SEARCH · Engineering Papers

Results for “STEP requirements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Design And Analysis Of Optical Communication Links

To convey to prospective designers intuitive understanding based on unique characteristics of optical communication systems, report presents method of design and analysis of outer-space optical communication link using pulse-position modulation (PPM) and in which received signal sufficiently weak to require detection by photomultiplier operating in photon-counting mode. Step 1 requires some knowledge or assumptions about parameters of transmitter and receiver. Step 2 determination of average number of background-noise photons detected during PPM timeslot. Step 3 average number, Ps of signal photons detected per signal pulse compared with average number, Pn of noise pulses detected per PPM timeslot.

Lesh, J. R.↗

NASA NTRS2017

Accuracy/Computation Performance of a New Trilateration Scheme for GPS-Style Localization

We recently introduced a new geometric trilateration (GT) method for GPS-style positioning. Preliminary singlepoint analysis using simplistic error assumptions indicates that the new scheme delivers almost indistinguishable localization accuracy as the traditional Newton-Raphson (NR) approach. Also, the same computation procedure can be used to perform high-accuracy relative positioning between a reference vehicle and an arbitrary number of target vehicles. This scheme has the potential to enable a) new mission concepts in collaborative science, b) in-situ navigation services for human Mars missions, and c) lower cost and faster acquisition of GPS signals for consumer-grade GPS products. The new GT scheme differs from the NR scheme as follows: 1. The new scheme is derived from Pythagoras Theorem, whereas the NR method is based on the principle of linear regression. 2. The NR method uses the absolute locations (xi, yi, zi)’s of the GPS satellites as input to each step of the localization computation. The GT method uses the Directional Cosines Ui’s from Earth’s center to the GPS satellite Si. 3. Both the NR method and the GT method iterate to converge to a localized solution. In each iteration step, multiple matrix operations are performed. The NR method constructs a different matrix in each iterative step, thus requires performing a new set of matrix operations in each step. The GT scheme uses the same matrix in each iteration, thus requiring computing the matrix operations only once for all subsequent iterations. In this paper, we perform an in-depth comparison between the GT scheme and the NR method in terms of a) GPS localization accuracy in the GPS operation environment, b) its sensitivity with respect to systematic errors and random errors, and c) computation load required to converge to a localization solution.

Lee, Charles↗

DOE OSTI2024

Tuning Surface, Phase, and Magnetization of Superparamagnetic Magnetite by Ionic Liquids: Single-Step Microwave-Assisted Synthesis

Achieving colloidal and chemical stability in ferrofluids by surface modification requires multiple steps, including purification, ex situ modification steps, and operation at high temperatures. In this study, a single-step microwave-assisted methodology is developed for iron oxide nanoparticle (IONP) synthesis utilizing a series of imidazolium-based ionic liquids (ILs) with chloride, bis(trifluoromethylsulfonyl)imide, and pyrrolide anions as the reaction media, thus eliminating the use of volatile organics while enabling rapid synthesis at 80 °C as well as in situ surface functionalization. The characterized surface functionality, hydrodynamic particle size, magnetization, and colloidal stability of the IONPs demonstrate a strong dependence on the IL structure, ion coordination strength, reactivity, and hydrophilicity. The IONPs present primarily a magnetite (Fe 3 O 4 ) phase with superparamagnetism with the highest saturation magnetization at 81 and 73 emu/g at 10 and 300 K, respectively. Depending on the IL coating, magnetization and exchange anisotropy decrease by 20 and 2–3 emu/g (at 35 wt % IL), respectively, but still represent the highest magnetization achieved for coated IONPs by a coprecipitation method. Further, the surface-functionalized superparamagnetic magnetite nanoparticles show good dispersibility and colloidal stability in water and dimethyl sulfoxide at 0.1 mg/mL concentration over the examined 3 month period. This study reports on the intermolecular and chemical interactions between the particle surface and the ILs under synthetic conditions as they relate to the magnetic and thermal properties of the resulting IONPs that are well suited for a variety of applications, including separation and catalysis.

