Engineering Papers⌕ Search

Engineering topics

Yi Lin

Publications and source records attributed to Yi Lin.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Using Holey Graphene for Improved Interfacial Contact in Solid Electrolyte Ionic Conductivity Measurements

Solid-state batteries (SSBs) are poised to become the batteries of the future with advantages such as higher energy density, lighter weight, versatile geometry, and greater safety due to low flammability risk. An important parameter of the solid electrolyte (SE) used is its ionic conductivity. The ionic conductivity is generally calculated from the bulk resistance of a SE pellet, measured from the electrochemical impedance spectroscopy data. The SE pellet is typically prepared from the electrolyte powder by dry compression and is sandwiched between two blocking current collectors to obtain the impedance spectroscopy data. One of the challenges in conducting this measurement is poor interfacial contacts between the SE pellet and the current collector surfaces. Therefore, measurements reported in the literature may underestimate the true ionic conductivity of a given electrolyte. Holey graphene is a carbon nanomaterial with high electrical conductivity and unique dry compressibility, which is unusual for carbon materials but similar to many oxide and sulfide SEs. In this work, it is demonstrated that adding a thin layer of holey graphene between the electrolyte and the stainless steel current collectors significantly improves the interfacial contact. The ionic conductivity values obtained in the effort were sometimes several times higher than the data measured for SEs without the holey graphene layers. This work calls for more standardized measurement procedures to reduce the discrepancies in reported ionic conductivity values.

Solid state battery↗
NASA NTRSDate not supplied

Next Generation Batteries for Electric Aviation and Space

Energy storage plays a critical part in the success of future NASA missions that desire batteries with higher energy density, higher power, and most critically improved safety. These performance requirements stretch beyond that of electric automobile markets and are required for enabling widespread adoption of electric aviation. One approach to improve the safety and energy is the transition to non-volatile solid-state electrolytes (SSE) which promise many advantages over traditional flammable liquid electrolytes and may also be an enabling technology for next generation chemistries such as lithium-sulfur (Li-S). However, significant manufacturing challenges must be overcome before the adoption of such technology. This study will discuss the development of solid electrolytes specifically designed to meet future NASA electric aviation targets with densified thicknesses between 20-30 microns derived using solvent processing techniques. Films were produced 10-15 times thinner than comparable bulk cold pressed powder electrolytes and achieved thicknesses comparable to commercial polyolefin separators (25 micron) used in commercial liquid containing lithium-ion cells. Furthermore, design and development of novel cathode composites through integration of experiment and a particle dynamics model will be discussed. Beyond aeronautics, unique challenges and requirements exist for energy storage for space applications, which can cover extreme temperatures and material scarcity for in-situ derived materials. Additionally, this talk will briefly cover the need and development of lunar and Martian derived electrode materials for in-situ manufacturing of energy storage devices.

Batteries↗
NASA NTRSDate not supplied

Solid-state Architecture Batteries for Enhanced Rechargeability and Safety (SABERS) Beyond Li-Ion: Technology to Enable Sustainable Electric Aviation

All-electric and hybrid electric aerovehicle concepts face numerous technical barriers prior to their introduction into the consumer marketplace in order to meet sustainable aviation goals. One of the primary barriers to overcome is developing an energy dense storage system capable of meeting the rigorous aerospace safety and performance criteria. Additionally, the electric aviation market requires that the batteries be fabricated in a sustainable manner with materials that are readily available and abundant within the U.S. to ensure there are no supply chain issues during manufacturing. The performance metrics to enable electric aviation are at least two times greater than those of electric ground vehicles. Furthermore, inherently non-flammable batteries are essential for safe operation of commercial electric aerovehicles. The SABERS concept proposes a battery that meets the key performance criteria through development of a solid-state architecture battery utilizing high-capacity sulfur-selenium cathode and lithium metal anode. The combination of sulfur and selenium offers a balanced energy-to-power density ratio, which can be tailored to the specific application by altering the stoichiometric ratios of sulfur to selenium. The hybrid cathode has been developed by implementing NASA patented holey graphene technology as a highly conductive, ultra-lightweight electrode scaffold. A solid-state electrolyte has been used as a safe, non-flammable replacement to the highly flammable liquid organic electrolytes currently used in SOA lithium-ion batteries. This solid-state lithium-sulfur/selenium cell will be designed into a serial stacking configuration to enable dense packaging of the battery cells. The serial stacking configuration is termed a bipolar stack, which has the advantages of reducing overall cell weight, simplifying the interfaced connections for the cell, and minimizing the cooling requirements. Lastly, optimization of battery components will occur through a robust and rigorous combination of various computational modeling techniques covering multiple length scales. The expected result will be a fully solid-state battery with operational temperatures up to 150 °C which provides the required energy density, discharge rates, and inherent safety to meet the strict aerospace mission performance criteria. This poster summarizes recent results from battery component optimization to scale-up production of full SABERS pouch cells.

