Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Casting Designs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

A modified scheil approach for nucleation-dependent solidification pathways

As-solidified microstructures of near-eutectic alloys often contain multiple primary phases that are not expected from equilibrium phase diagrams. Such microstructures are caused by cooling-rate-dependent solidification pathways, a factor not captured by the Scheil–Gulliver model or variations thereof. Here, we present a model and algorithm that incorporate the critical nucleation undercooling for each solid phase into the Scheil–Gulliver model. We hypothesize that the non-equilibrium microstructure formation is primarily governed by a nucleation-competition mechanism. This mechanism accounts for both stable/metastable phase selection and primary-phase formation within eutectic regions driven by asymmetric nucleation barriers. The model is validated against a hypereutectic Al-Fe alloy, where it successfully reproduces the observed microstructural constituents, revealing the key dependencies of solidification microstructure on nucleation kinetics. Applicability to multicomponent systems is demonstrated through a hypereutectic Al–Fe–Si ternary alloy, where the model successfully predicts divorced eutectic microstructures and the associated oscillatory solidification pathways along univariant lines. As a result, the proposed framework establishes a nucleation-dependent computational approach for interpreting and predicting solidification microstructures.

Alloy design↗

FRACTURE MECHANICAL MEASUREMENTS WITH COMMERCIAL STAINLESS STEELS AT 4 K AND WITH CP-TITANIUM AT 173 K

Using the JETT (J-Evaluation on Tensile Test) technique, measurements have been performed with commercial stainless steels in forged and cast condition for the reason of an assessment for low temperature service down to 4 K. These steels frequently used for industrial applications are designated by German Werkstoff (WNr) 1.4308 and 1.4408 cast stainless steels and a forged material with the number 1.4307. The fracture toughness tests at 4 K with forged material 1.4307 comprised apart from the base metal also the weld zone and additionally the 5% and 8% pre-strained conditions of the base metal. Fracture toughness reduced slightly for cold worked condition gradually as well as for the weld joint. The Reliability of the JETT measurements has been also checked using the ASTM E 1820--99a standard. In addition, to these measurements, commercial pure ASTM grade 2 titanium (WNr 3.7035) has been also examined using the same JETT method for the reason of industrial application and the requirement of minimum fracture toughness of 100 MPasq root(m) was fulfilled at 173 K. Furthermore, test results performed at 7 K of pure titanium plate material (ASTM grade 1) with respect to fracture mechanical JETT method are presented.

36 MATERIALS SCIENCE↗

Directional solidification at ultra-high thermal gradient

A high gradient controlled solidification (HGC) furnace was designed and operated at gradients up to 1800 C/cm to continuously produce aluminum alloys. Rubber '0' rings for the water cooling chamber were eliminated, while still maintaining water cooling directly onto the solidified metal. An HGC unit for high temperature ferrous alloys was also designed. Successful runs were made with cast iron, at thermal gradients up to 500 C/cm.

Flemings, M. C.↗

Emerging polyheterocyclic films, coatings and resins - Thermoplastic polyquinolines

The processing and performance characteristics of a soluble, thermoplastic polyquinoline suggest its utility in a variety of high performance applications. The polymer is characterized by excellent thermal and oxidative stability, very low moisture absorption, good mechanical properties, very low dielectric constant, and an unusually low thermal expansion coefficient. This polymer, designated PQ-100 (TM), can be cast into strong, transparent, free standing films from common solvents. Coatings of variable thickness can be spin-coated on to silicon and other surfaces. After processing into films, PQ-100 (TM) can be rendered insoluble in a wide range of solvents using a proprietary process. The low CTE contributes to very low residual stress when the polymer is spin-coated onto silicon wafers. PQ-100 (TM) is currently under evaluation for use as an interlayer dielectric substrate in high-density interconnect applications, including multichip modules. Many of the characteristics of the polymer also suggest its utility as a high-performance film and as a matrix resin for specialty composite applications.

Hendricks, Neil H.↗

Investigation of the Formation of Topologically Close Packed Phase Instabilities in Nickel-Based Superalloy Rene N6

Topologically close packed (TCP) phase instability in third generation Ni-base superalloys is understood to hinder component performance when used in high-temperature jet engine applications. The detrimental effects on high temperature performance from these brittle phases includes weakening of the Ni-rich matrix through the depletion of potent solid solution strengthening elements. Thirty-four compositional variations of polycrystalline Rene N6 were defined from a design-of-experiments approach and then cast, homogenized, and finally aged to promote TCP formation. Our prior work reported on the results of the multiple retression modeling of these alloys in order to predict the volume fraction of TCP. This paper will present further regression modeling results on these alloys in order to predict the occurrence of TCP in third generation Ni-base superalloy microstructures. Kinetic results are also discussed.

