SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This project developed ceramic-metal (cermet) composite materials reinforced with embedded metal lattices. The goal of the project was to develop materials that have a higher tensile and compressive strength as well as greater fracture toughness than conventional boron carbide-aluminum cermets. These materials have applications in structural applications as well as advanced vehicle and personnel armors.
Geothermal energy has been underutilized in the U.S., primarily due to the high cost of drilling in the harsh environments encountered during the development of geothermal resources. Drilling depths can approach 5,000 m with temperatures reaching 170 C. In situ geothermal fluids are up to ten times more saline than seawater and highly corrosive, and hard rock formations often exceed 240 MPa compressive strength. This combination of extreme conditions pushes the limits of most conventional drilling equipment. Furthermore, enhanced geothermal systems are expected to reach depths of 10,000 m and temperatures more than 300 °C. To address these drilling challenges, Sandia developed a proof-of-concept tool called the auto indexer under an annual operating plan task funded by the Geothermal Technologies Program (GTP) of the U.S. Department of Energy Geothermal Technologies Office. The auto indexer is a relatively simple, elastomer-free motor that was shown previously to be compatible with pneumatic hammers in bench-top testing. Pneumatic hammers can improve penetration rates and potentially reduce drilling costs when deployed in appropriate conditions. The current effort, also funded by DOE GTP, increased the technology readiness level of the auto indexer, producing a scaled prototype for drilling larger diameter boreholes using pneumatic hammers. The results presented herein include design details, modeling and simulation results, and testing results, as well as background on percussive hammers and downhole rotation.
Battelle has demonstrated a patented process for making high-value, polyurethane (PU) foam from coal, based on preparing liquefied coal via direct liquefaction, converting it to polyols as an intermediate via ozonation, and then making PU foams from these polyols. This process represents a breakthrough in innovative utilization of U.S. coals, and is applicable to bituminous as well as sub-bituminous coals. The resulting PU foam products are projected to have an extremely high value (i.e., over $\$5,000$ /ton), with nearly 100% of carbon utilization from coalderived liquid feedstock, and 31.5% to 43.5% of the carbon in the PU foam polyol product being bio-based. The targeted products represent an extremely large (i.e., over $80 billion/year), existing PU foam market, which could expand into making coatings and adhesives. The process can further help reduce petroleum imports, while improving the economics of PU foam production. This work was completed with funding from the National Energy Technology Laboratory (NETL), with cost share from the State of Ohio’s Ohio Development Services Agency (ODSA) and others, and has advanced the process to 10 kg/day continuous scale and thus to Technology Readiness Level (TRL) 5. A total of 48 coal-based polyols were prepared and evaluated. The initial 28 polyols focused on range finding for ideal conditions. The later 20 polyols were produced as part of process optimizations. These optimizations were targeted around a continuous ozonolysis process to evaluate extended time reactions and to create the necessary intermediate for production of 1-gallon samples of polyol. The most unique attribute of Battelle’s polyol is in the utilization of coal’s aromaticity to gain final foam rigidity. Typically, polyols depend on the isocyanate fraction and cross-linking to gain rigidity. By utilizing coal, we were able to maintain rigidity while reducing the overall hydroxyl value of the polyol. This is important as lower hydroxyl value leads to greater percent weight of the coal-based polyol because less isocyanate is required for foaming. This leads to greater foam cost savings. This report provides the details, process, and process cost models of the conversion of coal to polyols and further to PU foams. Battelle’s process begins with coal liquids. These liquids can be obtained by two processes: coal coking or pyrolysis to produce coal tar, and Battelle’s biobased coal-to-liquids (CTL) process to produce heavy syncrude after liquifying >85% coal. After liquification, Battelle utilizes ozonolysis to create functionalization on the polyaromatic coal structure. The functionalization is then converted to the final polyester polyol through transesterification, or to hydroxyamide polyol through amidification. Equivalent or better standard properties have been obtained for 2 lb/ft 3 density rigid, water and freon-alternative blown foams, including compressive strength, density, R-value, and dimensional stability. Target applications for these foams are insulation, packaging, and energy-absorbing foams. Some exploratory testing also showed promise for adhesives applications. A detailed economic analysis showed that Battelle’s polyol process is economical, at a 140 metric tons per day (MTD) polyol production scale. An attractive return on investment (ROI) at competitive pricing validates the process is ready for a pilot-plant demonstration. A scale-up plan is provided.
