Results for “data base for model validation” — Page 11

NASA NTRS2022

Investigating Particle-Particle Electrostatic Effects on Charged Lunar Dust Transport via Discrete Element Modeling

NASA surface exploration missions have always seen negative effects of dust including the Apollo missions. The astronaut-witnessed unusual behavior of the dust particles that surround the vehicle after engine cutoff has the potential to have more of an influence on surface systems dust loading than the high velocity lunar rocket plume ejecta in the landing process. The levitation and transport of the fine components of regolith on lunar surface has been linked to electrostatic effects and electric field, but so far there is no accurate model considering the inter-particle electrostatic interactions, especially when the particles are charged by rocket plume or other mechanical interactions due to exploration activities. This study is proposed to investigate the dynamics of charged lunar regolith with a discrete element method (DEM) approach focusing on the inter-particle interactions and contact charge transfer. The grain dynamics is coupled with mechanical and electrical particle interactions, and both short- and long-range interactions between spherical particles are incorporated. A tribo-charging model based on instantaneous collisions between particles is adopted and validated by comparing the simulation results to existing experimental data. Sensitivity analysis is conducted to quantify the effects of initial charge, tribo-charging, and E-field on transport of lunar dust based on JSC-1 simulants with a radius of 50 lm. DEM simulations are also conducted in a near realistic lunar environment with the estimations of initial conditions that shows the difference in position and velocity distributions between charged particles and uncharged particles. The results indicate that the charged dust particles have higher dispersion of position and velocity by several orders of magnitude due to electrostatic effects. This provides a potential explanation for the phenomena of the approximately 30 s dust lofting following Apollo Lunar Module landing.

Lunar dust↗

NASA NTRS2012

The Invasive Species Forecasting System (ISFS): An iRODS-Based, Cloud-Enabled Decision Support System for Invasive Species Habitat Suitability Modeling

The Invasive Species Forecasting System (ISFS) is an online decision support system that allows users to load point occurrence field sample data for a plant species of interest and quickly generate habitat suitability maps for geographic regions of interest, such as a national park, monument, forest, or refuge. Target customers for ISFS are natural resource managers and decision makers who have a need for scientifically valid, model- based predictions of the habitat suitability of plant species of management concern. In a joint project involving NASA and the Maryland Department of Natural Resources, ISFS has been used to model the potential distribution of Wavyleaf Basketgrass in Maryland's Chesapeake Bay Watershed. Maximum entropy techniques are used to generate predictive maps using predictor datasets derived from remotely sensed data and climate simulation outputs. The workflow to run a model is implemented in an iRODS microservice using a custom ISFS file driver that clips and re-projects data to geographic regions of interest, then shells out to perform MaxEnt processing on the input data. When the model completes, all output files and maps from the model run are registered in iRODS and made accessible to the user. The ISFS user interface is a web browser that uses the iRODS PHP client to interact with the ISFS/iRODS- server. ISFS is designed to reside in a VMware virtual machine running SLES 11 and iRODS 3.0. The ISFS virtual machine is hosted in a VMware vSphere private cloud infrastructure to deliver the online service.

Gill, Roger↗

NASA NTRS1978

Directional models for analysis of earth radiation budget measurements

The determination of the radiation heat flux densities at the top of the atmosphere (30 km) for spatial scales ranging from global to regional is necessary for the conversion of satellite irradiance measurements into useful earth radiation budget information. Data reduction algorithms are required which contain assumed directional characteristics of radiation emitted and scattered from the earth-atmosphere system. The directional characteristics are defined by models which express, for a given surface element at the top of the atmosphere, the exiting flux per unit solid angle for each direction out to space as a fraction of the total hemispheric flux exiting the surface element. Both longwave and shortwave directional radiation models are analyzed. It is found that the validity of the Nimbus 2-based limb darkening curves has generally been verified for the longwave data with the exception of the Antarctic snow fields where limb brightening was noticed in the earth radiation budget data.

Suttles, J. T.↗

NASA NTRS1972

A critical examination of the validity of simplified models for radiant heat transfer analysis.

Examination of the directional effects of the simplified models by comparing the experimental data with the predictions based on simple and more detailed models for the radiation characteristics of surfaces. Analytical results indicate that the constant property diffuse and specular models do not yield the upper and lower bounds on local radiant heat flux. In general, the constant property specular analysis yields higher values of irradiation than the constant property diffuse analysis. A diffuse surface in the enclosure appears to destroy the effect of specularity of the other surfaces. Semigray and gray analyses predict the irradiation reasonably well provided that the directional properties and the specularity of the surfaces are taken into account. The uniform and nonuniform radiosity diffuse models are in satisfactory agreement with each other.