Ritzert, Frank↗

The Interaction Between an Insoluble Particle and an Advancing Solid/Liquid Interface: Micro-Gravity Experiments and Theoretical Developments

The interaction of an insoluble particle with an advancing solid/liquid interface (SLI) has been a subject of investigation for the past four decades. While the original interest stemmed from geology applications (e.g., frost heaving in soil), researchers soon realized that the complex science associated with such an interaction is relevant to many other scientific fields encompassing metal matrix composites (MMCs), high temperature superconductors, inclusion management in steel, growth of monotectics, and preservation of biological cells. During solidification of a liquid containing an insoluble particle, three distinct interaction phenomena have been experimentally observed: instantaneous engulfment of the particle, continuous pushing, and particle pushing followed by engulfment. It was also observed that for given experimental conditions and particle size there is a critical solidification velocity, V(sub cr), above which a particle is engulfed. During solidification of MMCs pushing leads to particle agglomeration at the grain boundaries and this has detrimental effects on mechanical properties of the casting. Consequently, the process must be designed for instantaneous engulfment to occur. This implies the development of accurate theoretical models to predict V(sub cr), and perform benchmark experiments to test the validity of such models. Although considerable progress has been made in understanding the pushing/engulfment phenomenon (PEP), its quantification in terms of the material and processing parameters remains a focus of research. Since natural convection currents occurring during terrestrial solidification experiments complicate the study of PEP, execution of experiments on the International Space Station (ISS) has been approved and funded by NASA. Extensive terrestrial (1g) experiments and preliminary micro-gravity (mu g) experiments on two space shuttle missions have been conducted in preparation for future experiments on the ISS. The investigated systems included metal-ceramic particles (pure aluminum - zirconia particles) and transparent organic - non-reactive particles (succinonitrile - polystyrene and biphenyl - glass). This paper will discuss the experimental results obtained in both lg and pg conditions and the influence of the natural convection on V(sub cr). A summary of past mathematical models and our recent theoretical developments will also be presented to explain the experimentally observed particle/SLI interaction.

Catalina, Adrian V.↗

Evaluations of Additively Manufactured Superalloy Lattice Blocks

Cast lattice block structures made up of high-temperature superalloys were previously shown to offer advantages in density, efficiency, and tailored properties. However, inconsistencies in casting die-fill, composition, and microstructure were identified as persistent issues with the casting process path. Three candidate lattice designs were screened through additive manufacturing of a superalloy. Laser powder bed fusion was applied with superalloy powder to produce lattice blocks for three-dimensional octahedral unit-cell designs of three heights. Properties of the structural designs versus additively manufactured lattices were compared, including structural dimensions, densities, defects, grain structures, crystallographic texture, and surface residual stresses. Findings indicate this concept could produce useful superalloy structures for high-temperature-capable static components requiring tailored density, and thermophysical and mechanical properties.

superalloy↗

Investigation of Ring-heterogeneous Geometry Approximation for Efficient and Practical SFR Analysis

A novel geometry approximation scheme named ring-heterogeneous approximation for intermediate resolution multiphysics analysis of SFRs is presented. This approach particularly targets neutronics coupled with thermo-mechanics feedback, which dominate the passive safety of SFR designs. The ring-heterogeneous approximation casts an array of pins into volume-preserving bands of materials that constitute the pins. It allows to efficiently simulate SFRs with an unstructured mesh and also to explicitly consider the deformation of each material by retaining their heterogeneity. Verification results with single assembly and core problems of the ABTR benchmark demonstrated that the ring-heterogeneous approximation is a reasonable approximation for SFRs. For a 2D full core problem, the ring-heterogeneous approximation significantly reduced the number of elements by at least a factor of 70 from a fully-heterogeneous mesh while almost exactly preserving the reference fully-heterogeneous solutions with the RMS error of only 0.02% in the ring-wise fission reaction rate.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Cold-air performance of compressor-drive turbine of Department of Energy upgraded automobile gas turbine engine. 2: Stage performance

The aerodynamic performance of the compressor-drive turbine of the DOE upgraded gas turbine engine was determined in low temperature air. The as-received cast rotor blading had a significantly thicker profile than design and a fairly rough surface finish. Because of these blading imperfections a series of stage tests with modified rotors were made. These included the as-cast rotor, a reduced-roughness rotor, and a rotor with blades thinned to near design. Significant performance changes were measured. Tests were also made to determine the effect of Reynolds number on the turbine performance. Comparisons are made between this turbine and the compressor-drive turbine of the DOE baseline gas turbine engine.

