Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “superior rate performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Cold compressor performance and energy consumption improvements at Jefferson Lab’s Central Helium Liquefiers

Abstract Jefferson Lab operates two central helium liquefiers (CHLs) which both utilize full cold compression from the saturation pressure at operating temperature (approximately 2.1 K) to just over atmospheric pressure. The original plant, CHL1, was recently outfitted with a replacement subatmospheric cold box (SC1R) containing state-of-the-art cold compressor technology, while the newer plant, CHL2, uses an older cold compressor system. In both cases, the heat of compression is absorbed at low temperature at the expense of electrical power consumed by the warm compressors. Due to the superior efficiency and turndown capabilities of SC1R, a new operating mode has been identified for CHL1 in which the required number of operating warm compressors is reduced by one. A cost-based method for optimizing cold compressor stability and efficiency has been developed and applied to CHL2, improving its turndown and lowering the warm compressor discharge pressure. As a result of these efforts, power consumption of the combined CHLs during normal operations has been reduced by nearly 10%, or a total of 650 kW. The observed performance of CHL1 with SC1R, as well as the cold compressor optimization method, leading to this improved energy consumption rate will be discussed in detail.

Mastracci, B [Thomas Jefferson National Accelerato↗
DOE OSTI2024

Engineered MXene quantum dots for micro-supercapacitors with excellent capacitive behaviors

Micro-supercapacitors (MSCs) have drawn tremendous attention as promising candidates to power miniaturized portable/wearable electronics, but they still suffer from unsatisfactory electrochemical performance (e.g., insufficient energy density, mediocre rate capability), thus impeding their widespread applications. Here, a synergistic surface and structure engineering strategy achieved by downsizing to quantum dot scale, doping of heteroatoms, and introducing defects and functional groups is proposed to regulate the physicochemical properties of Ti 3 C 2 T x MXene. Encouragingly, the resulting MSCs based on defect-rich nitrogen-doped Ti 3 C 2 T x quantum dots (QDs) possess excellent electrochemical performance as demonstrated by large operating voltage (3.0 V in ionic liquid and 1.0 V in aqueous electrolyte), perfect rectangular CV shape even at 1000 V·s -1 , high volumetric capacitance of 33.1 F·cm -3 , and superior cycling stability after 10000 cycles. By employing experimental characterizations and density functional theory calculations, the remarkable performance of the MSCs is mainly due to the special chemical states as well as the unique surface and structural features of Ti 3 C 2 T x QDs, which offer abundant active sites, shorten ion diffusion pathways, promote ion/electron transports, and provide enhanced capacitance. Finally, this work provides a new strategy for the design of high-performance MSCs and a reference for the applications of MXene QDs in other energy-related fields.

42 ENGINEERING↗
DOE OSTI2025

Interface-engineered (AlMnCoNiZn) 3 O 4 @PPy nanocomposites for superior lithium storage: Mechanism and performance

The practical application of graphite anodes in lithium-ion batteries (LIBs) is constrained by low specific capacity (372 mAh g -1 ) and sluggish kinetics. Here, to address these limitations, our present study focuses on high-entropy oxides (HEOs), which offer high theoretical capacity and structural stability. We synthesized spinel-structured (AlMnCoNiZn) 3 O 4 nanoparticles via a solution combustion method and fabricated an (AlMnCoNiZn) 3 O 4 @polypyrrole (PPy) nanocomposite through in-situ polymerization. Our electrochemical tests demonstrate that the PPy modification significantly enhances performance. While the pristine (AlMnCoNiZn) 3 O 4 delivered 445 mAh g −1 after 100 cycles at 100 mA g −1 and 350 mAh g −1 after 1000 cycles at 1000 mA g −1 , the (AlMnCoNiZn) 3 O 4 @PPy composite achieved 695 mAh g −1 after 100 cycles and maintained 675 mAh g −1 after 1000 cycles. Furthermore, the composite improved rate capacity at 1000 mA g −1 from 211 mAh g −1 to 403 mAh g −1 . This work highlights how conductive and flexible polymer modifications can dramatically improve the electrochemical properties of HEOs. The developed (AlMnCoNiZn) 3 O 4 @PPy composite provides a promising direction for designing advanced anodes to meet next-generation energy storage demands.