Toor, J. S.↗

NASA NTRS2023

Modeling and Simulation of the Angel Upper Limb Offload Device: Branching Into New Methods

BACKGROUND: The Active Response Gravity Offload System (ARGOS) provides an analog environment for extravehicular activity (EVA) testing and training. Discomfort has been observed during longer suited test sessions. While the subject’s core is offloaded during surface EVA evaluations, his/her arms experience full Earth gravity and can become overly fatigued, especially during suited tests which involve reaching and prolonged arm extensions. A device (ARGOS Negation of Gravitational Effects on the Limbs: ANGEL) to offload the weight of the arms and suit sleeves is being developed by JSC’s Flight Systems Branch of the Software, Robotics, and Simulation Division. Previously we have shared preliminary modeling of that device and kinematics based on motion capture data. Here we present an alternative approach to determine device kinematics by calculating ANGEL component angles with an OpenSim plugin. We compare calculated angles to inverse kinematics (IK) derived ones with the goal of validating the model. This new method can be further informative for device design and analytically testing different configurations to achieve desired reduced gravity conditions (e.g., lunar gravity (Lg) or Martian gravity (Mg)). We have compared calculated angles with IK-derived angles in tests with a shirt-sleeve subject positioned in a test stand with a Mark-III Hard Upper Torso (HUT) and Portable Life Support System (PLSS) mockup and arm weights to emulate the weight of the suit sleeve as well as a suited subject in ARGOS with a Mark-III suit. A variety of upper body tasks were completed in the former and full-body tasks in the latter. METHODS AND RESULTS: To model the offload device, we augment the OpenSim human model topology with the offload mechanism components and joints, using CAD models to represent the mechanism graphically. The joint angles of the device are calculated in the OpenSim plugin by modeling how the components configure themselves under the offloading spring tension given a particular IK-derived arm position. There are four ANGEL components with a total of 5 degrees of freedom (DOFs), each component has a single DOF except for the cuff which is modeled as 2 DOFs. The sickle/yaw bracket and cuff rotation angles are determined statically based on the assumptions that the sickle will track the attachment point of the cuff and that the cuff will rotate such that the attachment point is at its highest point. The cuff tilt, linker and V-bracket angles are then determined by optimizing their positions to approach a mechanical equilibrium. The calculated linker angle is compared to three different methods of determining the linker line-of-force kinematically (from V-bracket to center-cuff, cuff highest point or marker-derived position). Given the joint angles of the device, the spring force and resulting force on the arm is computed by the plugin and applied as an external load in inverse dynamics (ID) to enable study of overall shoulder joint torques as well as offload achieved. We verify the calculated joint angles by using the inverse kinematic data. The average difference in angles is the smallest for the V-bracket and linker, around 1 to 5 degrees for most trials. The resulting offload and shoulder torque are comparable between calculated and IK-derived angles. In summary, we have developed a method to calculate the joint angles of an exoskeleton-like upper limb offloading device currently in development. We have also developed a custom plugin which will be a valuable tool to optimize device configurations for a desired gravitational environment, probe the offload achieved for motions recorded outside of our test suite, and inform future design improvements.

L B Nilsson↗

NASA NTRS2023

Modeling and Simulation of The Angel Upper Limb Offload Device: Branching into New Methods

