Engineering Papers⌕ Search

Engineering topics

Zhou, Y.

Publications and source records attributed to Zhou, Y..

At least 55 records · Page 3

Luminescent Properties of Borosilicate Glass Doped with Cerium

ABS–BGP glasses (Al{sub 2}O{sub 3}–B{sub 2}O{sub 3}–SiO{sub 2}–BaCO{sub 3}–Gd{sub 2}O{sub 3}–P{sub 2}O{sub 5}) doped with different concentrations of Ce{sup 3+} ions are synthesized by the high-temperature melting technique. Optical, structural, and luminescence properties were studied. Emission connected with the transitions of Ce{sup 3+} ions is recorded in a spectral region of 350–550 nm. The luminescence decay kinetics is characterized by two components: fast and slow. The fast decay component is 45–90 ns; decreasing decay time of the slow component from 4 to 0.9 μs is observed with increasing cerium ion concentration. Based on the obtained results, it is assumed that Ce{sup 3+} ions exist in different emission states in the borosilicate glass.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

On the evolution of microstructure and defect control in 316L SS components fabricated via directed energy deposition

To identify the critical issues that affect the evolution of microstructure during additive manufacturing, we investigated the influence of process parameters on the evolution of the dimensional and surface quality, microstructure, internal defects, and mechanical properties in 316L stainless steel (SS) components fabricated using laser engineered net shaping (LENS®), a directed energy deposition (DED) additive manufacturing (AM) technique. The results show that the accumulation of un-melted powder particles on the side walls of deposited sections can be avoided by selecting a laser under-focused condition. Moreover, we report that the variation of melt pool width is more sensitive to laser power than to the depth of the melt pool. The formation of a so-called “hierarchical” microstructure with cellular morphology is attributable to a combination of layer deposition and rapid solidification, which are characteristics of AM. Finally, we discuss microstructure evolution and defect formation, particularly the formation of multiple interfaces and the presence of un-melted powder particles and pores, in light of the dynamic convective fluid flow and rapid solidification that occur in the melt pool. X-ray computed tomography (X-CT) was used to precisely map the spatial distribution of pores in the DED components. The evolution of microstructure during DED is discussed in the context of related thermal phenomena in an effort to provide fundamental insight into the mechanisms that govern defect formation.

36 MATERIALS SCIENCE↗

Quasioptical modeling of wave beams with and without mode conversion. I. Basic theory

This work opens a series of papers where we develop a general quasi-optical theory for mode-converting electromagnetic beams in plasma and implement it in a numerical algorithm. Here, the basic theory is introduced. We consider a general quasimonochromatic multicomponent wave in a weakly inhomogeneous linear medium with no sources. For any given dispersion operator that governs the wave field, we explicitly calculate the approximate operator that governs the wave envelope ψ to the second order in the geometrical-optics parameter. Then, we further simplify this envelope operator by assuming that the gradient of ψ transverse to the local group velocity is much larger than the corresponding parallel gradient. This leads to a parabolic differential equation for ψ (“quasioptical equation”) on the basis of the geometrical-optics polarization vectors. Scalar and mode-converting vector beams are described on the same footing. Here, we also explain how to apply this model to electromagnetic waves in general. In the next papers of this series, we report successful quasioptical modeling of radio frequency wave beams in magnetized plasma based on this theory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Overview of HOMEChem: House Observations of Microbial and Environmental Chemistry

