Engineering Papers⌕ Search

Engineering topics

Yang, Dali

Publications and source records attributed to Yang, Dali.

At least 37 records · Page 2

Deoxydehydration of Biomass-Derived Polyols with a Reusable Unsupported Rhenium Nanoparticles Catalyst

Oxorhenium catalysts effectively transform biomass derived polyols into corresponding alkenes, via deoxydehydration (DODH) with a secondary alcohol as a hydrogen donor. This report describes the preparation of unsupported rhenium oxide nanoparticles (ReO x NPs), their use as DODH heterogeneous catalyst, and changes in the speciation and structure of Re during catalysis leading to a mechanism for DODH by a heterogeneous catalyst. The unsupported nanoparticles catalyze various polyols transformation to produce alkenes with high efficiency and recyclability. X-ray spectroscopy analysis shows the structure of as-prepared ReO x NPs is similar to perrhenate with oxidation state between Re(VI) and Re(VII). Under reaction conditions and post catalysis, the ReOx NPs are reduced by approximately two oxidation units. Kinetic isotope effect demonstrates that dissociation of a C-H bond during reduction of ReO x NPs by 3-octanol is part of the rate-determining step. Based on all experimental observations, the mechanism of DODH catalysis with unsupported ReO x NPs involving a Re(VII)/Re(V) redox-pair is introduced.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of non-solvent chemistry on polybenzimidazole hollow fiber membrane preparation

Polybenzimidazole membrane materials have attractive H 2 /CO 2 separation characteristics and high thermo-chemical stability for elevated temperature synthesis (syn) gas separations. The development of PBI membranes with a thin defect-free selective layer and porous support morphology is vital to achieving industrially attractive separation performance. This work is focused on developing a fundamental understanding of the liquid-liquid demixing-based phase inversion process for asymmetric PBI hollow fiber membrane (HFM) formation. The development of industrially attractive HFMs is a challenging process due to the complex interplay between phase equilibria, phase inversion kinetics, and interfacial mass transfer that exist during the liquid-liquid demixing process. Numerous parameters including the dope, bore, and outer coagulant chemistries and compositions significantly influence the HFM morphologies produced. Here, a systematic study is conducted to investigate the phase inversion process parameters including the roles of the non-solvent solubility and diffusivity parameters with respect to the solvent and PBI on the phase inversion process. Furthermore, the influence of dope, bore and coagulant chemistries and compositions on PBI HFM morphology are investigated. As a result, the fabricated PBI HFMs are evaluated for their ideal H 2 and CO 2 permeance and H 2 /CO 2 selectivity at 250 °C to benchmark their separation performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nitroplasticizer-water phase diagram

Nitroplasticizer (NP) is used in conjunction with poly(ester urethane) block co-polymer as binder material for polymer bonded explosives (PBX). Water content contributes directly to the stability of NP, poly(ester urethane), and ultimately the PBX. Therefore a n NP-water miscibility phase diagram can be an important tool in understanding potential water content in NP and further PBX processes. To determine the NP-water miscibility phase diagram, a systematic series of experiments was conducted. NP samples were saturated with water and ramped through incremental temperature steps. Aliquots were taken at each step after equilibration. Water content in NP was determined by Coulmetric Karl Fischer (KF) titration at each incremental temperature step. The sample aliquots were then analyzed by Thermogravimetric analysis (TGA), Differential Scanning Calorimetry (DSC), and Transmission Fourier Transform Infrared Spectroscopy (Near-IR). The resultant data were analyzed and combined to construct a n NP-water phase diagram. The phase diagram, ranging from 500 ppm to 5800 ppm water concentration and –90°C to 130°C, contains six distinct phases separated by five distinct phase separations.

