Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Calvin cycle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Impact of sodium vanadium oxide (NaV 3 O 8 , NVO) material synthesis conditions on charge storage mechanism in Zn-ion aqueous batteries

The electrochemical charge storage of sodium vanadate (NaV 3 O 8 or NVO) cathodes in aqueous Zn-ion batteries has been hypothesized to be influenced by the inclusion of structural water for facilitating ion transfer in the material. Materials properties considered important (morphology, crystallite and particle size, surface area) are systematically studied herein through investigation of two NVO materials, NaV 3 O 8 ·0.34H 2 O [NVO(300)] and NaV 3 O 8 ·0.05H 2 O [NVO(500)], with different water content, acicular morphologies with different size and surface area achieved via post-synthesis heat treatment. The electrochemistry of the two materials was evaluated in aqueous Zn-ion cells with 2 M ZnSO 4 electrolyte using cyclic voltammetry, galvanostatic cycling, and rate capability testing. Furthermore, the thinner NVO(300) nanobelts (0.13 μm) demonstrate greater specific capacities and higher effective diffusion coefficients relative to the thicker NVO(500) nanorods. Notably however, while cells containing NVO(500) deliver lower specific capacity, they demonstrate enhanced capacity retention with cycling. The structural changes accompanying oxidation and reduction are elucidated via ex situ X-ray diffraction, transmission electron microscopy, and operando V K-edge X-ray absorption spectroscopy (XAS), where NVO material properties are shown to influence the ion insertion. Operando XAS verified that electron transfer corresponds directly to change in vanadium oxidation state, affirming vanadium redox as the governing electrochemical process.

25 ENERGY STORAGE↗

Effects of four-mode hydrothermal aging on three-way catalysts for passive selective catalytic reduction to control emissions from lean-burn gasoline engine

Passive selective catalytic reduction (SCR) is a promising approach for the control of NOX emissions in lean burn gasoline exhausts. It requires ammonia (NH 3 ) to be produced over a three-way catalyst (TWC) during periods of fuel-rich operation for the reduction of NO X during periods of fuel-lean operation. Previous research has shown the viability of this system but has not examined the effects of hydrothermal degradation. This work is focused on evaluating the effects of hydrothermal aging on the TWC in a passive SCR system. Two catalysts were studied: a Pd-TWC, and a NO X storage and reduction (NSR) TWC. Samples were aged at 920 °C for 100 h using a four-mode hydrothermal aging procedure. This causes the catalyst to be oxidized and reduced, as it would in a real system. The effects of aging were evaluated using simulated exhaust under both steady state and lean-rich cycling conditions. Hydrothermal aging caused significant changes in catalyst activity, leading to a decrease in low temperature conversion of carbon monoxide (CO) and propane (C 3 H 8 ) on both catalysts, and degradation of oxygen storage and NO X storage components. Furthermore, the catalysts maintained their activity for NO X conversion and NH 3 production, showing sufficient activity for the operation of a passive SCR with an optimum projected fuel consumption of 92–98% compared to stoichiometric operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Probing Sources of Capacity Fade in LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622): An Operando XRD Study of Li/NMC622 Batteries during Extended Cycling

LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) is one of the most promising Li-ion battery cathodes as it delivers high capacity at high potentials. However high potentials also lead to decreases in capacity retention where the disintegration of the secondary particles has been implicated as a major driving force of this capacity fade. This has been attributed to anisotropic lattice changes and increased microstrain during cycling. To probe how these factors affect capacity fade, Li/NMC622 batteries were cycled from 3-4.3 or 4.7 V and probed with operando X-ray diffraction over the 1st, 2nd, and 101st cycles. Further characterization with scanning electron microscopy, and inductively coupled plasmaoptical emission spectroscopy was also performed. The use of operando XRD over many cycles allowed for the collection of detailed structural information in real time over a time frame in which fading can be observed. During the first two cycles, the cells charged to 4.7 V exhibit increased anisotropic lattice changes as compared to the cells charged to 4.3 V. Upon the 101st cycle, when significant fade has been observed, the cells charged to 4.3 and 4.7 V show identical lattice changes to one another, while the 4.7 V charge limit induces more microstrain. This shows that elevated microstrain at high charge limits is a major driver for particle disintegration in NMC622 cathodes. This study provides important insights into the mechanisms of particle disintegration and capacity fade in NMC/Li-ion batteries, which will enable the design of NMC electrodes that deliver both higher capacities and exhibit better capacity retention.