BACKGROUND: The Active Response Gravity Offload System (ARGOS) provides an analog environment for extravehicular activity (EVA) testing and training. Discomfort has been observed during longer suited test sessions. While the subject’s core is offloaded during surface EVA evaluations, his/her arms experience full Earth gravity and can become overly fatigued, especially during suited tests which involve reaching and prolonged arm extensions. A device (ARGOS Negation of Gravitational Effects on the Limbs: ANGEL) to offload the weight of the arms and suit sleeves is being developed by JSC’s Flight Systems Branch of the Software, Robotics, and Simulation Division. Previously we have shared preliminary modeling of that device and kinematics based on motion capture data. Here we present an alternative approach to determine device kinematics by calculating ANGEL component angles with an OpenSim plugin. We compare calculated angles to inverse kinematics (IK) derived ones with the goal of validating the model. This new method can be further informative for device design and analytically testing different configurations to achieve desired reduced gravity conditions (e.g., lunar gravity (Lg) or Martian gravity (Mg)). We have compared calculated angles with IK-derived angles in tests with a shirt-sleeve subject positioned in a test stand with a Mark-III Hard Upper Torso (HUT) and Portable Life Support System (PLSS) mockup and arm weights to emulate the weight of the suit sleeve as well as a suited subject in ARGOS with a Mark-III suit. A variety of upper body tasks were completed in the former and full-body tasks in the latter. METHODS AND RESULTS: To model the offload device, we augment the OpenSim human model topology with the offload mechanism components and joints, using CAD models to represent the mechanism graphically. The joint angles of the device are calculated in the OpenSim plugin by modeling how the components configure themselves under the offloading spring tension given a particular IK-derived arm position. There are four ANGEL components with a total of 5 degrees of freedom (DOFs), each component has a single DOF except for the cuff which is modeled as 2 DOFs. The sickle/yaw bracket and cuff rotation angles are determined statically based on the assumptions that the sickle will track the attachment point of the cuff and that the cuff will rotate such that the attachment point is at its highest point. The cuff tilt, linker and V-bracket angles are then determined by optimizing their positions to approach a mechanical equilibrium. The calculated linker angle is compared to three different methods of determining the linker line-of-force kinematically (from V-bracket to center-cuff, cuff highest point or marker-derived position). Given the joint angles of the device, the spring force and resulting force on the arm is computed by the plugin and applied as an external load in inverse dynamics (ID) to enable study of overall shoulder joint torques as well as offload achieved. We verify the calculated joint angles by using the inverse kinematic data. The average difference in angles is the smallest for the V-bracket and linker, around 1 to 5 degrees for most trials. The resulting offload and shoulder torque are comparable between calculated and IK-derived angles. In summary, we have developed a method to calculate the joint angles of an exoskeleton-like upper limb offloading device currently in development. We have also developed a custom plugin which will be a valuable tool to optimize device configurations for a desired gravitational environment, probe the offload achieved for motions recorded outside of our test suite, and inform future design improvements.

L B Nilsson↗

NASA NTRS1994

A supercritical airfoil experiment

The purpose of this investigation is to provide a comprehensive data base for the validation of numerical simulations. The initial results of the study (single angle of attack) were presented in ref. 1, where the effects of various parameters and the adequacies of selected turbulence models were discussed. The objective of the present paper is to provide a tabulation of the experimental data. The data were obtained in the two-dimensional, transonic flowfield surrounding a supercritical airfoil. A variety of flows were studied in which the boundary layer at the trailing edge of the model was either attached or separated. Unsteady flows were avoided by controlling the Mach number and angle of attack. Surface pressures were measured on both the model and wind tunnel walls, and the flowfield surrounding the model was documented using a laser Doppler velocimeter (LDV). Although wall interference could not be completely eliminated, its effect was minimized by employing the following techniques. Sidewall boundary layers were reduced by aspiration, and upper and lower walls were contoured to accommodate the flow around the model and the boundary-layer growth on the tunnel walls. A data base with minimal interference from a tunnel with solid walls provides an ideal basis for evaluating the development of codes for the transonic speed range because the codes can include the wall boundary conditions more precisely than interference corrections can be made to the data sets.

Mateer, George G.↗

NASA NTRS2019

Quantifying Water Storage Change and Land Subsidence Induced by Reservoir Impoundment Using GRACE, Landsat, and GPS Data

The construction of hydropower dams is a common strategy to support a country's increasing need for electricityand river water management for industry and agriculture. Although the hydrological and geophysical impacts ofwater relocation are usually assessed prior to impoundment, their accuracy is generally limited due to the lack ofin situ observations, especially in a remote area. This study presents a workflow to quantify the terrestrial waterstorage change (TWS) and land subsidence induced by a reservoir's water impoundment using multiple satelliteobservations (GRACE, Landsat), land surface models (CABLE, GLDAS, NCEP, ECMWF), and GPS data. The studysite is the Bakun Dam, located in Sarawak, Malaysia, which is the largest hydropower dam in Southeast Asia.Commencing operation in late 2010, the dam induced a change of water mass and lake surface area that wasclearly observed by GRACE and Landsat observations, respectively. During the 17-month impounding period(from August 2010 to December 2011), GRACE observed a dramatic increase of approximately 200mmequivalent water height, while Landsat detected an increased lake extent of around 600 km2. In this paper, aforward model is developed to determine the increased water surface level corresponding to GRACE observations,estimated to be about 120 m. In contrast to GRACE, the TWS derived from land surface models cannotcapture the increased TWS, due to the lack of reservoir routing algorithms in the models. In addition, the landsubsidence was calculated using the disk load model constructed based on the GRACE-derived lake level andLandsat-derived lake extent; the result is validated with the GPS data from BIN1 station, located at the westerncoast of Borneo. The commencement stage of the Bakun Dam induces the large-scale land subsidence, whichcauses the GPS-BIN1 station to subside by ~9 mm, and move toward the Bakun Lake by ~4 mm. Computation ofthe surface displacements directly from GRACE spherical harmonic coefficient data fails to capture the subsidencefeature, mainly due to the truncation error. Overall, this study demonstrates that evaluating GRACE inconjunction with Landsat, LSMs, and GPS data allows the exploitation of the gravity signal at a much smallerspatial scale than its intrinsic resolution. Benefiting from global coverage, the newly developed satellite-basedalgorithm is a valuable tool for assessing the impacts of reservoir operation on hydrological and geophysicalchanges from local to regional scales.