Anodes material↗
DOE OSTI2023

Continuous-flow reactor with superior production rate and stability for CO 2 reduction using semiconductor photocatalysts

Semiconductor photocatalyst approaches for solar CO 2 reduction are attractive due to their simplicity but have lagged in efficiency compared to less-integrated photoelectrochemical (PEC) approaches and to electrolysis reactors. We identify poor mass transport and catalyst deactivation as key constraints. To address them, we have developed a continuous-flow photocatalytic reactor system allowing us to control the triple-phase interface on the photocatalyst surface using the liquid and reactant gas flow rates. With the goal of selectively producing CO, the reactor is optimized by controlling the pressure and flow rates of the reactant gas and electrolyte in contact with both sides with the intermediately placed catalyst. In comparison to batch reactors with an immobile photocatalyst bed and gas phase CO 2 or CO 2 purged water, 10–24 times higher production rates are achieved for photocatalysts such as TiO 2 , ZnO, C 3 N 4 , and CdS by simply changing to the designed flow-type photoreactor without any catalyst modification. In addition, CO selectivity (93.2%) and long-term stability (>780 min) using the designed reactor are significantly enhanced compared to using the batch reactors (71.7%, <180 min for reduced 50% activity). Here, we propose that the enhanced mass transport on the photocatalyst surface accelerates the desorption of the initial photolysis product, CO, and prevents the poisoning effect from deactivating photocatalyst activity. This study has the potential to facilitate the utilization of semiconductor-based photocatalytic reactions for achieving superior performance wih gaseous reactants.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

The role of Li doping in layered/layered Na x Li y Ni 0.4 Fe 0.2 Mn 0.4 O 2 intergrowth electrodes for sodium ion batteries

Here, the layered NaTMO 2 (TM = Ni, Fe, Mn) materials with the O3-type structure are attractive as positive electrodes for sodium ion batteries because of their high theoretical capacity. Additionally, Li doping in these materials has been shown to offer substantial enhancements to their electrochemical properties by promoting the formation of intergrowth structures, which are combinations of specific phases. However, the mechanism by which the intergrowth modifies the electrochemical properties is often unclear. Systematic variation of Li content in Na x Li y Ni 0.4 Fe 0.2 Mn 0.4 O 2 (NFM-Li y ) was conducted to identify its role in structural modification and electrochemical performance. Li contents of 0.15 and greater generate a layered/layered Na-O3/Li-O’3 intergrowth structure. 7 Li and 23 Na nuclear magnetic resonance and x-ray absorption spectroscopy identify that when the total solubility for alkali ions in the layered structure is exceeded, Li continues to form the Li-O’3 phase while the excess Na forms residual sodium compounds such as Na 2 O. Higher Li content is associated with improved capacity retention in the initial cycles from the superior stability of the mechanically linked NaO3/Li-O’3 structure that suppresses the P3 to OP2 phase transition during charge. However, high Li contents are associated with increased rates of parasitic side reactions that reduce long-term cycling stability. These side reactions are associated with the instability of the cathode-electrolyte interphase, which can be partially mitigated by atomic layer deposition (ALD) coating with alumina, which significantly enhances the capacity retention and Coulombic efficiency over many cycles. Overall, we find that the layered/layered Na-O3/Li-O’3 intergrowth structure is able to provide structural stability and suppress undesired phase transformations but is overwhelmed by the increased reactivity of the surface if not protected by surface coating.

