Engineering topics

Tewari, S. N.

Publications and source records attributed to Tewari, S. N..

At least 37 records · Page 2

NASA NTRS1992

Macrosegregation During Steady-State Arrayed Growth of Dendrites in Directionally Solidified Pb-Sn Alloys

The paper examines the growth parameter dependence of the longitudinal macrosegregation due to interdendritic thermosolutal convection during directional solidification of Pb-Sn alloys with a steady-state dendritic arrayed morphology. The experimentally observed longitudinal macrosegregation can be described by an empirical parameter, effective partition coefficient (kE), obtained from Cs = kEC0(1 - fs) super KI-1, where the original tin content is C0 and that corresponding to the fraction distance solidified (Fs) is Cs. Channel formation is strongly associated with the onset of thermosolutal convection in the interdendritic melt. The critical effective Rayleigh number for the onset of channel formation is about 0.07.

Tewari, S. N.↗

NASA NTRS1992

Indirect Calibration In Electron-Probe Microanalysis

Technique for indirect calibration in electron-probe microanalysis reduces number of measurements needed without significantly degrading precision of measurement data. Advantageous when many analyses must be performed; for example, determining varying chemical composition at many positions across specimen of multicomponent alloy. Time spent acquiring data reduced considerably.

Terepka, F. M.↗

NASA NTRS1992

Break-down of a planar liquid-solid interface during directional solidification - Influence of convection

The influence of convection on the development of morphological instability at the liquid-solid interface during directional solidification in a positive thermal gradient has been examined in Pb-10 wt pct Sn and succinonitrile-1.9 wt pct acetone. The onset of interfacial breakdown occurs at higher growth speeds in the presence of convection. The linear stability analysis due to Favier and Rouzaud which uses the 'deformable' mass flow boundary layer concept shows a good agreement with the experimentally observed behavior.

Tewari, S. N.↗

NASA NTRS1991

Growth-speed dependence of primary arm spacings in directionally solidified Pb-10 wt pct Sn

The dependence of primary arm spacings on growth speed has been investigated for cellular and dendritic arrays in directionally solidified Pb-10 wt pct Sn. The spatial arrangements of cells and dendrites, as given by their coordination number, are not very different from each other. The primary arm spacing maxima and the cell-to-dendrite transition appear to be strongly influenced by the magnitude of the solute partition coefficient (k). The planar-to-cellular transition in Pb-Sn (k = 0.50) is supercritical as compared to the subcritical behavior reported in Al-Cu (k = 0.14) and succinonitrile-acetone (k = 0.1).

Chopra, M. A.↗

NASA NTRS1991

Macrosegregation during plane front directional solidification of Csl-1 wt. percent Tll alloy

Macrosegregation produced during vertical Bridgeman directional solidification of Csl-1 wt. pct. Tll in crucibles of varying diameter, from 0.5 to 2.0 cm, was examined. Gravity driven convection is present in the melt even in the smallest crucible diameter of 0.5 cm. Observed solutal profiles are in agreement with the analytical boundary layer model of Favier which describes macrosegregation in the presence of convection. The scintillation efficiency of Csl decreases along the specimen length as the thallium iodide content of the alloy increases.

Sidawi, I. M. S.↗

NASA NTRS1990

Dentritic morphology and microsegregation in directionally solidified superalloy, PWA-1480, single crystal: Effect of gravity; center director's discretionary fund report