Urban Air Mobility (UAM) Vehicles↗
NASA NTRSDate not supplied

Elastic-Poroelastic Simulation of Locally Resonant Ultrasound for Aging Li-Metal Batteries

An elastic-poroelastic simulation of ultrasound inspection for lithium-metal batteries is presented and compared to empirical reflection spectra measured during battery cycling. Simulated reflection spectra were obtained using a two-dimensional (2D) plane strain model, comprised of dozens of individual microns-thick layers within a Li-metal pouch cell. The simulated reflection spectra were then compared to ultrasonic reflection spectra measurements taken intermittently during cell cycling. A sensitivity analysis and parameter calibration were performed for the pristine pouch cell simulation prior to cycling, providing a baseline to account for difficult to measure poroelastic material parameters. Then, the reduction in solid Li anode thickness and corresponding growth into a mossy lithium layer was modeled to represent aging conditions. Results from both simulations and empirical inspections show similar trends in through-thickness resonance frequencies due to cell aging.

Battery↗
NASA NTRSDate not supplied

Fabricating Solid-State Batteries for Electric Aviation

All-solid-state lithium batteries are widely reputed as the next major step in energy storage technology on account their drastically improved safety over wet cells, as solid electrolytes lack the volatile compounds in wet electrolytes that make them combustible. This enhanced safety enables a far wider range of products and vehicles to go fully electric and aligns with future NASA missions that require high performing, reliable, and safe batteries. However, they currently face issues with implementation in consumer products due to the often-poor mechanical properties of the solid electrolyte and relative difficulty to manufacture. Typical solid-state electrolyte challenges were bypassed by incorporating a range of polymeric binders into a solid electrolyte suspension and cast onto a composite carbon-sulfide cathode to create a single bilayer film. The resulting films display superior flexibility and durability compared to solid-electrolyte films typically discussed in literature without compromising the thinness of the films. The bilayer film was then punched into 12.7 cm diameter discs and 4 cm by 5 cm sheets, pressed, and assembled into coin cells and pouch cells respectively.

Batteries↗
NASA NTRSDate not supplied

Cathode Modeling of Solid-State Batteries

The search for safe, reliable, and compact high-capacity energy storage devices has led to increased interest in all-solid-state battery research. The use of solid electrolytes provides enhanced safety and durability due to their reduced flammability and increased mechanical strength compared to organic liquid electrolytes. Still, the use of solid electrolytes remains challenging. Computational modeling plays a substantial role in addressing these challenges. A particle dynamics electromechanical model for simulating electrochemical processes in a solid-state battery cathode will be presented. The model presents cathode microstructure at the particle level as a mixture of ionically conductive solid electrolyte particles, electrically conductive carbon additives, and cathodic reactant particles. After densification, the particle connectivity is analyzed to reconstruct the complex electric network connecting reactant particles with an anodic and cathodic current collectors through the electrolyte and carbon particles. The Kirchhoff’s matrix equation describing this electric network, is solved to obtain values of various critical parameters, such as the overall conductivity of the cathode for lithium ions and electrons, cathodic reactant material utilization, and the distribution of the electric current and voltages within the cathode. In addition, by representing the reactant particles as electrolyte or galvanic microcells governed by the Butler-Volmer electrochemical equation, the overall performance of battery cells during charge or discharge processes, respectively, can be predicted for a given cathodic powder composition. The presented model, executed on a high-performance computing architecture, essentially provides a valuable guidance in designing and developing future solid-state batteries.

solid-state battery↗
NASA NTRSDate not supplied

Solid-State Architecture Batteries for Enhanced Rechargeability and Safety (SABERS) Beyond Li-Ion: Technology to Enable Next-Generation Sustainable Electric

All-electric vertical take-off and landing vehicles (eVTOL) for urban air mobility (UAM) concepts face numerous challenging technical barriers before their introduction into the consumer marketplace. The primary barrier to overcome is developing an energy storage system that meets rigorous aerospace safety and performance criteria. The performance metrics for eVTOL vehicles are at least two times greater than those of electric ground vehicles. Furthermore, inherently non-flammable batteries are essential for the safe operation of commercial electric aero vehicles. The SABERS concept proposes a battery that meets the critical performance criteria by developing a solid-state architecture battery utilizing a high-capacity sulfur-selenium cathode and lithium metal anode. The combination of sulfur and selenium offers a balanced energy-to-power density ratio, which can be tailored to the specific application by altering the stoichiometric ratios of sulfur to selenium. This hybrid cathode will be developed using NASA-patented holey graphene technology as a highly conductive, ultra-lightweight electrode scaffold. A solid-state electrolyte will be used as a safe, non-flammable replacement for the highly flammable liquid organic electrolytes currently in SOA lithium-ion batteries. This solid-state lithium-sulfur/selenium cell will be designed in a serial stacking configuration to enable the dense packaging of the battery cells. The serial stacking configuration is termed a bipolar stack, which has the advantages of reducing overall cell weight, simplifying the interfaced connections for the cell, and minimizing the cooling requirements. Lastly, the optimization of battery components will occur through a robust and rigorous combination of various computational modeling techniques covering multiple length scales. The expected result will be a fully solid-state battery with operational temperatures up to 150°C, providing the required energy density, discharge rates, and inherent safety to meet the strict aerospace mission performance criteria. The SABERS team employed novel materials development, computational modeling, and design-of-experiments (DOE) optimization studies in their research. This presentation will show the results of these studies and demonstrate a feasible path for solid-state cells with a specific energy greater than 400 Wh/kg to enable electric aircraft.

Computational Modeling↗