25 ENERGY STORAGE↗
DOE OSTI2024

Construction of MoS 2 /NiS 2 heterostructure with fast interfacial reaction kinetics for ultrafast sodium storage

Constructing heterostructure is a valid method to reinforcing sodium storage performance of transition metal chalcogenides materials. Herein, a simple, safe and controllable one step hydrothermal method is proposed to synthesize MoS 2 /NiS 2 heterostructure. Due to the difference in band gaps and work functions of MoS 2 and NiS 2 , the charges are redistributed at the MoS 2 /NiS 2 heterointerfaces, thereby accelerating the migration of electrons and Na + . The heterointerfaces provide extra active sites for storing Na + , thus increasing the sodium storage capacity of the heterostructure. Furthermore, the distinct redox potentials of NiS 2 and MoS 2 promote the structural stability of MoS 2 /NiS 2 heterostructure during the electrochemical reaction processes. Consequently, the obtained MoS 2 /NiS 2 heterostructure exhibits superior rate properties (339.4 mAh g –1 at 10 A g –1 ) and ultra-stable cycling stability (480.5 mAh g –1 after 350 cycles at 1 A g –1 ). Finally, this paper presents a valid strategy for creating heterostructure anodes with excellent sodium storage properties.

25 ENERGY STORAGE↗
DOE OSTI2024

Low Melting Temperature Gallium–Indium Liquid Metal Anode for Solid-State Li-Ion Batteries

Solid-state Li-ion batteries are attracting attention for their enhanced safety features, higher energy density, and broader operational temperature range compared to systems based on liquid electrolytes. However, current solid-state Li-ion batteries face performance challenges, such as suboptimal cycling and poor rate capabilities, often due to inadequate interfacial contact between the solid electrolyte and electrodes. To address this issue, we incorporated a gallium–indium (Ga–In) liquid metal as the anode in a solid-state Li-ion battery setup, employing Li 6 PS 5 Cl as the solid electrolyte. Operating at room temperature, this configuration achieved an initial capacity of 389 mAh g –1 and maintained 88% of this capacity after 30 cycles at a 0.05 C rate. It also demonstrated a capacity retention of 66% after 500 cycles at a 0.5 C rate. In comparison to solid anode materials, such as tin, the Ga–In liquid metal exhibited superior cycling stability and rate capacity, which is due to the self-healing and fluid properties of the alloy that ensure stable interfacial contact with solid electrolytes. In situ X-ray diffraction (XRD) and ex situ scanning electron microscope (SEM) analyses revealed that indium does not directly participate in the lithiation/delithiation process. Instead, it helps maintain the alloy’s low melting point, facilitating its return to a liquid state after delithiation. In a comparative analysis of stack pressure during cycling in cells utilizing Ga–In liquid metal and tin, the Ga–In liquid metal cell demonstrated an ability to buffer pressure increases associated with deformation. In conclusion, these findings suggest a promising approach for enhancing solid-state batteries by integrating liquid metal anodes, which improve interfacial contact and stability.

Alloys↗
DOE OSTI2022

Dehydrogenation of Propane and n -Butane Catalyzed by Isolated PtZn 4 Sites Supported on Self-Pillared Zeolite Pentasil Nanosheets

Propene and 1,3-butadiene are important building-block chemicals that can be produced by dehydrogenation of propane and butane over Pt catalysts. The challenge is to develop highly active and selective catalysts that are resistant to deactivation by Pt sintering and coke formation. We have recently shown that these objectives can be met for propane dehydrogenation using atomically dispersed Pt atoms anchored to neighboring ≡SiOZn-OH groups bonded to the framework dealuminated zeolite BEA. In the present study, we demonstrate that significantly superior performance can be achieved by using self-pillared pentasil (SPP) zeolite nanosheets. Following catalyst reduction in H 2 , atomic-resolution, scanning transmission electron microscopy (STEM) and X-ray absorption spectroscopy (XAS) indicate that Pt is stabilized in structures well approximated as (≡Si-O-Zn) 4-5 Pt. These species are highly active, selective, and stable for propane dehydrogenation (PDH) to give propene and for n-butane dehydrogenation (BDH) to give 1,3-butadiene. No catalyst deactivation was observed after 12 days of time on stream, and the selectivity remained at nearly 100% for PDH conducted at 823 K and a weight hourly space velocity (WHSV) of 1,350 h -1 . The apparent rate coefficient for PDH over this catalyst is significantly higher than that reported previously for Pt-containing catalysts. For BDH at 823 K and a WHSV of 3560 h -1 , the selectivity to butene isomers and 1,3-butadiene is 98.9%, and the selectivity to 1,3-butadiene is 45%. Here, we propose that the high catalyst stability observed during PDH and BDH is a consequence of a large fraction of the Pt-containing centers being located on the external surface of the zeolite nanosheets, where nascent coke precursors can desorb before condensing to form coke.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Real-time image denoising of mixed Poisson–Gaussian noise in fluorescence microscopy images using ImageJ

