Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “furnaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Early age hydration and application of blended magnesium potassium phosphate cements for reduced corrosion of reactive metals

Highlights: • Magnesium potassium phosphate cements were studied for nuclear waste encapsulation. • The optimised formulation in this study was determined to be 0.24 w/s ratio. • Different reaction kinetics were discovered for the FA/MKPC and BFS/MKPC binders. • Struvite-K was the only crystalline reaction product observed via in-situ SXPD. • Uranium trials revealed MKPC corrosion was reduced compared to a UK nuclear grout. Magnesium potassium phosphate cements (MKPC) were investigated to determine their efficacy towards retardation of reactive uranium metal corrosion. Optimised low-water content, fly ash (FA) and blast furnace slag (BFS) blended MKPC formulations were developed and their fluidity, hydration behaviour, strength and phase assemblage investigated. In-situ time resolved synchrotron powder X-ray diffraction was used to detail the early age (~60 h) phase assemblage development and hydration kinetics, where the inclusion of BFS was observed to delay the formation of struvite-K by ~14 h compared to FA addition (~2 h). All samples set within this period, suggesting the possible formation of a poorly crystalline binding phase prior to struvite-K crystallisation. Long-term corrosion trials using metallic uranium indicated that MKPC systems are capable of limiting uranium corrosion rates (reduced by half), when compared to a UK nuclear industry grout, which highlights their potential application radioactive waste immobilisation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Strategies for control and mitigation of efflorescence in metakaolin-based geopolymers

Efflorescence can be harmful to material performance as a consequence of microstructural changes due to leaching and carbonation of alkalis. This article identifies mechanisms of efflorescence in metakaolin-based geopolymers, and approaches to reduce free/mobile alkali cations and pore network connectivity, and hence reduce efflorescence. Mechanical, mass transport and microstructural properties are assessed in metakaolin-based geopolymer cements produced using different alkali concentrations in the alkali activator and substitution/addition of blast furnace slag, silica fume, calcium aluminate cement, silicone oil and a dispersive admixture. The most effective strategy to reduce efflorescence results from increasing Si/Al in the geopolymer gel by addition of soluble silicate, silica fume or silicone oil. Addition of calcium aluminate cement or a dispersive admixture also reduce efflorescence, but are less effective. These results confirm that efflorescence may be reduced by controlling the amount of soluble silicates and reducing free alkali cations in geopolymers, providing enhanced performance and durability.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A time-dependent chloride diffusion model for predicting initial corrosion time of reinforced concrete with slag addition

The effect of granulated blast furnace slag (GBFS) addition on the threshold chloride concentration (TCC) for rebar corrosion was investigated. A modified diffusion model, coupled with a time-dependent effective diffusion coefficient and surface chloride concentration, was proposed to predict the chloride profile. The corrosion initiation time was estimated based on the model predictions and the measured TCC. The results indicate that adding GBFS decreases the TCC by lowering the pH value of the pore solution. The evolution of corrosion potential and current density is found to obey a 3-parameter Weibull distribution. MIP tests show that adding GBFS contributes to refinement of pore structure by decreasing the fraction of large capillary pores. The time-dependent model exhibits good predictive strength and helps understand how GBFS addition delays the corrosion initiation by retarding the chloride diffusion, though a lower TCC is obtained.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Experimental evidence for the acceleration of slag hydration in blended cements by the addition of CaCl2

