Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “full-scale measurements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Acoustic results obtained with upper-surface-blowing lift augmentation systems

The noise caused by the interaction of the jet exhaust and a wing was measured under static conditions for several versions of a small-scale STOL engine-over-the-wing configuration. Three basic nozzles were used in the tests; a circular nozzle, a 5:1 aspect ratio slot nozzle and a 10:1 aspect ratio slot nozzle. Various flow attachment devices were included in the study. The wing included a flap that could be positioned for nominal takeoff or approach flap settings. Far field noise data are presented for the flyover mode. The data are discussed in terms of sound power and sound pressure spectra. Implications of extending the small-scale model acoustic data to full-scale aircraft are discussed briefly and indicate a sizeable flyover noise attenuation may be achieved due to shielding by the wing.

Vonglahn, U. H.↗
NASA NTRS1973

Wind tunnel investigation of static longitudinal and lateral characteristics of a full scale mockup of a light single engine high wing airplane

The model was a full-scale mockup of a light single-engine high-wing monoplane. Tests were made over an angle-of-attack range of -4 deg to 24 deg and over a sideslip range of plus or minus 8 deg at thrust coefficients of 0, 0.14, and 0.30. Control effectiveness and hinge moments were taken on the aileron, elevator, and rudder for a full range of deflections. Downwash measurements at the tail were obtained for the range of thrust coefficient and flap deflection.

Greer, H. D.↗
NASA NTRS1974

Wind tunnel investigation of a large-scale semispan model with an unswept wing and an upper-surface blown jet flat

An investigation of the static longitudinal aerodynamic characteristics of a large-scale semispan model with an unswept wing and an upper-surface blown jet flap for lift augmentation was conducted in the Langley full-scale tunnel. The wing had an aspect ratio of 7.8 (3.9 for the semispan) and a simulated turbofan engine mounted ahead of and above the wing in a nacelle with a rectangular-exit nozzle. The flap system had three spanwise flap segments: (1) an inboard plain flap located behind the engine and having a large radius of curvature to provide a smooth upper surface to enhance the turning of the jet sheet, (2) a double-slotted midspan flap, and (3) a drooped aileron equipped with blowing boundary-layer control. The wing was also equipped with a full-span leading-edge Krueger flap with blowing boundary-layer control. In addition to the aerodynamic measurements, noise measurements were also included in the investigation for positions above and below the wing.

Smith, C. C., Jr.↗
NASA NTRS1974

The 727 airplane side inlet low-speed performance confirmation model test for refanned JT8D engines

The results of a low-speed wind tunnel test of a 0.3 scale model 727 airplane side inlet for JT8D-100 engines are presented. The objectives of the test were to develop lines for a full-scale flightworthy inlet, to evaluate inlet total pressure recovery and steady-state total pressure distortion, and to obtain model-scale distortion data which can be used in the assessment of the compatibility of the inlet with the JT8D-100 series engines. A secondary objective was to obtain internal/external cowl static pressures for the determination of nacelle loads. Two basic inlet models were tested at static, forward speed, angle-of-attack (inflow angle), and cross-wind conditions. One model was with and one without an acoustic ring. Two modifications to the models were also tested, one with the ring closer to the inlet throat and one with a larger lip. Test measurements consisted of inlet surface static pressure, engine face total pressure, inlet airflow, tunnel total pressure, tunnel total temperature and tunnel velocity. Total pressure traverses were taken directly behind the ring and strut. No dynamic measurements were taken.

Schuehle, A. L.↗
NASA NTRS1974

The M.I.T. Blowdown compressor facility

A blowdown compressor test facility has been developed which allows time-resolved aerodynamic testing of full-scale transonic compressor rotors at low cost. The rotor is brought to speed in vacuum, a diaphragm is opened, and the test gas is allowed to flow for a time of the order of 0.1 sec, during which the rotor is driven by its own inertia. Both 'steady-state' performance evaluation and detailed time resolution of the flow on the blade-passing time scale have been demonstrated for a two-ft-diam transonic rotor with a tangential Mach number of 1.2 and a nominal pressure ratio of 1.6. The steady-state performance as determined in the experiments includes an efficiency of 0.92 and a pressure ratio of 1.55 at design speed. The time-resolved measurements include the combination tone structure in the upstream flow field, resolved both axially and radially, and the wake structure downstream of the rotor, also resolved both radially and axially.

