Engineering Papers⌕ Search

Engineering topics

Wang, L

Publications and source records attributed to Wang, L.

At least 91 records · Page 5

Na27Ru14O48: A New Mixed-valence Sodium Ruthenate with Magnetic Heptameric Plaquettes

Na{sub 27}Ru{sub 14}O{sub 48} has been synthesized in air at 700 C. The composition and crystal structure of the phase were determined by single crystal X-ray diffraction. The triclinic crystal structure contains isolated planar Ru{sub 7}O{sub 24} plaquettes made from seven edge-sharing RuO{sub 6} octahedra. The complex Na:Ru ratio is a result of tilting of the plaquettes to disrupt the packing of nominally hexagonal close packed planes made of Na ions and RuO{sub 6} octrahedra. Resistivity measurements show that the material is semiconducting with an activation energy of 0.53 eV. The observed magnetic moment of 3.11 {micro}{sub B} per Ru is lower than the expected spin only value, but is within the range seen in other compounds and is too large to indicate that the fundamental magnetic entities are the isolated Ru{sub 7}O{sub 24} plaquettes. Small, reproducible deviations in the Curie-Weiss behavior occur below 200 K and the onset of a broad magnetic transition is seen between 40 and 32 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Deformation of Olivine at Subduction Zone Conditions Determined from In situ Measurements with Synchrotron Radiation

We report measurements of the deformation stress for San Carlos olivine at pressures of 3-5 GPa, temperatures of 25-1150 C, and strain rates of 10{sup -7}-10{sup -5} s{sup -1}. We determine a deformation stress of approximately 2.5 GPa that is relatively temperature and strain rate independent in the temperature range of 400-900 C. The deformation experiments have been carried out on a deformation DIA (D-DIA) apparatus, Sam85, at X17B2, NSLS. Powder samples are used in these experiments. Enstatite (MgSiO{sub 3}) (3-5% total quality of sample) is used as the buffer to control the activity of silica. Ni foil is used in some experiments to buffer the oxygen fugacity. Water content is confirmed by IR spectra of the recovered samples. Samples are compressed at room temperature and are then annealed at 1200 C for at least 2 h before deformation. The total (plastic and elastic) strains (macroscopic) are derived from the direct measurements of the images taken by X-ray radiograph technique. The differential stresses are derived from the diffraction determined elastic strains. In the regime of 25-400 C, there is a small decrease of stress at steady state as temperature increases; in the regime of 400 C to the 'transition temperature', the differential stress at steady state ({approx}2.5 GPa) is relatively insensitive to the changes of temperature and strain rate; however, it drastically decreases to about 1 GPa and becomes temperature-dependent above the transition temperature and thereafter. The transition temperature is near 900 C. Above the transition temperature, the flow agrees with power law creep measurements of previous investigations. The anisotropy of differential stress in individual planes indicates that the deformation of olivine at low temperature is dominated by [0 0 1](1 0 0). Accounting to a slower strain rate in the natural system, the transition temperature for the olivine in the slab is most likely in the range of 570-660 C.

58 GEOSCIENCES↗

Density and Elasticity of Zr46Cu37.6Ag8.4Al8 Bulk Metallic Glass at High Pressure

Compressional and shear wave velocities of Zr{sub 46}Cu{sub 37.6}Ag{sub 8.4}Al{sub 8} bulk metallic glass (BMG) have been measured up to 6.3 GPa at room temperature using ultrasonic interferometry in conjunction with synchrotron X-radiography. The densities at high pressures are uniquely determined using the measured velocities. The experimental results for the elastic moduli of Zr{sub 46}Cu{sub 37.6}Ag{sub 8.4}Al{sub 8} show a reasonable agreement with the Voigt-Reuss-Hill approximation of the element metal phases, indicating that the elastic properties of the BMG have a close correlation with its constituent components.

36 MATERIALS SCIENCE↗

Superhard Diamond/tungsten Carbide Nanocomposites

We investigated the processing conditions of diamond/tungsten carbide (WC) composites using in situ synchrotron x-ray diffraction (XRD) and reactive sintering techniques at high pressure and high temperatures. The as-synthesized composites were characterized by synchrotron XRD, scanning electron microscopy, high-resolution transmission electron microscopy, and indentation hardness measurements. Through tuning of the reaction temperature and time, we produced fully reacted, well-sintered, and nanostructured diamond composites with Vickers hardness of about 55 GPa and the grain size of WC binding matrix smaller than 50 nm. A specific set of orientation relationships between WC and tungsten is identified to gain microstructural insight into the reaction mechanism between diamond and tungsten.