Rutgers University, Lawrence Livermore National Laboratory, and the University of Arizona executed this program over 36 months with a 4-Task Program: (M1)-Microbial Engineering (M2)-Microstructure Modelling, (M3) Cement and Concrete Formulation, (M4)-Techno-economic analysis (TEA) and lifecycle assessment (LCA). This program developed a new carbonate cement concrete manufacturing process called microbial curing (MBC). MBC utilizes in-situ microbial production of CO 2 that dissolves into pore-bound water to carbonate a cementitious material creating a bonding matrix of CaCO 3 and SiO 2 that hardens and densifies the material. This is the first work of this type where calcium silicate was used in microbial studies. All other work reported in the literature always used a soluble form of calcium. This final report describes the work done in the final quarter, the best procedures and results, and the final techno-economic and lifecycle analyses. This quarter, we cast and cured twenty-five (4”x8”) cylinder samples. The compressive strength, split tensile, Young’s modulus, chloride permeability, and creep measurements were performed. These measurements demonstrated that MBC of calcium silicate concrete exhibits scaling problems due to the escape of ammonia gas, a product of the microbial reaction to generate CO 2 . As curing proceeds, the ability for the gas to escape from within the cylinder is restricted by the outer cylindrical portions densifying, making the outer portion highly impermeable to gas flow. In contrast, the small samples cured are uniformly cured, forming materials whose mechanical properties are 7x better than the large samples. This problem needs to be solved before this technology can be commercialized. The techno-economic and lifecycle analyses indicate that the technology developed in this program exhibits a significant opportunity to reduce the cost of cement and CO 2 emissions associated with concrete, provided the curing issue associated with larger samples can be addressed.
This award allowed the University of Kentucky to demonstrate a number of key objectives. The focus of the project was on creating a belite cement, and concrete, that demonstrated a greatly reduced CO 2 demand for manufacture and enabling the development of extremely durable concrete. The accomplishments of the developed technology includes the following, as compared to Ordinary Portland cement: 2x greater compressive strength; 10x greater corrosion resistance; 35 – 50% less estimated clinker and mill energy use; 15 – 20% less estimated cement manufacturing cost; 35% more estimated clinker capacity; 25 – 30% less estimated cement CO 2 footprint.
Coal-based bricks and blocks (CBBs) were formulated using anthracite and thermoplastic binder. Lab scale test composites were formed by hot-press molding and commercial extrusion for test articles and for a full-scale prototype. Formulations and test matrices followed a systematic experimental design to examine the effects of and interactions among three primary independent variables: a) thermoplastic type, b) weight fractions of binder relative to the total anthracite weight, and c) relative proportions of large versus small (milled) anthracite size fractions. Technical performance metrics include compressive strength, modulus, porosity/permeability and density. These DoE studies establish composition-property relations and identify the best combination for any desired property of interest – in particular, strength. Based on CBB composition and fabrication process, validated against technical performance metrics, a techno-economic analysis was constructed which incorporated a process flow model, engineering design (with scaling), and calculated capital plus operating costs. Based on measured property metrics and estimated process economics and a projected price by TEA (techno-economic analysis), building and construction target markets were identified by a market survey assessment. With known cost, price, performance metrics and competitive advantages for CBBs matched with commercial applications/uses, a technical gap analysis was performed to identify further development required for scale-up and commercialization.
The main goal of this project was to increase the beneficial use of fly ash as a supplementary cementitious material for precast concrete applications. A major focus was to develop balanced concrete mix design strategies which collectively satisfy the follow objectives: 1) increase fly ash beneficial use by at least 15% in the precast concrete industry, 2) maintain or exceed stringent structural property requirements (e.g., compressive strength at initial prestress, modulus of rupture, etc.), 3) exhibit little or no additional cost relative to conventional mixtures, and 4) mitigate detrimental environmental consequences inadvertently caused by increased beneficial use. Outcomes from this project include recommendations for design guidelines and code provisions for sustainable concrete mix designs, facilitating diversion and harvesting of large quantities of fly ash from landfills or impoundments, and multiple frameworks for incorporating discarded fly ash materials (i.e., landfilled or ponded fly ash after separating the impurities) in concrete construction.
