Engineering topics

Yang, Wanli

Publications and source records attributed to Yang, Wanli.

At least 37 records · Page 2

DOE OSTI2024

Mechanochemically Robust LiCoO 2 with Ultrahigh Capacity and Prolonged Cyclability

Pushing intercalation-type cathode materials to their theoretical capacity often suffers from fragile Li-deficient frameworks and severe lattice strain, leading to mechanical failure issues within the crystal structure and fast capacity fading. This is particularly pronounced in layered oxide cathodes because the intrinsic nature of their structures is susceptible to structural degradation with excessive Li extraction, which remains unsolved yet despite attempts involving elemental doping and surface coating strategies. Herein, a mechanochemical strengthening strategy is developed through a gradient disordering structure to address these challenges and push the LiCoO 2 (LCO) layered cathode approaching the capacity limit (256 mAh g -1 , up to 93% of Li utilization). This innovative approach also demonstrates exceptional cyclability and rate capability, as validated in practical Ah-level pouch full cells, surpassing the current performance benchmarks. Comprehensive characterizations with multiscale X-ray, electron diffraction, and imaging techniques unveil that the gradient disordering structure notably diminishes the anisotropic lattice strain and exhibits high fatigue resistance, even under extreme delithiation states and harsh operating voltages. Consequently, this designed LCO cathode impedes the growth and propagation of particle cracks, and mitigates irreversible phase transitions. In conclusion, this work sheds light on promising directions toward next-generation high-energy-density battery materials through structural chemistry design.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Unlocking iron metal as a cathode for sustainable Li-ion batteries by an anion solid solution

Traditional cathode chemistry of Li-ion batteries relies on the transport of Li-ions within the solid structures, with the transition metal ions and anions acting as the static components. Here, we demonstrate that a solid solution of F – and PO 4 3– facilitates the reversible conversion of a fine mixture of iron powder, LiF, and Li 3 PO 4 into iron salts. Notably, in its fully lithiated state, we use commercial iron metal powder in this cathode, departing from electrodes that begin with iron salts, such as FeF 3 . Our results show that Fe-cations and anions of F – and PO 4 3– act as charge carriers in addition to Li-ions during the conversion from iron metal to a solid solution of iron salts. This composite electrode delivers a reversible capacity of up to 368 mAh/g and a specific energy of 940 Wh/kg. Our study underscores the potential of amorphous composites comprising lithium salts as high-energy battery electrodes.

25 ENERGY STORAGE↗

DOE OSTI2024

Enhanced Electrochemical Performance of Disordered Rocksalt Cathodes in a Localized High‐Concentration Electrolyte

Abstract Lithium (Li)‐rich transition metal oxide cathodes with a cation disordered rock salt structure (DRX) are increasingly gaining popularity for advanced Li batteries as they offer high capacity and cost benefits over the commonly used layered Li transition metal oxide cathodes. However, the performance of DRX cathodes and their applications are limited by severe side reactions between the cathode and the state‐of‐the‐art carbonate‐based electrolytes at high voltage of 4.8 V, transition metal dissolution, and structural instability of the cathode particles. In this work, an advanced localized high‐concentration electrolyte (LHCE) is developed to form a stable cathode‐electrolyte interphase and mitigate structural instability of the Li 1.13 Mn 0.66 Ti 0.21 O 2 (LMTO) DRX during electrochemical cycling. Li||LMTO half cells with the LHCE demonstrate increased capacity, cycling stability, and superior rate capability compared with cells containing a conventional carbonate electrolyte. For instance, the Li||LMTO cells cycled in LHCE show a higher initial capacity of 205.2 mAh g −1 and a better capacity retention of 72.5% after 200 cycles at a current density of 20 mA g −1 than those with the conventional electrolyte (initial capacity of 187.7 mAh g −1 and capacity retention of 19.9%). This work paves the way to the development of practical DRX cathode‐based high‐energy Li batteries.

25 ENERGY STORAGE↗

DOE OSTI2024

Robust Machine Learning Inference from X-ray Absorption Near Edge Spectra through Featurization

X-ray absorption spectroscopy (XAS) is a commonly employed technique for characterizing functional materials. In particular, X-ray absorption near edge spectra (XANES) encode local coordination and electronic information, and machine learning approaches to extract this information are of significant interest. To date, most ML approaches for XANES have primarily focused on using the raw spectral intensities as input, overlooking the potential benefits of incorporating spectral transformations and dimensionality reduction techniques into ML predictions. Here, in this work, we focused on systematically comparing the impact of different featurization methods on the performance of ML models for XAS analysis. We evaluated the classification and regression capabilities of these models on computed data sets and validated their performance on previously unseen experimental data sets. Our analysis revealed an intriguing discovery: the cumulative distribution function feature achieves both high prediction accuracy and exceptional transferability. This remarkably robust performance can be attributed to its tolerance to horizontal shifts in the spectra, which is crucial when validating models using experimental data. While this work exclusively focuses on XANES analysis, we anticipate that the methodology presented here will hold promise as a versatile asset to the broader spectroscopy community.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Protonation Stimulates the Layered to Rock Salt Phase Transition of Ni‐Rich Sodium Cathodes