Primary dendrite spacings, secondary dendrite spacings, and microsegregation have been examined in PWA-1480 single crystal specimens which were directionally solidified during parabolic maneuvers on the KC-135 aircraft. Experimentally observed growth rate and thermal gradient dependence of primary dendrite spacings are in good agreement with predictions from dendrite growth models for binary alloys. Secondary dendrite coarsening kinetics show a reasonable fit with the predictions from an analytical model proposed by Kirkwood for a binary alloy. The partition coefficients of tantalum, titanium, and aluminum are observed to be less than unity, while that for tungsten and cobalt are greater than unity. This is qualitatively similar to the nickel base binaries. Microsegregation profiles experimentally observed for PWA-1480 superalloy show a good fit with Bower, Brody, and Flemings model developed for binary alloys. Transitions in gravity levels do not appear to affect primary dendrite spacings. A trend of decreased secondary arm spacings with transition from high gravity to the low gravity period was observed at a growth speed of 0.023 cm s(exp -1). However, definite conclusions can only be drawn by experiments at lower growth speeds which make it possible to examine the side-branch coarsening kinetics over a longer duration. Such experiments, not possible due to the insufficient low-gravity time of the KC-135, may be carried out in the low-gravity environment of space.

Tewari, S. N.↗

NASA NTRS1990

Effect of thermosolutal convection on the solid-liquid interface in Pb-Au alloy

Liquid-solid interface distortion in the region of primary dendrite tips has been investigated in directionally solidified Pb-8 wt pct Au alloy. The distortions are caused by thermosolutal convection despite choice of growth conditions which should have been thermally and solutally stabilizing. The convection produces clustering of primary dendrites on a plane perpendicular to the growth direction. It produces a mushy zone, where the primary dendrites do not protrude with a uniform length, across the specimen cross section, resulting in large macrosegregation in the transverse direction. However, little macrosegregation is observed along the growth direction. The mushy zone, with uneven dendrite lengths, forms in the beginning of directional solidification. Its shape and dendrite distribution do not show much change during subsequent solidification. Tip morphologies of primary dendrites, within the dendrite clusters, appear to follow the morphological stability relationship.

Tewari, S. N.↗

NASA NTRS1990

Primary arm spacing in directionally solidified Pb-10 wt percent Sn alloys

The dependence of primary arm spacings on growth speed was investigated for cellular and dendritic arrays in Pb-10 wt percent Sn samples directionally solidified under a constant positive thermal gradient in the melt. The gradient of constitutional supercooling was varied from almost zero (near the break-down of the planar liquid-solid interface at small growth speeds, cellular morphology) to near unity (large growth speeds, dendritic morphology). The spatial arrangements of cells and dendrites, as given by their coordination number, are not very different from each other. It appears that primary arm spacing maxima and the cell to dendrite transition are strongly influenced by the magnitude of the solute partition coefficient. The planar to cellular bifurcation is supercritical in Pb-Sn which has a high partition coefficient, as compared to the subcritical behavior reported in Al-Cu and succinonitrile-acetone, both of which have low partition coefficients. The primary arm spacing model due to Hunt agrees with the experimentally observed trend for the whole growth regime. There is a good quantitative agreement at higher gradients of supercooling. However, the model overpredicts the primary arm spacings at low gradients of constitutional supercooling.

Chopra, M. A.↗

NASA NTRS1990

Secondary arm coarsening and microsegregation in superalloy PWA-1480 single crystals: Effect of low gravity

Single crystal specimens of nickel base superalloy PWA-1480 were directionally solidified on ground and during low gravity (20 sec) and high gravity (90 sec) parabolic maneuver of KC-135 aircraft. Thermal profiles were measured during solidification by two in-situ thermocouples positioned along the sample length. The samples were quenched during either high or low gravity cycles so as to freeze the structures of the mushy zone developing under different gravity levels. Microsegregation was measured by examining the solutal profiles on several transverse cross-sections across primary dendrites along their length in the quenched mushy zone. Effect of gravity level on secondary arm coarsening kinetics and microsegregation have been investigated. The results indicate that there is no appreciable difference in the microsegregation and coarsening kinetics behavior in the specimens grown under high or low gravity. This suggests that short duration changes in gravity/levels (0.02 to 1.7 g) do not influence convection in the interdendritic region. Examination of the role of natural convection, in the melt near the primary dendrite tips, on secondary arm spacings requires low gravity periods longer than presently available on KC-135. Secondary arm coarsening kinetics show a reasonable fit with the predictions from a simple analytical model proposed by Kirkwood for a binary alloy.