25 ENERGY STORAGE↗

Implications of Power Plant Idling and Cycling on Water Use Intensity

Survey data from the Energy Information Administration (EIA) was combined with data from the Environmental Protection Agency (EPA) to explore ways in which operations might impact water use intensity (both withdrawals and consumption) at thermoelectric power plants. Two disparities in cooling and power systems operations were identified here that could impact water use intensity: 1) Idling Gap—where cooling systems continue to operate when their boilers and generators are completely idled; and 2) Cycling Gap—where cooling systems operate at full capacity, while their associated boiler and generator systems cycle over a range of loads. Analysis of the EIA and EPA data indicated that cooling systems operated on average 13% more than their corresponding power system (Idling Gap), while power systems operated on average 30% below full load when the boiler was reported as operating (Cycling Gap). Regression analysis was then performed to explore whether the degree of power plant idling/cycling could be related to the physical characteristics of the plant, its environment or time of year. While results suggested that individual power plants’ operations were unique, weak trends consistently pointed to a plant’s place on the dispatch curve as influencing patterns of cooling system, boiler, and generator operation. This insight better positions us to interpret reported power plant water use data as well as improve future water use projections.

54 ENVIRONMENTAL SCIENCES↗

Electron Density Measurements Using USPR (Final Scientific/Technical Report)

UC Davis has fabricated an ultrashort pulse reflectometer (USPR) diagnostic instrument for electron density profile measurements on compact, short duration, magnetically-confined fusion-energy concept devices such as spheromaks and FRCs. The USPR system transmits extremely short duration (~few nsec) chirped waveforms that together span 29 to 75 GHz. These chirped waveforms illuminate and reflect from the target plasma, with each frequency component reflecting from a different density layer (higher frequencies probe deeper into the plasma before reflecting). The reflected waveforms are split into roughly 42 different frequencies; time-of-flight (TOF) measurements made at each frequency with high resolution (~25 psec measurement resolution which corresponds to ~5 mm). These TOF data may then be inverted via software to generate electron density profiles with high time resolution (~10 μsec). At the heart of the system is a field programmable gate array (FPGA) based controller which collects and processes all of the USPR data in addition to generating all of the control signals required for maximum flexibility. The FPGA controller has the software flexibility to be easily reconfigured for different plasma devices, and the entire system sufficiently compact to be easily and quickly transported between devices. A high speed impulse generator was transformed into a set of three ultrashort pulse transmitter chirps using a combination of dispersive waveguide, frequency doublers and high-pass filters. A mm-wave controller was fabricated to sequentially switch between the three chirps, directing the chirps one-by-one to three different mm-wave assemblies spanning 29-75 GHz. Each mm-wave assembly consists of a high power active multiplier chain which converts the transmitter chirp to higher frequencies, and a broadband mixer which downconverts the reflected waveform to the 2-18 GHz range of the UPSR receiver. The 16-channel receiver (shared by all 3 mm-wave assemblies) was fabricated employing custom TOF modules capable of operating at a high 1 MHz sampling rate. Laboratory testing of the full system revealed the presence of unwanted harmonics from the multiplication process, with interference observed in the downconverted reflections at selected frequency channels that could not be completely filtered out. Additional interference effects arising from internal reflections within the mm-wave assemblies were minimized using a high-speed switch which served to “gate out” much of these reflections. The USPR diagnostic was transported and installed onto the HIT-SIU plasma device, becoming operational on 11/08/2022. Although designed to span 3 distinct mm-wave bands, the HIT-SIU plasmas at this time were sufficiently low density such that only the lowest of the three bands was likely to have strong plasma reflections. The system was then set to operate on only the lowest band (assembly #1), with data collected every 1 μsec rather than 3 μsec which would have been the case when cycling through all three bands. Connected to HIT-SIU, time-varying plasma reflections were observed on 9 of 16 possible frequency channels. Close examination of the data collected revealed issues previously unobserved in laboratory testing, associated with (a) reflections from the small aperture horns required for operation within the HIT-SIU device, and (b) a dependence of the recorded TOF with the threshold voltage of a given channel. Plans were made to address each of these issues before undertaking any future campaigns.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Insights into Reactivity of Silicon Negative Electrodes: Analysis Using Isothermal Microcalorimetry