Cements with high substitution rates of ground granulated blast furnace slags (GGBS) have the potential to significantly lower CO{sub 2} emissions of concrete, but their early age strength is often below those of traditional OPC cements. One way of mitigating this drawback is to use accelerating admixtures. In this study, the effect of CaCl{sub 2} additions on the hydration of blended cements was investigated by measuring compressive strength, porosity, heat release and propagation of ultrasound in blends containing 70 wt% of GGBS. The onset of formation of aluminate phases was monitored using in-situ XRD. The effect of CaCl{sub 2} on slag hydration was isolated by replacing GGBS by an inert quartz filler. Results showed that compressive strength values at one, two and seven days were increased by 50% by the CaCl{sub 2} addition. The increases in compressive strength corresponded to a reduction in pore space. GGBS hydration contributed to the heat development, structuration and compressive strength of the blended cements from 15 h. The addition of CaCl{sub 2} led to an earlier onset of the GGBS reaction, at around 10 h, and increased the rate of GGBS hydration during the first seven days. The time of onset of the GGBS contribution was also the moment when AFm precipitation started. In CaCl{sub 2}-containing blends, Cl was incorporated in AFm.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Influence of supplementary cementitious materials on microstructure and transport properties of spacer-concrete interface

Reinforcement spacers are a critical component of concrete structures. Their presence affects microstructure and transport properties of concrete cover though this is not widely appreciated. This paper presents the first study to determine whether the negative effects of spacers can be mitigated through the use of supplementary cementitious materials such as silica fume, fly ash and blast-furnace slag. Concrete samples (>200) with different spacers, binders, curing and drying regimes were prepared and tested for diffusion, permeation, absorption, electrical conductivity, carbonation and microstructure. It was found that spacers increase all transport properties, the extent depending on type of spacer, drying regime and transport mechanism. The spacer-concrete interface is weak, porous and micro-cracked, and this lowers the resistance of concrete to ingress of aggressive agents. The beneficial effects of SCMs (strength enhancement and densification) and prolonged curing (120-day) are insufficient to overcome the negative effects of spacers. Implications for durability are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Computational studies of impurity migration during induction stirring of molten uranium

Understanding and controlling impurity behavior in actinide metal casting processes are foundational for efficient part production yet remain major challenges for researchers and industry. To help provide insight regarding impurity distribution during actinide metal casting, we have developed computational fluid dynamics (CFD) models for a laboratory-scale system using commercial and open-source code. Multiple simulation frameworks allow for improved confidence in the resulting outputs, while taking advantage of the maturity and convenience offered by commercial platforms and simultaneously maintaining the transparency and flexibility often provided by open-source software. Here, we describe multiple experiment-informed models designed to simulate a specific laboratory system in which uranium melt, containing a known starting concentration of carbon impurity, is electromagnetically stirred in an induction furnace. Here, the goal of the simulations is to predict the motion of uranium carbide microparticles in the velocity field of the melt. Prior to simulating the uranium-carbon system, numerical models were validated using a previously published nonradioactive experimental system. Effects of the size and shape of impurity particles in the models were investigated and agree with experimental findings. Simulation of smaller particles (< 50 µm) shows more homogenous distribution throughout the stirred melt. With increased particle size (100 µm), the body forces, which include the buoyancy force, dominate over the drag force, causing larger particles to move toward the crucible walls and upward in the system.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Landfilled coal ash for carbon dioxide capture and its potential as a geopolymer binder for hazardous waste remediation

In this report, the legacy of global fossil fuel usage is not just the increase in global warming due to CO 2 production, but also the billions of tons of toxic coal ash disposed in landfills. This investigation evaluates the merits of using high-calcium landfilled coal fly ash of different disposal durations and granulated blast furnace (GBF) slag as primary raw materials for production of a new class of geopolymer binder. Processing of landfilled coal fly ash, GBF slag and supplementary raw materials into a geopolymer binder was accomplished by a simple, scalable milling process in the absence of heating under a carbon dioxide environment. The resultant geopolymer cement binders were tested for carbon dioxide uptake, compressive strength, and heavy metal stabilization. The geopolymer binder demonstrated a desired balance of carbon dioxide uptake, strength and safety. These results also indicate that the performance of the geopolymer binder depends on the landfill disposal age of the coal fly ash.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2025

