Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optical losses”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Spectrophotovoltaic orbital power generation

A system with 1000 : 1 concentration ratio is defined, using a cassegrain telescope as the first stage concentration (270 x) and compound parabolic concentrators (CPC) for the second stage concentration of 4.7 x for each spectral band. Using reported state of the art (S.O.A.) solar cells device parameters and considering structural losses due to optics and beamsplitters, the efficiencies of one to four cell systems were calculated with efficiencies varying from approximately 22% to 30%. Taking into account cost of the optics, beamsplitter, radiator, and the cost of developing new cells the most cost effective system is the GaAs/Si system.

Knowles, G.↗
NASA NTRS1982

Tunable diode-laser heterodyne spectrometer for remote observations near 8 microns

A diode-laser-based, ultrahigh resolution IR heterodyne spectrometer for laboratory and field use has been developed for operation between 7.5 and 8.5 microns. The local oscillator is a PbSe tunable diode laser kept continuously at operating temperatures of 12-60 K using a closed-cycle cooler. The laser output frequency is controlled and stabilized using a high-precision diode current supply, constant temperature controller, and a shock isolator mounted between the refrigerator cold tip and the diode mount. The system largely employs reflecting optics to minimize losses from internal reflection and absorption and to eliminate chromatic effects. Spectral analysis of the diode-laser output between 0 and 1 GHz reveals excess noise at many diode current settings, which limits the IR spectral regions over which useful heterodyne operation can be achieved. Observations have been made of atmospheric N2O, O3, and CH4 between 1170 and 1200/cm, using both a single-frequency swept IF channel and a 64-channel RF spectral line receiver with a total IF coverage of 1600 MHz.

Glenar, D.↗
NASA NTRS1984

Research in millimeter wave techniques

Work on the development of an improved 183 GHz subharmonic mixer was concentrated in two areas. First, there was an improved performance from current mixer body designs by testing different diodes and varying the whisker lengths. Second, there is the design of a new body structure. The whisker and diode pinsare in the same piece of the mixer that holds the substrate, reducing any motion of the parts that form the ohmic contacts of the diodes circuit. The broadband, low loss, quasi-optical diplexer, which is designed for use with a single ended mixer, has been developed. It uses a Gaussian beam waveguide as its transmission medium. The difference between the diplexer and other diplexers is the use of a Fabry Perot parallel plate filter. One is a multichannel radiometer system. Another approach is a quasi-optical RF polarization diplexer and another receiver. Some of the receivers developed were flown in aircraft and degraded considerably because of an LO failure. A technique for adding a 118 GHz channel to the existing Atmospheric Moisture Microwave Scanner radiometer system, using the RF diplexing scheme, is presented.

Forsythe, R. E.↗
NASA NTRS1986

Why P/OF should look for evidences of over-dense structures in solar flare hard X-ray sources

White-light and hard X-ray (HXR) observations of two white-light flares (WLFs) show that if the radiative losses in the optical continuum are powered by fast electrons directly heating the WLF source, then the column density constraints imposed by the finite range of the electrons requires that the WLF consist of an over-dense region in the chromosphere, with density exceeding 10 to the 14th power/cu cm. Thus, we recommend that P/OF search for evidences of over-dense structures in HXR images obtained simultaneously with optical observations of flares.

Neidig, D. F.↗
NASA NTRS1991

High-Gain AlxGa1-xAs/GaAs Transistors For Neural Networks

High-gain AlxGa1-xAs/GaAs npn double heterojunction bipolar transistors developed for use as phototransistors in optoelectronic integrated circuits, especially in artificial neural networks. Transistors perform both photodetection and saturating-amplification functions of neurons. Good candidates for such application because structurally compatible with laser diodes and light-emitting diodes, detect light, and provide high current gain needed to compensate for losses in holographic optical elements.

Kim, Jae-Hoon↗
NASA NTRS1991

Non-Maxwellian electron distributions in models of the solar atmosphere

In this paper, the solar models of Fontenla et al. (1990) are extended to coronal temperatures using optically thin radiative losses and a semicircular loop geometry. The effects of a non-Maxwellian high-energy tail of the electron distribution function is tested by performing a Fokker-Planck calculation of the tail. The results show that the downward conductive heat flux is very clsoe to that given by Braginskii (1965) for small departures from a Maxwellian distribution. The effects of the high-energy tail of the electron distribution on element ionization are computed and found to be negligible for all ionization states of O, Ne, and Si. It is concluded that, for quiet sun loop models in stationary energy balance, the ionization state of all elements is not significantly affected by the non-Maxwellian tail of the electron velocity distribution, and that the heat flux can be computed by considering only small first-order departures from the Maxwellian distribution.

Macneice, P.↗
NASA NTRS1992

Quasi-elastic nuclear scattering at high energies

The quasi-elastic scattering of two nuclei is considered in the high-energy optical model. Energy loss and momentum transfer spectra for projectile ions are evaluated in terms of an inelastic multiple-scattering series corresponding to multiple knockout of target nucleons. The leading-order correction to the coherent projectile approximation is evaluated. Calculations are compared with experiments.