Abstract Protonation of oxide cathodes triggers surface transition metal dissolution and accelerates the performance degradation of Li‐ion batteries. While strategies are developed to improve cathode material surface stability, little is known about the effects of protonation on bulk phase transitions in these cathode materials or their sodium‐ion battery counterparts. Here, using NaNiO 2 in electrolytes with different proton‐generating levels as model systems, a holistic picture of the effect of incorporated protons is presented. Protonation of lattice oxygens stimulate transition metal migration to the alkaline layer and accelerates layered‐rock‐salt phase transition, which leads to bulk structure disintegration and anisotropic surface reconstruction layers formation. A cathode that undergoes severe protonation reactions attains a porous architecture corresponding to its multifold performance fade. This work reveals that interactions between electrolyte and cathode that result in protonation can dominate the structural reversibility/stability of bulk cathodes, and the insight sheds light for the development of future batteries.

25 ENERGY STORAGE↗

DOE OSTI2023

The Chemical and Electronic Properties of Stability-Enhanced, Mixed Ir-TiO x Oxygen Evolution Reaction Catalysts

Iridium has emerged as the leading catalyst material for the anodic oxygen evolution reaction (OER) in acidic media. Often, iridium is mixed with more stable materials such as titanium. For these materials, the electronic structure of titanium plays a crucial role since with varying degrees of oxidation titanium transforms to semiconducting or even insulating phases. Yet, the electronic properties of mixed Ir-TiO x catalysts have never been systematically studied. In this study, we correlate the catalytic performance of mixed Ir-TiO x -based OER catalysts with the electronic structure of the surface layers. For this, a thin film material library with a 20-70 at. % Ir (Ir/[Ir + Ti]) compositional gradient was prepared. We used inductively coupled plasma mass spectrometry to test the OER activity and stability of the set of mixed Ir-TiO x catalyst candidate materials. Complementary, Ti L 2,3 - and O K-edge X-ray absorption spectroscopy and depth-dependent X-ray photoelectron spectroscopy measurements were performed to correlate the catalytic performance with the composition and electronic property profiles of these mixed Ir-TiO x OER anode catalysts. The spectroscopic analysis reveals that titanium is present as an intermixed matrix of semiconductive but stable TiO 2 , conductive but less stable titanium-suboxides (TiO x ), and highly conductive but highly unstable metallic Ti(0). The extent of the titanium oxidation strongly depends on the titanium content, with a lower degree of oxidation observed for lower titanium (and thus higher iridium) contents. For an iridium loading of 70 at. %, the respective mixed Ir-TiO x catalyst showed a similar OER activity to that of the pure metallic iridium (1.74 vs 1.59 VRHE, respectively) but with a 71% lower iridium dissolution rate relative to the pure metallic iridium. This demonstrates the stabilization effect of titanium addition while maintaining high OER activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Li 2 MnO 3 : A Catalyst for a Liquid Cl 2 Electrode in Low‐Temperature Aqueous Batteries

Abstract Li 2 MnO 3 has been contemplated as a high‐capacity cathode candidate for Li‐ion batteries; however, it evolves oxygen during battery charging under ambient conditions, which hinders a reversible reaction. However, it is unclear if this irreversible process still holds under subambient conditions. Here, the low‐temperature electrochemical properties of Li 2 MnO 3 in an aqueous LiCl electrolyte are evaluated and a reversible discharge capacity of 302 mAh g −1 at a potential of 1.0 V versus Ag/AgCl at −78 °C with good rate capability and stable cycling performance, in sharp contrast to the findings in a typical Li 2 MnO 3 cell cycled at room temperature, is observed. However, the results reveal that the capacity does not originate from the reversible oxygen oxidation in Li 2 MnO 3 but the reversible Cl 2 (l)/Cl − (aq.) redox from the electrolyte. The results demonstrate the good catalytic properties of Li 2 MnO 3 to promote the Cl 2 /Cl − redox at low temperatures.