Kerrebrock, J. L.↗
NASA NTRS1975

Lightweight Vacuum Jacket for Cryogenic Insulation

The feasibility of producing a lightweight vacuum jacket using state-of-the-art technology and materials was examined. Design and analytical studies were made on a full-scale, orbital maneuvering system fuel tank. Preliminary design details were made for the tank assembly, including an optimized vacuum jacket and multilayer insulation system. A half-scale LH2 test model was designed and fabricated, and a force/stiffness proof test was conducted on the vacuum jacket. A vacuum leak rate of .000001 atmosphere ml of helium per second was measured, approximately 1500 hours of vacuum pressure were sustained, and 29 vacuum-pressure cycles were experienced prior to failure.

Barclay, D. L.↗
NASA NTRS1975

The high current transient generator, theory and operation for simulating lightning induced voltages into aerospace electrical circuits

Because of the difficulty, hazard, and cost of simulating full-scale lightning currents on flight vehicles, a nondestructive test technique using reduced-scale lightning currents was used to determine if threat level voltages will be induced into aircraft electrical circuits in the event the aircraft is actually struck by lightning. The reasoning and theory of selecting a particular simulated lightning waveshape and magnitude is given, showing that extrapolation of induced waveforms over several orders of magnitude should be avoided. The operation of high-current transient generators and hardware are described along with typical applications. The means by which voltages were generated, induced, and measured, as well as possible sources of error, are discussed.

Schulte, E. H.↗
NASA NTRS1976

Correlation of full-scale helicopter rotor performance in air with model-scale Freon data

An investigation was conducted in a transonic dynamics tunnel to measure the performance of a 1/5 scale model helicopter rotor in a Freon atmosphere. Comparisons were made between these data and full scale data obtained in air. Both the model and full scale tests were conducted at advance ratios between 0.30 and 0.40 and advancing tip Mach numbers between 0.79 and 0.95. Results show that correlation of model scale rotor performance data obtained in Freon with full scale rotor performance data in air is good with regard to data trends. Mach number effects were found to be essentially the same for the model rotor performance data obtained in Freon and the full scale rotor performance data obtained in air. It was determined that Reynolds number effects may be of the same magnitude or smaller than rotor solidity effects or blade elastic modeling in rotor aerodynamic performance testing.

Yeager, W. T., Jr.↗
NASA NTRS1978

Status of aerial applications research in the Langley vortex research facility and the Langley full-scale wind tunnel

Small scale models of agricultural airplanes were tested and numerical methods were utilized to study interactions between the airplane wake and the dispersed spray and granular materials. Methods were developed to measure and predict dispersal transport and wake characteristics and dispersal techniques to obtain interactions more favorable to wide, uniform deposition patterns and reduced drift. In the full scale wind tunnel, full scale agricultural airplanes and dispersal systems for both liquid and solid applications were evaluated to improve aircraft aerodynamics and dispersal systems efficiency. The program status in these two facilities is reported with emphasis on wake interactions and dispersal systems research.

Jordan, F. L., Jr.↗
NASA NTRS1978

Full-scale testing of an Ogee tip rotor

Full scale tests were utilized to investigate the effect of the ogee tip on helicopter rotor acoustics, performance, and loads. Two facilities were used: the Langley whirl tower and a UH-1H helicopter. The text matrix for hover on the whirl tower involved thrust values from 0 to 44 480 N (10,000 lb) at several tip Mach numbers for both standard and Ogee rotors. The full scale testing on the UH-1H encompassed the major portion of the flight envelope for that aircraft. Both near field acoustic measurements and far field flyover data were obtained for both the ogee and standard rotors. Data analysis of the whirl tower test shows that the ogee tip does significantly diffuse the tip vortex while providing some improvement in hover performance at low and moderate thrust coefficients. Flight testing of both rotors indicates that the strong impulsive noise signature of the standard rotor can be reduced with the ogee rotor. Analysis of the spectra indicates a reduction in energy in the 250 Hz and 1000 Hz range for the ogee rotor. Forward flight performance was significantly improved with the ogee configuration for a large number of flight conditions. Further, rotor control loads were reduced through use of this advanced tip rotor.

