Results for “jet interactions” — Page 10

NASA NTRS2014

Experiments on Exhaust Noise of Tightly Integrated Propulsion Systems

A wide-ranging series of tests have been completed that seek to map the effects of installation, including jet by jet interaction effects, on exhaust noise from various nozzles in forward flight. The primary data was far-field acoustic spectral directivity. The goals of the test series were (i) to generate enough data for empirical models of the different effects, and (ii) to provide data for advanced computational noise predictions methods applied to simplified yet realistic configurations. Data is presented that demonstrate several checks on data quality and that provide an overview of trends observed to date. Among the findings presented here: (i) Data was repeatable between jet rigs for single nozzles with and without surfaces to within +/- 0.5 dB. (ii) The presence of a second jet caused a strong reduction of the summed noise in the plane of the two plumes and an increase over the expected source doubling in most other azimuthal planes. (iii) The impact of the second jet was reduced when the jets were unheated. (iv) The impact of adding a second isolated rectangular jet was relatively independent of the nozzle aspect ratio up to aspect ratio 8:1. (v) Forward flight had similar impact on a high aspect ratio (8:1) jet as on an axisymmetric jet, except at the peak noise angle where the impact was less. (vi) The effect of adding a second round jet to a tightly integrated nozzle where the nozzle lip was less than a diameter from the surface was very dependent upon the length of the surface downstream of the nozzle. (vii) When the nozzles were rectangular and tightly integrated with the airframe surface the impact of a second jet was very dependent upon how close together the two jets were. This paper serves as an overview of the test; other papers presented in the same conference will give more detailed analysis of the results.

Noise↗

DOE OSTI2024

Challenging Common Assumptions of Thick-Wall Chamber Dynamics in Inertial Fusion Systems using MOOSE

As an increasing number of companies look toward commercial Inertial Fusion Energy (IFE) designs, there is a pressing need to understand the physics of thick-wall chamber gas dynamics. The thick liquid wall approach implements a renewable wall to mitigate the fusion target emissions, thereby reducing the radiation damage rate and significantly extending the lifetime of chamber structures, leading to increased plant availability and reduced waste streams in comparison to dry wall chamber designs. It is necessary, however, to assess the critical performance and safety aspects of these systems. For example, it is crucial to predict (1) where the mass ablated from the liquid walls will vent, which determines the placement of condensing surfaces; (2) debris propagation up the beam lines, which provides essential information for design and protection requirements; (3) peak pressures and impulse on chamber walls, which affect chamber structural design; and (4) momentum transfer to the liquid jets, which constrains the shape and positioning of the jets. In turn, the chamber design and its liquid walls affect shielding requirements, material activation, and tritium fuel cycle. Currently available simulation tools, however, are unable to accurately capture key thick-wall chamber dynamics. Significant assumptions are often made to simplify the system and reduce computational cost and modeling capability needs, but the impact of these assumptions on simulation predictions has not been evaluated. For example, no three-dimensional simulations can be found in the open literature to evaluate gas venting and momentum transfer to the jets with simulations using two-dimensional domains to represent complex three-dimensional geometries. Moreover, limited studies have been dedicated to jet breakup due to both turbulence and neutron heating, and no studies have been found that evaluate how jet breakup can impact shock-jet interaction. Furthermore, effects of radiative heat transfer have rarely been included for the hydrodynamic phase of shock propagation, and integration of proper equations of state in shock dynamics codes has been mostly exploratory. In this study, we use the flexible, high-fidelity Multiphysics Object-Oriented Simulation Environment (MOOSE) to model these complex phenomena and inform design and safety studies. Capabilities to model thick-wall chamber gas dynamics are being developed, and the impact of the assumptions listed above (i.e., two-dimensional vs three-dimensional, absence of jet breakout, no radiative heat transfer, and ideal gas behavior) are being quantified.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Challenging Common Assumptions of Thick-Wall Chamber Dynamics in Inertial Fusion Systems Using MOOSE-based Multiphysics Simulations

