Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Conductivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Mapping Thermal Conductivity at the Atomic Scale: A Step toward the Thermal Design of Materials

We describe a spatial decomposition of the thermal conductivity, termed site-projected thermal conductivity, which quantifies the thermal conduction activity at each atomic site—a critical parameter for the thermal design of materials. The method is based on the Green–Kubo formula and the harmonic approximation and requires the force-constant and dynamical matrices, as well as a relaxed structural model. Throughout the study, it uses high quality models previously tested and compared to many experiments. It discusses the method and underlying approximations for amorphous silicon, carries the detailed analysis for amorphous silicon, and then examines an amorphous-crystal silicon interface and representative carbon materials. This study identifies the sites and local structures that reduce heat transport, and quantify these (estimate the spatial range) over which these “thermal defects” are effective. It identifies filamentary structures in the amorphous silicon network which impact heat transport and electronic structure (the Urbach edge) and electronic transport.

36 MATERIALS SCIENCE↗
DOE OSTI2022

An Unbalanced Battle in Excellence: Revealing Effect of Ni/Co Occupancy on Water Splitting and Oxygen Reduction Reactions in Triple–Conducting Oxides for Protonic Ceramic Electrochemical Cells

Porous electrodes that conduct electrons, protons, and oxygen ions with dramatically expanded catalytic active sites can replace conventional electrodes with sluggish kinetics in protonic ceramic electrochemical cells. In this work, a strategy is utilized to promote triple conduction by facilitating proton conduction in praseodymium cobaltite perovskite through engineering non-equivalent B-site Ni/Co occupancy. Surface infrared spectroscopy is used to study the dehydration behavior, which proves the existence of protons in the perovskite lattice. The proton mobility and proton stability are investigated by hydrogen/deuterium (H/D) isotope exchange and temperature-programmed desorption. It is observed that the increased nickel replacement on the B-site has a positive impact on proton defect stability, catalytic activity, and electrochemical performance. This doping strategy is demonstrated to be a promising pathway to increase catalytic activity toward the oxygen reduction and water splitting reactions. The chosen PrNi 0.7 Co 0.3 O 3–δ oxygen electrode demonstrates excellent full-cell performance with high electrolysis current density of –1.48 A cm –2 at 1.3 V and a peak fuel-cell power density of 0.95 W cm –2 at 600 °C and also enables lower-temperature operations down to 350 °C, and superior long-term durability.

08 HYDROGEN↗
DOE OSTI2023

Linker-Based Bandgap Tuning in Conductive MOF Solid Solutions

Herein, the synthesis of Cu 3 (HAB) x (TATHB) 2-x (HAB: hexaaminobenzene, TATHB: triaminotrihydroxybenzene) is reported. Synthetic improvement of Cu 3 (TATHB) 2 leads to a more crystalline framework with higher electrical conductivity value than previously reported. The improved crystallinity and analogous structure between TATHB and HAB enable the synthesis of Cu 3 (HAB) x (TATHB) 2-x with ligand compositions precisely controlled by precursor ratios. The electrical conductivity is tuned from 4.2 × 10 -8 to 2.9 × 10 -5 S cm -1 by simply increasing the nitrogen content in the crystal lattice. Furthermore, computational calculation supports that the solid solution facilitates the band structure tuning. In conclusion, it is envisioned that the findings not only shed light on the ligand-dependent structure–property relationship but create new prospects in synthesizing multicomponent electrically conductive metal-organic frameworks (MOFs) for tailoring optoelectronic device applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Hydraulic constraints to stomatal conductance in flooded trees

Stomatal closure is a pervasive response among trees exposed to flooded soil. We tested whether this response is caused by reduced hydraulic conductance in the soil-to-leaf hydraulic continuum (k total ), and particularly by reduced root hydraulic conductance (k root ), which has been widely hypothesized. We tracked stomatal conductance at the leaf level (g s ) and canopy scale (G s ) along with physiological conditions in two temperate tree species, Magnolia grandiflora and Quercus virginiana, that were subjected to flood and control conditions in a greenhouse experiment. Flooding reduced g s , G s , k root and k total . Path analysis showed strong support for direct effects of k total on g s and for flood duration on k total , but not k root on k total . A process-based model that accounted for the k total reduction predicted the timeseries of G s in flood and control treatment trees reasonably well (predicted versus observed G s R 2 = 0.80 and 0.51 for M. grandiflora and Q. virginiana, respectively). However, accounting only for k root reduction in flooded trees was insufficient for predicting observed G s reduction. Together, these results suggest that hydraulic constraints were not limited to roots and highlight the need to account for flooding effects on k total when projecting forest ecosystem function using process-based models.