During this LDRD project, our team developed a technology which enables the fabrication of novel nanostructures replicating seashell – “nature’s toughest material”. The resulting coatings exhibit high thermal stability up to 1650°C, which exceeds the hardness of Spectra® by ~44%, as well as the compressive strength of aluminum by ~57%. Coatings made with this technology are stronger, environmentally friendly, more sustainable, and more versatile than other comparable materials. Beryllium wafers, the current, most favorable shielding material in terms of thermal and mechanical properties, are very toxic and cost hundreds of times more than the new material developed in this project. The coatings on silicon wafer and stainless steel, respectively, have been tested as ride-along on the Z machine and clearly outperform the bare substrate. Use of this technology will have a profound global impact for pulsed power and fusion energy development, debris mitigation for spacecraft and satellites, durability of drill bits used in deep well drilling and tunnel boring operations, thermal protection of aircraft and manned spacecraft, and various other thermal and mechanical protection applications.
Lawrence Livermore National Laboratory (LLNL) is interested the quasi-static to dynamic mechanical response and microstructure evolution of tantalum-tungsten (Ta-W) alloys (Ta-2.5W, Ta-5W, and Ta-10W, wt.%) made by conventional wrought processing and additive manufacturing (AM). This work scope was performed at the Colorado School of Mines (Mines) and included quasi-static (e.g., 10 -3 s -1 ) mechanical testing in tension and compression, along with selected high strain rate (Kolsky) pressure bar testing in compression (e.g., 10 3 s -1 ), with and without temperature variations in some instances. Complementary microstructure characterization was performed on undeformed and deformed samples to understand the role of processing on microstructural evolution and the deformation mechanisms that impact the mechanical response with variations in strain rate, temperature, and strain state (e.g., tension versus compression in selected examples). The wrought material provided by LLNL from Viridis Materials was found to have unrecrystallized regions within the microstructure, which led to unexpected results relative to previously reported properties for Ta-W. The AM Ta-2.5W (wt.%) material provided by LLNL was found to have higher compressive strength than wrought Ta-2.5W (wt.%), which is hypothesized to be due to differences in the crystallographic texture between the two materials. This project partially supported several postdocs and graduate students at Mines.
Anthropogenic sources of carbon dioxide are generated from a number of sources, but the key among these are ordinary Portland cement (OPC) production and combustion of fossil fuels. Cement production is the largest global CO 2 source from the mineral decomposition of carbonates. This is due to the clinkering process whereby limestone (mainly consisting of CaCO 3 ) is decomposed into CaO and CO 2 , and combined with silica rich clays at high temperatures to form clinkers (i.e. the four key minerals that comprise cement). The high temperature range of 1400 – 1550°C required for this process accounts for up to 60% of the generated CO 2 from cement production. Combination of the limestone decomposition and thermal requirements of the clinkering process causes cement production to contribute 8-9% of annual global CO 2 emissions. Combustion of fossil fuels (coal, oil and gas) was shown to contribute a much larger portion of global CO 2 emissions. As of 2018, combustion of fossil fuels accounted for 65% of global CO 2 , where 41% was derived from stationary sources for electricity and heat generation and the other 24% was related to transport. To reduce these contributions, key steps forward in CO 2 utilization technologies are required. Therefore, a CO 2 mineralization technology (CO 2 mineralization concrete) to reduce the OPC content in concrete, while utilizing flue gas emissions from fossil fuel combustion has been developed to address both areas simultaneously. This Reversa™ technology utilizes low-carbon cementation agents produced by in situ CO 2 mineralization (“mineral carbonation reactions”) to offer a promising alternative to OPC. CO 2 mineralization relies upon the reaction of dissolved CO 2 with inorganic alkaline reactants to precipitate mineral carbonates (e.g., CaCO 3 ), which bind proximate particles and achieve cementation. Herein, a concrete green body, which is composed of a mixture of binder, water, and mineral aggregates, is exposed to CO 2 borne in industrial flue gas streams. This manner of CO 2 mineralization allows the production of construction components that feature equivalent engineering attributes as their OPC-based counterparts while featuring a much smaller embodied carbon intensity (eCI). The purpose of this project is to demonstrate the feasibility of the Reversa process evolving from a TRL-3 technology at the bench-scale up to TRL-6 technology at the pilot-scale. The reliability of the Reversa technology was tested to prove the effective production of three standard industrial concrete products selected during the course of the project. The results detailed herein will demonstrate the evolution of this technology to the industrial scale. The culmination of this work resulted in 9 production runs completed at the National Carbon Capture Center (NCCC), Wilsonville, AL, using natural gas (NG) flue gas as the CO 2 source. Over the course of the production runs at NCCC, the CO 2 utilization as a function of time, 24-h CO 2 uptake, electricity usage, and 28-d net area compressive strength recorded for each run. Collection of this data will be used to determine the success of the demonstration goals: (1) achieving in excess of 0.2gCO 2 /g reactant , (2) achieving greater than 50% reduction in global warming potential compared to standard produced units, and (3) ensuring compliance of carbonated concrete with industry standard specifications.