36 MATERIALS SCIENCE↗

Observation of Anomalous Phonons in Orthorhombic Rare-earth Manganites

We observe the appearance of a phonon near the lock-in temperature in orthorhombic REMnO{sub 3} (RE denotes rare earth) (RE: Lu and Ho) and anomalous phonon hardening in orthorhombic LuMnO{sub 3}. The anomalous phonon occurs at the onset of spontaneous polarization. No such changes were found in incommensurate orthorhombic DyMnO{sub 3}. These observations directly reveal different electric polarization mechanisms in the E-type and incommensurate-type orthorhombic REMnO{sub 3}.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Structural Analysis of a Highly Glycosylated and Unliganded gp120-Based Antigen Using Mass Spectrometry

Structural characterization of the HIV-1 envelope protein gp120 is very important for providing an understanding of the protein's immunogenicity and its binding to cell receptors. So far, the crystallographic structure of gp120 with an intact V3 loop (in the absence of a CD4 coreceptor or antibody) has not been determined. The third variable region (V3) of the gp120 is immunodominant and contains glycosylation signatures that are essential for coreceptor binding and entry of the virus into T-cells. In this study, we characterized the structure of the outer domain of gp120 with an intact V3 loop (gp120-OD8) purified from Drosophila S2 cells utilizing mass spectrometry-based approaches. We mapped the glycosylation sites and calculated the glycosylation occupancy of gp120-OD8; 11 sites from 15 glycosylation motifs were determined as having high-mannose or hybrid glycosylation structures. The specific glycan moieties of nine glycosylation sites from eight unique glycopeptides were determined by a combination of ECD and CID MS approaches. Hydroxyl radical-mediated protein footprinting coupled with mass spectrometry analysis was employed to provide detailed information about protein structure of gp120-OD8 by directly identifying accessible and hydroxyl radical-reactive side chain residues. Comparison of gp120-OD8 experimental footprinting data with a homology model derived from the ligated CD4-gp120-OD8 crystal structure revealed a flexible V3 loop structure in which the V3 tip may provide contacts with the rest of the protein while residues in the V3 base remain solvent accessible. In addition, the data illustrate interactions between specific sugar moieties and amino acid side chains potentially important to the gp120-OD8 structure.

59 BASIC BIOLOGICAL SCIENCES↗

Acoustic Velocities and Elastic Properties of Pyrite (FeS2) to 9.6 GPa

Ultrasonic interferometry was utilized in conjunction with synchrotron-based X-ray diffraction and X-radiographic imaging to determine the compressional and shear wave velocities and unit-cell volumes of pyrite (FeS{sub 2}) at room temperature and pressures up to 9.6 GPa. Fitting all of the experimental volume and velocity data to third-order finite-strain equations yielded the adiabatic zero-pressure bulk and shear moduli and their first pressure derivatives: K{sub S0}=138.9(7) GPa, G{sub 0}=112.3(3) GPa, ({partial_derivative} K{sub S0}/{partial_derivative} P){sub T} =K{sub S0'}=6.0(1), ({partial_derivative}G{sub 0}/{partial_derivative}P){sub T} =G{sub 0'}=3.0(<1), where the numbers in parentheses represent the 1{sigma} uncertainty in the last significant digit. These results are in good agreement with several previous static compression studies on this material but differ quite strongly from the results obtained via first principles calculations. This study presents the first direct measurement of the bulk shear properties of this material.

58 GEOSCIENCES↗

Tunable Radiation Source by Coupling Laser-Plasma-Generated Electrons to a Periodic Structure

Near-infrared radiation around 1000 nm generated from the interaction of a high-density MeV electron beam, obtained by impinging an intense ultrashort laser pulse on a solid target, with a metal grating is observed experimentally. Theoretical modeling and particle-in-cell simulation suggest that the radiation is caused by the Smith-Purcell mechanism. The results here indicate that tunable terahertz radiation with tens GV/m field strength can be achieved by using appropriate grating parameters.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Recommendation for Mitigations of the Electron Cloud Instability in the ILC

Electron cloud has been identified as one of the highest priority issues for the international Linear Collider (ILC) Damping Rings (DR). An electron cloud Working Group (WG) has evaluated the electron cloud effect and instability, and mitigation solutions for the electron cloud formation. Working group deliverables include recommendations for the baseline and alternate solutions to the electron cloud formation in various regions of the ILC Positron DR, which is presently assumed to be the 3.2 km design. Detailed studies of a range of mitigation options including coatings, clearing electrodes, grooves and novel concepts, were carried out over the previous several years by nearly 50 researchers, and the results of the studies form the basis for the recommendation. The recommendations are the result of the working group discussions held at numerous meetings and during a dedicated workshop. In addition, a number of items requiring further investigation were identified during the discussions at the Cornell meeting and studies will be carried out at CesrTA, a test accelerator dedicated to electron cloud studies, and other institutions.