Plant stress↗
DOE OSTI2018

Observation of Conducting Structures in Detonation Nanodiamond Powder by Electron Paramagnetic Resonance

We have used electron paramagnetic resonance (EPR) to study high-purity detonation nanodiamond (DND) powders at room temperature. In recording the EPR signal with g factor 2.00247 and line width 0.890 mT, with automatic frequency control locking the frequency of the microwave generator (klystron) to the frequency of the experimental cavity, we observed a change in the shape of the EPR signal from the DND powder due to formation of an anisotropic electrically conducting structure in the powder. The electrical conductivity of the DND sample is apparent in the Dysonian EPR lineshape (strongly asymmetric signal with g factor 2.00146 and line width 0.281 mT) together with an abrupt shift of the baseline at the time of resonant absorption, and in the decrease in the cavity Q due to nonresonant microwave absorption. The observed effect can be explained by transition of the DND powder from a dielectric state to a state with metallic conductivity, due to spin ordering in a preferred direction.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Evaluation of measuring thermal conductivity of isotropic and anisotropic thermally insulating materials by transient plane source (Hot Disk) technique

The transient plane source (TPS) technique, also referred as the Hot Disk method, has been widely used due to its ability to measure the thermal properties of an extensive range of materials (solids, liquids, and powder). Recently, it has been recognized that typical Hot Disk sensors can influence TPS results of thermally insulating materials and lead to an overestimation of thermal conductivity. Although improvements have been proposed, they have not yet been implemented in the commercial TPS, leaving researchers with non-standardized modifications or options provided by a commercial Hot Disk apparatus. An empirical study of thermally insulating materials such as extruded polystyrene (XPS) and aerogel blanket is conducted in order to address the factors that affect the reliability of thermal conductivity k obtained using the commercial TPS apparatus. Sensor size, input power, duration of the measurements, applied pressure, and, in the case of anisotropic materials, heat capacity are investigated, and the results are compared with those using a Heat Flow Meter apparatus. The effect of sensor size on the k value is ascribed to heat loss through connecting leads and is more pronounced in smaller sensors and in materials with lower k values . In the case of XPS and aerogel, the effect becomes minimal for sensors with a radius r ≥ 6.4 mm. The low input power yields a high scattering of the results and should be avoided. Applied contact pressure and the tested region of the specimen play an important role in experiments with low-density fibrous materials due to the large percentage of heat being transferred by radiation and the heterogeneous nature of the samples, respectively. Additionally, the sensitivity of anisotropic measurements to the value of the material’s volumetric heat capacity ( ρC p ) is shown, emphasizing the need for the precise determination.

thermal conductivity↗
DOE OSTI2021

Ionic conductivity optimization of composite polymer electrolytes through filler particle chemical modification

The addition of filler particles to polymer electrolytes is known to increment their ionic conductivity (IC). A detailed understanding of how the interactions between the constituent materials are responsible for the enhancement remains to be developed. A significant contribution is ascribed to an increment of the polymer amorphous fraction, induced by the fillers, resulting in the formation of higher ionic conductivity channels in the polymer matrix. However, the dependence of IC on the particle weight load and its composition on the polymer morphology is not fully understood. This work investigates Li-ion transport in composite polymer electrolytes (CPE) comprising Bi-doped LLZO particles embedded in PEO:LiTFSI matrixes. We find that the IC optimizes for very low particle weight loads (5-10%) and that both its magnitude and the load are required, strongly dependent on the garnet particle composition. Based on structural characterization results and electrochemical impedance spectroscopy, a mechanism is proposed to explain these findings. It is suggested that the Li-molar content in the garnet particle controls its interactions with the polymer matrix, resulting at the optimum loads reported, in the formation of high ionic conductivity channels. We propose that filler particle chemical manipulation of the polymer morphology is a promising avenue for the further development of composite polymer electrolytes.

bismuth↗
DOE OSTI2019

Radiation–Conduction Heat-Transfer Study for Mold Flux by Thermoviewer-Enhanced Infrared Emitter Technique