The overall objective of this project was to produce a coal-based construction material that has up to ~95 weight percent (wt. %) coal with physical, chemical, and thermal properties exceeding those of ordinary Portland cement (OPC)-based construction materials. Additionally, the project aimed to minimize external binders by implementing novel mixing techniques, while exceeding the performance/cost ratio of OPC. Finally, the project was to demonstrate production of precast products via the design and fabrication of products via a bench scale process. Consistent with some of these objectives, the project successfully fabricated samples of coal-based composite materials with >80 wt% coal with physical, chemical and thermal properties on par with cement-based concrete. Select samples demonstrated compressive strengths with >7,000 psi and flexural strength of >420 psi. The composite materials minimized external binders and also demonstrated durability, as evidenced by resistance to acidic and basic solutions. Finally, larger slab and beam type samples were produced using a process developed by the Recipient, although, the process was not semicontinuous in nature. Taken together, the results of this project suggest that domestic coal has potential to serve as a replacement for cementitious materials utilized in incumbent construction technologies, which could significantly reduce the energy and emissions of the construction industry
Modernizing the manufacturing of high-performance polymer foams such as amino-poly(oxadiazole) bismaleimide (APO-BMI), a bismaleimide resin with superior thermal and compressive strength that incorporates additive manufacturing (AM) techniques, is crucial for its applications, but the parameters for AM can be challenging based on the physical properties of the associated monomer. For our applications, selective laser sintering (SLS) is typically used. SLS is a 3D printing technique that allows for complex shapes and geometries without structural supports while also providing high resolution material. However, printing thermosets like APO-BMI with SLS is challenging due to the complex melting and curing considerations required when selecting parameters. Additionally, the temperature difference between melting and curing of APO-BMI is over a hundred º C, which makes selecting a sintering window especially difficult. This work explores structural modifications of APO-BMI that may be more amenable for selective laser sintering. The effects of how different structural changes such as substitution pattern, heteroatom identity in the bridge, and bridge length affect the thermal properties of the material were also compared. All APO variants were found to have a smaller temperature window between the melting and curing peaks based on differential scanning calorimetry (DSC) which is advantageous for SLS. Small structural changes significantly altered the melting and curing properties of APO. Additionally, DSC revealed significant polymorphisms in APO-BMI and other APO variants which could be attributed to differences in thermal history and would need to be considered when adapting for SLS.
Wood is one of the most abundant biomaterials on Earth, which has been used for centuries in construction applications including furniture, roofing, flooring, and cabinetry. However, wood chips—which are a low-quality and plentiful waste byproduct of lumber milling, woodworking, and shipping operations—have low economic value and complicated disposal methods. In this paper, we propose a strategy for wood chip reuse through the fabrication of bio-based building insulation foam. Through a high-temperature chemical treatment delignification process, we introduced additional small pores within the wood chips, effectively lowering their thermal conductivity, and used them in combination with a binding agent to produce a porous insulation foam. The porous insulation foam achieved a low thermal conductivity of 0.038 W/(m·K) and a high compressive strength of 1.1 MPa (70% strain). These characteristics demonstrate that wood waste can be repurposed into an effective building material, addressing challenges in both waste management and sustainable construction.
One of the main challenges of using a high fiber volume content in a cement composite is the narrow margin of fiber volume content beyond which fibers can cause an adverse effect on the mechanical properties. In this paper, the significance of fiber size distribution and fiber volume content of different proportions of chopped and milled carbon microfibers are investigated. The mixes’ flowability showed improvement with altering the fiber size distribution despite having a high fiber content. Uniaxial compression cylinders and unnotched and notched beams were cast and then tested at 7 and 28 days of age. It was found that the compressive strength is significantly affected by fiber size distribution more than fiber volume content. On the other hand, the modulus of rupture and fracture toughness are proportional to the fiber volume content with little effect of fiber size distribution. Finally, neither high fiber volume content nor altered fiber size distribution significantly affected the elastic modulus of the fiber cement composites.