As an increasing number of companies look toward commercial Inertial Fusion Energy (IFE) designs, there is a pressing need to understand the physics of thick-wall chamber gas dynamics. The thick liquid wall approach implements a renewable wall to mitigate the fusion target emissions, thereby reducing the radiation damage rate and significantly extending the lifetime of chamber structures, leading to increased plant availability and reduced waste streams in comparison to dry wall chamber designs. It is necessary, however, to assess the critical performance and safety aspects of these systems. For example, it is crucial to predict (1) where the mass ablated from the liquid walls will vent, which determines the placement of condensing surfaces; (2) debris propagation up the beam lines, which provides essential information for design and protection requirements; (3) peak pressures and impulse on chamber walls, which affect chamber structural design; and (4) momentum transfer to the liquid jets, which constrains the shape and positioning of the jets. In turn, the chamber design and its liquid walls affect shielding requirements, material activation, and tritium fuel cycle. Currently available simulation tools, however, are unable to accurately capture key thick-wall chamber dynamics. Significant assumptions are often made to simplify the system and reduce computational cost and modeling capability needs, but the impact of these assumptions on simulation predictions has not been evaluated. For example, no three-dimensional simulations can be found in the open literature to evaluate gas venting and momentum transfer to the jets with simulations using two-dimensional domains to represent complex three-dimensional geometries. Moreover, limited studies have been dedicated to jet breakup due to both turbulence and neutron heating, and no studies have been found that evaluate how jet breakup can impact shock-jet interaction. Furthermore, effects of radiative heat transfer have rarely been included for the hydrodynamic phase of shock propagation, and integration of proper equations of state in shock dynamics codes has been mostly exploratory. In this study, we use the flexible, high-fidelity Multiphysics Object-Oriented Simulation Environment (MOOSE) to model these complex phenomena and inform design and safety studies. Capabilities to model thick-wall chamber gas dynamics are being developed, and the impact of the assumptions listed above (i.e., two-dimensional vs three-dimensional, absence of jet breakout, no radiative heat transfer, and ideal gas behavior) are being quantified.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

MRV Challenge 3: velocity and passive scalar comparison in a 3D turbulent flow

The third iteration of a magnetic resonance velocimetry (MRV) challenge comparison activity consisting of 3D flow measurements for a turbulent flow in a water channel moving past centrally positioned cubic obstacles is reported. In this challenge iteration, MRV measurements are coupled with either temperature or concentration measurements to extend the diagnostic utility. Five research teams from around the world conducted the measurements on a single shared apparatus. The water channel included partial elements along the channel sidewalls that varied in height and precluded easy optical accessibility. In addition to a turbulent mainstream flow, a secondary flow entered the channel between the second and third cubic elements from a square injector hole at the channel bottom wall. The injector jet interacts with the mainstream flow and mixes turbulently as it advects downstream. For the selected flow regime and water solutions used as working fluids, the mixing of the higher temperature or concentration through the secondary flow with the mainstream flow satisfies the same dynamics so that both temperature and concentration fields behave as passive scalars and can be directly compared. The measurements are explained in detail by each participating team, and the results are interpolated onto a common grid and compared using line profiles, contour plots, and isosurfaces.

Benson, Mike [ORNL] (ORCID:000000023210116X)↗

DOE OSTI2020

Dimits shift, avalanche-like bursts, and solitary propagating structures in the two-field flux-balanced Hasegawa–Wakatani model for plasma edge turbulence