Sui, Yiming↗

DOE OSTI2023

Core-Level Spectroscopy with Hard and Soft X-rays on Phosphorus-Containing Compounds for Energy Conversion and Storage

The electronic properties of nine solid phosphorus (P)-containing compounds with varying oxidation states and chemical environments, including GaP (–III) , InP (–III) , red-P (0) , H 3 P (III) O 3 , Na 2 H 2 P 2 (IV) O 6 , H 3 P (V) O 4 , KH 2 P (V) O 4 , Na 2 HP (V) O 4 , and InP (V) O 4 , are investigated using X-ray absorption near-edge structure (XANES) spectroscopy in the hard (P K-edge) and soft X-ray regime (P L 2,3 - edge). We find shifts in the absorption-edge positions and correlate them with the ligands surrounding the P atom, likely causing a different core–hole interaction screening for different compounds. Complementing the experimental analysis, ab initio many-body calculations of XANES spectra provide insights into the excitonic nature of the observed spectral features and their impact on the electronic structure of the materials. Furthermore, we report on P K-edge XANES measurements on aqueous phosphorus-containing acids, including H 3 PO 3 , H 3 PO 4 , and their mixtures. At first sight, the spectra of the aqueous acids are similar to those of their solid counterparts. However, close inspection reveals a slight red shift of the absorption edge and the presence of fewer spectral features compared with spectra of the respective solids. Mixtures of aqueous acids display spectral features corresponding to the individual components, indicating the potential for speciation and quantification through fingerprinting.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Revealing the effect of LiOH on forming a SEI using a Co magnetic “probe”

The solid-electrolyte-interphase (SEI) plays a critical role in lithium-ion batteries (LIBs) because of its important influence on electrochemical performance, such as cycle stability, coulombic efficiency, etc. Although LiOH has been recognized as a key component of the SEI, its influence on the SEI and electrochemical performance has not been well clarified due to the difficulty in precisely controlling the LiOH content and characterize the detailed interface reactions. Here, a gradual change of LiOH content is realized by different reduction schemes among Co(OH) 2 , CoOOH and CoO. With reduced Co nanoparticles as magnetic “probes”, SEI characterization is achieved by operando magnetometry. By combining comprehensive characterization and theoretical calculations, it is verified that LiOH leads to a composition transformation from lithium ethylene di-carbonate (LEDC) to lithium ethylene mono-carbonate (LEMC) in the SEI and ultimately results in capacity decay. This work unfolds the detailed SEI reaction scenario involving LiOH, provides new insights into the influence of SEI composition, and has value for the co-development between the electrode materials and electrolyte.

25 ENERGY STORAGE↗

DOE OSTI2023

Li–Mn–O Li-rich cation disordered rock-salt cathode materials do not undergo reversible oxygen redox during cycling

An in-depth study of “Li 4 Mn 2 O 5 ”, a nanocomposite of Li 2 O and Li 4-x Mn 2 O 5 with a disordered rock salt structure (LMO), was conducted to determine the origins of the observed anomalously high charge and discharge capacity in lithium cells, which can exceed 350 mA h g -1 . Using soft and hard X-ray absorption spectroscopy (XAS), mapping of resonant inelastic X-ray scattering (mRIXS), and X-ray Raman spectroscopy (XRS), it was determined that electrochemical decomposition of Li 2 O upon charge and reduction of Mn to below 3+ during discharge is responsible for the capacities that are observed, with no evidence of contributions from reversible oxygen redox. Here, the over-reduction is exacerbated when charging limits of 4.5–4.8 V are used due to side reactions between electrolytic solution and the highly oxidized active material. These side reactions result in dissolution of Mn at room temperature and release of oxygen and other gases during initial cycles, which, in turn, cause rapid capacity fading. This is accompanied by evolution of the voltage profile upon cycling towards one that resembles that of manganese oxide spinels. The cycling behavior can be improved somewhat by reducing the upper voltage limit, although this results in a diminishment of the discharge capacities below 200 mA h g -1 . By adding various amounts of spinel LiMn 2 O 4 during synthesis, it was possible to produce LMOs with rock salt structures having significantly improved cycling behavior but still having capacities in excess of 250 mA h g -1 . An optimized modified material also exhibits better rate capability and much less gas evolution during initial cycles than the unmodified LMO. Interestingly, as-made modified materials generally exhibited lower than expected average Mn oxidation states attributable to oxygen loss during the synthesis process, as well as higher capacities than expected based on their manganese contents. The oxygen loss during processing may reduce the activity of the remaining oxygen and account for the lower reactivity of the spinel-modified material.