Silicon offers high theoretical capacity as a negative electrode material for lithium-ion batteries; however, high irreversible capacity upon initial cycling and poor cycle life have limited commercial adoption. Herein, we report an operando isothermal microcalorimetry (IMC) study of a model system containing lithium metal and silicon composite film electrodes during the first two cycles of (de)lithiation. The total heat flow data are analyzed in terms of polarization, entropic, and parasitic heat flow contributions to quantify and determine the onset of parasitic reactions. These parasitic reactions, which include solid–electrolyte interphase formation, contribute to electrochemical irreversibility. Cycle 1 lithiation demonstrates the highest thermal energy output at 1509 mWh/g, compared to cycle 1 delithiation and cycle 2. To complement the calorimetry, operando X-ray diffraction is used to track the phase evolution of silicon. During cycle 1 lithiation, crystalline Si undergoes transformation to amorphous lithiated silicon and ultimately to crystalline Li 15 Si 4 . The solid-state amorphization process is correlated to a decrease in entropic heat flow, suggesting that heat associated with the amorphization contributes significantly to the entropic heat flow term. In conclusion, this study effectively uses IMC to probe the parasitic reactions that occur during lithiation of a silicon electrode, demonstrating an approach that can be broadly applied to quantify parasitic reactions in other complex systems.

25 ENERGY STORAGE↗

High capacity vanadium oxide electrodes: effective recycling through thermal treatment

This study demonstrates that thermal regeneration is an effective approach to convert degraded phases to functioning electroactive materials, restore functional delivered capacity and recover material crystallinity while retaining the integrity of the parent electrode. V 2 O 5 nanowires were synthesized through a facile hydrothermal method and used to fabricate V 2 O 5 /carbon nanotube (CNT) binder free electrodes. Discharge of the V 2 O 5 –CNT electrodes coupled with operando energy dispersive X-ray diffraction shows no evidence of phase segregation throughout the 150 μm thick binder free electrodes indicating full utilization of a thick electrode. When V 2 O 5 is highly electrochemically lithiated (x > 2 in LixV 2 O 5 ), irreversible phase transformation to ω-LixV 2 O 5 was observed, accompanied by a capacity decrease of ~40% over 100 cycles. A simple thermal treatment of the entire electrode results in a delivered capacity equal to or higher than the original value. Both phase conversion and an increase in material crystallinity as a result of thermal treatment are observed where structural analysis indicates the formation of Li 1 V 3 O 8 . The electrode design approach with thick electrodes and functional thermal regeneration may provide a broader choice of electroactive materials through decreasing the environmental burden by extending the lifetime of energy storage systems.

25 ENERGY STORAGE↗

Elucidating Cathode Degradation Mechanisms in LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811)/Graphite Cells Under Fast Charge Rates Using Operando Synchrotron Characterization

Li-ion batteries capable of extreme fast charging (XFC) are in demand to facilitate widespread electric vehicle (EV) adoption. While the impact of fast charge on the negative electrode has been studied, degradation of state-of-the-art NMC811 under XFC conditions has not been studied in detail. Herein, cathode degradation is probed in NMC811/graphite batteries by analysis of structural and chemical changes for recovered samples previously cycled under XFC conditions and during typical cycling. NMC surface reconstruction, as determined by soft X-ray absorption, was not detected for recovered electrodes. Furthermore, bulk redox activity from X-ray absorption near edge structure measurements showed more change in the oxidation state of Ni and Co under the 1C charge rate compared to the 4C rate consistent with the electrochemistry. Increased unit cell volume contraction under the 1C rate as determined by operando X-ray diffraction suggests that higher charge rates may provide a protective effect on the cathode by reducing structural distortion due to less delithiation.