36 MATERIALS SCIENCE↗

Characterization of Various Materials Using Refractometry

Refractive index (RI) is a fundamental physical property of a material. However, the RI values of several binders, including nitroplasticizer (NP), Estanes, and KelF/FK 800, are not available in literature. Further, their temperature dependencies are undocumented either. In this study, we have developed a set of methodologies to accurately and effectively determine the RIs of these binder materials between 20 and 70°C. The RIs of these binders without aging show linear correlations with temperature, as shown in the figure below. Among these materials, Estane 5714 has the highest RI whereas FK800 has the lowest RI. As materials age, the changes in their RIs are different, suggesting different aging behavior of these binders upon heating. Typically, NP and Estane degraded through hydrolysis give lower RIs than the baseline materials. However, when KelF/FK800 materials thermally age, their RIs increase. Overall, this study demonstrates refractometry is a sensitive technique to detect aging signs in various materials of interest.

36 MATERIALS SCIENCE↗

Development of activity–descriptor relationships for supported metal ion hydrogenation catalysts on silica

With the increasing attention on single-site heterogeneous catalysts on account of their high specific activity, more effective catalyst design strategies are necessary. We demonstrate a first-principles-calculation-guided active-site design strategy for alkene hydrogenation using silica-supported single-atom single-site heterogeneous catalysts (SSHCs, i.e., M/SiO2). An activity-descriptor relationship for propylene hydrogenation was established using representative catalysts (i.e., Ga3+, Zn2+, Mn2+ and Ti4+/SiO2), correlating the computational activity descriptor (i.e., the reaction free energy of the metal hydride formation) with the experimental reaction rates. Microkinetic modeling confirmed the predicted reaction mechanisms and further explained the rationale of the activity-descriptor relationship. This relationship was then used to predict the trend of activities of a variety of isolated ions on silica, and an In3+/SiO2 catalyst was identified as the most promising candidate based on its predicted activity and synthetic feasibility. The monodispersed In3+/SiO2 catalyst was then synthesized, for the first time, and showed higher propylene hydrogenation activity than the other four single-atom SSHCs, as predicted. Detailed spectroscopic characterization (XAS, XPS, DRIFTS and DRUV-Vis) provided insights into coordination environments and oxidation states of the catalysts, as well as evidence for the hydride intermediate. The successful discovery of the In3+/SiO2 catalyst for propylene hydrogenation using the first-principles-calculations-guided design strategy opens up new opportunities for efficient development of single-atom SSHCs.

DFT↗

Low-Pressure Flow Chemistry of CuAAC Click Reaction Catalyzed by Nanoporous AuCu Membrane

Click chemistry has been widely used in bioconjugation, polymer synthesis, and the development of new anticancer drugs. Here, we report a nanoporous membrane made of AuCu alloy nanowires, which can effectively catalyze copper(I)-catalyzed 1,3-dipolar cycloaddition between azide and terminal alkyne (CuAAC) in flow condition with pressure less than one bar. Comparison studies of the nanowires before and after the reaction using X-ray photoelectron spectroscopy reveal Cu(0) and Cu(I) are main species that promote the reaction. This simple strategy can be used to synthesize a variety of compounds with triazole linkage and extended to gram level chemical production.

catalyst↗

Binary Transition-Metal Oxide Hollow Nanoparticles for Oxygen Evolution Reaction

Low-cost transition metal oxides are actively explored as alternative materials to precious metal-based electrocatalysts for the challenging multistep oxygen evolution reaction (OER). We utilized the Kirkendall effect allowing the formation of hollow polycrystalline, highly disordered nanoparticles (NPs) to synthesize highly active binary metal oxide OER electrocatalysts in alkali media. Two synthetic strategies were applied to achieve compositional control in binary transition metal oxide hollow NPs. The first strategy is capitalized on the oxidation of transition-metal NP seeds in the presence of other transition-metal cations. Oxidation of Fe NPs treated with Ni (+2) cations allowed the synthesis of hollow oxide NPs with a 1-4.7 Ni-to-Fe ratio via an oxidation-induced doping mechanism. Hollow Fe-Ni oxide NPs also reached a current density of 10 mA/cm(2) at 0.30 V overpotential. The second strategy is based on the direct oxidation of iron-cobalt alloy NPs which allows the synthesis of hollow FexCo100-x-oxide NPs where x can be tuned in the range between 36 and 100. Hollow Fe36Co64 -oxide NPs also revealed the current density of 10 mA/cm(2) at 0.30 V overpotential in 0.1 M KOH.

