Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Progress towards high efficiency polycrystalline thin-film GaAs AMOS solar cells

Results of Ge film recrystallization using focused laser beams and GaAs film growth on such layers in the making of high efficiency thin-film AMOS solar cells are discussed. Since a conversion efficiency of 14% was obtained for an AMOS cell fabricated on sliced bulk polycrystalline GaAs, high efficiency cells are being developed by chemically vapor-depositing GaAs films on previously recrystallized evaporated Ge films to minimize the grain boundary (GB) effects. Schottky barrier solar cells made on sliced polycrystalline GaAs wafers were studied to investigate the effects of grain boundaries on cell properties and the potential efficiency of GaAs thin-film cells. Ge film recrystallization and the chemical vapor deposition (CVD) of the 2 to 3 micron thick GaAs films are described. AMOS solar cells with 100 Angstrom thick Ag metallization were made on CVD GaAs/recrystallized Ge/W substrates with an energy conversion efficiency of 8%.

Yeh, Y. C. M.↗
NASA NTRS1985

High efficiency solar cell processing

At the time of writing, cells made by several groups are approaching 19% efficiency. General aspects of the processing required for such cells are discussed. Most processing used for high efficiency cells is derived from space-cell or concentrator cell technology, and recent advances have been obtained from improved techniques rather than from better understanding of the limiting mechanisms. Theory and modeling are fairly well developed, and adequate to guide further asymptotic increases in performance of near conventional cells. There are several competitive cell designs with promise of higher performance ( 20%) but for these designs further improvements are required. The available cell processing technology to fabricate high efficiency cells is examined.

Ho, F.↗
NASA NTRS1995

Investigation of the basic physics of high efficiency semiconductor hot carrier solar cell

The main purpose of this research program is to investigate potential semiconductor materials and their multi-band-gap MQW (multiple quantum wells) structures for high efficiency solar cells for aerospace and commercial applications. The absorption and PL (photoluminescence) spectra, the carrier dynamics, and band structures have been investigated for semiconductors of InP, GaP, GaInP, and InGaAsP/InP MQW structures, and for semiconductors of GaAs and AlGaAs by previous measurements. The barrier potential design criteria for achieving maximum energy conversion efficiency, and the resonant tunneling time as a function of barrier width in high efficiency MQW solar cell structures have also been investigated in the first two years. Based on previous carrier dynamics measurements and the time-dependent short circuit current density calculations, an InAs/InGaAs - InGaAs/GaAs - GaAs/AlGaAs MQW solar cell structure with 15 bandgaps has been designed. The absorption and PL spectra in InGaAsP/InP bulk and MQW structures were measured at room temperature and 77 K with different pump wavelength and intensity, to search for resonant states that may affect the solar cell activities. Time-resolved IR absorption for InGaAsP/InP bulk and MQW structures has been measured by femtosecond visible-pump and IR-probe absorption spectroscopy. This, with the absorption and PL measurements, will be helpful to understand the basic physics and device performance in multi-bandgap InAs/InGaAs - InGaAs/InP - InP/InGaP MQW solar cells. In particular, the lifetime of the photoexcited hot electrons is an important parameter for the device operation of InGaAsP/InP MQW solar cells working in the resonant tunneling conditions. Lastly, time evolution of the hot electron relaxation in GaAs has been measured in the temperature range of 4 K through 288 K using femtosecond pump-IR-probe absorption technique. The temperature dependence of the hot electron relaxation time in the X valley has been measured.

Alfano, R. R.↗
NASA NTRS1984

Summary of the high-efficiency crystalline solar cell research forum

An outline is given listing the speeches given in each session and the pertinent points is some speeches. There were six session, besides the overview session they were: (1) high efficiency concepts; (2) surface/interface effects; (3) bulk effects; (4) modeling; and (5) high efficiency device processing. Besides the emphasis placed on increasing efficiency of energy conversion, a great amount of discussion was spent on ways to reduce recombination and reducing surface defects.

Wolf, M.↗
DOE OSTI2020

An Optimized Fibril Network Morphology Enables High‐Efficiency and Ambient‐Stable Polymer Solar Cells

Abstract Morphological stability is crucially important for the long‐term stability of polymer solar cells (PSCs). Many high‐efficiency PSCs suffer from metastable morphology, resulting in severe device degradation. Here, a series of copolymers is developed by manipulating the content of chlorinated benzodithiophene‐4,8‐dione (T1‐Cl) via a random copolymerization approach. It is found that all the copolymers can self‐assemble into a fibril nanostructure in films. By altering the T1‐Cl content, the polymer crystallinity and fibril width can be effectively controlled. When blended with several nonfullerene acceptors, such as TTPTT‐4F, O‐INIC3, EH‐INIC3, and Y6, the optimized fibril interpenetrating morphology can not only favor charge transport, but also inhibit the unfavorable molecular diffusion and aggregation in active layers, leading to excellent morphological stability. The work demonstrates the importance of optimization of fibril network morphology in realizing high‐efficiency and ambient‐stable PSCs, and also provides new insights into the effect of chemical structure on the fibril network morphology and photovoltaic performance of PSCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2000