36 MATERIALS SCIENCE↗

NASA NTRS2011

Rapid Calculation of Spacecraft Trajectories Using Efficient Taylor Series Integration

A variable-order, variable-step Taylor series integration algorithm was implemented in NASA Glenn's SNAP (Spacecraft N-body Analysis Program) code. SNAP is a high-fidelity trajectory propagation program that can propagate the trajectory of a spacecraft about virtually any body in the solar system. The Taylor series algorithm's very high order accuracy and excellent stability properties lead to large reductions in computer time relative to the code's existing 8th order Runge-Kutta scheme. Head-to-head comparison on near-Earth, lunar, Mars, and Europa missions showed that Taylor series integration is 15.8 times faster than Runge- Kutta on average, and is more accurate. These speedups were obtained for calculations involving central body, other body, thrust, and drag forces. Similar speedups have been obtained for calculations that include J2 spherical harmonic for central body gravitation. The algorithm includes a step size selection method that directly calculates the step size and never requires a repeat step. High-order Taylor series integration algorithms have been shown to provide major reductions in computer time over conventional integration methods in numerous scientific applications. The objective here was to directly implement Taylor series integration in an existing trajectory analysis code and demonstrate that large reductions in computer time (order of magnitude) could be achieved while simultaneously maintaining high accuracy. This software greatly accelerates the calculation of spacecraft trajectories. At each time level, the spacecraft position, velocity, and mass are expanded in a high-order Taylor series whose coefficients are obtained through efficient differentiation arithmetic. This makes it possible to take very large time steps at minimal cost, resulting in large savings in computer time. The Taylor series algorithm is implemented primarily through three subroutines: (1) a driver routine that automatically introduces auxiliary variables and sets up initial conditions and integrates; (2) a routine that calculates system reduced derivatives using recurrence relations for quotients and products; and (3) a routine that determines the step size and sums the series. The order of accuracy used in a trajectory calculation is arbitrary and can be set by the user. The algorithm directly calculates the motion of other planetary bodies and does not require ephemeris files (except to start the calculation). The code also runs with Taylor series and Runge-Kutta used interchangeably for different phases of a mission.

Scott, James R.↗

DOE OSTI2023

Inferring microbial co-occurrence networks from amplicon data: a systematic evaluation

Microbes commonly organize into communities consisting of hundreds of species involved in complex interactions with each other. 16S ribosomal RNA (16S rRNA) amplicon profiling provides snapshots that reveal the phylogenies and abundance profiles of these microbial communities. These snapshots, when collected from multiple samples, can reveal the co-occurrence of microbes, providing a glimpse into the network of associations in these communities. However, the inference of networks from 16S data involves numerous steps, each requiring specific tools and parameter choices. Moreover, the extent to which these steps affect the final network is still unclear. In this study, we perform a meticulous analysis of each step of a pipeline that can convert 16S sequencing data into a network of microbial associations. Through this process, we map how different choices of algorithms and parameters affect the co-occurrence network and identify the steps that contribute substantially to the variance. We further determine the tools and parameters that generate robust co-occurrence networks and develop consensus network algorithms based on benchmarks with mock and synthetic data sets. The Microbial Co-occurrence Network Explorer, or MiCoNE (available at https://github.com/segrelab/MiCoNE) follows these default tools and parameters and can help explore the outcome of these combinations of choices on the inferred networks. We envisage that this pipeline could be used for integrating multiple data sets and generating comparative analyses and consensus networks that can guide our understanding of microbial community assembly in different biomes.