25 ENERGY STORAGE↗

Achieving Stable Molybdenum Oxide Cathodes for Aqueous Zinc‐Ion Batteries in Water‐in‐Salt Electrolyte

Abstract Layered MoO 3 represents a promising cathode for aqueous rechargeable Zn‐ion batteries, but the implementation of this material is limited due to the low conductivity and poor structural stability. A 30 m ZnCl 2 water‐in‐salt electrolyte (WISE) is introduced to a MoO 3 nanobelt cathode for the first time, significantly increasing the stability of MoO 3 cathodes compared to those in 3 m ZnSO 4 and 3 m ZnCl 2 . The Zn/MoO 3 cell in WISE unambiguously demonstrate significantly improved rate performance delivering 349, 253, and 222 mAh g −1 at 100, 500, and 1000 mA g −1 , denoting a 12× capacity increase of those achieved in 3 m electrolytes at 1000 mA g −1 . A capacity retention rate of 73% is achieved after (dis)charging at 100 mA g −1 for 100 cycles, and no obvious capacity fading is observed at higher current densities of 500 mA g −1 and 2 A g −1 . Specifically, the data suggest that the drastic fading in 3 m electrolytes can be attributed to the parasitic surface deposits on Zn originated from Mo dissolution and H 2 formation due to Zn corrosion and hydrogen evolution reaction, which are significantly suppressed in the WISE. The direct visualization of these side reactions is achieved for the first time in the Zn‐MoO 3 system, using an in situ optoelectrochemical measurement.

Wang, Lei↗

Energy performance augmentation of domestic refrigerators with microchannel condensers

Refrigerators are one of the most extensively used household appliances, accounting for approximately 4% of total household electricity consumption. Enhancing their energy performance can significantly reduce residential energy demand. As a result, this study focuses on reducing the energy consumption of a French-door, bottom-mount refrigerator using isobutane (R600a) as the working fluid. Here, the performance improvement of the refrigerators has been obtained mainly through improving the vapor compression refrigeration cycle, with a particular emphasis on condenser design. This study explores the impact of three-pass serpentine microchannel condenser on energy performance, along with the effects of two distinct fan combinations. Charge optimization experiments were conducted to identify the optimal refrigerant mass for the refrigerator unit with microchannel condenser. Additionally, a comprehensive numerical model was developed to analyze the behavior of vapor compression cycle under various refrigerant charges. The experimental findings revealed that the refrigerator unit with the three-pass microchannel condenser reduces the energy consumption of isobutane-based domestic refrigerators up to 16% while reducing the refrigerant charge by 11% in comparison to the refrigerator unit with conventional wire-and-tube condenser.

Charge optimization↗

Marine Shallow Cloud Adjustments to the Presence of Shortwave-Absorbing Aerosols: Advancing Understanding Through a Combined Analysis of Lasic Datasets and Process Modeling (Final Report)

This is a final report for this award, whose purpose was to support the analysis of data emanating from the LASIC (Layered Atlantic Smoke Interaction with Clouds) campaign. (Layered Atlantic Smoke Interactions with Clouds) is a strategy to improve our understanding of aged carbonaceous aerosol, its seasonal evolution, and the mechanisms by which clouds adjust to the presence of the aerosol. The observational strategy centers on deploying the AMF1 cloud, aerosol, and atmospheric profiling instrumentation to Ascension Island, located within the trade-wind shallow cumulus regime (14.50W, 80S) 3000 km offshore of continental Africa. The location is within the latitude zone of the maximum outflow of aerosol, with the deepening boundary layer known to entrain free-tropospheric smoke. The primary activities for LASIC are: 1) to improve current knowledge on aged biomass burning aerosol and its radiative properties as a function of the seasonal cycle; 2) to use surface-based remote sensing to sensitively interrogate the atmosphere for the relative vertical location of aerosol and clouds; 3) to improve our understanding of the cloud adjustments to the presence of shortwave-absorbing aerosol within the vertical column, both through aerosol-radiation and through aerosol-cloud interactions; 4) to aid low cloud parameterization efforts for climate models. This award serves to further these activities and includes a sub-award to Dr. Pablo Saide at UCLA for activities 3) and 4).

54 ENVIRONMENTAL SCIENCES↗

Trade-offs of different land and bioenergy policies on the path to achieving climate targets

Many papers have shown that bioenergy and land-use are potentially important elements in a strategy to limit anthropogenic climate change. But, significant expansion of bioenergy production can have a large terrestrial footprint. In this paper, we test the implications for land use, the global energy system, carbon cycle, and carbon prices of meeting a specific climate target, using a single fossil fuel and industrial sector policy instrument—the carbon tax, but with five alternative bioenergy and land-use policy architectures. We find that the policies we examined have differing effects on the different segments of the economy. Comprehensive land policies can reduce land-use change emissions, increasing allowable emissions in the energy system, but have implications for the cost of food. Bioenergy taxes and constraints, on the other hand, have little effect on food prices, but can result in increased carbon and energy prices.