Thermoplastic materials such as PA12 and PA6 have been extensively employed in Selective Laser Sintering (SLS) 3D printing applications due to their printability, processability, and crystalline structure. However, thermoplastic-based materials lack polymer inter-chain bonding, resulting in inferior mechanical and thermal properties and relatively low fatigue behavior. Therefore, 3D printing of high-performance crosslinked thermosets using SLS technology is paramount to pursue as an alternative to thermoplastics. In this work, a thermoset resin was successfully 3D printed using SLS, and its thermal stability of printed parts after a multi-step post-curing process was investigated. Dimensionally stable and high glass transition temperature (Tg: ~300 °C) thermoset parts were fabricated using SLS. The polymer crosslinking mechanism during the printing and curing process was investigated through FTIR spectra, while the mechanical stability of the SLS 3D-printed thermoset was characterized through compression tests. It is found that 100% crosslinked thermoset can be 3D printed with 900% higher compressive strength than printed green parts.
A novel calcium carbonate cement system that mimics the naturally occurring mineralization process of carbon dioxide to biogenic or geologic calcium carbonate deposits was developed utilizing carbon dioxide-containing flue gas and high-calcium industrial solid waste as raw materials. The calcium carbonate cement reaction is based on the polymorphic transformation from metastable vaterite to aragonite and can achieve >40 MPa compressive strength. Due to its unique properties, the calcium carbonate cement is well suited for building materials applications with controlled factory manufacturing processes that can take advantage of its rapid curing at elevated temperatures and lower density for competitive advantages. Examples of suitable applications are lightweight fiber cement board and aerated concrete. The new cement system described is an environmentally sustainable alternative cement that can be carbon negative, meaning more carbon dioxide is captured during its manufacture than is emitted.
This study assessed the possibility of using polymethylhydrosiloxane (PMHS)-treated fly ash cenospheres (FCS) for formulating a thermally insulating and thermal shock (TS)-resistant cementitious blend with calcium aluminate cement. To prevent FCS degradation in an alkaline cement environment at high temperatures, the cenospheres were pre-treated with sodium metasilicate to form silanol and aluminol groups on their surface. These groups participated in a dehydrogenation reaction with the functional ≡Si–H groups within PMHS with the formation of siloxane oxygen-linked M-FCS (M: Al or Si). At high hydrothermal temperatures of 175 and 250 °C, some Si–O–Si and SiCH 3 bonds ruptured, causing depolymerization of the polymer at the FCS surface and hydroxylation of the raptured sites with the formation of silanol groups. Repolymerization through self-condensation between the silanol groups followed, resulting in the transformation of siloxane to low crosslinked silicon-like polymer as a repolymerization-induced product (RIP) without carbon. The RIP provided adequate protection of FCS from pozzolanic reactions (PR), which was confirmed by the decline in zeolites as the products of PR of FCS. Cements with PMHS-treated FCS withstood both hydrothermal and thermal temperature of 250 °C in TS tests, and they also showed improved compressive strength, toughness, and water repellency as well as decreased thermal conductivity. The lubricating properties of PMHS increased the fluidity of lightweight slurries.
Recently, the manufacturing of porous polydimethylsiloxane (PDMS) with engineered porosity has gained considerable interest due to its tunable material properties and diverse applications. An innovative approach to control the porosity of PDMS is to use transient liquid phase water to improve its mechanical properties, which has been explored in this work. Adjusting the ratios of deionized water to the PDMS precursor during blending and subsequent curing processes allows for controlled porosity, yielding water emulsion foam with tailored properties. The PDMS-to-water weight ratios were engineered ranging from 100:0 to 10:90, with the 65:35 specimen exhibiting the best mechanical properties with a Young’s Modulus of 1.17 MPa, energy absorption of 0.33 MPa, and compressive strength of 3.50 MPa. This led to a porous sample exhibiting a 31.46% increase in the modulus of elasticity over a bulk PDMS sample. Dowsil SE 1700 was then added, improving the storage capabilities of the precursor. The optimal storage temperature was probed, with -60 °C resulting in great pore stability throughout a three-week duration. The possibility of using these water emulsion foams for paste extrusion additive manufacturing (AM) was also analyzed by implementing a rheological modifier, fumed silica. Fumed silica’s impact on viscosity was examined, revealing that 9 wt% of silica demonstrates optimal rheological behaviors for AM, bearing a viscosity of 10,290 Pa·s while demonstrating shear-thinning and thixotropic behavior. This study suggests that water can be used as pore-formers for PDMS in conjunction with AM to produce engineered materials and structures for aerospace, medical, and defense industries as sensors, microfluidic devices, and lightweight structures.