Roelke, R. J.↗

Fabrication and Characterization of a Conduction Cooled Thermal Neutron Filter

Installation of a conduction cooled thermal (low-energy) neutron filter in an existing domestic test reactor would provide the U.S. the capability to test new reactor fuels and materials for advanced fast (high-energy) reactor concepts. A composite consisting of Al3Hf-Al has been proposed for the neutron filter due to both the neutron filtering properties of hafnium and the conducting capabilities of aluminum. Knowledge of the thermal conductivity of the Al3Hf-Al composite is essential for the design of the filtering system. The present objectives are to identify a suitable fabrication technique and to measure the thermophysical properties of the Al3Hf intermetallic, which has not been done previous to this study. A centrifugal casting method was used to prepare samples of Al3Hf. X-ray diffraction and Rietveld analysis were conducted to determine the structural make-up of each of the samples. Thermophysical properties were measured as follows: specific heat by a differential scanning calorimeter (DSC), thermal diffusivity by a laser flash thermal diffusivity measuring system, thermal expansion by a dilatometer, and thermal conductivity was calculated based on the previous measurements. All measurements were acquired over a temperature range of 90°C - 375°C with some measurements outside these bounds. The average thermal conductivity of the intermetallic Al3Hf (~7 at.% Hf) was found to be ~ 41 W/m-K for the given temperature range. This information fills a knowledge gap in the thermophysical properties of the intermetallic Al3Hf with the specified percentage of hafnium. A model designed to predict composite properties was used to calculate a thermal conductivity of ~177 W/m-K for an Al3Hf-Al composite with 23 vol% Al3Hf. This calculation was based upon the average thermal conductivity of Al3Hf over the specified temperature range.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Microstructural Evolution and Mechanical Behavior of Lead-Free Silicon Brass Manufactured by Low-Pressure Die Casting

Low-pressure die casting (LPDC) has been widely used to process aluminum and magnesium alloys; however, it has yet to be applied to manufacture brass alloys. This study investigates the microstructural evolution and mechanical behavior of a lead-free CuZnSiAl silicon brass via a variable-controlling approach on the basis of a faucet casting by LPDC. The manufactured silicon brass castings are predominantly composed of bcc β-CuZn(Si, Al) and minor fcc α-Cu(Zn, Si) solid solutions. The silicon brass castings also predominantly exhibit short rod-like or granular α phases, which distinctly differ from the acicular α morphology obtained by conventional gravity casting. The manufactured silicon brass castings which contain finer β grains and short rod-like or granular α phase exhibit superior mechanical properties. Their optimal mechanical properties—elongation of 15.0%, yield strength of 359.8 MPa, and ultimate tensile strength of 598.9 MPa—are far superior to those of the typical lead brass HPb59-1. The results obtained in this study provide insight into the manufacture and design of lead-free silicon brass castings by LDPC.

36 MATERIALS SCIENCE↗

Cast Stone Technology for the Treatment and Immobilization of Low-Activity Waste

Cast stone technology is being evaluated for potential application in the treatment and immobilization of Hanford low-activity waste. The purpose of this document is to provide background information on cast stone technology. The information provided in the report is mainly based on a pre-conceptual design completed in 2003.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Development of Lightweight Electronics Enclosures for Space Applications

This paper outlines the end to end effort to produce lightweight electronics enclosures for NASA GSFC electronics applications with the end goal of presenting an array of lightweight box options for a flight opportunity. Topics including the development of requirements, design of three different boxes, utilization of advanced materials and processes, and analysis and test will be discussed. Three different boxes were developed independently and in parallel. A lightweight machined Aluminum box, a cast Aluminum box and a composite box were designed, fabricated, and tested both mechanically and thermally. There were many challenges encountered in meeting the requirements with a non-metallic enclosure and the development of the composite box employed several innovative techniques.

Fenske, Matthew T.↗

The Development of Lightweight Electronics Enclosures for Space Applications

This paper outlines the end to end effort to produce lightweight electronics enclosures for NASA GSFC electronics applications with the end goal of presenting an array of lightweight box options for a flight opportunity. Topics including the development of requirements, design of three different boxes, utilization of advanced materials and processes, and analysis and test will be discussed. Three different boxes were developed independently and in parallel. A lightweight machined Aluminum box, a cast Aluminum box and a composite box were designed, fabricated, and tested both mechanically and thermally. There were many challenges encountered in meeting the requirements with a non-metallic enclosure and the development of the composite box employed several innovative techniques.