Tangdamrongsub, Natthachet↗

NASA NTRSDate not supplied

In-Situ Scanning Electron Microscope Experiments for Microscale Mechanical Testing and Validated Modeling of Fiber Reinforced Thermoplastics

A novel, in-situ, scanning electron microscope (SEM) mechanical testing capability for materials at the microscale which provides experimental validation to a machine learning (ML) toolset for full-field validation of physics-based micromechanics models is being developed by researchers at NASA Glenn Research Center. These are enabling technologies for the integration of multiscale digital twins for materials into system level models which will result in the improved performance, material discovery, reduced production cost and time, rapid characterization, and prognostic structural health monitoring (SHM) for materials and structures for extreme environments in support of NASA space exploration missions. In order to bridge the material structure-to-system gap for digital twins, physics-based models must be experimentally validated at multiple length scales. Seminal microscale experiments, conducted at the Air Force Research Laboratory (AFRL), were limited to transverse compression of single-layer, unidirectional thermoset polymer matrix composite (PMC) micropillar specimens [1]. The early phases of the current project followed those initial results and setup to reproduce the compression testing of PMC material on the custom-built piezoelectric actuated micromechanical testing rig built by MicroTesting Solutions LLC. In this work, samples of thermoplastic PMC material were first machined into 3 mm cubes, and then further machining and final milling was done using a Focused Ion Beam (FIB). The initial experiment was done on a pillar roughly 20 µm x 20 µm x 40 µm tall. Additional pillars were milled with final sizes ranging from 20 µm x 20 µm x 40 µm tall to 40 µm x 40 µm x 65 µm tall. A speckle pattern for in-situ full-field measurements using Digital Image Correlation (DIC) was applied with platinum, which was coated on the surface, and then the FIB was used to mill away some of the coating to produce an irregular pattern of Pt on the pillar surface. The samples were loaded into the custom testing rig and placed into the SEM and loaded under compression until failure. Images were collected in the SEM during testing. Post-processing of the images was conducted using DIC to obtain full-field displacement and strain measurements elucidating the role of the matrix as well as fiber-fiber interaction at the microscale within the composite subjected to compression loading well into the non-linear regime of the material. Moreover, the evolution of fiber-matrix debonding and matrix cracking is observed in-situ at the microscale. This data, along with images segmented with a newly developed ML toolset [2], was used to create and validate physics-based micromechanics models. An image of the failed micropillar is shown in Figure 1. The techniques developed in the initial compression experiment was tailored to the validation needs of the models and expanded to include different sized samples as well as possibly tension and fatigue.

Laura Wilson↗

NASA NTRS2009

Integration of Dust Prediction Systems and Vegetation Phenology to Track Pollen for Asthma Alerts in Public Health

Initial efforts to develop a deterministic model for predicting and simulating pollen release and downwind concentration to study dependencies of phenology on meteorology will be discussed. The development of a real-time, rapid response pollen release and transport system as a component of the New Mexico Environmental Public Health Tracking System (EPHTS), is based on meteorological models, NASA Earth science results (ESR), and an in-situ network of phenology cameras. The plan is to detect pollen release verified using ground based atmospheric pollen sampling within a few hours using daily MODIS daa in nearly real-time from Direct Broadcast, similar to the MODIS Rapid Response System for fire detection. As MODIS winds down, the NPOESS-VIIRS sensor will assume daily vegetation monitoring tasks. Also, advancements in geostationary satellites will allow 1km vegetation indices at 15-30 minute intervals. The pollen module in EPHTS will be used to: (1) support public health decisions for asthma and allergy alerts in New Mexico, Texas and Oklahoma; (2) augment the Centers for Disease Control and Prevention (CDC)'s Environmental Public Health Tracking Network (EPHTN); and (3) extend surveillance services to local healthcare providers subscribing to the Syndrome Reporting Information System (SYRIS). Previous studies in NASA's public health applications portfolios provide the infrastructure for this effort. The team is confident that NASA and NOAA ESR data, combined into a verified and validated dust model will yield groundbreaking results using the modified dust model to transport pollen. The growing ESR/health infrastructure is based on results from a rapid prototype scoping effort for pollen detection and simulation carried out by the principal investigators.