25 ENERGY STORAGE↗

DOE OSTI2023

Epitaxial growth of hexagonal BaNi O 3–δ thin films on SrTi O 3 (111) substrates

Transition metal oxides containing nickel species in oxidation states higher than 3+ often exhibit high catalytic activity, which makes them promising for applications as advanced electrocatalysts for water splitting and fuel cells. Here, we examine the structure and properties of BaNiO 3 (BNO) thin films, containing formally Ni 4+ , grown on SrTiO 3 (111) substrates using oxygen-plasma–assisted molecular beam epitaxy. X-ray diffraction and scanning transmission electron microscopy measurements reveal that BNO films have a hexagonal structure with $c$- and $a$-axes of mixed textures showing epitaxial relationships BNO (0001) ∥ SrTiO 3 (111) and BNO (10$\overline{1}$0) ∥ SrTi O 3 (111), respectively. The formation of the $a$-axis texture is dominant due to the smaller lattice mismatch with the substrate. Here, density functional theory calculations confirm that the hexagonal BNO film with the $a$-axis texture is energetically more favorable than the competing $c$-axis texture. Detailed spectroscopy data analysis indicates that hexagonal BNO films contain mixtures of Ni 2+ , Ni 3+ , and Ni 4+ species, with Ni 4+ being dominant. Our study provides insights into stabilizing Ni 4+ in complex oxides, which is important for further exploration of the potential of materials containing Ni 4+ .

36 MATERIALS SCIENCE↗

DOE OSTI2023

Chemical and Electronic Structure at the Interface between a Sputter-Deposited Zn(O,S) Buffer and a Cu(In,Ga)(S,Se) 2 Solar Cell Absorber

The chemical and electronic structure of the interface between a sputter-deposited Zn(O,S) buffer layer and an industrial Cu(In,Ga)(S,Se) 2 (CIGSSe) absorber for thin-film solar cells is investigated with X-ray and UV photoelectron spectroscopy, inverse photoemission spectroscopy, and X-ray emission spectroscopy. We find a CIGSSe absorber surface band gap of 1.61 (±0.14) eV, which is significantly increased as compared to the minimal value derived with bulk-sensitive methods (≈1.1 eV). We find no indication for diffusion of absorber elements into the buffer layer. Surface- and bulk-sensitive measurements of the buffer layer suggest the presence of S-Zn and S-O bonds in the Zn(O,S) layer. We find that the naturally existing downward band bending toward the CIGSSe absorber surface is increased by the formation of the interface, likely enhancing carrier separation under illumination. We also derive a flat conduction band alignment, in line with the reported high conversion efficiencies of corresponding large-area solar cells.

14 SOLAR ENERGY↗

DOE OSTI2023

Highly Oxidized Oxide Surface toward Optimum Oxygen Evolution Reaction by Termination Engineering

The oxygen evolution reaction (OER) is a critical step for sustainable fuel production through electrochemistry process. Maximizing active sites of nanocatalyst with enhanced intrinsic activity, especially the activation of lattice oxygen, is gradually recognized as the primary incentive. Since the surface reconfiguration to oxyhydroxide is unavoidable for oxygen-activated transition metal oxides, developing a surface termination like oxyhydroxide in oxides is highly desirable. In this work, we demonstrate an unusual surface termination of (111)-facet Co 3 O 4 nanosheet that is exclusively containing edge-sharing octahedral Co 3+ similar to CoOOH that can perform at approximately 40 times higher current density at 1.63 V (vs RHE) than commercial RuO 2 . It is found that this surface termination has an oxidized oxygen state in contrast to standard Co-O systems, which can serve as active site independently, breaking the scaling relationship limit. Finally, this work forwards the applications of oxide electrocatalysts in the energy conversion field by surface termination engineering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Toward Stable Cycling of a Cost-Effective Cation-Disordered Rocksalt Cathode via Fluorination

The recently developed Li-excess cation-disordered rock salts (DRXs) exhibit an excellent chemical diversity for the development of alternative Co/Ni-free high-energy cathodes. Herein, the synthesis of a highly fluorinated DRX cathode, Li 1.2 Mn 0.6 Ti 0.2 O 1.8 F 0.2 , based on cost-effective and earth-abundant transition metals, via a solid-state reaction, is reported. The fluorinated DRX cathode using ammonium fluoride precursor exhibits more uniform particle size and delivers a specific discharge capacity of 233 mAh g -1 and specific energy of 754 Wh kg -1 , with 206 mAh g -1 retained after 200 cycles. Further, the combined synchrotron X-ray absorption spectroscopy and resonant inelastic X-ray scattering spectroscopy analysis reveals that the remarkable cycling performance is attributed to the high fluorination and thus enhanced Mn content, enabling the utilization of more Mn redox than the oxide analog. This study demonstrates a great promise to develop next-generation cost-effective DRX cathodes with enhanced capacity retention for high-energy Li-ion batteries.