16S rRNA↗

NASA NTRS1998

Structural Similitude and Scaling Laws

Aircraft and spacecraft comprise the class of aerospace structures that require efficiency and wisdom in design, sophistication and accuracy in analysis and numerous and careful experimental evaluations of components and prototype, in order to achieve the necessary system reliability, performance and safety. Preliminary and/or concept design entails the assemblage of system mission requirements, system expected performance and identification of components and their connections as well as of manufacturing and system assembly techniques. This is accomplished through experience based on previous similar designs, and through the possible use of models to simulate the entire system characteristics. Detail design is heavily dependent on information and concepts derived from the previous steps. This information identifies critical design areas which need sophisticated analyses, and design and redesign procedures to achieve the expected component performance. This step may require several independent analysis models, which, in many instances, require component testing. The last step in the design process, before going to production, is the verification of the design. This step necessitates the production of large components and prototypes in order to test component and system analytical predictions and verify strength and performance requirements under the worst loading conditions that the system is expected to encounter in service. Clearly then, full-scale testing is in many cases necessary and always very expensive. In the aircraft industry, in addition to full-scale tests, certification and safety necessitate large component static and dynamic testing. Such tests are extremely difficult, time consuming and definitely absolutely necessary. Clearly, one should not expect that prototype testing will be totally eliminated in the aircraft industry. It is hoped, though, that we can reduce full-scale testing to a minimum. Full-scale large component testing is necessary in other industries as well, Ship building, automobile and railway car construction all rely heavily on testing. Regardless of the application, a scaled-down (by a large factor) model (scale model) which closely represents the structural behavior of the full-scale system (prototype) can prove to be an extremely beneficial tool. This possible development must be based on the existence of certain structural parameters that control the behavior of a structural system when acted upon by static and/or dynamic loads. If such structural parameters exist, a scaled-down replica can be built, which will duplicate the response of the full-scale system. The two systems are then said to be structurally similar. The term, then, that best describes this similarity is structural similitude. Similarity of systems requires that the relevant system parameters be identical and these systems be governed by a unique set of characteristic equations. Thus, if a relation or equation of variables is written for a system, it is valid for all systems which are similar to it. Each variable in a model is proportional to the corresponding variable of the prototype. This ratio, which plays an essential role in predicting the relationship between the model and its prototype, is called the scale factor.

Simitses, George J.↗

NASA NTRS1975

Switch selector processing

The proper program execution of the switch selector commands that provide sequencing signals to the launch vehicle hardware was verified. Correct execution of each step necessary to activate a switch selector command and maintenance of the minimum timing requirements between steps are verified through analysis of a series of 6D/LVDC intermediate timing cases. Nominal and perturbed switch selector feedback conditions are simulated to verify correct processing of all realistic and timing combinations. A command which is in progress can be properly terminated by issuance of a forced reset. This is verified by forcing the conditions which require a forced reset and observing that the proper termination is completed.

Source record↗

NASA NTRS2000

Parallel Unsteady Turbopump Flow Simulations for Reusable Launch Vehicles

An efficient solution procedure for time-accurate solutions of Incompressible Navier-Stokes equation is obtained. Artificial compressibility method requires a fast convergence scheme. Pressure projection method is efficient when small time-step is required. The number of sub-iteration is reduced significantly when Poisson solver employed with the continuity equation. Both computing time and memory usage are reduced (at least 3 times). Other work includes Multi Level Parallelism (MLP) of INS3D, overset connectivity for the validation case, experimental measurements, and computational model for boost pump.

Kiris, Cetin↗

NASA NTRS2014

Detecting Trend and Seasonal Changes in Bathymetry Derived from HICO Imagery: A Case Study of Shark Bay, Western Australia