43 PARTICLE ACCELERATORS↗

Ideas for a Future PEP-X Light Source

SLAC is developing a long-range plan to transfer the evolving scientific programs at SSRL from the SPEAR3 light source to a much higher performing synchrotron source -- PEP-X -- a new storage ring that would occupy the existing PEP-II tunnel and support two experimental halls, each containing 16 x-ray beam lines. Operating at 4.5 GeV and 1.5 A with a horizontal emittance of 0.14 nm-rad, reached using 90 m of damping wigglers, PEP-X would have an order of magnitude higher average brightness and flux in the 1-{angstrom} x-ray range than any existing or planned future storage ring sources. Higher brightness in the soft x-ray regime might be reached with partial lasing in long undulators, and high peak brightness could be reached with seeded FEL emission. The status of preliminary studies of PEP-X is presented.

43 PARTICLE ACCELERATORS↗

High-pressure phase transformations in MgO-Y2O3 nanocomposites

Temperature and pressure dependence of phase evolution in 0.5 MgO-0.5 Y{sub 2}O{sub 3} is studied using the diamond anvil method. At 300 K and 5.5 GPa, transformations in Y{sub 2}O{sub 3} are observed, resulting in co-existence of cubic, hexagonal, and monoclinic phases. Heating to 1293 K results in increased crystallinity and increase in hexagonal and monoclinic phase content. Isothermal and isobaric hold at 1273 K and 5.5 GPa for 120 min results in yttrium dissolution in cubic MgO, causing 0.83% volumetric strain. Cooling to 300 K and 0 GPa yields a four phase co-existence among cubic MgO and cubic, hexagonal, and monoclinic Y{sub 2}O{sub 3}. The residual MgO unit cell volume expansion is 0.67% at 300 K, indicating solid solution formation. Aging of the nanocomposites for 240 h does not change the observed 4 phase co-existence.

42 ENGINEERING↗

Suppression of Beam-Ion Instability in Electron Rings with Multi-Bunch Train Beam Fillings

The ion-caused beam instability in the future light sources and electron damping rings can be serious due to the high beam current and ultra-small emittance of picometer level. One simple and effective mitigation of the instability is a multi-bunch train beam filling pattern which can significantly reduce the ion density near the beam, and therefore reduce the instability growth rate up to two orders of magnitude. The suppression is more effective for high intensity beams with low emittance. The distribution and the field of trapped ions are benchmarked to validate the model used in the paper. The wake field of ion-cloud and the beam-ion instability is investigated both analytically and numerically. We derived a simple formula for the build-up of ion-cloud and instability growth rate with the multi-bunch-train filling pattern. The ion instabilities in ILC damping ring, SuperKEKB and SPEAR3 are used to compare with our analyses. The analyses in this paper agree well with simulations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Trapping of Electron Cloud LLC/Cesrta Quadrupole and Sextupole Magnets

The Cornell Electron Storage Ring (CESR) has been reconfigured as an ultra low emittance damping ring for use as a test accelerator (CesrTA) for International Linear Collider (ILC) damping ring R&D [1]. One of the primary goals of the CesrTA program is to investigate the interaction of the electron cloud with low emittance positron beam to explore methods to suppress the electron cloud, develop suitable advanced instrumentation required for these experimental studies and benchmark predictions by simulation codes. This paper reports the simulation of the electron-cloud formation in CESRTA and ILC quadrupole and sextupole magnets using the 3D code CLOUDLAND. We found that electrons can be trapped with a long lifetime in a quadrupole and sextupole magnet due to the mirror field trapping mechanism. We study the effects of magnet strength, bunch current, ante-chamber effect, bunch spacing effect and secondary emission yield (SEY) in great detail. The development of an electron cloud in magnets is the main concern where a weak solenoid field is not effective. Quadrupole and sextupole magnets have mirror field configurations which may trap electrons by the mirror field trapping mechanism [2]. Fig.1 shows the orbit of a trapped electron in a quadrupole magnet. The electron makes gyration motion (called transverse motion) and also moves along the field line (called longitudinal motion). At the mirror point (middle of the field line), there is a maximum longitudinal energy and minimum transverse energy. When the electron moves away from the mirror point, its longitudinal energy reduces and the transverse energy increases as the magnetic field increases. If the magnetic field is strong enough, the longitudinal energy becomes zero at one point and then the electron is turned back by the strong field. Note that the electrons are trapped in the region near the middle of the field lines. Although all quadrupole and sextupole magnets can trap electrons in principle, the trapping mechanism is also greatly sensitive to the detail dynamics of the electrons [3]. Both the positron beam and the spacing charge force of electron cloud itself play important roles. This paper reports the simulation of electron cloud in CESRTA/ILC quadrupole and sextupole magnets. Table 1 shows the main parameters used in the simulation.

43 PARTICLE ACCELERATORS↗