Luvall, Jeffrey↗

NASA NTRS2014

Mars Science Laboratory (MSL) Entry, Descent, and Landing Instrumentation (MEDLI): Complete Flight Data Set

The Mars Science Laboratory (MSL) entry vehicle (EV) successfully entered the Mars atmosphere and landed the Curiosity rover safely on the surface of the planet in Gale crater on August 6, 2012. MSL carried the MSL Entry, Descent, and Landing (EDL) Instrumentation (MEDLI). MEDLI delivered the first in-depth understanding of the Mars entry environments and the response of the entry vehicle to those environments. MEDLI was comprised of three major subsystems: the Mars Entry Atmospheric Data System (MEADS), the MEDLI Integrated Sensor Plugs (MISP), and the Sensor Support Electronics (SSE). Ultimately, the entire MEDLI sensor suite consisting of both MEADS and MISP provided measurements that were used for trajectory reconstruction and engineering validation of aerodynamic, atmospheric, and thermal protection system (TPS) models in addition to Earth-based systems testing procedures. This report contains in-depth hardware descriptions, performance evaluation, and data information of the three MEDLI subsystems.

Cheatwood, F. McNeil↗

NASA NTRS1978

Simulation of mission timelines for the Spacelab program

The paper describes the structure of the Special Purpose Simulation Language (SPSL) designed to overcome certain problems encountered in the use of the General Purpose Simulation Language (GPSL) when applied to simulation and validation of Spacelab mission timelines. The current analysis system is GROPE (Ground Resource Operations Planning Executive), the main data base models of which are the ground operations model, the mission model, the resource model, and the traffic model. Some of the simulation problem areas are mentioned, and unique features of the SPSL are highlighted.

Roberts, J. S.↗

NASA NTRS1984

Orbital flight test Shuttle External Tank flowfield and aerothermal analysis

This paper discusses the evaluation of aerothermal flight measurements made on the orbital flight test Space Shuttle External Tanks (ET). These ETs were instrumented to measure various quantities during flight including heat transfer, pressure and structural temperature. The flight data were reduced and analyzed against math models established from an extensive wind tunnel data base and empirical heat-transfer relationships. This analysis has supported the validity of the current aeroheating methodology and existing data base, but has also identified some problem areas which require methodology modifications.

Praharaj, S. C.↗

NASA NTRS1986

Orbital flight test shuttle external tank aerothermal flight evaluation, volume 1

This 3-volume report discusses the evaluation of aerothermal flight measurements made on the orbital flight test Space Shuttle External Tanks (ETs). Six ETs were instrumented to measure various quantities during flight; including heat transfer, pressure, and structural temperature. The flight data was reduced and analyzed against math models established from an extensive wind tunnel data base and empirical heat-transfer relationships. This analysis has supported the validity of the current aeroheating methodology and existing data base; and, has also identified some problem areas which require methodology modifications. This is Volume 1, an Executive Summary. Volume 2 contains Appendices A (Aerothermal Comparisons) and B (Flight Derived h sub 1/h sub u vs. M sub inf. Plots), and Volume 3 contains Appendix C (Comparison of Interference Factors among OFT Flight, Prediction and 1H-97A Data), Appendix D (Freestream Stanton Number and Reynolds Number Correlation for Flight and Tunnel Data), and Appendix E (Flight-Derived h sub i/h sub u Tables).