A High-Efficiency Refractive Secondary Solar Concentrator for High Temperature Solar Thermal Applications

A refractive secondary solar concentrator is a non-imaging optical device that accepts focused solar energy from a primary concentrator and redirects that light, by means of refraction and total internal reflection (TIR) into a cavity where the solar energy is used for power and/or propulsion applications. This concept offers a variety of advantages compared to typical reflective secondary concentrators (or the use of no secondary at all): higher optical efficiency, minimal secondary cooling requirements, a smaller cavity aperture, a reduction of outgassing from the cavity and flux tailoring of the solar energy within the heat receiver. During the past 2 years, NASA Lewis has been aggressively developing this concept in support of the NASA Marshall Shooting Star Flight Experiment. This paper provides a brief overview of the advantages and technical challenges associated with the development of a refractive secondary concentrator and the fabrication of a working unit in support of the flight demonstration program.

Piszczor, Michael F., Jr.↗
NASA NTRS1986

Development of high-efficiency solar cells on silicon web

Work was performed to improve web base material with a goal of obtaining solar cell efficiencies in excess of 18% (AM1). Efforts in this program are directed toward identifying carrier loss mechanisms in web silicon, eliminating or reducing these mechanisms, designing a high efficiency cell structure with the aid of numerical models, and fabricating high efficiency web solar cells. Fabrication techniques must preserve or enhance carrier lifetime in the bulk of the cell and minimize recombination of carriers at the external surfaces. Three completed cells were viewed by cross-sectional transmission electron microscopy (TEM) in order to investigate further the relation between structural defects and electrical performance of web cells. Consistent with past TEM examinations, the cell with the highest efficiency (15.0%) had no dislocations but did have 11 twin planes.

Meier, D. L.↗
NASA NTRS1982

High-Efficiency Solar Cells on Low-Cost Substrates

High-efficiency solar cells made in thin epitaxial films grown on low-cost commercial silicon substrates. Cost of cells is much less than if high-quality single-crystal silicon were used for substrates and performance of cells is almost as good.

Daiello, R. V.↗
NASA NTRS1975

ALARM: A highly efficient eigenvalue extraction routine for very large matrixes

A highly efficient computer program, called ALARM, for the determination of eigenvalues and eigenvectors of large symmetric matrices (over 10,000 degrees of freedom), was described. As such, it is highly useful for analyzing complex finite element and finite difference idealizations encountered in structural dynamics and acoustic probelms. The program is based upon a scheme which reduces a large matrix to an equivalent tridiagonal one of much smaller size. The main strength of the algorithm lies in its ability to retain all the information required to obtain the eigenvalues at either end of the original matrix spectrum.

Ojalvo, I. U.↗
NASA NTRS1984

High-efficiency silicon solar cells

Silicon solar cells are described which operate at energy conversion efficiencies independently measured at 18.7 percent under standard terrestrial test conditions (AM1.5, 100 mW/sq cm, 28 C). These are apparently the most efficient silicon cells fabricated to date. The high-efficiency results from a combination of high open-circuit voltage due to the careful attention paid to the passivation of the top surface of the cell, high fill factor due to the high open-circuit voltage and low parasitic resistance losses, and high short-circuit current density due to the use of shallow diffusions, a low grid coverage, and an optimized double layer antireflection coating.

Green, M. A.↗
NASA NTRS1979

The potential of np GaAs solar cells for high efficiency concentrator applications

This communication considers the design of the front grid contact of np GaAs solar cells for high efficiency concentrator applications. This design involves shadowing, contact resistance, and active layer sheet resistance losses, and at high concentrations, the power loss due to voltage drop on the resistance of the grid fingers should be considered. Analysis of the performance can be calculated as a function of junction depth and surface recombination velocity. The junction depth can be optimized by considering its effect on the collection efficiency of the dark current-voltage characteristics or the open circuit voltage, and on the series resistance loss or the fill factor for material parameters. The choice of the material parameters, calculation of the short circuit current, the selection of the n layer thickness, and the cell maximum power and efficiency are discussed. It is concluded that optimized multi-grid structures should allow the use of 10 by 10 sq cm cells with good efficiencies at high concentration ratios, and efficiencies of 22 to 25% should be obtainable from large area cells at concentrations of 40 AM1.

