SEARCH · Engineering Papers

Results for “material type”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Radiation sensitivity of quartz crystal oscillators experiment for the Long Duration Exposure Facility (LDEF)

Factors determining the radiation sensitivity of quartz crystal oscillators were studied on NASA's LDEF. Quartz materials were examined in the transmission electron microscope (TEM) and classified as to their sensitivity to radiation damage by establishing the rate of damage caused by the electron beam in the microscope. Two types of materials, i.e., swept premium Q quartz and natural quartz were chosen because clear differences were observed in their response to the electron beam in the TEM studies. Quartz resonators were then fabricated from them, tested for frequency stability over a greater than 6 mo. period and flown on the LDEF satellite. After retrieval (more than 7 yrs in space) the stability of the resonators was again determined. All of the space exposed resonators fabricated with swept premium Q material exhibited a frequency shift above that of the control resonators: none of the resonators fabricated from the natural quartz materials exhibited such a shift. The significant differences observed between the two types of materials in both the ground-based TEM studies and the space radiation induced frequency changes suggest that there may be a correlation between the two observations.

Ahearn, J. S.↗

NASA NTRS1975

Lake eutrophication as indicated by ERTS satellite imagery

Light reflectance from water in the laboratory always correlates to the water quality parameter of turbidity. This turbidity is caused by suspended solids in the water and for a particular type of material there is a good correlation between the weight of these suspended solids and turbidity. However, this correlation is different for different types of material. When this suspended material is living green matter as in an eutrophic lake, the changes in reflectance can be detected as changes in brightness on a particular aerial image. Two test sites have shown that there is indeed a good correlation between the brightness on an ERTS image and lake eutrophication.

Scherz, J. P.↗

NASA NTRS1992

Impact damage resistance of composite fuselage structure, part 1

The impact damage resistance of laminated composite transport aircraft fuselage structures was studied experimentally. A statistically based designed experiment was used to examine numerous material, laminate, structural, and extrinsic (e.g., impactor type) variables. The relative importance and quantitative measure of the effect of each variable and variable interactions on responses including impactor dynamic response, visibility, and internal damage state were determined. The study utilized 32 three-stiffener panels, each with a unique combination of material type, material forms, and structural geometry. Two manufacturing techniques, tow placement and tape lamination, were used to build panels representative of potential fuselage crown, keel, and lower side-panel designs. Various combinations of impactor variables representing various foreign-object-impact threats to the aircraft were examined. Impacts performed at different structural locations within each panel (e.g., skin midbay, stiffener attaching flange, etc.) were considered separate parallel experiments. The relationship between input variables, measured damage states, and structural response to this damage are presented including recommendations for materials and impact test methods for fuselage structure.

Dost, E. F.↗

NASA NTRS1981

Susceptibility of materials processing experiments to low-level accelerations

The types of material processing experiments being considered for shuttle can be grouped into four categories: (1) contained solidification experiment; (2) quasicontainerless experiments; (3) containerless experiments; and (4) fluids experiments. Low level steady acceleration, compensated and uncompensated transient accelerations, and rotation induced flow factors that must be considered in the acceleration environment of a space vehicle whose importance depends on the type of experiment being performed. Some control of these factors may be exercised by the location and orientation of the experiment relative to shuttle and by the orbit vehicle attitude chosen for mission. The effects of the various residual accelerations can have serious consequence to the control of the experiment and must be factored into the design and operation of the apparatus.

Naumann, R. J.↗

NASA NTRS1951

Relations between the modulus of elasticity of binary alloys and their structure

A comprehensive survey of the elastic modulus of binary alloys as a function of the concentration is presented. Alloys that form continuous solid solutions, limited solid solutions, eutectic alloys, and alloys with intermetallic phases are investigated. Systems having the most important structures have been examined to obtain criteria for the relation between lattice structure, type of binding, and elastic behavior.

METALS - STRUCTURES↗

NASA NTRS1984

The effect of the space environment on composite materials (A0138-9)

The objective is to test different types of materials (laminates, thermal coatings, and adhesives) to determine their actual useful lifetime. These experiments will also make is possible to integrate the histories of the thermal and mechanical characteristics into models of the composite structures. The experiment is passive and is located in one of the boxes in a 12-in.-deep peripheral tray with nine other experiments from France. The box will provide protection for the samples from contamination during the launch and reentry phases of the Long Duration Exposure Facility mission. The experiment revolves around four themes of study: thermal coatings, adhesives, dimensional stability, and mechanical characteristics. The various materials will be arranged in six levels within the box, so only the first level will be subjected to direct solar radiation. Each level will consist of plates from which test specimens will be cut after the mission.