Vijayakumar, M.↗

NASA NTRS1990

Primary arm spacing in directionally solidified Pb-10 wt pct Sn alloys

The dependence of primary arm spacings on growth speed was investigated for cellular and dendritic arrays in Pb-10 wt percent Sn samples directionally solidified under a constant positive thermal gradient in the melt. The gradient of constitutional supercooling was varied from almost zero (near the break-down of the planar liquid-solid interface at small growth speeds, cellular morphology) to near unity (large growth speeds, dendritic morphology). The spatial arrangements of cells and dendrites, as given by their coordination number, are not very different from each other. It appears that primary arm spacing maxima and the cell to dendrite transition are strongly influenced by the magnitude of the solute partition coefficient. The planar to cellular bifurction is supercritical in Pb-Sn which has a high partition coefficient, as compared to the subcritical behavior reported in Al-Cu and succinonitrile-acetone, both of which have low partition coefficients. The primary arm spacing model due to Hunt agrees with the experimentally observed trend for the whole growth regime. There is a good quantitative agreement at higher grdients of supercooling. However, the model overpredicts the primary arm spacings at low gradients of constitutional supercooling.

Chopra, M. A.↗

NASA NTRS1989

Calibration approach to electron probe microanalysis: A study with PWA-1480, a nickel base superalloy

The utility of an indirect calibration approach in electron probe microanalysis is explored. The methodology developed is based on establishing a functional relationship between the uncorrected k-ratios and the corresponding concentrations obtained using one of the ZAF correction schemes, for all the desired elements in the concentration range of interest. In cases where a very large number of analyses are desired, such a technique significantly reduces the total time required for the microprobe analysis without any significant loss of precision in the data. A typical application of the method in the concentration mapping of the transverse cross-section of a dendrite in directionally solidified PWA-1480, a nickel-based superalloy, is described.

Terepka, F. M.↗

NASA NTRS1989

Side branch morphology and coarsening in directionally solidified Pb-8.4 at. pct Au

The scaling relationships among the morphological features associated with the formation of perturbations (side branches) in the intercellular regions of a directionally solidified Pg-8.4 at. pct Au alloy were investigated. It is shown that the ratio between the initial side-branch spacing near dendrite tips, lambda-2, and the dendrite-tip radius, r(t), equals 2 to 2.5. The ratio between the distance from the dendrite tip to the location of the first side branch formation, lambda(p), and the t(r) equals 8 to 10. It was found that the model proposed by Kirkwood (1985) for the secondary dendrite arm coarsening shows a very good quantitative fit to the experimentally observed secondary arm coarsening kinetics during directional solidification.

Tewari, S. N.↗

NASA NTRS1988

Effect of melt spinning on grain size and texture in Ni-Mo alloys

Chill-block melt-spun ribbons of Ni-Mo alloys with Mo contents of 8 to 41.8 wt pct have been examined for microstructure and texture dependence on processing conditions. Linear features observed in grains solidified with a planar liquid-solid interface at the quench side of the ribbons have been identified to be due to the twins on the (111)gamma plane formed during solidification. Grain size variation with the wheel surface speed and the alloy composition has been studied. The crystallographic texture on the quench side and the free surface side of the ribbons has been investigated.