In situ high-temperature Raman spectroscopy for online EAF slag analysis

Real-time monitoring of slag chemistry is critical for optimizing Electric Arc Furnace (EAF) steelmaking operations, where dynamic variations in slag composition directly influence slag foaming, refractory degradation, and thermal efficiency. Conventional techniques such as X-ray fluorescence (XRF), Fourier-transform infrared (FTIR), and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDS) are commonly used to analyze slag composition, but their offline nature and equipment constraints limit their applicability for online monitoring in harsh industrial environments. To address this challenge, we present an in situ, high-temperature analytical approach that integrates Raman spectroscopy with a custom designed fiber-optic probe for real-time slag characterization at 1550 °C. The system enables non destructive spectral acquisition from molten slags, providing molecular-level insights into silicate polymerization and iron oxidation states. Eight synthetic slag samples were evaluated, and key Raman features—such as Q n silicate units and FeO₄/FeO₆ coordination environments—were identified and quantitatively correlated with slag basicity and Fe₂O₃ content. The results demonstrate agreement between Raman spectral ratios and bulk slag chemistry, validating the method’s capability to track compositional and structural changes under molten temperature. This work establishes the feasibility of deploying fiber-optic Raman probe for online EAF slag monitoring and highlights their potential to support closed-loop control strategies, thereby enhancing process stability, refractory protection, and steel quality in industrial steelmaking applications.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Durability of plasma sprayed Thermal Barrier Coatings with controlled properties part Ⅱ: Effects of geometrical curvature

The present investigation elucidates the effects of substrate curvature on the durability of Air Plasma Sprayed (APS) Thermal Barrier Coatings (TBCs). Traditionally, planar disk specimens are utilized in Furnace Cycle Testing (FCT). In most cases, delamination is initiated at the disk's free edge and then propagates along the TBC-bond coat interface. However, in turbine components (e.g., blades/vanes), they lack significant free edges and the coatings are deposited on non-flat surfaces of varying radii of curvature. These geometrical discrepancies imply significant differences in the stress states as compared to planar disk specimens. Therefore, the part geometry inevitably affects the TBC failure mechanisms in the turbine system, and consequently influences TBC durability. Nevertheless, these effects have not been fully explored in the past, despite the anecdotal knowledge which suggests the leading edge of turbine blades to be one of the most common failure/spallation locations. Here in this study, representative TBC systems were deposited onto superalloy disks with flat substrate and rods with curved substrate. The experimental results from FCT suggest TBC durability on rods is significantly lower than when sprayed on disks. Furthermore, the durability of TBCs on rods appears to increase with higher porosity, which is contradictory to reported trends for TBCs on disks. In addition, the effects of various bond coats are not consistent with those observed in disks. To clarify the underlying effects of curved geometries, detailed stress analyses were performed. They revealed a state of thermal stresses which is unique to curved geometries. It was found that TBC on rods experience tensile radial stresses as well as tensile hoop stresses during the cooling. These stresses result in a complex interplay in failure processes in rods, which explains the different observed trends in the durability from those obtained with disks.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermal shock resistance of multilayer silicon carbide receiver tubes for 800°C molten salt concentrating solar power application

CSP power tower receiver systems during rapid transient weather periods can be vulnerable to thermal shock conditions from rain that which can facilitate the onset of leaks and failures that can have catastrophic consequences. Silicon carbide (SiC) materials have attractive receiver application characteristics for being light weight, having high-strength and excellent thermal shock resistance performance which make them a particularly good fit for receiver absorber materials in CSP. In this investigation, the performance characteristics of Ceramic Tubular Products (CTP) SiC ceramic matrix composite (CMC), multilayered tubes were explored with respect to thermal shock performance for solar receiver applications in next generation CSP plants. Here, thermal shock testing was performed at the Sandia National Laboratories (SNL) Solar Furnace facility using a dynamic stage and thermal shock tube test setup. The tubes tested under incident solar heat flux of 100 W/cm2 were heated with inner tube temperatures reaching approximately 800 °C, with outer temperatures exceeding or just reaching 1000 El for the multilayer and monolithic SiC tubes respectively. The tubes were then quenched with simulated rain. The tubes were then cooled and subjected to hoop stress analysis using an Instron device to assess their subsequent mechanical strength. Furthermore, the on-sun study experimental results indicate an average of 24.2% and 97% higher hoop strength for the CMC tubes than those composed of monolithic SiC and aluminum oxide (A1203) respectively.