Fluorescence microscopy imaging speed is fundamentally limited by the measurement signal-to-noise ratio (SNR). To improve image SNR for a given image acquisition rate, computational denoising techniques can be used to suppress noise. However, common techniques to estimate a denoised image from a single frame either are computationally expensive or rely on simple noise statistical models. These models assume Poisson or Gaussian noise statistics, which are not appropriate for many fluorescence microscopy applications that contain quantum shot noise and electronic Johnson–Nyquist noise, therefore a mixture of Poisson and Gaussian noise. In this paper, we show convolutional neural networks (CNNs) trained on mixed Poisson and Gaussian noise images to overcome the limitations of existing image denoising methods. The trained CNN is presented as an open-source ImageJ plugin that performs real-time image denoising (within tens of milliseconds) with superior performance (SNR improvement) compared to conventional fluorescence microscopy denoising methods. The method is validated on external datasets with out-of-distribution noise, contrast, structure, and imaging modalities from the training data and consistently achieves high-performance ( > <#comment/> 8 d B ) denoising in less time than other fluorescence microscopy denoising methods.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

In Situ Synthesis of Phosphate-Based CelloMOF as a Promising Separator for Li–Ion Batteries

Nowadays, battery separators play a critical role in determining the sustainability, electrochemical efficiency, and safety of lithium-ion batteries (LIBs). In this contribution, we developed fire-resistant composite membranes called CelloMOF by in situ grafting of metal-organic framework, ZIF-67, onto phosphorylated cellulose nanofibers (P-CNFs) followed by a vacuum filtration process akin to papermaking. The hybrid ZIF-67@P-CNF membrane exhibits superior properties than a polyolefin-based commercial separator (CS) in terms of enhanced thermal and dimensional stability, flame-retardant properties, better surface wettability, and improved electrolyte uptake. Thermal dimensional stability tests revealed that the ZIF-67@P-CNF separator maintained its structure even at 200 °C, whereas CS suffered severe shrinkage, potentially leading to internal short circuits. Combustion tests showed a peak heat release rate (PHRR) of 34.5 W/g and a total heat release (THR) of 1.61 kJ/g for ZIF-67@P-CNF, significantly lower than the PHRR (1111.82 W/g) and THR (40.89 kJ/g) of CS. The composite separator also demonstrated significantly improved wettability, with a contact angle of 32 ± 1.04°, compared to 92 ± 1.07° for CS, highlighting its hydrophilic nature. Electrochemical evaluations in LiFePO 4 /Li half-cells indicated a higher discharge capacity of 149 mA h g -1 at 0.2 C and superior capacity retention of 86% after 50 cycles, outperforming CS (145 mA h g -1 and 84%, respectively). In conclusion, these results underscore the potential of the ZIF-67@P-CNF membrane to advance safe, high-performance LIBs by addressing critical challenges in thermal stability, flame retardancy, and electrolyte compatibility.