Parcelier, M.↗

NASA NTRS2007

Conversion of type of quantum well structure

A method for converting a Type 2 quantum well semiconductor material to a Type 1 material. A second layer of undoped material is placed between first and third layers of selectively doped material, which are separated from the second layer by undoped layers having small widths. Doping profiles are chosen so that a first electrical potential increment across a first layer-second layer interface is equal to a first selected value and/or a second electrical potential increment across a second layer-third layer interface is equal to a second selected value. The semiconductor structure thus produced is useful as a laser material and as an incident light detector material in various wavelength regions, such as a mid-infrared region.

Ning, Cun-Zheng↗

NASA NTRS2007

Conversion of Type of Quantum Well Structure

Ning, Cun-Zheng↗

NASA NTRS1978

Materials technology development for long life large space systems

Large Space Systems materials requirements are discussed in terms of types of materials, critical properties, and environmental stability. An outline is given of the materials technology development that will be needed to meet these requirements.

Gause, R. L.↗

NASA NTRS1987

Materials processing in space

Prospects for materials processing in space are addressed. The types of materials that are of the most commercial interest in this regard are examined, and the relevant microgravity facilities and technologies are discussed. The characteristics of the Space Shuttle and the Free Flyer with regard to materials processing in space are briefly considered. The principal manufacturers and consumers of space-processed products are described. The potential impact of these products is assessed.

Kohli, Rajiv↗

NASA NTRS1984

Flat-plate solar array project process development area, process research of non-CZ silicon material

The program is designed to investigate the fabrication of solar cells on N-type base material by a simultaneous diffusion of N-type and P-type dopants to form an P(+)NN(+) structure. The results of simultaneous diffusion experiments are being compared to cells fabricated using sequential diffusion of dopants into N-base material in the same resistivity range. The process used for the fabrication of the simultaneously diffused P(+)NN(+) cells follows the standard Westinghouse baseline sequence for P-base material except that the two diffusion processes (boron and phosphorus) are replaced by a single diffusion step. All experiments are carried out on N-type dendritic web grown in the Westinghouse pre-pilot facility. The resistivities vary from 0.5 (UC OMEGA)cm to 5 (UC OMEGA)cm. The dopant sources used for both the simultaneous and sequential diffusion experiments are commercial metallorganic solutions with phosphorus or boron components. After these liquids are applied to the web surface, they are baked to form a hard glass which acts as a diffusion source at elevated temperatures. In experiments performed thus far, cells produced in sequential diffusion tests have properties essentially equal to the baseline N(+)PP(+) cells. However, the simultaneous diffusions have produced cells with much lower IV characteristics mainly due to cross-doping of the sources at the diffusion temperature. This cross-doping is due to the high vapor pressure phosphorus (applied as a metallorganic to the back surface) diffusion through the SiO2 mask and then acting as a diffusant source for the front surface.

Campbell, R. B.↗

NASA NTRS2001

Synthesis of ZnO:As Films Using Off-Axis Sputtering Deposition

As a novel oxide semiconductor material, ZnO is interesting for use in many applications. For fabricating electronic devices, it is important to have n- and p- type ZnO materials. Arsenic has been proven to be one of the p-type dopants for ZnO materials. However, information in studying the ZnAsO ternary compound films has been scarce. In order to investigate the morphology, structure and electrical properties of ZnAsO ternary compounds, ZnO:As films have been synthesized using off-axis sputtering deposition on various substrates including (100) Si and (0001) sapphire crystals. Films are grown under various growth conditions. ZnO:As targets with the atomic weight ratios of arsenic to zinc from 0.01 to 0.10 are used for film synthesis. The growth temperatures and pressures range from 350 to 550C and 5 to 150 mTorr, respectively. Argon to oxygen gas ratio for film growth is varied to examine the film quality as well. Film surface morphology, crystal structure, and compositions, are characterized using atomic force microscopy, x-ray diffraction, and energy dispersive spectroscopy, respectively. The compositions of target material and ZnO:As films grown under various conditions are then assessed. The electrical properties were also measured. The detail of these measurements will be discussed in the presentation.

Zhu, Shen↗

NASA NTRS1992

Lunar material resources: An overview

The analysis of returned lunar samples and a comparison of the physical and chemical processes operating on the Moon and on the Earth provide a basis for predicting both the possible types of material resources (especially minerals and rocks) and the physical characteristics of ore deposits potentially available on the Moon. The lack of free water on the Moon eliminates the classes of ore deposits that are most exploitable on Earth; namely, (1) hydrothermal, (2) secondary mobilization and enrichment, (3) precipitation from a body of water, and (4) placer. The types of lunar materials available for exploitation are whole rocks and their contained minerals, regolith, fumarolic and vapor deposits, and nonlunar materials, including solar wind implantations. Early exploitation of lunar material resources will be primarily the use of regolith materials for bulk shielding; the extraction from regolith fines of igneous minerals such as plagioclase feldspars and ilmenite for the production of oxygen, structural metals, and water; and possibly the separation from regolith fines of solar-wind-implanted volatiles. The only element, compound, or mineral, that by itself has been identified as having the economic potential for mining, processing, and return to Earth is helium-3.