We show that the recently introduced two-field flux-balanced Hasegawa–Wakatani (BHW) model captures the key features of drift-wave turbulent transport mediated by zonal flows observed in more complete and accurate gyrokinetic simulations, such as the existence of a nonlinear upshift of the threshold for drift wave turbulence driven transport, often called the Dimits shift, as well as non-local transport with avalanche bursts and solitary propagating structures. Because of the approximations made in the BHW model, these observations are made for the particle flux instead of the heat flux more commonly studied in ion temperature gradient (ITG) driven turbulence in fluid or gyrokinetic codes. Many of these features are not seen in other Hasegawa–Wakatani models, which confirm the critical role of the electron dynamics parallel to the magnetic field lines. To address questions regarding the role of boundary conditions on the drift-wave zonal flow dynamics, we apply our model to both a channel domain geometry and the more typical doubly periodic geometry. We only observe strong soliton-like solutions in the particle flux for the channel geometry, in the vicinity of the boundaries, where strong velocity shear and density gradients are generated, which are absent in the doubly periodic simulations. Changing the aspect ratio of the simulation domain also has a significant effect. In domains which are elongated in the radial direction, more complex multi-scale dynamics takes place, with multiple zonal jets interacting with each other, and large scale avalanches.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Identified charged hadron production in Au+Au collisions at $\sqrt{s_{NN}}$ = 54.4 GeV with the STAR detector

Here, we present results on the production of 𝜋±, 𝐾±, 𝑝, and $\bar{𝑝}$ in Au+Au collisions at $\sqrt{𝑠_{N⁢N}}$ = 54.4~GeV using the STAR detector at RHIC, at mid-rapidity (|𝑦|< 0.1). Invariant yields of these particles as a function of transverse momentum are shown. We determine bulk properties such as integrated particle yields (𝑑 ⁢𝑁 /𝑑 ⁢𝑦 ), mean transverse momentum (⟨𝑝 𝑇 ⟩), particle ratios, which provide insight into the particle production mechanisms. Additionally, the kinetic freeze-out parameters (𝑇 kin and ⟨𝛽 𝑇 ⟩), which provide information about the dynamics of the system at the time of freeze-out, are obtained. The Bjorken energy density (𝜖 𝐵⁢𝐽 ), which gives an estimate of the energy density in the central rapidity region of the collision zone at the formation time 𝜏, is calculated and presented as a function of multiplicity for various energies. The results are compared with those from the models such as A Multi-Phase Transport (AMPT) and Heavy Ion Jet INteraction Generator (HIJING) for further insights.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2022

Two- and three-particle nonflow contributions to the chiral magnetic effect measurement by spectator and participant planes in relativistic heavy ion collisions

Correlation measurements with respect to the spectator and participant planes in relativistic heavy ion collisions were proposed to extract the chiral magnetic effect (CME) from background dominated azimuthal correlators. Here, this paper investigates the effects of two- and three-particle nonflow correlations on the extracted CME signal fraction, f CME . It is found, guided by a multiphase transport (ampt) model and the heavy ion jet interaction generator (hijing) together with experimental data, that the nonflow effects amount to approximately (4 ± 5)% and (–5 ± 3)% without and with pseudorapidity gaps, respectively, in 20–50% centrality Au + Au collisions at √ s NN = 200 GeV.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2024

Upper limit on the chiral magnetic effect in isobar collisions at the Relativistic Heavy-Ion Collider

The chiral magnetic effect (CME) is a phenomenon that arises from the QCD anomaly in the presence of an external magnetic field. The experimental search for its evidence has been one of the key goals of the physics program of the Relativistic Heavy-Ion Collider. The STAR Collaboration has previously presented the results of a blind analysis of isobar collisions ( Ru 44 96 + Ru 44 96 , Zr 40 96 + Zr 40 96 ) in the search for the CME. The isobar ratio ( Y ) of CME-sensitive observable, charge separation scaled by elliptic anisotropy, is close to but systematically larger than the inverse multiplicity ratio, the naive background baseline. This indicates the potential existence of a CME signal and the presence of remaining nonflow background due to two- and three-particle correlations, which are different between the isobars. In this postblind analysis, we estimate the contributions from those nonflow correlations as a background baseline to Y , utilizing the isobar data as well as Heavy Ion Jet Interaction Generator simulations. This baseline is found consistent with the isobar ratio measurement, and an upper limit of 10% at 95% confidence level is extracted for the CME fraction in the charge separation measurement in isobar collisions at s NN = 200 GeV. Published by the American Physical Society 2024