25 ENERGY STORAGE↗

DOE OSTI2023

Satellite-Dominated Sulfur L 2,3 X-ray Emission of Alkaline Earth Metal Sulfides

The sulfur L 2,3 X-ray emission spectra of the alkaline earth metal sulfides BeS, MgS, CaS, SrS, and BaS are investigated and compared with spectra calculations based on density functional theory. Very distinct spectral shapes are found for the different compounds. With decreasing electronegativity of the cation, that is, increasing ionic bonding character, the upper valence band width and its relative spectral intensity decrease. These general trends are qualitatively reproduced by the spectra calculations, which give quite an accurate description of the spectral shapes in the upper valence band region. On the low energy side of the sulfur 3s → 2p transition dominating the spectra, we find strong satellites caused by "semi-Auger" decays involving configuration interaction. These satellites, previously believed to be energetically forbidden for sulfur L 2,3 emission and only observed for the L 2,3 emission of Cl to Cr, increase in intensity as the bonding character becomes more ionic and dominate the spectra for SrS and BaS. The intensities, energies, and widths of the satellites vary strongly between the investigated compounds, giving a very specific spectral fingerprint that can be used for speciation analysis.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Towards commercialization of fluorinated cation-disordered rock-salt Li-ion cathodes

Cation-disordered rock-salt cathodes (DRX) are promising materials that could deliver high capacities (>250 mAh g −1 ) with Earth abundant elements and materials. However, their electrochemical performances, other than the capacity, should be improved to be competitive cathodes, and many strategies have been introduced to enhance DRXs. Fluorination has been shown to inhibit oxygen loss and increase power density. Nevertheless, fluorinated cation-disordered rock-salts still suffer from rapid material deterioration and low scalability which limit their practical applications. This mini-review highlights the key challenges for the commercialization of fluorinated cation-disordered rock-salts, discusses the underlying reasons behind material failure and proposes future development directions.

25 ENERGY STORAGE↗

DOE OSTI2022

Optimizing Li‐Excess Cation‐Disordered Rocksalt Cathode Design Through Partial Li Deficiency

Li-excess disordered rocksalts (DRXs) are emerging as promising cathode materials for Li-ion batteries due to their ability to use earth-abundant transition metals. In this work, a new strategy based on partial Li deficiency engineering is introduced to optimize the overall electrochemical performance of DRX cathodes. Specifically, by using Mn-based DRX as a proof-of-concept, it is demonstrated that the introduction of cation vacancies during synthesis (e.g., Li 1.3-x Mn 2+ 0.4-x Mn 3+ x Nb 0.3 O 1.6 F 0.4 , x = 0, 0.2, and 0.4) improves both the discharge capacity and rate performance due to the more favored short-range order in the presence of Mn3+. Density functional theory calculations and Monte Carlo simulations, in combination with spectroscopic tools, reveal that introducing 10% vacancies (Li 1.1 Mn 2+ 0.2 Mn 3+ 0.2 Nb 0.3 O 1.6 F 0.4 ) enables both Mn 2+ /Mn 3+ redox and excellent Li percolation. However, a more aggressive vacancy doping (e.g., 20% vacancies in Li 0.9 Mn 3+ 0.4 Nb 0.3 O 1.6 F 0.4 ) impairs performance because it induces phase separation between an Mn-rich and a Li-rich phase.

25 ENERGY STORAGE↗

DOE OSTI2022

Robust Fe divalent state in one-unit-cell $\mathrm{FeSe/SrTiO_3}$ thin films

The orbital occupancy, as the origin of Hund's rule coupling, provides critical information in understanding the multiorbital iron-based superconductors. The one-unit-cell (1UC) FeSe thin film on a SrTiO 3 substrate with superconductive T c above 60 K has been reported with unique electronic structures as well as orbital occupancy. In this paper, we present the x-ray absorption spectroscopy and resonant inelastic x-ray scattering (RIXS) study of the FeSe/STO thin films of different thicknesses. Together with the atomic multiplet simulation analysis, the FeSe/STO thin films (from 1UC to 10UC) are shown with the pure 3d6 electronic configuration which is identical to the bulk FeSe. Moreover, 1UC FeSe/STO is found to be distinctively more persistent in hosting the 3d6 configuration other than the thicker films under the oxidization process. The robustness of the 3d6 in 1UC FeSe/STO is discussed as a result of charge transfer from the substrate, as well as a mechanism to maintain the high-T c superconductivity. Additionally our research calls for a further high-resolution RIXS study of the pristine superconductive 1UC FeSe/STO thin film.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