The House Observations of Microbial and Environmental Chemistry (HOMEChem) study is a collaborative field investigation designed to probe how everyday activities influence the emissions, chemical transformations and removal of trace gases and particles in indoor air. Sequential and layered experiments in a research house included cooking, cleaning, variable occupancy, and window-opening. This paper describes the overall design of HOMEChem and presents preliminary case studies investigating the concentrations of reactive trace gases, aerosol particles, and surface films. Cooking was a large source of VOCs, CO 2 , NO x , and particles. By number, cooking particles were predominantly in the ultrafine mode. Organic aerosol dominated the submicron mass, and, while variable between meals and throughout the cooking process, was dominated by components of hydrocarbon character and low oxygen content, similar to cooking oil. Air exchange in the house ensured that cooking particles were present for only short periods. During unoccupied background intervals, particle concentrations were lower indoors than outdoors. The cooling coils of the house ventilation system induced cyclic changes in water soluble gases. Even during unoccupied periods, concentrations of many organic trace gases were higher indoors than outdoors, consistent with housing materials being potential sources of these compounds to the outdoor environment. Organic material accumulated on indoor surfaces, and exhibited chemical signatures similar to indoor organic aerosol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Liquid metal embrittlement in laser lap joining of TWIP and medium-manganese TRIP steel: The role of stress and grain boundaries

Highlights: • This work shows liquid metal embrittlement in externally loaded laser lap welding. • Results confirmed a direct relation between external load and LME susceptibility. • TWIP steel showed a higher LME susceptibility compared to medium-Mn TRIP steel. • Results indicated stress-assisted diffusion of Zn into austenite grain boundaries. • High angle grain and Σ3 twinning boundaries play major role in Zn penetration. - Abstract: High-Manganese austenite-containing steels with superior combination of strength and ductility have shown potential for enhancement of passenger safety and body-in-white (BIW) weight reduction. Even though Zn-coated austenitic steels have improved corrosion resistance, they are highly susceptible to liquid metal embrittlement (LME) during welding. The present work is aimed to address LME susceptibility during restrained laser lap joining of high-Mn twinning induced plasticity (TWIP) and medium-Mn transformation induced plasticity (MMn-TRIP) steels. Electron probe micro-analysis (EPMA) results showed that stress-assisted diffusion of Zn into the austenite grain boundaries and further liquid Zn formation by a peritectic reaction lead to grain boundary decohesion. Electron backscatter diffraction (EBSD) results demonstrated that high angle and special grain boundaries are prone to Zn-penetration within the heat-affected-zone (HAZ). Additionally, LME sensitivity was observed to be highly dependent on the magnitude of applied stress.

36 MATERIALS SCIENCE↗

Surface Modification of 304 Stainless Steel by Electro-Spark Deposition

Electro-spark deposition (ESD) is a pulsed microwelding process that is used to apply surface coatings for the repair of damaged high value and precision products or modify their surfaces for specific properties. The low heat input, minimal heat-affected zone and the ability to form metallurgical bonding of coating to substrate are major advantages of the ESD process. Many applications require the components to have excellent surface performance, such as wear and corrosion resistance. ESD technique provides an approach to modify the component surface without compromising the bulk properties. In this study, surface modifications of 304 stainless steel by ESD were investigated. Titanium carbide (TiC), tungsten carbide (WC) and molybdenum (Mo) were employed as coating materials. Scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDX) analysis were conducted to characterize the microstructure and composition of the coatings. The coatings thicknesses were all around 40 µm. The results showed that TiC and WC coatings showed a dramatic increase in the microhardness, up to 5 times. WC coating improved the wear resistance by more than 5 times, while TiC and Mo coatings also improved it by approximately 2.5 times. Electro-chemical tests were conducted to investigate the corrosion resistance of the coatings. Mo coating exhibited a significant improvement in the corrosion resistance in 5% NaCl solutions, corroding 350 times slower than stainless steel. Synchrotron x-ray diffraction was performed to investigate the microstructure changes of the Mo-coated sample. Heat treatment was also carried out to investigate the corrosion behavior of Mo-coated 304 stainless steel at elevated service temperature in air or argon.