The Hyperspectral Imager for the Coastal Ocean (HICO) aboard the International Space Station has offered for the first time a dedicated space-borne hyperspectral sensor specifically designed for remote sensing of the coastal environment. However, several processing steps are required to convert calibrated top-of-atmosphere radiances to the desired geophysical parameter(s). These steps add various amounts of uncertainty that can cumulatively render the geophysical parameter imprecise and potentially unusable if the objective is to analyze trends and/or seasonal variability. This research presented here has focused on: (1) atmospheric correction of HICO imagery; (2) retrieval of bathymetry using an improved implementation of a shallow water inversion algorithm; (3) propagation of uncertainty due to environmental noise through the bathymetry retrieval process; (4) issues relating to consistent geo-location of HICO imagery necessary for time series analysis, and; (5) tide height corrections of the retrieved bathymetric dataset. The underlying question of whether a temporal change in depth is detectable above uncertainty is also addressed. To this end, nine HICO images spanning November 2011 to August 2012, over the Shark Bay World Heritage Area, Western Australia, were examined. The results presented indicate that precision of the bathymetric retrievals is dependent on the shallow water inversion algorithm used. Within this study, an average of 70% of pixels for the entire HICO-derived bathymetry dataset achieved a relative uncertainty of less than +/-20%. A per-pixel t-test analysis between derived bathymetry images at successive timestamps revealed observable changes in depth to as low as 0.4 m. However, the present geolocation accuracy of HICO is relatively poor and needs further improvements before extensive time series analysis can be performed.

coastal marine↗

NASA NTRS2014

Detecting Trend and Seasonal Changes in Bathymetry Derived from HICO Imagery: A Case Study of Shark Bay, Western Australia

The Hyperspectral Imager for the Coastal Ocean (HICO) aboard the International Space Station has offered for the first time a dedicated space-borne hyperspectral sensor specifically designed for remote sensing of the coastal environment. However, several processing steps are required to convert calibrated top-of-atmosphere radiances to the desired geophysical parameter(s). These steps add various amounts of uncertainty that can cumulatively render the geophysical parameter imprecise and potentially unusable if the objective is to analyze trends and/or seasonal variability. This research presented here has focused on: (1) atmospheric correction of HICO imagery; (2) retrieval of bathymetry using an improved implementation of a shallowwater inversion algorithm; (3) propagation of uncertainty due to environmental noise through the bathymetry retrieval process; (4) issues relating to consistent geo-location of HICO imagery necessary for time series analysis, and; (5) tide height corrections of the retrieved bathymetric dataset. The underlying question of whether a temporal change in depth is detectable above uncertainty is also addressed. To this end, nine HICO images spanning November 2011 to August 2012, over the Shark Bay World Heritage Area, Western Australia, were examined. The results presented indicate that precision of the bathymetric retrievals is dependent on the shallow water inversion algorithm used.Within this study, an average of 70% of pixels for the entire HICO-derived bathymetry dataset achieved a relative uncertainty of less than +/-20%. A per-pixel t-test analysis between derived bathymetry images at successive timestamps revealed observable changes in depth to as lowas 0.4 m. However, the present geolocation accuracy of HICO is relatively poor and needs further improvements before extensive time series analysis can be performed.

Geolocations accuracy↗

DOE OSTI2021

Accurately simulating nine-dimensional phase space of relativistic particles in strong fields

Next-generation high-power laser systems that can be focused to ultra-high intensities exceeding 10 23 W/cm 2 are enabling new physics regimes and applications. The physics of how these lasers interact with matter is highly nonlinear, relativistic, and can involve lowest-order quantum effects. The current tool of choice for modeling these interactions is the particle-in-cell (PIC) method. In the presence of strong electromagnetic fields, the motion of charged particles and their spin is affected by radiation reaction (either the semi-classical or the quantum limit). Standard (PIC) codes usually use Boris or similar operator-splitting methods to advance the particles in standard phase space. These methods have been shown to require very small time steps in the strong-field regime in order to obtain accurate results. In addition, some problems require tracking the spin of particles, which creates a nine-dimensional (9D) particle phase space, i.e., (x, u, s). Therefore, numerical algorithms that enable high-fidelity modeling of the 9D phase space in the strong-field regime (where both the spin and momentum evolution are affected by radiation reaction) are desired. Here we present a new particle pusher that works in 9D and 6D phase space (i.e., with and without spin) based on analytical rather than leapfrog solutions to the momentum and spin advance from the Lorentz force, together with the semi-classical form of radiation reaction in the Landau-Lifshitz equation and spin evolution given by the Bargmann-Michel-Telegdi equation. Analytical solutions for the position advance are also obtained, but these are not amenable to the staggering of space and time in standard PIC codes. These analytical solutions are obtained by assuming a locally uniform and constant electromagnetic field during a time step. The solutions provide the 9D phase space advance in terms of a particle's proper time, and a mapping is used to determine the proper time step duration for each particle as a function of the lab frame time step. Due to the analytical integration of particle trajectory and spin orbit, the constraint on the time step needed to resolve trajectories in ultra-high fields can be greatly reduced. The time step required in a PIC code for accurately advancing the fields may provide additional constraints. We present single-particle simulations to show that the proposed particle pusher can greatly improve the accuracy of particle trajectories in 6D or 9D phase space for given laser fields. We have implemented the new pusher into the PIC code Osiris. Example simulations show that the proposed pusher provides improvement for a given time step. A discussion on the numerical efficiency of the proposed pusher is also provided.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS2013

