalues from which stability is assessed. The results clarify several differences which have been identified in the literature relating to the proper behavior of the critical rotational speed for buckling as the radius of rotation of the clamped end of the beam is reduced.

White, W. F., Jr.↗
NASA NTRS1981

CCD correlated quadruple sampling processor

A correlated quadruple sampling processor for improved signal-to-noise ratio in the output of a charge-coupled device (CCD) is comprised of: switching means for momentarily clamping a CCD signal line at a first reference level A before a CCD data pulse and then obtaining a first data sample B with respect to the reference A during a CCD data pulse, and storing the positive sample B-A; switching means for momentarily clamping the CCD signal line a second time at the level C during the presence of the CCD data pulse and then obtaining a second data sample D with respect to the reference level C after the CCD data pulse, and storing the negative sample D-C; and means for obtaining the difference between the stored samples +(B-A) and -(D-C), thus increasing the net signal amplitude by a factor of about 2 while the noise would be increased by only a factor of square root of 2 since there will be no correlation in the noise between the double samples +(B-A) and -(D-C) effectively added.

Gaalema, S. D.↗
NASA NTRS1981

Power transistor switching characterization

The switching properties of power transistors are investigated. The devices studied were housed in IO-3 cases and were of an n(+)-p-n(-)-n(+) vertical dopant structure. The effects of the magnitude of the reverse-base current and temperature on the reverse-bias second breakdown characteristics are discussed. Brief discussions of device degradation due to second breakdown and of a constant voltage turn-off circuit are included. A description of a vacuum tube voltage clamp circuit which reduces clamped collector voltage overshoot is given.

Blackburn, D. L.↗
NASA NTRS1980

Buckling of prismatic structures under biaxial loading

A one term analysis is presented for the elastic buckling of prismatic structures with either classical simple support or completely clamped boundary conditions on the transverse ends. Results suggest that a one term solution based on an appropriate choice of coordinate functions may lead to satisfactory buckling loads for other prismatic structures with completely clamped and other end conditions.

Ashour, H. A.↗
NASA NTRS1980

Secondary mirror subassembly in the 2.4 m NASA optical telescope

The secondary mirror is a circular disc provided with a shoulder. Three clamps located 120 deg apart support the mirror shoulder. On one side of the mirror shoulder, a coated graphite-epoxy ring connects the three clamps. Three axial flexures with a low radial compliance extend out from a support platform constructed of coated graphite-epoxy box structs and invar corners, and provide a nominal in-plane zero coefficient of thermal expansion. In each invar corner piece, a ball joint provides a connection to a expansion. In each invar corner piece, a ball joint provides a connection to a six-degree-of-freedom adjustment system that can move the secondary mirror with a high degree of precision in defocus, decenter, and tilt. Thermal controls that maintain structural-element temperature variations within specified limits insure that the assembly exceeds stability and figure control requirements on the secondary mirror.

Ahmed, N.↗