Engineering Papers⌕ Search

Engineering topics

Wolf, M.

Publications and source records attributed to Wolf, M..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Lessons Learned from Flight Observations of the GOES-R Magnetometer

The Geostationary Operational Environmental Satellite (GOES)-16 observatory was launched on 19 November 2016. During daily on-orbit operations, shadowing of the inboard magnetometer sensor unit occurs due to spacecraft geometry and solar angle. Throughout the shadowing periods of the inboard magnetometer, anomalous excursions of 20 nanotesla (nT) are observed. In addition to the excursions during shadow events, the measurement difference between the inboard and outboard magnetometer varies over the day, indicating erroneous measurements by one or both magnetometers. In addition, based on the deployment rotations, the zero offsets of the X and Y axes were found to be significantly different, ~30nT, from ground calibration data. Because of these observations, an extensive root cause investigation was undertaken to correct the magnetometer system for the next spacecraft in the GOES-R series. This paper documents the efforts of that activity and the lessons learned as a result of the investigation.

Schnurr, R.↗
NASA NTRS2019

Lessons Learned from Flight Observations of the GOES-R Magnetometer

The Geostationary Operational Environmental Satellite (GOES)-16 observatory was launched on 19 November 2016. During daily on-orbit operations, shadowing of the inboard magnetometer sensor unit occurs due to spacecraft geometry and solar angle. Throughout the shadowing periods of the inboard magnetometer, anomalous excursions of 20 nanotesla (nT) are observed. In addition to the excursions during shadow events, the measurement difference between the inboard and outboard magnetometer varies over the day, indicating erroneous measurements by one or both magnetometers. In addition, based on the deployment rotations, the zero offsets of the X and Y axes were found to be significantly different, ~30nT, from ground calibration data. Because of these observations, an extensive root cause investigation was undertaken to correct the magnetometer system for the next spacecraft in the GOES-R series. This paper documents the efforts of that activity and the lessons learned as a result of the investigation.

GOES-R↗
NASA NTRS2010

Implications of Wind-Assisted Aerial Navigation for Titan Mission Planning and Science Exploration

The recent Titan Saturn System Mission (TSSM) proposal incorporates a montgolfiere (hot air balloon) as part of its architecture. Standard montgolfiere balloons generate lift through heating of the atmospheric gases inside the envelope, and use a vent valve for altitude control. A Titan aerobot (robotic aerial vehicle) would have to use radioisotope thermoelectric generators (RTGs) for electric power, and the excess heat generated can be used to provide thermal lift for a montgolfiere. A hybrid montgolfiere design could have propellers mounted on the gondola to generate horizontal thrust; in spite of the unfavorable aerodynamic drag caused by the shape of the balloon, a limited amount of lateral controllability could be achieved. In planning an aerial mission at Titan, it is extremely important to assess how the moon-wide wind field can be used to extend the navigation capabilities of an aerobot and thereby enhance the scientific return of the mission. In this paper we explore what guidance, navigation and control capabilities can be achieved by a vehicle that uses the Titan wind field. The control planning approach is based on passive wind field riding. The aerobot would use vertical control to select wind layers that would lead it towards a predefined science target, adding horizontal propulsion if available. The work presented in this paper is based on aerodynamic models that characterize balloon performance at Titan, and on TitanWRF (Weather Research and Forecasting), a model that incorporates heat convection, circulation, radiation, Titan haze properties, Saturn's tidal forcing, and other planetary phenomena. Our results show that a simple unpropelled montgolfiere without horizontal actuation will be able to reach a broad array of science targets within the constraints of the wind field. The study also indicates that even a small amount of horizontal thrust allows the balloon to reach any area of interest on Titan, and to do so in a fraction of the time needed by the unpropelled balloon. The results show that using the Titan wind field allows an aerobot to significantly extend its scientific reach, and that a montgolfiere (unpropelled or propelled) is a highly desirable architecture that can very significantly enhance the scientific return of a future Titan mission.

aerobot↗
NASA NTRS2000

Slowly rotating asteroid 1999 GU/sub 3

Optical and radar observations reveal that 1999 GU3 is subkilometer-sized object with a synodic period of 9.0 days, low visual and radar albedos, and colors more consistent with the ordinarychondrites than the vast majority of main-belt asteroids.