Carter, James L.↗

NASA NTRS1972

Law and politics in outer space: A bibliography.

The materials are categorized by specific topics and by types of materials. The sources are books, articles, reports, United Nations materials, U.S. Government documents, etc. Books are listed by geographical areas, and articles are divided into what are considered to be the major space topics. Book and article sections are also divided into English and foreign language entries. A bibliographical essay introduces the literature to those unacquainted with law and politics of outer space.

White, I. L.↗

NASA NTRS1982

Io - Geochemistry of sulfur

The evidence from Voyager imaging, Earth-based spectral reflectivity studies, and thermal emission measurements combine to suggest an extremely fresh, volcanically recycled sulfur-rich crust for Io, with very shallow large-scale melting. Two present styles of volcanism are possible, depending on the thickness of local deposits of sulfur: shallow liquid sulfur magma generation with quiescent flooding, and high-temperature volcanism with violet eruption of a sulfur-iron magma driven by SO2. Evolutionary considerations preclude direct derivation of Io's lithosphere from any metal-bearing chondritic source material. Metal-free C3V- or C2M-type parent material of either primary or secondary origin is the most plausible direct antecedent of the present sulfur-rich crust. Sulfates are almost certainly important constituents of the mantle, and can participate in the recycling of reduced, dense sulfide species to prevent total extraction of sulfur into the core.

Lewis, J. S.↗

NASA NTRS1985

Petrology of types 4-6 carbonaceous chondrites

A comparative mineralogic study has been made of Coolidge, Karoonda, and new C4 chondrites in order to clarify the origin of C4-6 chondrites. It is shown that the properties of all C4-6 chondrites are consistent with an origin by metamorphism of C3-like precursors by processes analogous to those operating in ordinary chondrite parent bodies or planetesimals. However, type 4-6 material was not well mixed with type 3 material in the CV3 parent body. It is concluded that C4-6 chondrites may come from one or more separate parent bodies.

Scott, E. R. D.↗

NASA NTRS1993

Properties of Extruded PS-212 Type Self-Lubricating Materials

Research has been underway at the NASA Lewis Research Center since the 1960's to develop high temperature, self-lubricating materials. The bulk of the research has been done in-house by a team of researchers from the Materials Division. A series of self-lubricating solid material systems has been developed over the years. One of the most promising is the composite material system referred to as PS-212 or PM-212. This material is a powder metallurgy product composed of metal bonded chromium carbide and two solid lubricating materials known to be self-lubricating over a wide temperature range. NASA feels this material has a wide potential in industrial applications. Simplified processing of this material would enhance its commercial potential. Processing changes have the potential to reduce processing costs, but tribological and physical properties must not be adversely affected. Extrusion processing has been employed in this investigation as a consolidation process for PM-212/PS-212. It has been successful in that high density bars of EX-212 (extruded PM-212) can readily be fabricated. Friction and strength data indicate these properties have been maintained or improved over the P.M. version. A range of extrusion temperatures have been investigated and tensile, friction, wear, and microstructural data have been obtained. Results indicate extrusion temperatures are not critical from a densification standpoint, but other properties are temperature dependent.

Waters, W. J.↗

NASA NTRS2002

Wholly Aromatic Ether-imides. Potential Materials for n-Type Semiconductors

We report on the synthesis and characterization of a novel series low-molar-mass ether-imide rod-shaped model compounds. All ether-imides were obtained by terminating the appropriate rigid core dianhydride, i.e. pyromellitic dianhydride (PMDA), 1,4,5,8-naphthalenetetracarboxylic dianhydride (NDA), 3,3',4,4'-biphenyltetracarboxylic dianhydride (BPDA), and 3,3,4,4'-oxydiphthalic dianhydride (ODPA) with three flexible aryl-ether tails of different chain length. The mono-functional aryl-ether amines, i.e. 4-(3-phenoxy-phenoxy)-phenylamine (2) and 4-(3-phenoxy-3-phenoxy-phenoxy)-phenylamine (4), were synthesized using standard fluoro-displacement and Ullmann condensation techniques. The corresponding ether-imide model compounds were obtained in high yields using a one-step solution imidization procedure. Increasing the number of meta-substituted aryl-ether units reduces the melt transition temperatures and at the same time it increases the solubility of the model compounds. Most model compounds are crystalline solids and form isotropic melts upon heating. 2,7-Bis-(-4-phenoxy-phenyl)-benzo[Imn][3,8]phenanthroline1,3,6,8-tetraone (NDA-n0), however, displays a smectic A (SA) when cooled from the isotropic phase, followed by what appears to be either a highly ordered smectic phase or a, columnar phase. This is the first example, known to date, in which a mesophase is detected in a wholly aromatic ether-imide compound. For all compounds we present spectroscopic data and X-ray diffraction data. Cyclic voltammetry was used to determine the redox behavior and pertinent energy levels of the model compounds.

Dingemans, Theo J.↗