hollow nanoparticles↗

Catalytic chemoselective functionalization of methane in a metal-organic framework

Methane constitutes the largest fraction of natural gas reserves and is a low-cost abundant starting material for the synthesis of value-added chemicals and fuel. Selective catalytic functionalization of methane remains a vital goal in the chemical sciences due to its low intrinsic reactivity. Borylation has recently emerged as a promising route for the catalytic functionalization of methane. A major challenge in this regard is selective borylation towards the monoborylated product that is more active than methane and can easily lead to over-functionalization. Herein, we report a highly selective microporous metal-organic framework- supported iridium(III) catalyst for methane borylation that exhibits a chemoselectivity of > 99% (mono versus bis at 19.5% yield; turnover number = 67) for monoborylated methane, with bis(pinacolborane) as the borylation reagent in dodecane, at 150 °C and 34 atm of methane, employing as little as 1.8 wt% of iridium. The preference for the monoborylated product is ascribed to the shape-selective effect of the metal-organic framework pore structures.

Zhang, Xuan (ORCID:0000000182147265)↗

Nonresonant valence-to-core x-ray emission spectroscopy of niobium

The valence-to-core (V2C) portion of x-ray emission spectroscopy (XES) measures the electron states close to the Fermi level. These states are involved in bonding, thus providing a measure of the chemistry of the material. For this paper, we show the V2C XES spectra for several niobium compounds. The Kβ" peak in the V2C XES results from the transition of a ligand 2s electron into the 1s core-hole of the niobium, a transition allowed by hybridization with the niobium 4p . This location in energy of this weak peak shows a strong ligand dependence, thus providing a sensitive probe of the ligand environment about the niobium.

36 MATERIALS SCIENCE↗

Chemoselective Hydrogenation with Supported Organoplatinum(IV) Catalyst on Zn(II)-Modified Silica

For this research, well-defined organoplatinum(IV) sites were grafted on a Zn(II)-modified SiO 2 support via surface organometallic chemistry in toluene at room temperature. Solid-state spectroscopies including XAS, DRIFTS, DRUV–vis, and solid-state (SS) NMR enhanced by dynamic nuclear polarization (DNP), as well as TPR-H 2 and TEM techniques revealed highly dispersed (methylcyclopentadienyl)methylplatinum(IV) sites on the surface ((MeCp)PtMe/Zn/SiO 2 , 1). In addition, computational modeling suggests that the surface reaction of (MeCp)PtMe 3 with Zn(II)-modified SiO 2 support is thermodynamically favorable (ΔG = -12.4 kcal/mol), likely due to the increased acidity of the hydroxyl group, as indicated by NH 3 -TPD and DNP-enhanced 17 O{ 1 H} SSNMR. In situ DRIFTS and XAS hydrogenation experiments reveal the probable formation of a surface Pt(IV)-H upon hydrogenolysis of Pt-Me groups. The heterogenized organoplatinum(IV)-hydride sites catalyze the selective partial hydrogenation of 1,3-butadiene to butenes (up to 95%) and the reduction of nitrobenzene derivatives to anilines (up to 99%) with excellent tolerance of reduction-sensitive functional groups (olefin, carbonyl, nitrile, halogens) under mild reaction conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Supported Single-Site Ti(IV) on a Metal–Organic Framework for the Hydroboration of Carbonyl Compounds