36 MATERIALS SCIENCE↗

A comparison of He and Ne FIB imaging of cracks in microindented silicon nitride

Highlights: • Silicon nitride was successfully imaged with helium and neon ion microscopy. • Indent-induced cracking was resolved on conductively-coated and uncoated samples. • Cracking was found to be primarily intergranular in nature. • The grain microstructure was most visible on the carbon-coated sample. • For the carbon-coated sample, localized charging was observed along crack pathways. - Abstract: Helium ion microscopy (HIM) offers potential as a high spatial resolution technique for imaging insulating samples that are susceptible to charging artifacts. In this study helium and neon ion microscopy are used to image cracking in microindented samples of the non-conductive ceramic silicon nitride. The crack morphology of radial cracks emanating from the microindentations has been characterized for two different compositions of silicon nitride, with and without conductive coatings. Gold coating enhances crack edge contrast, but masks grain contrast for both He and Ne ion-induced secondary electron (ISE) imaging. Carbon coating enables the crystalline and glassy phases to be distinguished, more clearly with Ne-ISE, and the cracking pathway is found to be primarily intergranular. Zones of <100 nm diameter depleted ion-induced secondary electron emission along the crack paths are identified, consistent with charging ‘hotspots’.

36 MATERIALS SCIENCE↗

Late-time growth rate, mixing, and anisotropy in the multimode narrowband Richtmyer–Meshkov instability: The θ-group collaboration

Turbulent Richtmyer–Meshkov instability (RMI) is investigated through a series of high resolution three-dimensional simulations of two initial conditions with eight independent codes. The simulations are initialised with a narrowband perturbation such that instability growth is due to non-linear coupling/backscatter from the energetic modes, thus generating the lowest expected growth rate from a pure RMI. By independently assessing the results from each algorithm and computing ensemble averages of multiple algorithms, the results allow a quantification of key flow properties as well as the uncertainty due to differing numerical approaches. A new analytical model predicting the initial layer growth for a multimode narrowband perturbation is presented, along with two models for the linear and non-linear regimes combined. Overall, the growth rate exponent is determined as θ=0.292±0.009, in good agreement with prior studies; however, the exponent is decaying slowly in time. Also, θ is shown to be relatively insensitive to the choice of mixing layer width measurements. The asymptotic integral molecular mixing measures Θ=0.792±0.014, Ξ=0.800±0.014, and Ψ=0.782±0.013 are lower than some experimental measurements but within the range of prior numerical studies. The flow field is shown to be persistently anisotropic for all algorithms, at the latest time having between 49% and 66% higher kinetic energy in the shock parallel direction compared to perpendicular and does not show any return to isotropy. The plane averaged volume fraction profiles at different time instants collapse reasonably well when scaled by the integral width, implying that the layer can be described by a single length scale and thus a single θ. In conclusion, quantitative data given for both ensemble averages and individual algorithms provide useful benchmark results for future research.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nucleation and growth kinetics for intercalated islands during deposition on layered materials with isolated pointlike surface defects

Theory and stochastic lattice-gas modeling is developed for the formation of intercalated metal islands in the gallery between the top layer and the underlying layer at the surface of layered materials. Our model for this process involves deposition of atoms, some fraction of which then enter the gallery through well-separated pointlike defects in the top layer. Subsequently, these atoms diffuse within the subsurface gallery leading to nucleation and growth of intercalated islands nearby the defect point source. For the case of a single point defect, continuum diffusion equation analysis provides insight into the nucleation kinetics. However, complementary tailored lattice-gas modeling produces a more comprehensive and quantitative characterization. We analyze the large spread in nucleation times and positions relative to the defect for the first nucleated island. We also consider the formation of subsequent islands and the evolution of island growth shapes. The shapes reflect in part our natural adoption of a hexagonal close-packed island structure. As a result, motivation and support for the model is provided by scanning tunneling microscopy observations of the formation of intercalated metal islands in highly-ordered pyrolytic graphite at higher temperatures.

36 MATERIALS SCIENCE↗

A platform for studying the Rayleigh–Taylor and Richtmyer–Meshkov instabilities in a planar geometry at high energy density at the National Ignition Facility

A new experimental platform has been developed at the National Ignition Facility (NIF) for studying the Rayleigh–Taylor (RT) and Richtmyer–Meshkov (RM) instabilities in a planar geometry at high-energy-densities. The platform uses 60 beams of the NIF laser to drive an initially solid shock tube containing a pre-machined interface between dense and light materials. The strong shock turns the initially solid target into a plasma and the material boundary into a fluid interface with the imprinted initial condition. The interface evolves by action of the RT and RM instabilities, and the growth is imaged with backlit x-ray radiography. We present our first data involving sinusoidal interface perturbations driven from the heavy side to the light side. Late-time radiographic images show the initial conditions reaching the deeply nonlinear regime, and an evolution of fine structure consistent with a transition to turbulence. Lastly, we show preliminary comparisons with post-shot numerical simulations and discuss the implications for future campaigns.

