Engineering Papers⌕ Search

Engineering topics

Yoo, H. I.

Publications and source records attributed to Yoo, H. I..

17 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Characterization of CdS/CdTe and CdS/CuInSe2 thin film solar cells

A study on low cost polycrystalline thin film CdS/CdTe and CdS/CuInSe2 solar cells using measurements of spectral response and capacitance-voltage-frequency relationships was performed. Because of high concentrations of localized levels in the energy gap existing in materials and at interfaces, the redistribution of charge among the levels due to illumination plays an important role in the collection of light-generated current in these cells. The results illustrate some related phenomena observed in these cells.

Cheng, L. J.↗
NASA NTRS1982

Field experience with various slicing methods

Wafer slicing using internal diameter (ID) saw, multiblade slurry (MBS) saw and multiwire slurry (MWS) saw techniques were evaluated. Wafer parameters such as bow, taper, and roughness which may not be important factors for solar cell fabrication, were considerably better for ID saw than those of the MBS and MWS saw. Analysis of add-on slicing cost indicated that machine productivity seems to be a major limiting factor for ID saw, while expendible material costs are a major factor for both MBS and MWS saw. Slicing experience indicated that the most important factors controling final wafer cost are: (1) silicon cost (wafer thickness + kerf loss); (2) add-on slicing cost, and (3) mechanical yield. There is a very strong interaction between these parameters, suggesting a necessity of optimization of these parameters.

Yoo, H. I.↗
NASA NTRS1981

Silicon solar cell process development, fabrication, and analysis

Work has progressed in fabrication and characterization of solar cells from ubiquitous crystallization process (UCP) wafers and LASS ribbons. Gettering tests applied to UCP wafers made little change on their performance compared with corresponding baseline data. Advanced processes such as shallow junction (SJ), back surface field (BSF), and multilayer antireflection (MLAR) were also applied. While BSF by Al paste had shunting problems, cells with SJ and BSF by evaporated Al, and MLAR did achieve 14.1% AMI on UCP silicon. The study of LASS material was very preliminary. Only a few cells with SJ, BSR, (no BSF) and MLAR were completed due to mechanical yield problems after lapping the material. Average efficiency was 10.7% AMI with 13.4% AMI for CZ controls. Relatively high minority carrier diffusion lengths were obtained. The lower than expected Jsc could be partially explained by low active area due to irregular sizes.

Yoo, H. I.↗
NASA NTRS1981

Silicon solar cell process development, fabrication and analysis

Solar cells were fabricated from EFG ribbons dendritic webs, cast ingots by heat exchanger method, and cast ingots by ubiquitous crystallization process. Baseline and other process variations were applied to fabricate solar cells. EFG ribbons grown in a carbon-containing gas atmosphere showed significant improvement in silicon quality. Baseline solar cells from dendritic webs of various runs indicated that the quality of the webs under investigation was not as good as the conventional CZ silicon, showing an average minority carrier diffusion length of about 60 um versus 120 um of CZ wafers. Detail evaluation of large cast ingots by HEM showed ingot reproducibility problems from run to run and uniformity problems of sheet quality within an ingot. Initial evaluation of the wafers prepared from the cast polycrystalline ingots by UCP suggested that the quality of the wafers from this process is considerably lower than the conventional CZ wafers. Overall performance was relatively uniform, except for a few cells which showed shunting problems caused by inclusions.

Yoo, H. I.↗
NASA NTRS1981

Silicon solar cell process development, fabrication, and analysis

Two large cast ingots were evaluated. Solar cell performance versus substrate position within the ingots was obtained and the results are presented. Dendritic web samples were analyzed in terms of structural defects, and efforts were made to correlate the data with the performance of solar cells made from the webs.

Yoo, H. I.↗
NASA NTRS1981

Current status of solar cell performance of unconventional silicon sheets

It is pointed out that activities in recent years directed towards reduction in the cost of silicon solar cells for terrestrial photovoltaic applications have resulted in impressive advancements in the area of silicon sheet formation from melt. The techniques used in the process of sheet formation can be divided into two general categories. All approaches in one category require subsequent ingot wavering. The various procedures of the second category produce silicon in sheet form. The performance of baseline solar cells is discussed. The baseline process included identification marking, slicing to size, and surface treatment (etch-polishing) when needed. Attention is also given to the performance of cells with process variations, and the effects of sheet quality on performance and processing.

Yoo, H. I.↗
NASA NTRS1981

Improved performance from solar cells made from candidate sheet silicon materials

Performance of solar cells made from various candidate silicon sheets is updated and the results are presented. Solar cells were fabricated using a baseline process and other process variations, and tested under AM1 conditions. Performance of the baseline solar cells indicates that remarkable improvements in material quality have been achieved for most of the sheets, showing efficiencies close to that of the control cells made from conventional CZ silicon. Process variations (or additions), in general, have resulted in significant improvements in all performance with a degree of change dependent on the process chosen and to a certain extent the sheet quality.

Yoo, H. I.↗
NASA NTRS1980

Silicon solar cell process development, fabrication, and analysis

Solar cells from HEM, Dendritic Webs, and EFG ribbons were fabricated and characterized. The HEM solar cells showed only slight enhancement in cell performance after gettering steps (diffusion glass) were added. Dendritic webs from various growth runs indicated that performance of solar cells made from the webs was not as good as that of the conventional CZ cells. The EFG ribbons grown in CO ambient showed significant improvement in silicon quality.

