Engineering Papers⌕ Search

Engineering topics

Xue, Lincoln

Publications and source records attributed to Xue, Lincoln.

At least 19 records

Stacked-Die SiC Half-Bridge Module with Minimum Loop Inductance

Minimizing parasitic inductance of power modules is needed to advance their electrical performance. Innovation in the past decade has driven down the inductance of SiC half-bridge power modules to around 1–2 nH by using multilayer, embedded, and hybrid structures. Further reduction becomes difficult, mainly limited by the excessive interconnects required for the planar placement of vertical conducting chips. To address this, a vertically stacked-die approach is proposed in this paper, taking advantage of the vertical conducting nature of the SiC chips. With ceramic decoupling capacitors integrated, 0.48 nH overall loop inductance is achieved and validated by experimental measurement. This paper also discusses potential approaches to further reduce the inductance.

Ribeiro, Pedro↗

Advanced Packaging Designs

The primary deliverable for this project will be to construct a power electronics package utilizing an organic, electrically insulating substrate material and demonstrate superior thermal performance and greater reliability under thermal cycling, thermal aging, vibration, power cycling, and electrical high-potential evaluation over traditional packages.

ENGINEERING↗

A High-Power Density Segmented Traction Drive Inverter

High power density is one of the requirements for traction drive inverters for meeting increasing demand for higher power and performance electrical vehicles (EV). This paper presents design and preliminary experimental results for a 100 kW high-power density inverter for EV traction drive applications. The inverter design was based on the segmented inverter topology that can significantly reduce the inverter DC filter capacitor and employs low-profile planar double-sided cooled SiC MOSFET-based power modules, compact mini-channel heat sinks with fin-profile optimized using genetic-algorithms, and high-ripple current capacitors. The design produced a compact inverter package with a total volume less than 1 litter, exceeding the power density goal of 100 kW/L. Experimental results are included to demonstrate the cooling and electrical performance.

Su, Gui-Jia↗

Surface Merging Technique to Design GA-Optimized Heat Sinks

High-power density inverters require efficient and small heat dissipation systems. For liquid cooling systems, an effective heat sink design is important to enable higher heat transfer and keep the pressure drop within reasonable limits. A heat sink geometry generated from an extruded, 1D fast Fourier transform can achieve more even temperature distribution and improved heat transfer than a conventional heat sink. Building on this concept, this paper proposes a new heat sink geometry creation algorithm. Instead of one plane profile being extruded, multiple plane profiles, each created from the fast Fourier transform method, are subsequently merged by smooth surfaces along the flow direction of the heat sink. Thus, a 3D heat sink geometry is created that enables 3D coolant flow and efficient heat transfer. The volume of this design was reduced by 50% compared with pin fin heat sinks. Compared with extruded 1D fast Fourier transform heat sinks, the proposed design showed an approximately 5% device temperature reduction and a 20% pressure drop reduction.

Barua, Himel↗

Design Considerations of DC/DC Regulator for High-Power Dynamic Wireless Charging Systems

Due to fast fluctuating input voltage, dynamic wireless charging requires a post-regulator stage for battery charging control and management. This regulator stage has a high requirement on efficiency, size as well as control performance to ensure tight regulation and fast trainset. This paper addresses the control challenges by modeling the system and designing the compensator with input voltage feedforward control. In addition, high resolution PWM is implemented to improve transient performance and current balancing among the phases. Experimental results prove the effectiveness of the proposed schemes and validates 180 kW closed-loop 4-phase operation at 99% efficiency.

Xue, Lincoln↗

Self-Resonant Coil Design for High-frequency High-Power Inductive Wireless Power Transfer

In this paper, the design methodology of a high-frequency, high-power, long-distance inductive wireless power transfer (WPT) is presented. The airgap (d) of a traditional high-power (>1 kW) WPT is limited to a few hundred millimeters, which is almost 1/4th of the coil diameter, D; d ≤ D/4. In this paper, the power transfer distance is significantly increased (d ≥ 1.5D) by adopting a high-frequency magnetic design and GaN-based power electronics. The material and design of the coil and shield are investigated using FEA and tested experimentally. A high frequency 6.78 MHz wireless charging system was built to transfer 1 kW power over 3 m airgap.

Mohammad, Mostak↗

ML-ACCEPT: Machine-Learning-enhanced Automated Circuit Configuration and Evaluation of Power Converters