Praharaj, Sarat C.↗

NASA NTRS1986

Orbital flight test shuttle external tank aerothermal flight evaluation, volume 3

This 3-volume report discusses the evaluation of aerothermal flight measurements made on the orbital flight test Space Shuttle External Tanks (ETs). Six ETs were instrumented to measure various quantities during flight; including heat transfer, pressure, and structural temperature. The flight data was reduced and analyzed against math models established from an extensive wind tunnel data base and empirical heat-transfer relationships. This analysis has supported the validity of the current aeroheating methodology and existing data base; and, has also identified some problem areas which require methodology modifications. Volume 1 is the Executive Summary. Volume 2 contains Appendix A (Aerothermal Comparisons), and Appendix B (Flight-Derived h sub 1/h sub u vs. M sub inf. Plots). This is Volume 3, containing Appendix C (Comparison of Interference Factors between OFT Flight, Prediction and 1H-97A Data), Appendix D (Freestream Stanton Number and Reynolds Number Correlation for Flight and Tunnel Data), and Appendix E (Flight-Derived h sub i/h sub u Tables).

Praharaj, Sarat C.↗

NASA NTRS1986

Orbital flight test shuttle external tank aerothermal flight evaluation, volume 2

This 3-volume report discusses the evaluation of aerothermal flight measurements made on the orbital flight test Space Shuttle External Tanks (ETs). Six ETs were instrumented to measure various quantities during flight; including heat transfer, pressure, and structural temperature. The flight data was reduced and analyzed against math models established from an extensive wind tunnel data base and empirical heat-transfer relationships. This analysis has supported the validity of the current aeroheating methodology and existing data base; and, has also identified some problem areas which require methodology modifications. Volume 1 is the Executive Summary. This is volume 2, containing Appendix A (Aerothermal Comparisons), and Appendix B (Flight-Derived h sub i/h sub u vs. M sub inf. Plots). Volume 3 contains Appendix C (Comparison of Interference Factors between OFT Flight, Prediction and 1H-97A Data), Appendix D (Freestream Stanton Number and Reynolds Number Correlation for Flight and Tunnel Data), and Appendix E (Flight-Derived h sub i/h sub u Tables).

Praharaj, Sarat C.↗

NASA NTRSDate not supplied

Uncertainty Quantification Methodology for Sonic Boom Loudness of a Low-Boom Supersonic Concept

This paper presents a comprehensive analysis of uncertainty quantification for sonic boom loudness metrics associated with the X-59 aircraft during its acoustic validation phase. The study focuses on employing advanced methodologies to characterize uncertainties in key sonic boom parameters predicted from a database derived from a computational fluid dynamics (CFD) solver. These methodologies include creating a polynomial chaos expansion (PCE) surrogate model, which is then used to run a Monte Carlo analysis to obtain 95% uncertainty intervals for sonic boom loudness parameters across the full carpet. Atmospheric uncertainties are rigorously considered, leveraging weather models based on historical data near Edwards Air Force Base to simulate potential flight conditions. The findings include preliminary uncertainty results for the full carpet during the validation phase of the Quesst mission. Additionally, a sensitivity study reveals that the primary sources of uncertainty are humidity and cruise weight.

Laura M. White↗

NASA NTRS2018

Characterization and Analysis of Phoca Vitulina, Zalophus Californianus and Mirounga Angustirostris Vibrissae

Vibrissae of Phoca Vitulina (harbor seal) and Mirounga Angustirostris (elephant seal) possess undulations along their length. Harbor seal vibrissae have shown potential to reduce vortex induced vibrations and reduce drag compared to cylinders and ellipses. The exact geometry of the whiskers has not been well documented and the parameters that are responsible for the reduction in drag and vortex induced vibrations have not been characterized. Samples of six harbor seal vibrissae, six elephant seal vibrissae and six California sea lion (Zalophus californianus) vibrissae were collected from the Marine Mammal Center in California. The objectives of this study were to (1) Compare measurement techniques for digitizing and extracting parameters of the seal whiskers for the PeTaL (Periodic Table of Life) database. CT scanning, microscopy and 3D scanning techniques were compared. (2) Compare aerodynamic characteristics of a representative harbor seal whisker, elephant seal whisker, California sea lion whisker and ellipse at Re = 12000 and Re = 23000 based on major axis and free stream velocity. The data (in appendices) is available to compare CFD models or for further experimental validation, (3) Show close up images of whiskers and look for surface roughness effects. Variations in the seven parameters of the seal whisker were observed that may either be a feature of the vibration reduction mechanism or a result of natural variation. It is hypothesized that six parameters are sufficient to characterize seal whiskers based on analytic fitting. The drag coefficient of harbor seal whiskers examined in this study were found to be 25 percent lower than that of an ellipse with comparable major and minor axis lengths at Reynolds number of 12000. The dissipation length scale was found to be larger for seal whiskers. Potential applications of seal whisker morphology for aerospace are discussed. Roughness is not thought to play a factor in seal hydrodynamics.

Shyam, Vikram↗