Mantay, W. R.↗
NASA NTRS1978

The free jet as a simulator of forward velocity effects on jet noise

A thorough theoretical and experimental study of the effects of the free-jet shear layer on the transmission of sound from a model jet placed within the free jet to the far-field receiver located outside the free-jet flow was conducted. The validity and accuracy of the free-jet flight simulation technique for forward velocity effects on jet noise was evaluated. Transformation charts and a systematic computational procedure for converting measurements from a free-jet simulation to the corresponding results from a wind-tunnel simulation, and, finally, to the flight case were provided. The effects of simulated forward flight on jet mixing noise, internal noise and shock-associated noise from model-scale unheated and heated jets were established experimentally in a free-jet facility. It was illustrated that the existing anomalies between full-scale flight data and model-scale flight simulation data projected to the flight case, could well be due to the contamination of flight data by engine internal noise.

Ahuja, K. K.↗
NASA NTRS1979

Scaling characteristics of MPD propulsion

Experiments in which a high-power, quasi-steady MPD thruster is scaled down by a factor of two indicate that the key features of MPD thruster operation are replicated in the smaller version. Voltage-current data over a 24:1 mass flow range show that the ablation onset parameter is constant for each thruster, although the constant is not the same. Time-integrated photographs of the discharge radiance reveal strikingly similar features at scaled values of current and mass flow. The measured terminal properties of the half-scale thruster are similar to the full-scale thruster, but the regime of operation is smaller and generally less efficient, except within a restricted range of arc current and mass flow.

Mead, F. B., Jr.↗
NASA NTRS1980

Upper surface blowing noise of the NASA-Ames quiet short-haul research aircraft

An experimental study of the propulsive-lift noise of the NASA-Ames quiet short-haul research aircraft (QSRA) is described. Comparisons are made of measured QSRA flyover noise and model propulsive-lift noise data available in references. Developmental tests of trailing-edge treatments were conducted using sawtooth-shaped and porous USB flap trailing-edge extensions. Small scale parametric tests were conducted to determine noise reduction/design relationships. Full-scale static tests were conducted with the QSRA preparatory to the selection of edge treatment designs for flight testing. QSRA flight and published model propulsive-lift noise data have similar characteristics. Noise reductions of 2 to 3 dB were achieved over a wide range of frequency and directivity angles in static tests of the QSRA. These noise reductions are expected to be achieved or surpassed in flight tests planned by NASA in 1980.

Bohn, A. J.↗
NASA NTRS1980

Full scale visualization of the wing tip vortices generated by a typical agricultural aircraft

The trajectories of the wing tip vortices of a typical agricultural aircraft were experimentally determined by flight test. A flow visualization method, similar to the vapor screen method used in wind tunnels, was used to obtain trajectory data for a range of flight speeds, airplane configurations, and wing loadings. Detailed measurements of the spanwise surface pressure distribution were made for all test points. Further, a powered 1/8 scale model of the aircraft was designed, built, and used to obtain tip vortex trajectory data under conditions similar to that of the full-scale test. The effects of light wind on the vortices were demonstrated, and the interaction of the flap vortex and the tip vortex was clearly shown in photographs and plotted trajectory data.

Cross, E. J., Jr.↗
NASA NTRS1939

Tests of NACA 0009, 0012, and 0018 Airfoils in the Full-Scale Tunnel

An investigation was conducted in the NACA full-scale wind tunnel to determine the aerodynamic characteristics of the NACA 0009, 0012, and 0018 airfoils, with the ultimate purpose of providing data to be used as a basis for comparison with other wind-tunnel data, mainly in the study of scale and turbulence effects. Three symmetrical 6 by 36-foot rectangular airfoils were used. The Reynolds number range for minimum drag was form 1,800,000 to 7,000,000 and for maximum lift, from 1,700,000 to 4,500,000. The effect of rounded tips was determined for each of the airfoils. Tests were also made of the NACA 0012 airfoil equipped with a 0.20c full-span split flap hinged at 0.80c. Tuft surveys were included to show the progressive breakdown of flow near maximum lift. Momentum surveys were made in conjunction with force measurements at zero lift as an aid in converting force-test data to section coefficients.