54 ENVIRONMENTAL SCIENCES↗

Initial Design of SABRE Fueled Molten Salt Experiment Irradiation Vehicle

Molten Salt Reactors (MSRs) are emerging as promising advanced reactor technologies, utilizing molten salts for both fuel and primary cooling. These reactors may offer advantages such as passive safety, enhanced economic viability, and efficient waste reprocessing while operating at high temperatures and low pressures, which leads to increased system efficiency and reduced mechanical stress on containment structures. However, challenges arise from the complex chemistry and high corrosion rates of fueled molten salts, alongside the volatility of certain fission products during irradiation. The accumulation of these fission products can alter the fuel salt chemistry, affecting corrosion potential and radioactive source terms. Therefore, understanding these phenomena under neutron irradiation is essential for future MSR designs. The SABRE (Salt and Actinide Burnup in a Reactor Environment) experiment, currently in conceptual design at Idaho National Laboratory (INL), aims to investigate these challenges by conducting a drop-in capsule experiment in the Advanced Test Reactor (ATR). The primary objectives include achieving a minimum burnup of 2 GWd/MTU and characterizing fission products while studying corrosion behavior in molten salt systems. This innovative experiment will leverage recent advancements in ATR capabilities, allowing for the safe irradiation of molten salts, thereby advancing the understanding and qualification of MSR technology for future nuclear power generation.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Performance Evaluation of Various Configurations for Domestic Refrigerators with R600a

The increasing global focus on mitigating global warming has driven a change in refrigerant selection for domestic refrigerators. While most existing refrigerators use R-134a as their working fluid, there is a gradual shift towards R600a in newly manufactured products to minimize environmental impact. In order to design a more energy-efficient isobutane refrigerator, various configurations, including both single-evaporator and dual-evaporator cycles, were investigated. The study was conducted using a high-fidelity simulation platform, the Heat Pump Design Model (HPDM), developed and experimentally validated by the US DOE/ORNL. This platform includes detailed segment-to-segment heat exchanger model, fan model, and compressor model, utilizing refrigerant properties from REFPROP 10. A quasi-steady-state approach was employed to simulate the transient behavior and performance of a domestic refrigerator. The performance of various configurations was compared, and the effects of the refrigerant properties and operating conditions were also analyzed and discussed.

Yang, Cheng-Min↗

Catalytic Upgrading of Biomass Pyrolysis Vapors at Bench Scale with Pt/TiO2

Vapor phase upgrading can produce a liquid of lower oxygen and higher energy density than can fast pyrolysis alone. Therefore, it is anticipated that catalytic pyrolysis followed by a single stage of hydrotreating will be a more cost-effective route to hydrocarbon fuels than fast pyrolysis with multiple-stage or more-severe hydrotreating. To this end, a bench-scale bubbling fluidized bed pyrolyzer was operated at 150 g/h feed rate of pine flour with a 100 g fixed-bed catalytic upgrader. A 0.5% Pt/TiO2 catalyst produced a lower oxygen (< 20%) liquid at 40% carbon efficiency at 400 degrees C and biomass-to-catalyst ratio (B:C) of 3 for numerous cycles. The catalyst was regenerated and reused by oxidation with air and reduction with hydrogen. The oxidation and reduction times were reduced to 2 h and 1 h respectively without compromising performance or catalyst temperature control. Increasing the pyrolysis temperature from 500 degrees C to 550 degrees C allowed operation at B:C greater than 3 at comparable performance. Performance was generally similar to 2% Pt/TiO2 but at reduced catalyst cost. Projected costs are < $4/gallon of gasoline blendstock. Responses to other parameter changes and prospects for further improvements will be discussed.