ZIF-67↗
DOE OSTI2021

A Novel Hollow Fiber Membrane Reactor for High Purity H 2 Generation from Thermal Catalytic NH 3 Decomposition (Final Report)

Ammonia (NH 3 ), as a promising carbon neutral liquid fuel (CNLF) and an effective H 2 source, can be synthesized from air and water (N 2 extracted from air and H 2 from water) using renewable energy sources. To produce H 2 as an intermediate, it is essential to develop effective and economic NH 3 decomposition technologies. We have been developing an innovative hollow fiber membrane reactor for high purity H 2 generation from thermal catalytic NH 3 decomposition. The objective of the proposed research is to fabricate a compact and robust prototype with high energy efficiency (>80%) to deliver high purity (>99%) H2 at high rate per volume (>0.15 g H 2 /h/cm 3 ) from NH3 decomposition at low temperature (<450 °C) and high conversion (>99%). Our overall technical approach is to effectively combine an active catalyst for NH 3 decomposition with a selective H 2 membrane separation process in a novel, compact modular system to generate high purity H 2 and simultaneously achieve high NH 3 conversion and optimize the entire system energy efficiency. This novel integrated membrane reactor design, together with low-cost, highly active Ru-based catalyst, makes it most appropriate for the project objective. The proposed applied research and development work, therefore, represents an innovative and transformational solution to H 2 generation from thermal catalytic NH 3 decomposition. During the course of our research we i) synthesized and characterized ruthenium(Ru)-based catalysts, evaluated their catalytic performance for NH 3 decomposition and optimized the catalyst composition and performance based on machine learning, ii) prepared SAPO-34, MFI membranes on α-alumina hollow fibers and measured their performance for H 2 /N 2 , H 2 /N 2 /NH 3 separation and evaluated carbon molecular sieve (CMS) and Pd/Ag membranes for H 2 /N 2 , H 2 /N 2 /NH 3 separation at different conditions, iii) designed and evaluated several types of membrane reactors for H 2 production from NH 3 decomposition, and iv) evaluated the H 2 delivery cost base on catalysts development, membrane development and membrane reactor. For 3,1,12 RuYK catalyst, H 2 productivity of 6.35 mmol/min/gcat with NH 3 conversion of 95~98% was achieved at 5 bar and 400 °C; for SAPO-34 membrane, the best membrane showed H 2 permeance of 7.56×10 -7 mol/(m 2 ∙s∙Pa) and H 2 /N 2 selectivity of 23.1 at 20 °C; For CMS and Pd/Ag membranes, both showed superior stability for 71%H 2 /24%N 2 /5%NH 3 mixture separation at 450 °C and 7 bar for over 120 h; for the membrane reactor, high H 2 purity of >99.99% with NH 3 conversion of >99.4% were achieved in Pd/Ag membrane reactor at 450 °C, and the NH 3 concentration was always below 10 ppb in H 2 product. The H 2 generation rate was calculated to be as high as 0.47 g/h/cm 3 and the energy efficiency was calculated to be 88%. The membrane reactor showed superior stability for over 370 h and high H 2 purity, H 2 production rate and NH 3 conversion. Based on calculation, the H 2 delivery cost can be as low as $3.66/kg.

08 HYDROGEN↗
DOE OSTI2022

Effects of a composite flame retardant system on the flame retardancy and mechanical performance of epoxy resin adhesive

Abstract A flame‐retarded epoxy resin (ER) adhesive with strong flame retardancy and adhesion performance was prepared. The coated ammonium polyphosphate (MFAPP), melamine (MEL), and organic montmorillonite (OMMT) were mixed to prepare a composite flame retardant. It was subsequently blended with a toughened ER thoroughly and then the mixture was cured with polyamide. The resultant ER adhesive thermosets achieved UL‐94 V‐0 rating during vertical burning test, and the limiting oxygen index value was as high as 31.6%. The shear strength of the ER adhesive was 27.9 MPa when 25 wt% MFAPP/MEL/OMMT was introduced. Compared with the pure adhesive, the flame retardant epoxy adhesive maintained outstanding adhesion performance because of the good compatibility between the composite flame retardant additives and the toughened ER adhesive. Cone calorimetry tests indicated that the release of heat and smoke were obviously declined with the incorporation of the composite flame retardant system in comparison to pure ER adhesive thermoset. The investigation of flame retardant mechanism revealed that the composite MFAPP/MEL/OMMT flame retardant system stimulated the generation of highly expanded, integral, and strong char layer and the formed char layer exerted superior insulation effect during combusiton. The present work provided an alternative approach to prepare flame retardant ER adhesive with the similar excellent adhesive performance.