Workflow-Based Software Development Environment

The Software Developer's Assistant (SDA) helps software teams more efficiently and accurately conduct or execute software processes associated with NASA mission-critical software. SDA is a process enactment platform that guides software teams through project-specific standards, processes, and procedures. Software projects are decomposed into all of their required process steps or tasks, and each task is assigned to project personnel. SDA orchestrates the performance of work required to complete all process tasks in the correct sequence. The software then notifies team members when they may begin work on their assigned tasks and provides the tools, instructions, reference materials, and supportive artifacts that allow users to compliantly perform the work. A combination of technology components captures and enacts any software process use to support the software lifecycle. It creates an adaptive workflow environment that can be modified as needed. SDA achieves software process automation through a Business Process Management (BPM) approach to managing the software lifecycle for mission-critical projects. It contains five main parts: TieFlow (workflow engine), Business Rules (rules to alter process flow), Common Repository (storage for project artifacts, versions, history, schedules, etc.), SOA (interface to allow internal, GFE, or COTS tools integration), and the Web Portal Interface (collaborative web environment

Izygon, Michel E.↗

NASA NTRS1982

A new numerical method for the simulation of three dimensional flow in a pipe

A new numerical technique for simulating three dimensional, unsteady, incompressible pipe flows is presented and its utility and accuracy is shown. Each vector function in the expansion of the velocity field is divergence free and satisfies the boundary conditions for viscous flow. Some of the benefits of the expansion technique are that pressure is eliminated from the dynamics, only two unknowns per mesh point are required, implicit treatment of the viscous terms is provided at no extra computational cost, and no fractional time steps are required. The method uses spectral expansions: Fourier series in the azimuthal and streamwise directions, and Jacobi polynominals in the radial direction.

Leonard, A.↗

NASA NTRS1982

A new numerical method for the simulation of three-dimensional flow in a pipe

Leonard, A.↗

DOE OSTI2021

Exfoliation of surfactant swollen layered MWW zeolites into two-dimensional zeolite nanosheets using telechelic liquid polybutadiene