09 BIOMASS FUELS↗

Catalytic Upgrading of Biomass Pyrolysis Vapors at Bench Scale with Platinum on Titania

Vapor phase upgrading can produce a liquid of lower oxygen and higher energy density than can fast pyrolysis alone. Therefore, it is anticipated that catalytic pyrolysis followed by a single stage of hydrotreating will be a more cost-effective route to hydrocarbon fuels than fast pyrolysis with multiple-stage or more-severe hydrotreating. To this end, a bench-scale bubbling fluidized bed pyrolyzer was operated at 150 g/h feed rate of pine flour with a 100 g fixed-bed catalytic upgrader. A 0.5% Pt/TiO2 catalyst produced a lower oxygen (< 20%) liquid at 40% carbon efficiency at 400 degrees C and biomass-to-catalyst ratio (B:C) of 3 for numerous cycles. The catalyst was regenerated and reused by oxidation with air and reduction with hydrogen. The oxidation and reduction times were reduced to 2 h and 1 h respectively without compromising performance or catalyst temperature control. Increasing the pyrolysis temperature from 500 degrees C to 550 degrees C allowed operation at B:C greater than 3 at comparable performance. Performance was generally similar to 2% Pt/TiO2 but at reduced catalyst cost. Projected costs are < $4/gallon of gasoline blendstock. Responses to other parameter changes and prospects for further improvements will be discussed.

09 BIOMASS FUELS↗

Measurements of short-lived fission product yields from photofission of 238 U using 13.0 MeV monoenergetic photons

Photon-induced fission product yield (FPY) measurements were conducted on the isotope 238U. Fission was induced using Eγ = 13.0 MeV monoenergetic photons produced by the Triangle Universities Nuclear Laboratory’s (TUNL’s) High Intensity γ-ray Source (HIγS) facility. Short-lived FPYs were measured by performing cyclic activation of the sample using a rapid target transfer system. Following activation, the 238U target was rapidly (0.4 s) transferred to a counting station consisting of two well-shielded high-purity germanium (HPGe) detectors. The irradiation-counting cycle was repeated until the summed data had sufficient statistical accuracy. Twenty-eight unique fission products with half-lives ranging from 1 s to 450 s were identified, and their cumulative FPYs determined. Furthermore, the results are compared with previous independent FPY measurements using inverse kinematics. Good agreement between the data sets is found despite the different excitation energy distributions of the fissioning nucleus in the experiments.

Physics - Nuclear physics and radiation physics↗

Thiohalorhabdus methylotropha sp. nov., an extremely halophilic autotrophic methylotiotroph from hypersaline lakes

So far, there have been no reports of trimethylamine (TMA)-utilizing extremely halophilic microorganisms in hypersaline habitats. Our aerobic enrichments at 4 M total Na + with 5 mM TMA inoculated with surface sediments from hypersaline soda (at pH 9.5) or chloride-sulfate (at pH 7) lakes in southwestern Siberia were successful only for the latter. The initial enrichment included both bacteria and haloarchaea but only the bacterial component was able to grow as a pure culture with TMA. Strain Cl-TMA forms a new-species lineage within the genus Thiohalorhabdus which includes extremely halophilic and obligate lithoautotrophic sulfur-oxidizing gammaproteobacteria. Cl-TMA can grow methyloautotrophically utilizing TMA, dimethylamine (DMA) and methanol (MeOH) as the electron donors or chemolithoautotrophically with thiosulfate. Mixotrophic growth was also observed with the three methyl compounds and thiosulfate. Carbon is assimilated autotrophically via the Calvin-Benson-Basham pathway. Unlike the type species of Thiohalorhabdus, T. denitrificans , Cl-TMA was incapable of anaerobic growth via denitrification. The isolate belongs to extreme halophiles growing between 2.5 and 5 M NaCl with an optimum at 3–3.5 M. Genome analysis identified two gene clusters coding for PQQ-dependent methanol dehydrogenases (MxaFI and XoxF), four homologues of the formaldehyde activating enzymes (Faes), a TMA/DMA oxidation locus, and two cluster of genes encoding an N-methylglutamate dehydrogenase pathway (NMGP) for methylamine oxidation. The first steps of C 1 -subtrate conversions are followed by the tetrahydrofolate (THF)-linked and tetrahydromethanopterin (H4MPT)-linked formaldehyde oxidation pathways and two formate dehydrogenases. All of those signatures of methylotrophy were absent in T. denitrificans . In contrast, genes for two key sulfur oxidation enzymes, thiosulfate dehydrogenase TsdAB and sulfide dehydrogenase FccAB, that are present in the type species are missing in Cl-TMA. Thiosulfate is oxidized to sulfate by a combination of an incomplete Sox cycle and an sHdr system. Strain Cl-TMA T (JCM 35977 = UQM 41915) is proposed to be classified as Thiohalorhabdus methylotrophus sp. nov.

59 BASIC BIOLOGICAL SCIENCES↗