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

NASA NTRS1971

Improved wax mold technique forms complex passages in solid structures

Low-cost fabricating technique produces minute, complex air passages in fluidic devices. Air jet interactions in these function as electronic and electromechanical control systems. Wax cores are fabricated without distortion by two-wax process using nonsoluble pattern-wax and water-soluble wax. Significant steps in fabrication process are discussed.

Hellbaum, R. F.↗

NASA NTRS1976

Numerical solution of supersonic three-dimensional free-mixing flows using the parabolic-elliptic Navier-Stokes equations

A numerical method is presented for solving the parabolic-elliptic Navier-Stokes equations. The solution procedure is applied to three-dimensional supersonic laminar jet flow issuing parallel with a supersonic free stream. A coordinate transformation is introduced which maps the boundaries at infinity into a finite computational domain in order to eliminate difficulties associated with the imposition of free-stream boundary conditions. Results are presented for an approximate circular jet, a square jet, varying aspect ratio rectangular jets, and interacting square jets. The solution behavior varies from axisymmetric to nearly two-dimensional in character. For cases where comparisons of the present results with those obtained from shear layer calculations could be made, agreement was good.

Hirsh, R. S.↗

NASA NTRS1976

Study of liquid jet impingement on screens

A model is presented for an unconfined flow, such as a free jet, impinging on a screen which incorporates the influence of liquid deflection by the screen. The boundary layer blockage coefficient is introduced. This coefficient depends on the screen weave geometry and the jet impingement angle, and essentially accounts for the increase in fluid particle trajectory length through the screen resulting from the flow deflection. Comparisons were made with previous experimental studies to determine empirical values of the blockage coefficient. It is concluded that the new model reliably predicts the bulk flow and penetration characteristics of an impinging liquid jet interacting with a screen.

Dodge, F. T.↗

NASA NTRS1978

Flow of liquid jets through closely woven screens

Previously developed analytical models relate pressure drop across a fine-mesh screen to throughflow velocity for duct systems. These models are shown to be unreliable for an unconfined flow, such as a free jet, impinging on a screen. A new model is developed for these kinds of systems, incorporating the important influence of liquid deflection by the screen. A new parameter, the boundary-layer blockage coefficient, is introduced. This coefficient, which depends on the screen weave geometry and the jet impingement angle, accounts for the increase in fluid path length through the screen resulting from the flow deflection. Comparisons are made with previous experimental studies to determine empirical values of the blockage coefficient. It is concluded that the new model reliably predicts the bulk flow and penetration characteristics of an impinging liquid jet interacting with a screen.

Dodge, F. T.↗

NASA NTRS1978

Flow of liquid jets through closely woven screens

Previously developed analytical models relate pressure drop across a fine-mesh screen to throughflow velocity for duct systems. These models are shown to be unreliable for an unconfined flow, such as a free jet, impinging on a screen. A new model is developed for these kinds of systems, incorporating the important influence of liquid deflection by the screen. A new parameter, the boundary layer blockage coefficient, is introduced. This coefficient, which depends on the screen weave geometry and the jet impingement angle, accounts for the increase in fluid path length through the screen resulting from the flow deflection. Comparisons are made with previous experimental studies to determine empirical values of the blockage coefficient. It is concluded that the new model reliably predicts the bulk flow and penetration characteristics of an impinging liquid jet interacting with a screen.

Dodge, F. T.↗

NASA NTRS1981

Advanced turboprop installation aerodynamics

The expected aerodynamic effects of a propfan installed on a thick supercritical wing are summarized qualitatively. Nacelle/wing and jet interactions, slipstream incremental velocity, nonuniform inflow, and swirl loss recovery are discussed.