Cucinotta, Francis A.↗
NASA NTRS1996

A Secure Key Distribution System of Quantum Cryptography Based on the Coherent State

The cryptographic communication has a lot of important applications, particularly in the magnificent prospects of private communication. As one knows, the security of cryptographic channel depends crucially on the secrecy of the key. The Vernam cipher is the only cipher system which has guaranteed security. In that system the key must be as long as the message and most be used only once. Quantum cryptography is a method whereby key secrecy can be guaranteed by a physical law. So it is impossible, even in principle, to eavesdrop on such channels. Quantum cryptography has been developed in recent years. Up to now, many schemes of quantum cryptography have been proposed. Now one of the main problems in this field is how to increase transmission distance. In order to use quantum nature of light, up to now proposed schemes all use very dim light pulses. The average photon number is about 0.1. Because of the loss of the optical fiber, it is difficult for the quantum cryptography based on one photon level or on dim light to realize quantum key-distribution over long distance. A quantum key distribution based on coherent state is introduced in this paper. Here we discuss the feasibility and security of this scheme.

Guo, Guang-Can↗
NASA NTRS1998

A Fiber-Optic Coupled Telescope for Water Vapor DIAL Receivers

A fiber-optic coupled telescope of low complexity was constructed and tested. The major loss mechanisms of the optical system have been characterized. Light collected by the receiver mirror is focused onto an optical fiber, and the output of the fiber is filtered by an interference filter and then focused onto an APD detector. This system was used in lidar field measurements with a 532-nm Nd:YAG laser beam. The results were encouraging. A numerical model used for calculation of the expected return signal agreed with the lidar return signal obtained. The assembled system was easy to align and operate and weighed about 8 kg for a 30 cm (12") mirror system. This weight is low enough to allow mounting of the fiber-optic telescope receiver system in a UAV. Furthermore, the good agreement between the numerical lidar model and the performance of the actual receiver system, suggests that this model may be used for estimation of the performance of this and other lidar systems in the future. Such telescopes are relatively easy to construct and align. The fiber optic cable allows easy placement of the optical detector in any position. These telescope systems should find widespread use in aircraft and space home DIAL water vapor receiver systems.

DeYoung, Russell J.↗
NASA NTRS1999

High-Efficiency Autonomous Coherent Lidar

A useful measure of sensor performance is the transceiver system efficiency n (sub sys). Which consists of the antenna efficiency n (sub a) and optical and electronic losses. Typically, the lidar equation and the antenna efficiency are defined in terms of the telescope aperture area. However, during the assembly of a coherent transceiver, it is important to measure the system efficiency before the installation of the beamexpanding telescope (i.e., the untruncated-beam system efficiency). Therefore, to accommodate both truncated and untruncated beam efficiency measurements, we define the lidar equation and the antenna efficiency in terms of the beam area rather than the commonly used aperture area referenced definition. With a well-designed Gaussian-beam lidar, aperture area referenced system efficiencies of 15 to 20 % (23-31% relative to the beam area) are readily achievable. In this paper we compare the differences between these efficiency definitions. We then describe techniques by which high efficiency can be achieved, followed by a discussion several novel auto alignment techniques developed to maintain high efficiency.

Philip Gatt↗
NASA NTRS1999

Experimental Cross Sections for Excitation of the 2s S-2 yields 2p P-2 Transition in C(3+)

Experimental cross sections are presented for excitation of the 2s yields 2p transition in C(3+). Use is made of the energy-loss method with merged beams. Also described is use of a multipole "electronic aperture" to discriminate against elastically-scattered electrons. Comparisons are made with previous experimental energy-loss and optical-emission data, and with results of several theoretical calculations.

Chutjian, A.↗
NASA NTRS2012

Results of International Space Station Vehicle Materials Exposed on MISSE-7B

Materials samples were exposed to the low Earth orbit (LEO) environment as part of the MISSE-7B flight experiment for 18 months. Optical properties, thickness/mass loss, surface elemental analysis, visual and microscopic analysis for surface change are some of the techniques employed in this investigation. Where possible, the MISSE-7B results are compared to analyses from other LEO experiments. ISS materials currently flying on MISSE-8 are also discussed.

Finckenor, Miria M.↗
NASA NTRS2013

Further Analysis of Materials Exposed on MISSE-6 and-7B

Materials samples were exposed to the low Earth orbit (LEO) environment as part of the MISSE- 6 and -7B flight experiments. Optical properties, thickness/mass loss, surface elemental analysis, visual and microscopic analysis for surface change are some of the techniques employed in this investigation. Effects of molecular contamination are discussed. Where possible, the MISSE-6 and -7B results are compared to analyses from other LEO experiments.