A thermoviewer-enhanced infrared emitter technique was developed in this article to study the heat-transfer behavior of mold flux in the continuous casting mold. Then, a radiation–conduction heat-transfer model was built to determine the radiative/conductive heat flux, thermal conductivity, and optical properties of slag. The results showed that the mold/slag interfacial thermal resistance decreases with the increasing temperature of slag surface at the mold side, and then reaches the minimum when the slag surface is the hottest, and finally increases slightly with further increase in slag crystallization. In addition, the radiative heat flux decreases with the increasing depth of radiation propagating into the slag. While the amount of heat of radiation lost is being converted to produce an additional radiative heat source to heat the slag, the increase in the conductive heat flux in the slag is realized. Furthermore, the apparent transmittivity is obtained as 0.63 for the glassy slag disk and as 0.41 for the partially crystallized slag disk. Besides, when mold heat flux decreases from the maximum to a saturation value due to the further slag crystallization, the corresponding apparent transmittivity of slag disk decreases from 0.58 to 0.41, and the ratio of the heat across the slag disk by radiation decreases from 67.3 to 50.0 pct.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Study on the Deformation Homogeneity and Electrical Conductivity in Co-Cr-Ni-Mo Wires Drawn with Different Drawing Practices

This study investigates the influence of cold wire drawing practices namely full die drawing (FDD) and half die drawing (HDD) on the deformation homogeneity in Co-35Ni-20Cr-10Mo alloy (MP35N) wires which are used for manufacturing implantable medical products. The inhomogeneous factor was used to assess the level of inhomogeneity in the wires, and electrical conductivity was measured on the wires, after drawn to different cold work (CW) reductions and with different drawing practices. Electron beam scattered diffraction, field emission scanning electron microscope and transmission electron microscope characterization were performed on the wire samples to correlate the mechanical and electrical properties to their texture and grain size. The results of this study conclude that the wires drawn with the FDD practice exhibited homogenous deformation, uniform microstructural and hardness gradient across the wire when compared to HDD wires. The electrical conductivity of the HDD-drawn wires was higher than the FDD wires and the level of inhomogeneity and the variation of conductivity decreased with the increase in CW.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Investigation on Strength, Ductility and Electrical Conductivity of Cu-4Ag Alloy Prepared by Cryorolling and Subsequent Annealing Process

Cu-Ag alloy is widely used as conductive material for high-field pulsed magnets in electrical industry. The cryorolling technique is considered as the most applicable severe plastic deformation technique. Therefore, in this study, cryorolling and subsequent annealing process were used to prepare Cu-4Ag (in wt.%) alloy sheets. The strength, ductility and electrical conductivity of Cu-4Ag alloy sheets were investigated. Microstructure of Cu-4Ag alloy was also studied by OM, SEM, XRD and TEM. As a result, the cryorolling specimens after annealing at temperature of 300 °C display a good combination of tensile strength of 652.2 ± 6.0 MPa, moderate elongation of 12.5 ± 0.7% and electrical conductivity of 80.6 ± 0.2% IACS. This is due to the presence of dislocations, dislocation cells, nanograins and nanotwins in the non-recrystallized regions and fine nanoscaled silver precipitates. Besides, a good ductility is achieved in this condition due to its desirable ductile fracture characteristics.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Measurement and Simulation of Thermal Conductivity of Hafnium-Aluminum Thermal Neutron Absorber Material

A metal matrix composite (MMC) material comprised of hafnium aluminide (Al3Hf) intermetallic particles in an aluminum matrix has been identified as a promising material for fast-flux irradiation testing applications. This material can filter thermal neutrons while simultaneously providing high rates of conductive cooling for experiment capsules. Our purpose is to investigate effects of Hf-Al material composition and neutron irradiation on thermophysical properties, which were measured before and after irradiation. When performing differential scanning calorimetry (DSC) on the irradiated specimens, a large exotherm corresponding to material annealment was observed. Thus, a test procedure was developed to perform DSC and laser flash analysis (LFA) to obtain the specific heat and thermal diffusivity of pre- and post-annealment specimens. This paper presents the thermal properties for three states of the MMC material: (1) unirradiated, (2) as-irradiated, and (3) irradiated and annealed. Microstructure-property relationships were obtained for the thermal conductivity. These relationships are useful for designing components from this material to operate in irradiation environments. Furthermore, the ability of this material to effectively conduct heat as a function of temperature, volume fraction Al 3 Hf, radiation damage and annealing is assessed using the MOOSE suite of computational tools.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Additively-manufactured Al-0.3Zr-0.2Ce-0.2Cu alloy with high creep resistance and electrical conductivity