This project, ML-ACCEPT, took a significant step toward achieving the first objective of the DIFFERENTIATE program: to help engineers to more rapidly and cost-effectively consider a wider range of more novel concepts before selecting an engineering-optimal architecture for high-fidelity detailed design and evaluation. Compared to existing methods, the ML-ACCEPT project investigated innovative technologies to make the design of power converters more cost-effective and time-efficient by i) integrating recent breakthroughs in ML, power electronics, simulation software, and optimization to research, develop, and developed a suite of ML-enhanced hypothesis generation tools for power converter design; and ii) facilitating the integration of the proposed software tools into existing power-converter design work-flows. Some existing tools for power-converter design have a certain level of intelligence to aid the design process, but to our knowledge none of them has ML-enhanced capability of automating the electrical circuit design process by selecting, configuring, and tailoring the individual components that enable available resources (e.g., high-voltage DC power) to be converted to the desired output (e.g., lower-voltage DC power with a desired voltage ripple), subject to application-specific (e.g., plasma generation and automotive applications) thermal and packaging considerations. The state-of-the-art circuit design of power converters is still heavily reliant on human experts to select the optimal topology and search for design parameters with human’s experience and intuitions, which can be very time-consuming, inefficient, and labor intensive. The team is composed of University of Michigan-Dearborn (UM-Dearborn), Lawrence Livermore National Laboratory (LLNL), Oak Ridge National Laboratory (ORNL), Modelon Inc., and lighthouse customers.

42 ENGINEERING↗

Comparative Analysis of Direct and Indirect Cooling of Wide-Bandgap Power Modules and Performance Enhancement of Jet Impingement-Based Direct Substrate Cooling

With the development of high-power and high-torque machines, requirements for high-power density electronics are increasing. Thermal management of such systems requires high heat extraction. Conventional air cooling based heat sinks and cold plate based liquid cooling have their own benefits for various applications but has limitations for high power density applications. The current study explores a jet impingement based direct substrate cooling system that was implemented for a SiC based direct bonded Cu substrate for various power losses. Numerical comparison between jet impingement cooling and conventional horizontal/indirect cooling (pin fin heat sink and genetic algorithm-optimized heat sink) showed that the area weighted average of the heat transfer coefficient (HTC) is high for both horizontal cooling designs, and the local HTC is higher for jet impingement. Design iterations were undertaken to resolve the bottleneck of this cooling system. Increasing the number of nozzles helped to cover more area at the direct bonded Cu bottom plate, which drops the chip temperature considerably. With a constant flow rate, increasing the number of nozzles would decrease local jet velocity, which reduces the heat extraction by jet impingement. This issue can be addressed by reducing the diameter of nozzle but doing so results in a high pressure drop where the design constraint is 2 psi. A flared nozzle design is proposed, which has a higher spreading angle of the jet that increases the flow coverage and reduces the pressure drop of the coolant loop.

Barua, Himel↗

A 1MHz Oak Ridge AC / DC Converter for UAV Contactless Charger Implementation

In this paper, a 1 MHz single-phase Oak Ridge Converter (ORC) AC/DC wireless power transfer (WPT) system is introduced for unmanned air vehicle (UAV) charging applications. The proposed advanced solution eliminates the design, weight, volume, and the cost of the power factor correcting (PFC) front-end rectifier compared to the conventional practices. Additionally, grid power quality requirements can be achieved with the presented innovative idea. With this method, single stage WPT primary side uses the hybrid grid frequency and high frequency (60 Hz and 1 MHZ) from ac source through the coupler coils and to UAV battery with GaN FETs. Experimental results of the single-phase system is presented to confirm the mathematical analyses with the source voltage of 110 VAC, RMS and output voltage of 40 VDC at 1 kW power with 6 inches air gap between couplers. The primary coupler consists of a ferrite-backed single-turn coil with a radius of 1.5 ft, and the secondary coupler is made with an air-core single-turn coil with radius of 1.2 ft. The system overall ac to dc efficiency is measured 77 % acquiring 0.99 power factor (PF) and 3.3 % current total harmonic distortion (THD) at 1 kW power.

Asa, Erdem↗

Design and Analysis of a 200 kW Dynamic Wireless Charging System for Electric Vehicles

Dynamic wireless charging of electric vehicles can significantly alleviate or eliminate range anxiety while reducing the required on-board battery capacity. To achieve an electric vehicle charging balance with minimal infrastructure costs, power transfer levels around 200 kW are required. In this paper, a system architecture with a modularized power electronics and optimized power transfer couplers was adopted to enable efficient power transfer. A DC/DC converter was used for secondary-side charging control of the battery. The system performance was validated in an experimental setup at 120 kW with 91.31% efficiency from the DC input on the primary side to the vehicle battery.

Xue, Lincoln↗

In-Package Common-Mode Filter for GaN Power Module with Improved Radiated EMI Performance

This paper discusses the impact of parasitic inductances on the electromagnetic interference (EMI) performance at radiated frequency and provides a new concept for high-frequency wide bandgap (WBG) power module package design with integrated π-type common mode filter (π-CMF). The connection parasitic-inductances of a π-type CMF model are analyzed, and the parasitic inductances from the CMF to the CM noise source and to the heatsink are minimized to improve the CMF's EMI performance in the radiated frequency range. Therefore, placing the π-CMF closer to the power module (i.e. in-package CMF) provides a larger noise attenuation compared to placing it outside the module (i.e. external CMF). To verify the theoretical analysis, a half-bridge GaN power module with an in-package π-CMF is designed, and experiments are conducted by comparing the attenuated noise spectrums of a 70-V/1.75-A hard-switching buck converter built by the designed module with an external CMF and the power-module integrated CMF. According to the experiment results, up to 10 dBμV more attenuation is achieved by the in-package CMF than the external CMF, validating the analytical conclusion.