Smith, R. C.↗

NASA NTRS1982

Aerodynamic comparisons of STS-1 Space Shuttle entry vehicle

A conventional flight-test program, which slowly and cautiously approaches more severe flight conditions, was not possible with the Orbiter. On the first flight, the Orbiter entered the atmosphere at Mach 28 and decelerated through the Mach range. (The subsonic portion of flight was also flown by another orbiter vehicle during the Approach and Landing Test Program.) Certification for the first flight was achieved by an extensive wind-tunnel test and analysis program and by restricting the flight maneuvers severely. The initial flights of the orbiter were heavily instrumented for the purpose of obtaining accurate aerodynamic data. Even without maneuvers to excite the system, the first flight provided comparisons between flight and wind-tunnel-derived predicted data in the areas of aerodynamic performance, longitudinal trim, and reaction-control jet interaction. The aerodynamic performance comparisons are presented.

Young, J. C.↗

NASA NTRS1985

Optical interferometry in fluid dynamics research

Optical interferometry techniques have been applied to the investigation of transonic airfoil flow fields in large-scale wind tunnels. Holographic interferometry techniques were used in the study of two-dimensional symmetric NACA 64A010 and Douglas Aircraft Company DSMA671 supercritical airfoil performance in the NASA Ames 2 ft x 2 ft transonic wind tunnel. Quantitative data obtained from the interferograms were compared to the surface pressure data. The excellent agreement obtained verified the accuracy of the flow visualization and demonstrated the potential for acquiring quantitative scalar results. Measurements of the inviscid flow speed and the boundary layer and wake velocity profiles were extracted from the interferograms and compared to laser Doppler velocimeter measurements. These results were also in good agreement. A method for acquiring real-time interferometric data in large-scale facilities was developed. This method, based on the point diffraction interferometer, was successfully tested in the Ames 2 ft x 2 ft transonic wind tunnel. The holographic and real-time interferometry methods were applied to the investigations of circulation control airfoils utilizing the Coanda effect. These results revealed the details of the jet interaction with the trailing edge boundary layer and the other parameters affecting the lift augmentation.

Bachalo, W. D.↗

NASA NTRS1987

Optical interferometry in fluid dynamics research

Optical interferometry techniques were applied to the investigation of transonic airfoil flow fields in large wind tunnels. Holographic interferometry techniques were used to study 2 dimensional symmetric NACA 64A010 and Douglas Aircraft Co. DSMA671 supercritical airfoil performance in the NASA Ames 2 x 2 ft transonic wind tunnel. Quantitative data obtained from the interferograms were compared to the surface pressure data. The agreement obtained verified the accuracy of the flow visualization and demonstrated the potential for acquiring quantitative scalar results. Measurements of the inviscid flow speed and the boundary layer and wake velocity profiles were extracted from the interferograms and compared to laser Doppler velocimeter measurements. These results were also in good agreement. A method for acquiring real time interferometric data in large scale facilities was developed. This method, based on the point diffraction interferometer, was successfully tested in the 2 x 2 ft transonic wind tunnel. The holographic and real time interferometry methods were applied to the investigations of circulation control airfoils utilizing the Coanda effect. These results reveals the details of the jet interacting with the trailing edge boundary layer and the other parameters affecting the lift augmentation.

Bachalo, W. D.↗

NASA NTRS1986

Recent advances in aerodynamics

Papers are presented on unsteady transonic aerodynamics and aeroelasticity, the unsteady separation phenomenon, and a wind tunnel method for V/STOL testing. Also considered are vortex-edge interactions, jet instability theory, large-scale organized motions in jets and shear layers, and the evolution of adaptive-wall wind tunnels. Other topics include advances in ejector thrust augmentation, multiple jet impingement flowfields, and recent advances in prediction methods for jet-induced effects on V/STOL aircraft.

Krothapalli, A.↗