asteroids rotation photometry radar↗
NASA NTRS1999

Radar and Optical Observations of Asteroid 1998 KY26

Observations of near-Earth asteroid 1998 KY26 shortly after its discovery reveal a slightly elongated spheroid with a diameter of about 30 m, a composition analogous to carbonaceous chondritic meteorites, and a rotation period of 10.7 minutes, which is an order of magnitude shorter that that measured for any other solar system object.

radar asteroids near-Earth Asteroid 1998 KY26↗
NASA NTRS1987

Measurement of minority carrier lifetimes and surface recombination velocities in solar cells

A generic comparison has been carried out of all methods for recombination parameter determination that are based on measurement of a current and/or voltage in either steady-state, transient, or frequency-dependent approaches. The theoretical background for the time-dependent methods has been extended from prior work to include drift fields and be applicable to compound (multilayered) regions. The key findings were: (1) all methods have essentially the same limitations to determination of only the dominant recombination parameters; (2) open-circuit measurements have more sensitivity to the recombination parameters than short circuit measurements, but they present much more difficulty in eliminating spurious effects; (3) transient and frequency-dependent methods have exactly the same expressions for the relaxation constants and the breakpoint frequencies; and (4) in compound regions there exists only one set of relaxation constants for all the coupled layers. These constants include all relevant parameters of these layers. It is thus difficult to separate these parameters in time- or frequency-domain measurements. ASLBIC seems still to be the most suitable method for determination of emitter parameters.

Wolf, M.↗
NASA NTRS1986

Novel measurement techniques (development and analysis of silicon solar cells near 20% effciency)

Work in identifying, developing, and analyzing techniques for measuring bulk recombination rates, and surface recombination velocities and rates in all regions of high-efficiency silicon solar cells is presented. The accuracy of the previously developed DC measurement system was improved by adding blocked interference filters. The system was further automated by writing software that completely samples the unkown solar cell regions with data of numerous recombination velocity and lifetime pairs. The results can be displayed in three dimensions and the best fit can be found numerically using the simplex minimization algorithm. Also described is a theoretical methodology to analyze and compare existing dynamic measurement techniques.

Wolf, M.↗
NASA NTRS1985

Materials requirements for high-efficiency silicon solar cells

To achieve higher Si solar cell efficiencies (greater than 20%), better single-crystal Si must be produced. It is believed possible to bring Cz (Czochralski) Si up to the same low recombination level as FZ (Float Zone) Si. It is also desirable that solar cell Si meet the following requirements: long minority carrier lifetime (0.2 ohm-cm p-type with tau less than 500 microsec); repeatedly uniform lifetime (not spread from 50 to 1000 microsec); a lifetime that does not decrease during normal device processing; a silicon wafer sheet that is flat and stays throughout normal device processing; uniform and reasonable mechanical strength; and, manufacture at low cost (less than $50/sq m).

Wolf, M.↗
NASA NTRS1985

Advanced techniques for the measurement of multiple recombination parameters in solar cells

A survey of bulk recombination measurement techniques was presented. Classical methods were reviewed along with their limiting assumptions and simplifications. A modulated light measurement system was built and showed the large effects of junction capacitance. Techniques for extension of classical methods for measurement of multiparameter multiregression measurements were identified and analyzed.

Newhouse, M.↗
NASA NTRS1985

Silicon solar cell efficiency improvement: Status and outlook

Efficiency and operating life is an economic attribute in silicon solar cells application. The efficiency improvements made during the 30 year existence of the silicon solar cells, from about 6% efficiency at the beginning to 19% in the most recent experimental cells is illustrated. In the more stationary periods, the effort was oriented towards improving radiation resistance and yields on the production lines, while, in other periods, the emphasis was on reaching new levels of efficiency through better cell design and improved material processing. First results were forthcoming from the recent efforts. Considerably more efficiency advancement in silicon solar cells is expected, and the anticipated attainment of efficiencies significantly above 20% is discussed. Major advances in material processing and in the resulting material perfection are required.