Xue, Lincoln↗

An Intelligent System for Automatic Selection of DC-DC Converter Topology with Optimal Design

In this paper, we present an intelligent system that has the capabilities of automatically selecting topology classes and optimizing circuit parameters of DC-DC power converters for a given design specification. The system, Machine-Learning-enhanced Automated Circuit Configuration and Evaluation of Power Converters (ML-ACCEPT), uses a hybrid of machine learning technologies, decision tree inference, reinforcement learning and deep neural networks. The system gives high accurate recommendations of design topology classes and computationally efficient results in optimizing power efficiencies in power converter design.

Xue, Lincoln↗

Deep Symbolic Optimization for Electric Component Sizing in Fixed Topology Power Converters

Power converters (PC) are a major component in any current electronic hardware device. The development and design is usually guided by expert knowledge and heavily relies on human intuition and experience. The process is a very time consuming and costly activity and it is generally hard to improve upon current designs. As a first step towards autonomous PC design, we are here proposing a new framework for the sizing of components for fixed topology PCs based on given design requirements. To this end, we developed surrogate models for rapid evaluation of new topologies and adapt the deep symbolic optimization (DSO) framework to generate new topologies guided by a reinforcement learning training signal. In an empirical evaluation, we show that our DSO based approach is able to find the optimal configuration for all investigated topologies, while reducing the learning time by at least a factor of 100 compared to popular RL algorithms.

Xue, Lincoln↗

Multiplexing-Based Flyback Converter for Multi-Port USB Power Delivery with True Power-Sharing

Universal serial bus power delivery (USB-PD) chargers are more attractive to consumers with multiple output ports. Existing multiple port charger designs take multi-stage approach thus increase power loss and charger size. Also, ports are normally designed with different power capability thus the high-power port becomes under-used if the connected device is fully charged while the other lower power ports cannot take over the unused power. This is mainly limited by the power architecture design. This paper addresses this issue by presenting a multiplexing based multi-port quasi-resonant flyback converter. The design achieves true power-sharing with high efficiency, small size, and simple analog implementation. This paper discusses the operating principle and design considerations. A GaN-based 60 W dual port charger verifies the proposed scheme while achieving 76% size reduction and 1% efficiency improvement than state-of-the-art.

Xue, Lincoln↗

Adaptive Time-Division Multiplexing Driving System for Solid State Lighting with Multiple Tunable Channels

Next generation solid state lighting enables unlimited control of light and serve much broader functions beyond the basic lighting for illuminance. The emerging lighting for productivity, well-being, healthcare, and growth have revolutionized the scope of lighting. To empower this unlimited controllability, a multi-channel tunable power-electronics driver is essential but has not been satisfactorily addressed so far. Existing solutions are lossy, large, and expensive, due to introduction of additional buck power conversion stages. This paper proposes a time-division multiplexing (TDM) LED driving system which eliminates those buck stages. The proposed design can directly pair with off-the-shelf pulse width modulated (PWM) controllers and since it inherits entire feature sets, it can achieve low loss at standby and at dimmed condition. The simple analog implementation avoids usage of expensive DSPs/MCU. GaN’s high switching frequency capability can push up the multiplexing frequency so a GaN-based flyback was built and proved the concept.

Xue, Lincoln↗

DC-Ripple-Energy Adaptive-Minimization (DREAM) Modulation Scheme for a High Power Density Inverter

The DC bus capacitor is one of the major power-density and reliability hurdles of electric drive systems. It is hard to shrink because it is constrained by the DC bus RMS ripple current, which is only load dependent. A dual-inverter based segmented drive can reduce the ripple current by ~50% compared to a non-segmented case. This paper analyzes the origin of this ripple current and points out the path for minimization. An optimal DC-ripple-energy adaptive-minimization (DREAM) modulation method is proposed to further reduce the ripple current. It is observed in experimental results that the proposed method can achieve additional 38% reduction over the traditional segmented drive system.

Xue, Lincoln↗

Modular Design of Receiver Side Power Electronics for 200 kW High Power Dynamic Wireless Charging System

Dynamic wireless power transfer (DWPT) can provide energy to EVs in motion and extend the drive range. By upscaling the charging power to 200 kW (High Power DWPT), the percentage of electrified roadway reduces and the solution becomes cost-effective. However, coil coupling-coefficient variation during vehicle movement fluctuates the transferred power which is unfavorable for vehicle battery. Secondary regulation design can smooth the power but the converter design becomes very challenging due to requirement in high power, high efficiency, fast control, as well as high power density since the unit will be onboard. This paper provides the modular design approach of a 200 kW secondary side unit to achieve high performance and scalability. The DC/DC converter using SiC devices demonstrated 98.3% efficiency.

Xue, Lincoln↗