Here, a new, solute-lean Al-0.3Zr-0.2Ce-0.2Cu (wt.%) alloy is developed for additive manufacturing that overcomes the classical tradeoff between conductivity and creep resistance. The rapid-cooling-enabled supersaturation of Zr, and its uniform distribution in α-Al matrix, along with formation of submicron (Ce,Cu)-rich intermetallic particles on solidification lead to unusually high creep resistance at 200 °C. Near-zero secondary creep rates are achieved up to the alloy yield stress (YS) of 65 MPa at 200 °C in as-fabricated state. The Zr-solute-induced dislocation-climb suppression mechanism underlying this improvement also restricts dynamic recovery above YS, as noted from appreciable primary creep and its transitioning to near-zero secondary creep rates. A combination of relatively coarse, epitaxially-grown α-Al grains, low Zr concentration in α-Al, and the impurity-scavenging effect of Ce to purify α-Al matrix produces high electrical conductivity of ∼48 %IACS. Aging precipitation of L1 2 -Al 3 Zr nanoprecipitates doubles the YS (to ∼150 MPa) at room temperature and increases alloy conductivity to ∼58 %IACS, but loss of solid-solution Zr out of α-Al matrix leads to activation of dislocation climb, degrading the creep properties as compared to the supersaturated Al-Zr solid solution in the as-fabricated state. Compared to L1 2 -Al 3 Zr nanoprecipitates, submicron (Ce,Cu)-rich particles formed on solidification are more effective at impeding dislocation climb, producing a threshold stress for dislocation creep of ∼ 50 MPa at 200 °C. The new alloy design concepts, especially solute-induced dislocation-climb suppression for creep resistance, explored here may pave way for the design of new metallic alloys for thermal/electrical conductors and other high-temperature applications.

Additive Manufacturing↗
DOE OSTI2019

DC conductivity from backreacted non-linear arcsin electrodynamics

Highlights: • This model, reproduces conductivity and Hall angle of high-T{sub c} cuprates. • It exhibits metal-insulator transition under variation of magnetic field. • Obtained transport properties for a backreacted non-linear electrodynamics model. - Abstract: We consider arcsin electrodynamics in a holographic set up along with dilatonic and axionic scalar fields. Considering backreaction of the matter fields on the geometry we study direct conductivity of the dual theory and obtain the conductivity matrix. Since obtaining an exact solution is difficult in general, we have studied several limiting cases. In particular, at the strong momentum dissipation limit, we find for hyperscaling violating geometry as the background, the resistivity and Hall coefficient will behave as ∼T and ∼T{sup 2} respectively. Then we restrict to a simpler model, where we find that the variation of the magnetic field can lead to metal–insulator transition/crossover.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Amplified charge and discharge rates in phase change materials for energy storage using spatially-enhanced thermal conductivity

Composites made with high thermal conductivity meshes embedded in phase change materials (PCMs) increase charge/discharge rates of latent heat energy storage systems. Here we study the benefits of spatially-dependent enhancements to thermal conductivity on the charge/discharge rates of PCMs in both one-dimensional Cartesian and one-dimensional cylindrical coordinates. Our nondimensionalized quasi-steady (Stefan number ≲ 0.1) solution indicates that the average charge (discharge) rate in a spatially-enhanced PCM outperforms the uniformly-enhanced case by maximizing the enhancement near the heat source and therein reducing the time averaged thermal resistance to melting (solidifying). Relative to a uniformly-enhanced thermal conductivity, the optimal charge/discharge rate enhancement is a modest 12% in one-dimensional Cartesian coordinates but as high as 140% in one-dimensional cylindrical coordinates. Our analytical solutions are a design guide for graded mesh structures that can be realized by advanced fabrication techniques such as additive manufacturing and applied in applications ranging from telecommunications to buildings, where PCMs are employed to harness rapidly varying energy sources.

25 ENERGY STORAGE↗
DOE OSTI2025

Development of a conduction-based model for analyzing frozen startup of alkali-metal heat pipes

One key area of interest in heat pipe modeling/simulation is to analyze the startup behavior of the liquid-metal heat pipes (LMHPs) from a frozen state. This so-called ‘frozen startup’ process involves a complex set of nonlinear mass and heat transport phenomena, including phase transitions from solid to liquid and vapor, multiphase interactions, microporous wick flow, and compressible vapor dynamics. The complexity of these processes makes it challenging to simulate LMHP’s frozen startup using conventional numerical methods or commercial computational fluid dynamics (CFD) software. This paper presents a simplified conduction-based modeling approach that can provide practical insights into the entire LMHP frozen startup process, while alleviating the challenges of modeling its complex physics. The theoretical foundation and physical assumptions of the proposed model are based solely on heat-conduction equation, allowing for a more tractable simulation without sacrificing essential physical accuracy. The proposed model was implemented in a commercial CFD software, and its prediction was compared with the experimental data obtained from sodium heat-pipe startup experiments. The comparison highlights the proposed model's ability to capture the transient thermal behavior of LMHP during frozen startup. This study not only validates the conduction-based frozen startup modeling method but also shows its potential as a practical and efficient tool for understanding the startup performance of the LMHP systems.