Wolf, M.↗
NASA NTRS1984

Summary of the high-efficiency crystalline solar cell research forum

An outline is given listing the speeches given in each session and the pertinent points is some speeches. There were six session, besides the overview session they were: (1) high efficiency concepts; (2) surface/interface effects; (3) bulk effects; (4) modeling; and (5) high efficiency device processing. Besides the emphasis placed on increasing efficiency of energy conversion, a great amount of discussion was spent on ways to reduce recombination and reducing surface defects.

Wolf, M.↗
NASA NTRS1984

Lifetimes in Si CVD-epitaxial and other layers determined by spectral LBIC

In an effort to evaluate the minority carrier lifetimes in CVD-epitaxially grown layers in their dependence on the CVD process variables, the absolute spectral LBIC method was found to be the only available method capable of yielding both lifetime and surface recombination velocity in layers, independent of the resistivity of this layer or that of the substrate, as long as they are separated by a pn-junction. With this method, it was not only possible to determine the minority carrier lifetimes in as-grown epi-layers, but to observe their changes through the device fabrication processes. In addition, it was possible for the first time to determine the lifetimes in the alloy-regrowth p(+) layers of base high/low junction structures.

Wolf, M.↗
NASA NTRS1982

Analysis and evaluation in the production process and equipment area of the low-cost solar array project

It was found that the Solarex metallization design and process selection should be modified to yield substantially higher output of the 10 cm x 10 cm cells, while the Westinghouse design is extremely close to the optimum. In addition, further attention to the Solarex pn junction and base high/low junction formation processes could be beneficial. For the future efficiency improvement, it was found that refinement of the various minority carrier lifetime measurement methods is needed, as well as considerably increased sophistication in the interpretation of the results of these methods. In addition, it was determined that further experimental investigation of the Auger lifetime is needed, to conclusively determine the Auger coefficients for the direct Auger recombination at high majority carrier concentrations.

Wolf, M.↗
NASA NTRS1982

Research possibilities? No! Needs for research to make PV solar energy utilization broadly competitive

The historical progression of efficiency improvements, cost reductions, and performance improvements in modules and photovoltaic systems are described. The potential for future improvements in photovoltaic device efficiencies and cost reductions continues as device concepts, designs, processes, and automated production capabilities mature. Additional step-function improvements can be made as today's simpler devices are replaced by more sophisticated devices.

Wolf, M.↗
NASA NTRS1982

Comparison of various silicon sawing methods

The technology and economics of four methods of wafering silicon boules of large cross section are described. Slurry sawing using either blades or wires, and fixed abrasive sawing using the ID saw or by the FAST method, having the abrasive attached to wires which are arranged in a blade pack, are considered. The technical performance of each method is evaluated and cost/price estimates are summarized.

Wolf, M.↗
NASA NTRS1982

New silicon cell design concepts for 20 percent AMI efficiency

The basic design principles for obtaining high efficiency in silicon solar cells are reviewed. They critically involve very long minority carrier lifetimes, not so much to attain high collection efficiency, but primarily for increased output voltages. Minority carrier lifetime, however, is sensitive to radiation damage, and particularly in low resistivity silicon, on which the high efficiency design is based. Radiation resistant space cells will therefore have to follow differing design principles than high efficiency terrestrial cells.

Wolf, M.↗
NASA NTRS1981

Overview study of Space Power Technologies for the advanced energetics program

Space power technologies are reviewed to determine the state-of-the-art and to identify advanced or novel concepts which promise large increases in performance. The potential for incresed performance is judged relative to benchmarks based on technologies which have been flight tested. Space power technology concepts selected for their potentially high performance are prioritized in a list of R & D topical recommendations for the NASA program on Advanced Energetics. The technology categories studied are solar collection, nuclear power sources, energy conversion, energy storage, power transmission, and power processing. The emphasis is on electric power generation in space for satellite on board electric power, for electric propulsion, or for beamed power to spacecraft. Generic mission categories such as low Earth orbit missions and geosynchronous orbit missions are used to distinguish general requirements placed on the performance of power conversion technology. Each space power technology is judged on its own merits without reference to specific missions or power systems. Recommendations include 31 space power concepts which span the entire collection of technology categories studied and represent the critical technologies needed for higher power, lighter weight, more efficient power conversion in space.

Taussig, R.↗