Goett, Harry J↗
NASA NTRS1961

Preliminary Base Pressures Obtained from the X-15 Airplane at Mach Numbers from 1.1 to 3.2

Base pressure measurements have been made on the fuselage, 10 deg.-wedge vertical fin, and side fairing of the X-15 airplane. Data are presented for Mach numbers between 1.1 and 3.2 for both powered and unpowered flight. Comparisons are made with data from small-scale-model tests, semiempirical estimates, and theory. The results of this preliminary study show that operation of the interim rocket engines (propellant flow rate approximately 70 lb/sec) reduces the base drag of the X-15 by 25 to 35 percent throughout the test Mach number range. Values of base drag coefficient for the side fairing and fuselage obtained from X-15 wind-tunnel models were adequate for predicting the overall full-scale performance of the test airplane. The leading-edge sweep of the upper movable vertical fin was not an important factor affecting the fin base pressure. The power-off base pressure coefficients of the upper movable vertical fin (a 10 deg. wedge with chord-to-thickness ratio of 5.5 and semispan-to-thickness ratio of 3.2) are in general agreement with the small-scale blunt-trailing-edge-wing data of several investigators and with two-dimensional theory.

Saltzman, Edwin J.↗
NASA NTRS1961

Aerodynamic Characteristics, Temperature, and Noise Measurements of a Large-Scale External-Flow Jet-Augmented-Flap Model with Turbojet Engines Operating

An investigation has been conducted in the Langley full-scale tunnel on a large-scale model powered by turbojet engines with flattened rectangular nozzles. The wing had 35 deg. sweep of the leading edge, an aspect ratio of 6.5, a taper ratio of 0.31, and NACA 65(1)-412 and 65-408 airfoils at the root and tip. The investigation included measurements of the longitudinal aerodynamic characteristics of the model with half-span and full-span flaps and measurements of the sound pressure and skin temperature on the portions of the lower surface of the wing immersed in the jet flow. The tests were conducted over a range or angles of attack from -8 to 16 deg. for Reynolds numbers from 1.8 x 10(exp 6) to 4.4 x 10(exp 6) and a range of momentum coefficients from 0 to 2.0. In general, the aerodynamic results of this investigation made with a large-scale hot-jet model verified the results of previous investigations with small models powered by compressed-air jets. Although blowing was only done over the inboard portion of the wing, substantial amounts of induced lift were also obtained over the outboard portion of the wing. Skin temperatures were about 340 F and wing heating could be handled with available materials without cooling. Random acoustic loadings on the wing surface were high enough to indicate that fatigue failure from this source would require special consideration in the design of an external-flow jet flap system for an airplane.

Fink, Marvin P.↗
NASA NTRS1960

Landing Characteristics of a Reentry Capsule with a Torus-Shaped Air Bag for Load Alleviation

An experimental investigation has been made to determine the landing characteristics of a conical-shaped reentry capsule by using torus-shaped air bags for impact-load alleviation. An impact bag was attached below the large end of the capsule to absorb initial impact loads and a second bag was attached around the canister to absorb loads resulting from impact on the canister when the capsule overturned. A 1/6-scale dynamic model of the configuration was tested for nominal flight paths of 60 deg. and 90 deg. (vertical), a range of contact attitudes from -25 deg. to 30 deg., and a vertical contact velocity of 12.25 feet per second. Accelerations were measured along the X-axis (roll) and Z-axis (yaw) by accelerometers rigidly installed at the center of gravity of the model. Actual flight path, contact attitudes, and motions were determined from high-speed motion pictures. Landings were made on concrete and on water. The peak accelerations along the X-axis for landings on concrete were in the order of 3Og for a 0 deg. contact attitude. A horizontal velocity of 7 feet per second, corresponding to a flight path of 60 deg., had very little effect upon the peak accelerations obtained for landings on concrete. For contact attitudes of -25 deg. and 30 deg. the peak accelerations along the Z-axis were about +/- l5g, respectively. The peak accelerations measured for the water landings were about one-third lower than the peak accelerations measured for the landings on concrete. Assuming a rigid body, computations were made by using Newton's second law of motion and the force-stroke characteristics of the air bag to determine accelerations for a flight path of 90 deg. (vertical) and a contact attitude of 0 deg. The computed and experimental peak accelerations and strokes at peak acceleration were in good agreement for the model. The special scaling appears to be applicable for predicting full-scale time and stroke at peak acceleration for a landing on concrete from a 90 deg. flight path at a 0 deg. It appears that the full-scale approximately the same as those obtained from the model for the range of attitudes and flight paths investigated.

McGehee, John R.↗