Microreactor↗
DOE OSTI2022

Enhancing thermal conductivity and toughness of cellulose nanofibril/boron nitride nanosheet composites

Generally, the thermal conductivity (TC) of composite based on cellulose nanofibrils (CNF) is improved by adding thermal conductive filler, which inevitably leads to the loss of its mechanical properties. Here, in this work, it is the first to simultaneously improve the toughness and TC of CNF/boron nitride nanosheets (BNNS) composite from the perspective of thermal conductive filler addition and CNF crystal change. The hydrophilic-modified BNNSs were successfully prepared by xylose-assisted ball-milling prior to adding into CNF. Compared with that of CNF film (1.34 W/(m·K)), the in-plane TC of CNF/BNNS composite (12.68 W/(m·K)) increased significantly by 846 % with loading 30 % BNNS. Afterwards, both toughness (8.0 MJ·m -3 , increased ~250 %) and TC (14.7 W/(m·K), increased ~16 %) of CNF/BNNS composite were further enhanced significantly by mercerization with 12.5 % NaOH solution. The simultaneously improvement of toughness and TC is unprecedented in related studies, which contributes to the effective preparation of thermal management materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

3D simulations of spinlike flames in Co/Al multilayers with enhanced conduction losses

Reactive Co/Al multilayers are uniformly structured materials that may be ignited to produce rapid and localized heating. Prior studies varying the bilayer thickness (i.e., sum of two individual layers of Co and Al) have revealed different types of flame morphologies, including: (a) steady/planar, (b) wavy/periodic, and (c) transverse bands, originating in the flame front. These instabilities resemble the “spin waves” first observed in the early studies of solid combustion (i.e., Ti cylinder in a N 2 atmosphere), and are likewise thought to be due to the balance of heat released by reaction and heat conduction forward into the unreacted multilayer. However, the multilayer geometry and three-dimensional (3D) edge effects are relatively unexplored. In this work, a new diffusion-limited reaction model for Co/Al multilayers was implemented in large, novel 3D finite element analysis (FEA) simulations, in order to study the origins of these spinlike flames. This reaction model builds upon previous work by introducing three new phase-dependent property models for: (1) the diffusion coefficient, (2) anisotropic thermal conductivity tensor, and (3) bulk heat capacity, as well as one additional model for the bilayer-dependent heat of reaction. These novel 3D simulations are the first to predict both steady and unsteady flames in Co/Al multilayers. Moreover, two unsteady modes of flame propagation are identified, which depend on the enhanced conduction losses with slower flames, as well as flame propagation around notched edges. Finally, future work will consider the generality of the current modeling approach and also seek to define a more generalized set of stability criteria for additional multilayer systems.

42 ENGINEERING↗
DOE OSTI2022

Atomistic insights into the heat conductance across the interfaces between erythritol and different metals: A non-equilibrium molecular dynamics study

The heat conductance across the interface between a phase change material (PCM) and the metal shell is important for thermal design of latent heat storage systems. Non-equilibrium molecular dynamics simulations were carried out in this work to unravel, at the atomistic level, the interfacial heat conductance mechanisms between erythritol (the most promising medium-temperature polyol PCM) and two different metals (i.e., copper and aluminum). The interfacial contact ratio was introduced as a parameter to represent different contact conditions at the interfaces, for example, different surface roughness levels of the metals. It was found that with the increase of interfacial contact ratio, the temperature difference between the erythritol/metal interfaces decreases, whereas the interfacial heat transfer coefficient increases gradually. At the perfect contact condition, i.e., the interfacial contact ratio reaches 100%, the interfacial heat transfer coefficients across the erythritol/Cu and erythritol/Al interfaces were predicted to be 398 ± 26 MW/m 2 K and 544 ± 11 MW/m 2 K, respectively. The interfacial heat conductance of erythritol/Al is better than that of erythritol/Cu. The mismatch of atomic spectral density across the interfaces between erythritol and the two metals was analyzed and distinguished. These results could guide the selection of packaging materials and the thermal design of erythritol-based latent heat storage systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Refine your search to explore more results.