Yoo, H. I.↗
NASA NTRS1979

Silicon Solar Cell Process Development, Fabrication and Analysis, Phase 1

Solar cells from RTR ribbons, EFG (RF and RH) ribbons, dendritic webs, Silso wafers, cast silicon by HEM, silicon on ceramic, and continuous Czochralski ingots were fabricated using a standard process typical of those used currently in the silicon solar cell industry. Back surface field (BSF) processing and other process modifications were included to give preliminary indications of possible improved performance. The parameters measured included open circuit voltage, short circuit current, curve fill factor, and conversion efficiency (all taken under AM0 illumination). Also measured for typical cells were spectral response, dark I-V characteristics, minority carrier diffusion length, and photoresponse by fine light spot scanning. the results were compared to the properties of cells made from conventional single crystalline Czochralski silicon with an emphasis on statistical evaluation. Limited efforts were made to identify growth defects which will influence solar cell performance.

Yoo, H. I.↗
NASA NTRS1979

Silicon Solar Cell Process Development, Fabrication and Analysis

The standard solar cells (2x2 cm) from the cast silicon (HEM) showed a maximum AMO efficiency of 10.1%. Cells from the low resistivity material (0.5 ohm-cm) showed lower performance than those of the high resistivity cast silicon (3 ohm-cm), an average efficiency 9.5% versus 7.6%. Maximum AMO efficiency of the standard solar cells from the EFG (RH) ribbons was about 7.5%. The solar cells from the controlled SiC, using the displaced die, showed more consistent and better performance than those of the uncontrolled SiC ribbons, an average efficiency of 6.6% versus 5.4%. The average AMO efficiency of the standard SOC solar cells were about 6%. These were large area solar cells (an average area of 15 sq cm). A maximum efficiency of 7.3% was obtained. The SOC solar cells showed both leakage and series resistance problems, leading to an average curve fill factor of about 60%.

Yoo, H. I.↗
NASA NTRS1979

Silicon Solar Cell Process Development, Fabrication and Analysis

The standard solar cells (2x2 cm) from the cast silicon heatexchanger method) showed a maximum AMO efficiency of 10.1%. Cells from low resistivity material (0.5 ohm-cm) showed lower performance than those of the high resistivity cast silicon (3 ohm-cm), an average efficiency 9.5% versus 7.6% Maximum AMO efficiency of the standard solar cells (2x2 cm) from the EFG (RH) ribbons was about 7.5%. The solar cells from controlled SiC, using the displaced die, showed more consistent and better performance than those of the uncontrolled SiC ribbons, an average efficiency of 6.6% versus 5.4% The average AMO efficiency of the standard silicon ceramic (soc) solar calls were about 6%. These were large area solar cells (an average area of 15 sq cm). A maximum efficiency of 7.3% was obtained. The SOC solar cells showed both leakage and series resistance problems, leading to an average curve fill factor of about 60%.

Yoo, H. I.↗
NASA NTRS1978

Silicon Solar Cell Process Development, Fabrication and Analysis

Ribbon to Ribbon (RTR) solar cells processed from polycrystalline feedstock showed maximum AMO efficiency of 5.6%. Solar cells from single crystalline feedstock showed slightly higher efficiency than those from polycrystalline feedstock, indicating maximum efficiency of about 6.6% with SiO AR coating. Single crystalline control cells gave 11-12% AMO efficiencies demonstrating that the poor performance of the RTR solar was due to the low quality of material itself. Dendritic web solar cells from the standard process showed maximum AMO efficiency of 9.8% while efficiency of control solar cells were around 11-12%. Web solar cells from back surface field (BSF) process indicated maximum AMO efficiency of 10.9%. Some improvement in open circuit voltage was noticed from the BSF process. Small light spot scanning experiments were carried out on the solar cells from Wacker Silso, EFG, RTR, and dendritic web ribbons. Photoresponse results provided information on localized cell performance and grain size in polycrystalline material, and agreed quite well with the cell performance data, such as efficiency, minority carrier diffusion length, and spectral response.

Yoo, H. I.↗
NASA NTRS1978

Silicon solar cell process. Development, fabrication and analysis

Solar cells were fabricated from unconventional silicon sheets, and the performances were characterized with an emphasis on statistical evaluation. A number of solar cell fabrication processes were used and conversion efficiency was measured under AMO condition at 25 C. Silso solar cells using standard processing showed an average efficiency of about 9.6%. Solar cells with back surface field process showed about the same efficiency as the cells from standard process. Solar cells from grain boundary passivation process did not show any improvements in solar cell performance.

Yoo, H. I.↗
NASA NTRS1977

Assessment of present state-of-the-art sawing technology of large diameter ingots for solar sheet material

The objective of this program is to assess the present state-of-the-art sawing technology of large diameter silicon ingots (3 inch and 4 inch diameter) for solar sheet materials. During this period, work has progressed in three areas: (1) slicing of the ingots with the multiblade slurry saw and the I.D. saw, (2) characterization of the sliced wafers, and (3) analysis of direct labor, expendable material costs, and wafer productivity.

Yoo, H. I.↗