14 SOLAR ENERGY↗
DOE OSTI2020

Diffuser Braze Development

At the request of SRTE, through the PDRD project, SRNL is developing a vacuum brazing process to facilitate the fabrication of hydrogen purification systems. In particular, this effort is directed at tube-style hydrogen diffusers. The diffusers are comprised of numerous palladium-silver tubes that are brazed to a nickel fitting, which is subsequently welded to a stainless steel tube, fitting, or tube sheet. Historically, torch brazing has been used as a heat source; for this work vacuum furnace brazing was suggested to improve the uniformity of the process. This report describes the braze process development for braze selection and simple nickel fitting to tube brazing. Five braze alloys were selected and sessile drop testing was conducted over a range of temperatures from 25 to 75° C over the liquidus temperature. Samples were characterized for wetting angle, erosion, and brazability. The cup-to-tube braze joints were inspected using digital radiography, ultrasonic testing, and metallographic examination. Two of the five alloys exhibited excellent fabrication properties and are considered for further development.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Maximizing Scrap Recycling by Designing Cu Tolerant Steel Compositions

Residual elements from scrap steel recycling, most notably copper, are known to result in hot shortness during thermomechanical processing and casting. As the concentration of copper and other residuals in steel scrap streams increases, Electric Arc Furnace (EAF) scrap recycling heats commonly use pig iron to dilute residuals below current limits. This work focuses on establishing residual element tolerant compositions and concomitant processing windows that can simultaneously mitigate issues from residuals during thermomechanical processing and, if possible, use these residuals to improve properties, yielding a more sustainable steel manufacturing pathway with a substantially smaller carbon footprint.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Thermal Performance of Neutron Sensor Qualification Device

The neutron sensor qualification device was developed to provide a temperature-controlled environment for neutron sensors and dosimetry, enabling irradiation in a neutron field at the Armed Forces Radiobiology Research Institute (AFRRI) TRIGA reactor facility. The device, constructed from low-activation and low neutron cross-section materials, features a modular tube furnace design with three independently controlled heating zones for controlling axial temperature distribution. Laboratory testing validated the device's thermal performance, including uniform temperature distribution with less than 6°C variation across the central region, a steady-state operational temperature of 350°C achieved in approximately 3 hours, and a cooling time constant of 3.5 hours. External surface temperatures remained safe for handling, with the surrounding aluminum structure remaining at ambient conditions. The results confirm the device’s suitability for neutron sensor qualification experiments, with potential for future operation at higher temperatures and further optimization of performance.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2021

Consumer Guide to Home Heating and Cooling

Learn about types of heating and cooling systems, system maintenance, and best practices for saving energy with your heating and cooling. This fact sheet from Energy Saver also includes information on buying a new heating or cooling system; efficiency ratings; and selecting new systems including air conditioners, heat pumps, and furnaces.