Here, a stable and structurally well-defined titanium alkoxide catalyst supported on a metal-organic-framework (MOF) of UiO-67 topology (ANL1-Ti(O i Pr) 2 ) was synthesized and fully characterized by a variety of analytical and spectroscopic techniques, including BET, TGA, PXRD, XAS, DRIFT, SEM, and DFT computations. The Ti-functionalized MOF was demonstrated active for the catalytic hydroboration of a wide range of aldehydes and ketones with HBpin as the boron source. Compared to traditional homogeneous and supported hydroboration catalysts, ANL1-Ti(O i Pr) 2 is completely recyclable and reusable, making it a promising hydroboration catalyst alternative for green and sustainable chemical synthesis. DFT calculations suggest that the catalytic hydroboration proceeds via a (1) hydride transfer between the active Ti-hydride species and a carbonyl moiety (rate determining step), and (2) alkoxide transfer (intramolecular σ-bond metathesis) to generate the boronate ester product.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Anisotropic Thermal Behavior of Silicone Polymer, DC 745

In material applications, it is important to understand how polymeric materials behave in the various environments they may encounter. One factor governing polymer behavior is processing history. Differences in fabrication will result in parts with varied or even unintended properties. In this work, the thermal expansion behavior of silicone DC 745 is studied. Thermomechanical analysis (TMA) is used to determine changes in sample dimension resulting from changes in temperature. This technique can measure thermal events such as the linear coefficient of thermal expansion (CTE), melting, glass transitions, cure shrinkage, and internal relaxations. Using a thermomechanical analyzer (Q400 TMA), it is determined that DC 745 expands anisotropically when heated. This means that the material has a different CTE depending upon which direction is being measured. In this study, TMA experiments were designed in order to confirm anisotropic thermal behavior in multiple DC 745 samples of various ages and lots. TMA parameters such as temperature ramp rate, preload force, and temperature range were optimized in order to ensure the most accurate and useful data. A better understanding of the thermal expansion of DC 745 will allow for more accurate modeling of systems using this material.

36 MATERIALS SCIENCE↗

Effect of Filler Concentration on Thermal Stability of Vinyl Copolymer Elastomer (VCE) Composites

To study the thermal stability of vinyl copolymer elastomer (VCE) in its composite form, systematic TGA characterizations were conducted in both nonisothermal and isothermal modes. The effects of filler concentration on the aging behaviors of the VCE/filler composites were investigated under nitroplasticizer (NP) environment. FTIR characterization was used to probe the structural changes in the VCE polymer before and after the thermal treatments. This study suggests that the filler concentration significantly deteriorates the thermal stability of NP at a moderate temperature (< 70 °C). The degradation of NP, in turn, accelerates the aging process of the VCE polymer in its composite form.

36 MATERIALS SCIENCE↗

Thermal and chemical stabilization of ethylene/vinyl acetate/vinyl alcohol (EVA-OH) terpolymers under nitroplasticizer environments

Here, we compare the aging behaviors of cross-linked ethylene/vinyl acetate/vinyl alcohol terpolymers, also referred to as EVA-OH, when they are either immersed in nitroplasticizer (NP) liquid or exposed to NP vapor at different temperatures. And while thermogravimetric analysis and differential scanning calorimetry are used to probe the thermal stability of aged NP and polymers, Fourier transform infrared, gel permeation chromatography, ultra-violet/vis, and nuclear magnetic resonance are used to probe their structural changes over the aging process. Our study confirms that NP degrades through C[BOND]N cleavage, and releases HONO molecules at a slightly elevated temperature (<75°C). As these molecules accumulate in the vapor phase, they react among themselves to create an acidic environment. Therefore, these chemical constituents in the NP vapor significantly accelerate the hydrolysis of EVA-OH polymer. When the hydrolysis occurs in both vinyl acetate and urethane groups and the scission at the cross-linker progresses, EVA-OH becomes vulnerable to further degradation in the NP vapor environment. Finally, through the comprehensive characterization, the possible degradation mechanisms of the terpolymers are proposed.

36 MATERIALS SCIENCE↗

High Temperature Polymer-Based Membrane Systems for Pre-Combustion Carbon Dioxide Capture

This report describes the activities conducted by Los Alamos National Laboratory and our project partners in support of DOE’s program to develop carbon capture technologies for power systems. This work was aimed at continued development and demonstration of a membrane based pre-combustion hydrogen purification/carbon capture technology and separation schemes developed by LANL.

Carbon Capture↗