Fenske, Matthew T.↗

Wear of Spheroidal Graphite Cast Irons for Tractor Drive Train Components

The study was prompted by a desire to improve the wear resistance of power transmission components in rear axle drives on commercial farm tractors. Reciprocating wear tests were conducted under lubricated and non-lubricated conditions on three spheroidal cast irons which varied in strength and hardness (designated GGG450, GGG600, and GGG700). Hemispherically-tipped steel pins (designed 42CrMoS4/ 41CrS4) were used as the sliders. Except for the test duration, test procedures were similar to those described in ASTM Standard Test Method G133 for linearly-reciprocating sliding. Among the three cast irons tested, the harder and stronger the alloy, the lower was its wear rate. Wear factors were approximately four orders of magnitude lower for experiments lubricated in fresh, fully-formulated lubricating oil. There was a linear relationship between Brinell hardness of the alloys and the negative logarithm of the wear factors that were expressed in (mm3/N-m). Wear of lubricated test pins was not measurable due to the presence of deposits; however under non-lubricated sliding, the ratio of the wear of the flat specimen to that of the pin decreased as the hardness of the flat specimens approached that of the pin specimen.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Casting Aluminum Alloys: Their Physical and Mechanical Metallurgy

The follow up to the fall 2007 work on the structure, properties, thermal resistance, corrosion and fatigue of aluminum alloys in industrial manufacturing, discusses findings from the past decade, including sections on new casting alloys, novel casting technologies, and new methods of alloys design. The book also includes other hot topics, such as the implementation of computational technologies for the calculation of phase equilibria and thermodynamic properties of alloys, the development of software for calculation of diffusion processes in aluminum alloys, computational modeling of solidification microstructure and texture evolution of multi-component aluminum materials.

36 MATERIALS SCIENCE↗

High Speed Hybrid Reluctance Motor Utilizing Anisotropic Materials

With high cost and volatility driving continued efforts to decrease reliance on the critical heavy rare earth materials used in traction drive applications, General Motors developed three variants of heavy rare earth-free (HRE-free) electric motors. The variants focused on taking advantage of advanced magnet technologies and new rotor topologies to improve mechanical strength and achieve power targets. The three variants were a HRE-free permanent magnet reluctance motor, a synchronous reluctance motor utilizing small HRE-free permanent magnets, and an induction motor with inserted copper bars and cast aluminum end-rings. Motors were designed with the intent of primary or secondary traction applications, depending on the topology. Variant 1 achieved performance comparable to HRE-containing permanent magnet motors through optimized topology and validation of HRE-free magnets, focusing on achieving energy products and demagnetization resistance comparable to those of HRE-containing magnets. Demagnetization testing demonstrated the motor robustness to currents and temperatures exceeding expected vehicle conditions, a key challenge to the use of HRE-free magnets. The Variant 1 motor also showed the best capability of meeting the US Drive technology 2020 targets, due to the high power-density of the permanent magnet motor and the potential cost reductions enabled by the removal of heavy rare earth materials. Variant 2 exhibited high efficiency in high speed regions due to the low high-speed losses, an important consideration for secondary traction applications, and significantly thrifted on magnet mass to reduce cost. Variant 3 contained copper bars within the induction rotor to reduce losses compared to cast aluminum, while using cast aluminum end-rings to reduce the cost and mass of the rotor. Optimization of the Cu-Al interface were focused on, as the interface is prone to forming brittle intermetallic compounds during the casting process. Prototypes of each motor variant were built and tested for performance, mechanical strength, and demagnetization resistance (Variants 1 and 2 only), with torque and power resulting close to the predicted values.

33 ADVANCED PROPULSION SYSTEMS↗

Thin film deployable reflector model for ET gamma ray imaging telescope system (ET-GRITS)

The Marshall Space Flight Center is developing a thin film reflector for a Gamma Ray Imaging Telescope System (GRITS) using the Shuttle External Tank (ET). The concept is to install an inflatable reflector in the ET that could be transferred from the orbiter in orbit. This is a study of a scale model reflector for the ET GRITS application. The approach is to form 1/2 mil film into a spherical mirror mounted on a seven-foot diameter metal ring. The ring mount is sealed and slightly evacuated to pressurize the film into shape. Several different fabrication techniques were investigated using seamed gore designs to form the reflector. Also studied was casting a film into a seamless circular sheet. The goal for this model was to achieve a one milliradian (rms) surface curvature error over 90 percent of the reflector area. This curvature was measured by a laser scanning instrument. The results show how different reflector designs and fabrication techniques contribute to surface curvature and focusing errors.

Huegele, Vinson B.↗