heating, cooling, air conditioners, heat pumps, fu↗
DOE OSTI2022

CSP Optical Facilities at the National Renewable Energy Laboratory

The concentrating Solar Power (CSP) Optical Facilities at NREL comprise unique optical tools and facilities for testing and characterizing concentrating solar optical components. These facilities are maintained to aid researchers and industry efforts to reduce market barriers, improve the performance, reduce the cost, and improve the lifetime and reliability of CSP materials, components, subsystems, and integrated concepts, where accurate and timely characterization methods are needed. To reach this goal, NREL is committed to collaborating in ongoing and projected research needs for industry, academia, and government entities, in the development and characterization of low-cost, high-performance reflector and absorber materials in addition to their components-a key element in the conversion of concentrated sunlight into energy. To accomplish this mission, the core laboratory includes the Advanced Optical Materials Laboratory, indoor and outdoor accelerated weather testing tools, "Distant Observer" for parabolic troughs, the High Flux Solar Furnace, and the ultra-accelerated weather testing tools. This equipment enables to rapidly respond to new challenges with novel solutions that align with the goals of the Solar Energy Technology Office (SETO) at the U.S. Department of Energy. The goal of this paper is to present the state-of art-optical facilities available at NREL that can help support the research needs of the CSP community. Therefore, we review here the different components of the CSP Optical Facilities at NREL and highlight their characteristics and importance for the CSP community.

accelerated weather testing↗
DOE OSTI2024

Circular Economy Contributions to Decarbonizing the US Steel Sector

The potential benefits of the circular economy (CE) for decarbonization have recently attracted much attention in the academic and grey literature. The department of energy (DOE) industrial decarbonization roadmap highlight that in addition to the four pillars (energy efficiency, electrification, low-carbon fuels, feedstocks, and energy sources, and carbon capture, utilization, and storage (CCUS)) identified in the roadmap, "scenarios [...] will need to be developed that incorporate materials efficiency and circular economy strategies". Moreover, the roadmap identifies hard-to-abate CO2 emissions across the five industrial subsectors included in the analysis (iron & steel, chemical, food & beverage, refining, and cement manufacturing). Thus, additional options to decarbonize the industrial sector, like the CE, could prove beneficial to address those hard-to-abate emissions. Moreover, they may be less costly, require less R&D or incentives, and be more readily adopted than other strategies such as energy efficiency and CCUS. While the Industrial Decarbonization Roadmap includes some CE strategies (e.g., the increasing market share of steel from electric arc furnaces - which incorporate steel scrap), a deeper dive into what role the CE could play in the United States (US) industrial decarbonization is needed. In this work, we present several industrial decarbonization scenarios that incorporate materials efficiency and circular economy strategies for the iron & steel subsector. The scenarios identify barriers (including technical limits and constraints), opportunities, and R&D needs.Moreover, we estimate the contribution of those scenarios to reducing the industrial sector's CO2 emissions and their potential synergies with the Industrial Decarbonization Roadmap's four pillars. Iron & steel manufacturing was responsible for 90 million tons of industrial CO2 emissions in 2020 - 7% of the industrial sector's total process- related emissions. Besides recycling - which presents technical limitations due to trace contaminants - CE strategies on the demand side could lower iron & steel manufacturing emissions (e.g., the development of lighter products or business models that encourage a more intensive use). This study reviews barriers, opportunities, and trade-offs for 5 material efficiency strategies. Many topics explored in the review call for further research.

barriers↗
DOE OSTI2023

Ultra‐Low‐Loss Silicon Nitride Photonics Based on Deposited Films Compatible with Foundries

Abstract The fabrication processes of silicon nitride (Si 3 N 4 ) photonic devices used in foundries require low temperature deposition, which typically leads to high propagation losses. Here, it is shown that propagation loss as low as 0.42 dB cm −1 can be achieved using foundry compatible processes by solely reducing waveguide surface roughness. By postprocessing the fabricated devices using rapid thermal anneal (RTA) and furnace anneal, propagation losses down to 0.28 dB cm −1 and 0.06 dB cm −1 , respectively, are achieved. These low losses are comparable to the conventional devices using high temperature, high‐stress LPCVD films. The dispersion of the devices is also tuned, and it is proved that these devices can be used for linear and nonlinear applications. Low threshold parametric oscillation, broadband frequency combs, and narrow‐linewidth laser are demonstrated. This work demonstrates the feasibility of scalable photonic systems based on foundries.

Ji, Xingchen↗