Tewari, S. N.↗

NASA NTRS1988

Microsegregation in directionally solidified Pb-8.4 at. pct Au alloy

The dependence of microsegregation behavior on growth rate and thermal gradient has been examined in a Pb-8.4 at. pct Au alloy material partially directionally solidified and quenched. The composition of the quenched 'liquid' at the dendrite tip (Ct), that of the eutectic-like solid phase freezing from the interdendritic liquid at the base of dendrite (Cse), the volume fraction of this eutectic-like region (fe), and solute profiles in the interdendritic quenched liquid and ahead of the dendrite have been measured. Two dendritic growth models for solidification of a binary alloy melt in a positive thermal gradient at the liquid-solid interface, one for dendrites with 'minimum undercooled dendrite tip' and the other for an Ivantsov type of dendrite with 'marginally stable tip', have been examined for a quantitative comparison with measured values of Ct, Cse, and fe. Convection in the melt, possibly due to horizontal density gradients, is found to be a serious limitation for theoretical understanding of the observed experimental behavior and meaningful comparison of theories.

Tewari, S. N.↗

NASA NTRS1987

Cellular microstructure of chill block melt spun Ni-Mo alloys

Chill block melt spun ribbons of Ni-Mo binary alloys containing 8.0 to 41.8 wt pct Mo have been prepared under carefully controlled processing conditions. The growth velocity has been determined as a function of distance from the quench surface from the observed ribbon thickness dependence on the melt puddle residence time. Primary arm spacings measured at the midribbon thickness locations show a dependence on growth velocity and alloy composition which is expected from dendritic growth models for binary alloys directionally solidified in a positive temperature gradient. Microsegregation across cells and its variation with distance from the quench surface and alloy composition have been examined and compared with theoretical predictions.

Tewari, S. N.↗

NASA NTRS1987

Effect of undercooling on the microstructure of Ni-35 at. pct Mo (eutectic) and Ni-38 at. pct Mo (hypereutectic) alloys

Ni-35 at. pct Mo and Ni-38 at. pct Mo alloy specimens have been solidified from various levels of undercooling in the differential thermal analysis and the electromagnetic levitation units in a pyrex/vycor bed. The evolution of the microstructure in the solified specimens has been examined in terms of the degree of undercooling, the nature of the first phase to nucleate from the melt, and the specimen cooling rate. The melt has been observed to undercool more in the presence of intermetallic NiMo (beta) phase as compared to that in the presence of nickel-rich solid solution (gamma). The 'anomalous eutectic' type of microstructure has been shown to result from the initial formation of the dendritic skeleton of either of the two phases, its segmentation due to convection and ripening, and the subsequent nucleation of the other phase in the interdendritic liquid regions. The recalescence behavior has been examined as a function of undercooling and the nature of the phase nucleating first in the melt.

Tewari, S. N.↗

NASA NTRS1987

Effect of heat treatment on the fracture behaviour of directionally solidified (gamma/gamma-prime)-alpha alloy

An investigation is conducted into the influence of various heat treatments on the work of fracture and its relation to microstructure for a directionally solidified Ni-33Mo-5.7Al (wt pct) (gamma/gamma-prime)-alpha alloy. The jagged crack propagation observed is due to delamination of the ligaments and associated plastic deformation. Fracture behavior is examined with respect to alloy microstructures and load-deflection curves. The four heat-treatment conditions considered are: (1) as-directionally solidified, (2) solutionized, (3) directionally solidified and thermally cycled, and (4) solutionized and thermally cycled.

Sriramamurthy, A. M.↗

NASA NTRS1987

A critical examination of the dendrite growth models Comparison of theory with experimental data

Three dendrite growth models for directionally solidified succinonitrile-acetone, succinonitrile-salol, aluminum-copper, and lead-paladium alloys are evaluated. The characteristics of the Burden and Hunt (1974) model, the Laxmanan (1985) model, and the Trivedi (1980) model are described. The dendrite tip temperature, tip radius, liquid composition, and primary arm spacing for the alloys are analyzed in terms of growth speed, alloy composition, and temperature gradient. It is observed that the Burden and Hunt model accurately predicts the proper behavior of the parameters, but does not provide good quantitative predictions. A good fit between the experimental data and the Trivedi and Laxmanan models is detected. The advantages of the Trivedi marginal stability analysis and the Laxmanan minimum dendrite tip undercooling approaches are discussed.

Tewari, S. N.↗