Flat, A.↗
DOE OSTI2022

Solid additive engineering enables high-efficiency and eco-friendly all-polymer solar cells

Currently, morphology optimization of all-polymer solar cells (all-PSCs) strongly depends on the use of solvent additives, which are usually highly toxic and harmful to the environment and human health. Here, we report a green and volatile solid additive, 2-methoxynaphthalene (2-MN). It was found that the incorporation of 2-MN into a PM6:PY-DT blend can effectively manipulate the aggregations of PM6 and PY-DT during film depositing and thermal annealing processes and results in highly ordered molecular packing and favorable phase-separated morphology. Consequently, a record-high efficiency of 17.32% is achieved for the PM6:PY-DT device. Moreover, 2-MN-processed all-PSCs were fabricated by using non-halogenated solvent. High efficiencies of 17.03% and 16.67% are obtained for all-PSCs fabricated under nitrogen atmosphere and ambient conditions, respectively. Finally, our work shows that the utilization of 2-MN as a green and solid additive is a simple and feasible strategy to optimize the morphology and sheds new light on eco-friendly fabrication and application of all-PSCs.

14 SOLAR ENERGY↗
NASA NTRS1991

High efficiency Ka-band MMIC amplifiers

This paper describes recent progress in the Ka-band MMIC power amplifier program. New materials, material growth techniques, device designs and circuit design techniques have made it possible to design and fabricate MMIC amplifiers with both high efficiency and high power at Ka-band and higher frequencies. MMIC amplifiers using pseudomorphic AlGaAs/InGaAs/GaAs HEMT devices presently achieve 400 mW with 25 percent efficiency at Ka-band and 1 W, 35 percent efficient amplifiers are being developed.

Haugland, Edward J.↗
DOE OSTI2020

High Efficiency 6-Junction Solar Cells for the Global and Direct Spectra

We show 6-junction inverted metamorphic solar cells with high efficiencies under both the global and direct spectrum, and discuss improvements to device components. High voltage AlGaInP subcells are demonstrated on GaAs substrates miscut 2° towards (111)B by using Sb surfactant to reduce atomic ordering. This miscut enables high voltage and low dislocation density GaInAs subcells by using atomically-ordered GaInP-based graded buffers. One-sun efficiencies of 39.2 ± 1.3% under the global spectrum and 39.4 ± 1.1% direct spectrum have been demonstrated by using these high voltage subcell components. For high efficiency under the concentrated direct spectrum, low resistance is also necessary, which requires a challenging and nonintuitive optimization of tunnel junctions and heterobarriers. Increasing the thickness of a (Al)GaInAs spacer layer between the back surface fields (BSF) and tunnel junctions (TJ) of latticemismatched subcells reduces nonlinear resistance, which implies a detrimental interaction between the BSF and TJ. Concentrator devices with optimized spacer layers show reduced effective resistance and maintain fill factor > 75% at 1100 suns. Device efficiencies under the concentrated direct spectrum peak at 47.1 ± 3.2% at 143 suns.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2020

Optimization of multiplexed CRISPR/Cas9 system for highly efficient genome editing in Setaria viridis

Previously, Setaria viridis has been developed as a model plant to better understand the C4 photosynthetic pathway in major crops. With the increasing availability of genomic resources for S. viridis research, highly efficient genome editing technologies are needed to create genetic variation resources for functional genomics. In this paper, we developed a protoplast assay to rapidly optimize the multiplexed CRISPR/Cas9 system in S. viridis. Targeted mutagenesis efficiency was further improved by an average of 1.4-fold with the exonuclease, Trex2. Distinctive mutation profiles were found in the Cas9_Trex2 samples with 94% of deletions larger than 10bp, and less than 1% of mutations being insertions. Further analyses indicated that 52.2% of deletions induced by Cas9_Trex2, as opposed to 3.5% by Cas9 alone, were repaired through microhomology-mediated end joining (MMEJ) rather than the canonical NHEJ DNA repair pathway. Combined with the robust agrobacterium-mediated transformation method with more than 90% efficiency, the multiplex CRISPR/Cas9_Trex2 system was demonstrated to induce targeted mutations in two tightly linked genes, svDrm1a and svDrm1b, at the frequency ranging from 73% to 100% in T0 plants. These mutations were transmitted to at least 60% of the transgene-free T1 plants with 33% of them containing bi-allelic or homozygous mutations in both genes. This highly efficient multiplex CRISPR/Cas9_Trex2 system makes it possible to create a large mutant resource for S. viridis in a rapid and high throughput manner, and has the potential to be widely applicable in achieving more predictable MMEJ-mediated mutations in many plant species.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1980

High efficiency ultrathin coplanar back contact cells

Efforts to fabricate high efficiency, ultrathin coplanar back contact cells are described. Included is a description of design considerations, cell fabrication, and theoretical and experimental analyses of loss mechanisms. The results of these efforts has been the fabrication of a 11.8% AM0 efficient, 50 micron cell when measured at 25 C. Design and process changes required to increase the efficiency are indicated.

Storti, G.↗
NASA NTRS1984

High-efficiency crystalline silicon technology development

The rationale for pursuing high efficiency crystalline silicon technology research is discussed. Photovoltaic energy systems are reviewed as to their cost effectiveness and their competitiveness with other energy systems. The parameters of energy system life are listed and briefly reviewed.

Prince, M. B.↗