Finckenor, Miria↗
NASA NTRS1980

Ultrapure glass optical waveguide development in microgravity by the sol-gel process

The alkali-borosilicate system was selected as the glass system for the preparation of ultrapure low loss glasses suitable for optical communication. The effect of different oxide contents on the absorption loss was critically reviewed. One composition was chosen to develop the gel preparation procedure in the alkali-borosilicate system. In addition, several procedures for the preparation of gels based on two different approaches were developed. The influence of different preparation parameters were investigated qualitatively. Several conclusions are drawn from the results.

Mukherjee, S. P.↗
NASA NTRS2026

A Study of Space Environment Effect on Highly Thermally Conductive Hybrid Carbon Fiber Polymer Composites

A set of novel highly thermally conductive hybrid carbon fiber (CF) polymer composites has been developed for lightweight thermal radiator applications in space missions. This study investigates the effects of the space environment on these materials following exposure in low-Earth orbit (LEO) during the Materials International Space Station Experiment (MISSE)-17 flight mission, where samples experienced 159 days of combined atomic oxygen (AO), ultraviolet (UV) radiation, high vacuum, space radiation and thermal cycling. Post-flight characterization included weight loss, surface morphology, thermo-optical properties, molecular structures, glass transition temperature, thermal degradation and thermal conductivity analyses. The pyrolytic graphite sheet (PGS) samples exhibited negligible weight loss, stable thermo-optical property, and only minor oxidation signature on the exposed surface. Although AO erosion of the epoxy polymer matrix was evident, carbon nanotube (CNT)-infused PGS/CF epoxy composites retained high thermal emissivity and preserved their high thermal conductivities. These results demonstrate that the novel highly thermally conductive hybrid CF composites possess strong environmental resilience and are promising candidates for lightweight thermal radiators and thermal management components in future space exploration missions.

Space Environment↗
DOE OSTI2023

Band Bending at CdTe Solar Cell Contacts: Correlating Electro‐Optical and X‐Ray Photoelectron Spectroscopy Analyses of Thin Film Solar Cells

With the semiconductor bulk properties reaching target values for highly efficient solar cells, efforts are applied to reduce losses at solar cell interfaces and contacts. Advances in understanding back contacts in thin‐film polycrystalline CdTe solar cells, a leading thin‐film PV technology, are reported. By using X‐Ray photoelectron spectroscopy, Kelvin probe spectroscopy, time‐ and energy‐resolved photoluminescence, defects at the back contact are analyzed. Densities of recombination centers and charged defects that induce near‐back‐contact band bending, both resulting in recombination losses, were estimated. Electro‐optical and surface analysis results are integrated into a device model, simulating the performance of CdSeTe/CdTe solar cells with 902 mV open circuit voltage.

14 SOLAR ENERGY↗
NASA NTRS2012

Quantum Limits of Space-to-Ground Optical Communications

For a pure loss channel, the ultimate capacity can be achieved with classical coherent states (i.e., ideal laser light): (1) Capacity-achieving receiver (measurement) is yet to be determined. (2) Heterodyne detection approaches the ultimate capacity at high mean photon numbers. (3) Photon-counting approaches the ultimate capacity at low mean photon numbers. A number of current technology limits drive the achievable performance of free-space communication links. Approaching fundamental limits in the bandwidth-limited regime: (1) Heterodyne detection with high-order coherent-state modulation approaches ultimate limits. SOA improvements to laser phase noise, adaptive optics systems for atmospheric transmission would help. (2) High-order intensity modulation and photon-counting can approach heterodyne detection within approximately a factor of 2. This may have advantages over coherent detection in the presence of turbulence. Approaching fundamental limits in the photon-limited regime (1) Low-duty cycle binary coherent-state modulation (OOK, PPM) approaches ultimate limits. SOA improvements to laser extinction ratio, receiver dark noise, jitter, and blocking would help. (2) In some link geometries (near field links) number-state transmission could improve over coherent-state transmission

laser communications↗
DOE OSTI2022

ZnO-Au x Cu 1-x Alloy and ZnO-Au x Al 1-x Alloy Vertically Aligned Nanocomposites for Low-Loss Plasmonic Metamaterials

Hyperbolic metamaterials are a class of materials exhibiting anisotropic dielectric function owing to the morphology of the nanostructures. In these structures, one direction behaves as a metal, and the orthogonal direction behaves as a dielectric material. Applications include subdiffraction imaging and hyperlenses. However, key limiting factors include energy losses of noble metals and challenging fabrication methods. In this work, self-assembled plasmonic metamaterials consisting of anisotropic nanoalloy pillars embedded into the ZnO matrix are developed using a seed-layer approach. Alloys of Au x Al 1-x or Au x Cu 1-x are explored due to their lower losses and higher stability. Optical and microstructural properties were explored. The ZnO-Au x Cu 1-x system demonstrated excellent epitaxial quality and optical properties compared with the ZnO-Au x Al 1-x system. Both nanocomposite systems demonstrate plasmonic resonance, hyperbolic dispersion, low losses, and epsilon-near-zero permittivity, making them promising candidates towards direct photonic integration.

36 MATERIALS SCIENCE↗