36 MATERIALS SCIENCE↗

Secondary phases in Al x CoCrFeNi high-entropy alloys: An in-situ TEM heating study and thermodynamic appraisal

Secondary phases, either introduced by alloying or heat treatment, are commonly present in most high-entropy alloys (HEAs). Understanding the formation of secondary phases at high temperatures, and their effect on mechanical properties, is a critical issue that is undertaken in the present paper, using the Al x CoCrFeNi (x = 0.3, 0.5, and 0.7) as a model alloy. The in-situ transmission-electron-microscopy (TEM) heating observation, an atom-probe-tomography (APT) study for the reference starting materials (Al 0.3 and Al 0.5 alloys), and thermodynamic calculations for all three alloys, are performed to investigate (1) the aluminum effect on the secondary-phase fractions, (2) the annealing-twinning formation in the face-centered-cubic (FCC) matrix, (3) the strengthening effect of the secondary ordered body-centered-cubic (B2) phase, and (4) the nucleation path of the σ secondary phase thoroughly. Finally, the present work will substantially optimize the alloy design of HEAs and facilitate applications of HEAs to a wide temperature range.

36 MATERIALS SCIENCE↗

Vaporization behavior of tetraoctylphosphonium bis(2-ethylhexyl)phosphate ionic liquid

We determined the equilibrium vapor pressures, p e , of the ionic liquid tetraoctylphosphonium bis(2-ethylhexyl)phosphate ([P 8888 ][DEHP]) over the temperature range 409–495 K using mass loss Knudsen effusion. The p e versus temperature relationship compares well to 1-methyl-3-octylimidazolium bis(trifluoromethylsulfonyl)imide ([C 8 mim][NTf 2 ]) but is lower than that of 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C 2 mim][NTf 2 ]) when measured using the same technique. Here, we determined the discrepancies between the p e for [C 8 mim][NTf 2 ] and [C 2 mim][NTf 2 ] with previous studies is discussed. Finally, the enthalpy and entropy of vaporization for all three fluids are estimated from the Clasius-Clapeyron relation.

36 MATERIALS SCIENCE↗

An Assessment of Causes of PEV Success Across U.S. Metro Areas

Using 2014 U.S. light duty PEV registrations by make and model, this paper assesses the causes of Plug-in Electric Vehicle (PEV) success across U.S. states focusing on areas that had incentive and utility programs supporting PEV adoption. Market segments investigated were (1) luxury/performance (>$60,000 list price), (2) mid-market ($40-50,000), (3) mass market (<$40.000), and (4) total. States with either exclusive or preferential BEV incentives are a focus. BEV-biased incentives proved to be very effective in promoting mass market BEVs. After controlling for these attributes, case studies for several utility service areas were conducted to gauge whether PEVs were more or less successfully implemented via outreach by those utilities. These investigations suggest ways that utilities can successfully increase PEV registrations, after taking local climate and state incentives into consideration.

Zhou, Y.↗

Tuning carrier density at complex oxide interface with metallic overlayer

We have systematically investigated the electronic transport properties of the LaAlO{sub 3}/SrTiO{sub 3} interfaces with several different metal capping layers. The sheet carrier density can be tuned in a wide range by the metallic overlayer without changing the carrier mobility. The sheet carrier density variation is found to be linearly dependent on the size of metal work function. This behavior is explained by the mechanism of the charge transfer between the oxide interface and the metal overlayer across the LaAlO{sub 3} layer. Our results confirm the existence of a built-in electric field in LaAlO{sub 3} film with an estimated value of 67.7 eV/Å. Since the metallic overlayer is essential for devices, the present phenomena must be considered for future applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