Li, Sheng↗
DOE OSTI2020

Dirty dishes or dirty laundry? Comparing two methods for quantifying American consumers' preferences for load management in a smart home

One challenge of transitioning to renewable energy is that household electricity use and renewable generation are often misaligned. Smart home energy management systems hold promise for shifting usage to match generation, but these systems need to be designed with the occupants’ preferences in mind. The purpose of the present research is to compare two approaches for collecting and modeling consumers’ load management preferences, both of which are amenable to use in a home energy management system. Specifically, we examine the performance of Simple Multi-Attribute Rating Technique Exploiting Ranks (SMARTER) and Analytic Hierarchy Process (AHP) in quantifying consumers’ preferences regarding air temperature (air conditioning and heating), water heating, dishwashing, clothes washing and drying, monetary costs, environmental impacts, and comfort/convenience. Two studies are presented: Study 1 examines the SMARTER approach, and Study 2 focuses on the AHP approach. In both studies, online surveys (N SMARTER = 956 and N AHP = 1023) were conducted to elicit preferences from participants across the United States. The preferences modeled by both approaches were validated based on (a) their ability to predict participants’ choices in a Discrete Choice Experiment and (b) their convergence with previous research on load-shifting behavior. The validation procedure suggests that the SMARTER approach is superior in modeling consumers’ preferences for load management. Overall, this research lays the groundwork for designing a smart home interface capable of collecting occupants’ preferences and using those preferences to deliver improved occupant comfort, lower operating costs, reduced environmental impact, and more significant demand response than exists today.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

A Comprehensive Experimental Study on Microstructure‐Graded Graphite Anodes for Enhancing Fast‐Charging Capability of Lithium‐Ion Batteries

Lithium‐ion batteries with high gravimetric capacity density and improved cycle life performance under fast‐charging conditions are crucial for widespread electric vehicle (EV) adoption. This study investigates how designing graphite anode microstructure, specifically porosity, and particle‐size gradients, improves lithium‐ion (Li + ) transport during fast‐charging conditions. Three‐layered graphite anodes with varying porosity (24%, 36%, 46%) and particle size gradients (3, 5, 10 μm) were compared to a conventional single‐layered electrode in half‐cell configurations. At room temperature and high discharge rate (2C), both gradient structures showed significantly enhanced capacity retention (80% and 67% vs. 50%) compared to the conventional electrode, highlighting the effectiveness of microstructure engineering for fast charging. The study also investigated the temperature's impact on cycle life. After 200 cycles at 2°C and 45°C, all gradient structures demonstrated superior capacity retention (≈80%) compared to the conventional electrode (35%), suggesting the gradients mitigate degradation rate at high temperatures. Electrochemical impedance spectroscopy confirmed superior Li+ diffusion and lower resistivity in gradient electrodes. Simulations explored the influence of gradient profiles on reaction kinetics across the electrode thickness. Overall, this research demonstrates that the fast‐charging capability of graphite electrodes can be greatly enhanced by engineering the electrode microstructure, thereby making EV technology more accessible and appealing.

Ahmadi, Soma↗
DOE OSTI2022

Novel textured surfaces for superior corrosion mitigation in molten carbonate salts for concentrating solar power

Corrosion of metals in contact with molten salts used for thermal energy storage and heat transport at high temperatures is a serious impediment to the development of next-generation concentrating solar thermal systems. Toward addressing this limitation, novel multiscale fractal-textured Ni coatings on a variety of substrate alloys are presented in this study for exceptional corrosion mitigation in molten carbonate salts at a high temperature. Strongly adherent, durable, single-layer, and double-layer multiscale fractal coatings were fabricated using the electrodeposition method. Corrosion performance of the coatings on SS310, SS316, SS347, and In800H was studied in molten carbonate salt (32% Li 2 CO 3 +33% Na 2 CO 3 +35% K 2 CO 3 ) at 750 °C. Single-layer coatings are stable up to 300 h immersion, whereas double-layer coatings are stable beyond 750 h. The corrosion rate of double-layer Ni coatings on ferrous alloys was reduced by as much as 60% from that of uncoated surfaces and was about 18% below that of higher cost, high Ni content Ha230. The study represents the first-ever report of corrosion characteristics of alloys in carbonate salts at 750 °C and the first demonstration of a means of dramatically reducing corrosion in carbonate salts at a high temperature. The article is significant in that it provides a viable approach for low-cost structural alloys to be corrosion-resistant to molten carbonate heat transfer fluids and storage media in high-temperature concentrating solar thermal applications. Furthermore, the corrosion-resistant coatings provide opportunities for the use of low-cost, ferritic alloys instead of the expensive nickel-based alloys in practice.