We report two-dimensional (2D) zeolites have the potential to enhance mass transport by reducing diffusion lengths and thus find applications in catalysis and separation. High aspect ratio 2D zeolite nanosheets are required for fabrication of thin, high-flux zeolite membranes. Preparation of 2D zeolite nanosheets can be achieved by exfoliation of layered zeolite precursors, which usually requires multiple steps including swelling with cationic surfactants, exfoliation by applying a mechanical force such as shearing or sonication, purification and removal of the surfactants. The exfoliation of surfactant swollen layered zeolite precursors has been studied using molten polystyrene and telechelic liquid polybutadiene, but still requires extensive shearing force. Recently, a novel one-step exfoliation method has been developed for nonswollen MWW zeolite precursors using tetrabutylammonium hydroxide (TBAOH) solution. In this work, we study the exfoliation of surfactant swollen MWW layered precursors (with and without aluminum) in commercially available liquid hydroxyl-terminated polybutadiene (HTPB) with the aim to provide fundamental understanding of the interaction between the liquid polybutadiene and the surfactant swollen layered zeolite precursors. It was found that surfactant swollen ITQ-1, (ITQ-1(S)), a pure silica layered precursor with MWW framework after being swollen with a cationic surfactant, can be exfoliated in liquid HTPB at room temperature without applying any additional shearing force. The aluminum containing surfactant swollen MWW precursors can be also exfoliated in HTPB at room temperature, but require additional shearing forces. The exfoliation process was monitored using rheology experiments and studied by tuning the composition of the zeolite precursors. The interaction between the layered zeolite precursor and the hydroxyl group of the liquid polybutadiene allows the polymer to intercalate the precursor and exfoliate it into nanosheets. The presence of framework aluminum and the nature of the organic structure directing agents (OSDAs) are key parameters affecting the exfoliation process. Framework Al is unfavorable for the exfoliation possibly due to the surface charges introduced by the aluminum. Bulky OSDA, trimethyladamantammonium (TMAda + ), in the interlayer spacing may facilitate the exfoliation.

2D nanosheets↗

NASA NTRS1982

Assessing the representativeness of wind data for wind turbine site evaluation

Once potential wind turbine sites (either for single installations or clusters) are identified through siting procedures, actual evaluation of the sites must commence. This evaluation is needed to obtain estimates of wind turbine performance and to identify hazards to the machine from the turbulence component of the atmosphere. These estimates allow for more detailed project planning and for preliminary financing arrangements to be secured. The site evaluation process can occur in two stages: (1) utilizing existing nearby data, and (2) establishing and monitoring an onsite measurement program. Since step (2) requires a period of at least 1 yr or more from the time a potential site has been identified, step (1) is often an essential stage in the preliminary evaluation process. Both the methods that have been developed and the unknowns that still exist in assessing the representativeness of available data to a nearby wind turbine site are discussed. How the assessment of the representativeness of available data can be used to develop a more effective onsite meteorological measurement program is also discussed.

Renne, D. S.↗

NASA NTRS2004

Accessing FMS Functionality: The Impact of Design on Learning

In modern commercial and military aircraft, the Flight Management System (FMS) lies at the heart of the functionality of the airplane. The nature of the FMS has also caused great difficulties learning and accessing this functionality. This study examines actual Air Force pilots who were qualified on the newly introduced advanced FMS and shows that the design of the system itself is a primary source of difficulty learning the system. Twenty representative tasks were selected which the pilots could be expected to accomplish on an ' actual flight. These tasks were analyzed using the RAFIV stage model (Sherry, Polson, et al. 2002). This analysis demonstrates that a great burden is placed on remembering complex reformulation of the task to function mapping. 65% of the tasks required retaining one access steps in memory to accomplish the task, 20% required two memorized access steps, and 15% required zero memorized access steps. The probability that a participant would make an access error on the tasks was: two memorized access steps - 74%, one memorized access step - 13%, and zero memorized access steps - 6%. Other factors were analyzed as well, including experience with the system and frequency of use. This completed the picture of a system with many memorized steps causing difficulty with the new system, especially when trying to fine where to access the correct function.

Fennell, Karl↗

NASA NTRS1986

A siphon mechanism for supplying prominence mass

A siphonlike mechanism for moving mass from the chromosphere to a gravitational well at the top of a magnetic loop to form a prominence is examined. The calculations assume no a priori flow velocity at the loop base. Instead, heating in the loop legs drives the flow. The prominence formation process requires two steps. First, the background heating rate must be reduced to on the order of 1 percent of the initial heating rate required to maintain the coronal loop. This forms an initial condensation at the top of the loop. Second, the heating must take place only in the loop legs in order to produce a pressure differential which drives mass up into the well at the top of the loop. The heating rate in the loop must be increased once the prominence has begun to form, or full prominence densities cannot be achieved in a reasonable time. It is concluded that this heating driven siphonlike mechanism is feasible for producing and maintaining prominences.

Poland, A. I.↗