14 SOLAR ENERGY↗
DOE OSTI2022

Spontaneous carrier generation and low recombination in high-efficiency non-fullerene solar cells

The current research reveals the unique photo physical properties and carrier generation mechanisms of high efficiency non-fullerene acceptor-based organic photovoltaic blends. The analysis of device performance, morphology, and photo physics reveals that the interface carrier generation cannot support the device's current output. It is seen that primary photon excitons can dissociate into charge carriers in Y6, which displays a time scale of ∼0.3 ps with polaron yields above 28% in neat and blended thin films. This characteristic in combination with a large exciton diffusion length enables high morphology tolerance in Y6-overloaded blends. The carrier generation process is also combined with recombination studies. The recombination rate quantified by flux-dependent transient absorption measurements yields less than 5% total recombination and nearly 0% geminate recombination. Furthermore, these results define the advantages of the Y6 non-fullerene acceptor (NFA) and reveal the fundamental importance of developing new NFA materials with superior photo physical properties.

14 SOLAR ENERGY↗
DOE OSTI2025

Charge Reduction and Performance Analysis of a Heat Pump Water Heater Using R290 as a Refrigerant—A Field Study

Heat pump water heaters (HPWHs) are a proven technology for water heating that has been commercialized. The adoption of HPWHs for domestic and commercial water heating is growing rapidly because of their superior performance compared with alternative water heating methods. Whereas most existing systems use R-134a as a working refrigerant, R290 has gained major attention owing to its superior thermodynamic properties. The goal of the current study is to assess the performance of residential HPWH with R290 as a direct refrigerant replacement for R134a. Two units of a 50 gal HPWH were used in this experimental study. A baseline unit contained R134a refrigerant, and a prototype unit contained R290 refrigerant. The prototype unit was developed through the modification of a commercially available HPWH unit to achieve a low charge of R290 refrigerant. Another major modification was the replacement of the baseline compressor with a compressor designed for R290. Tests were conducted in a field environment (a research and demonstration house) using programmed drawn profiles daily. The prototype that reduced the charge by 43–47% provided displayed performance comparable to the baseline unit regarding first-hour rating (FHR) and the uniform energy factor (UEF).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Understanding fundamental effects of Cu impurity in different forms for recovered LiNi 0.6 Co 0.2 Mn 0.2 O 2 cathode materials

When identifying and developing lithium ion battery recycling technologies, understanding the role of impurities is always a concern as they may have an impact on electrochemical performance, material stability, or lifetime for recovered active materials. In this work we show that Cu impurity in different forms could play very different roles on the recovered LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622). Cu metal impurity could easily short the cell, while Cu ion impurity could play a positive role due to partially substitution of the Ni 2+ sites to lower the cation mixing degree. In specific, NCM622 material with certain amount (0.34 at%) of Cu ion impurity delivers high initial specific charge/discharge capacity of 211.8 and 186.0 mAh g -1 at 0.05 C, which are 12.2 and 14.1 mAh g -1 higher than those of virgin NCM622 cathode. Moreover, a superior retention capacity of 171.3 mAh g -1 after 90 cycles at 0.33 C, and striking rate capability are achieved in this NCM622 cathode sample. These results clearly indicate that Cu metal impurity should be avoided and the ionic Cu impurity should be controlled with optimal concentration during recycling process for spent LIBs.

25 ENERGY STORAGE↗