Engineering Papers⌕ Search

Engineering topics

Stempien, John D

Publications and source records attributed to Stempien, John D.

At least 19 records

Micro-tensile Properties of Fueled Irradiated AGR-2 TRISO-coated Particle Buffer, IPyC, and SiC Interlayer Regions

Tristructural isotropic (TRISO) coated nuclear fuel particles are proving to be a versatile fuel form for new reactor designs. Understanding the bounding strength and failure mode of each coating interface is important to both fuel quality evaluation and failure prediction. A mechanism of key significance is failure of the silicon carbide (SiC) layer to retain fission products due to incomplete tearing of the buffer layer. This is a two-step mechanism involving both mechanical failure in the buffer and inner pyrolytic carbon (IPyC) layers and degradation of the SiC layer through palladium silicides at the IPyC-SiC interface. However, the mechanical properties of TRISO particle coating layers have yet to be fully characterized due to the small dimension of TRISO fuel particles and high radioactivity. To investigate this mechanism, in situ micro-tensile properties of the buffer, IPyC, SiC, buffer-IPyC, and IPyC-SiC interlayer regions of fueled TRISO particles have been tested at both as-fabricated and irradiated conditions. Determination of the mechanical properties of these TRISO particle regions will lead to a better understanding of the SiC layer failure mechanism and enable progress towards TRISO fuel qualification.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Radial Deconsolidation Leach-Burn-Leach of Five AGR-3/4 TRISO Fuel Compacts after Post-Irradiation Heating Tests

Five AGR-3/4 fuel compacts were previously heated in the Fuel Accident Condition Simulator (FACS) furnace. Three of these compacts were also reirradiated in the Neutron Radiography (NRAD) reactor before the FACS tests. One of these was heated to 1200°C, two were heated to 1400°C, one was heated to 1600°C, and one was held for a period of time at 1600 and 1700°C. After these FACS tests, the compacts were subjected to destructive post-irradiation examination (PIE) via radial-deconsolidation-leach-burn-leach (RDLBL) at INL. The RDLBL process deconsolidated the compacts in multiple radial steps, followed by a final, single-step axial deconsolidation. The samples generated at each step were analyzed for isotopes of key fission products and actinides. After each deconsolidation step, the compact volume was assessed, and this was used to normalize the measured quantities of nuclides of interest to give volumetric concentrations as a function of radial position within the compact. The total inventories of measured fission products and actinides and the radial concentration profiles were compared with their sibling compacts within the same capsule (similar irradiation conditions) that went through RDLBL in the as-irradiated state. These data will be used to refine the fission product transport models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-irradiation Heating Tests of As-Irradiated AGR-3/4 TRISO Fuel Compacts

Four post-irradiation heating tests of fuel compacts from the U.S. Advanced Gas Reactor (AGR)-3/4 irradiation experiment were completed. In addition to tristructural isotropic (TRISO)-coated driver fuel, each compact contained designed-to-fail (DTF) particles with fuel kernels coated only in pyrocarbon so as to simulate exposed kernels. Tests at 1600/1700°C, 1400°C, and 1200°C were performed to measure fission product release as a function of time and temperature. Silver release was highest in the 1200°C test, supporting the observation that silver release rates are highest in the 1100–1300°C range. Compared to tests of AGR-1 compacts with no exposed kernels, the Cs-134 and Kr-85 releases were noticeably higher in AGR-3/4. The exposed kernels’ contributions to Eu and Sr release are inconclusive, due to the difficulty in distinguishing among the combined effects of higher irradiation temperatures in these particular AGR-3/4 compacts, the presence of the DTF particles, and the Fuel Accident Condition Simulator (FACS) test temperatures. These data can be used to make inferences about fission product retention in exposed kernels as a function of time and temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR-5/6/7 PIE Overview 2024

This is a status update and description of major post-irradiation examination activities under the DOE's AGR TRISO fuel program. This presentation will be given at the annual program review hosted by INL the week of July 15.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR Fuel Oxidation Testing Summary and Plans

This presentation describes the goals, scope, and plans for oxidation testing of (primarily irradiated) AGR TRISO fuels and related materials (such as graphite and graphitic matrix material). This presentation will be given at the annual program review meeting for the Gas-cooled Reactor program hosted at INL starting on July 16.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Radial Deconsolidation and Leach-Burn-Leach of Eight As-Irradiated AGR-3/4 TRISO Fuel Compacts

Eight as-irradiated AGR-3/4 fuel compacts were subjected to destructive post-irradiation examination via radial-deconsolidation-leach-burn-leach (RDLBL) at INL. The RDLBL process deconsolidated the compacts in multiple, radial steps, followed by a final, single-step axial deconsolidation. The samples generated at each step were analyzed for isotopes of key fission products and actinides. After each deconsolidation step, the compact volume was assessed, and this was used to normalize the measured quantity of nuclides of interest to give a volumetric concentration as a function of radial position within the compact. The total inventories of measured fission products and actinides and the radial concentration profiles were compared among the eight compacts deconsolidated at INL and four other as-irradiated compacts examined at ORNL. The results were analyzed for the effects of irradiation temperature. These results will be used for comparisons with fission product transport models and as input from which fission product diffusivities can be calculated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR TRISO Fuel Fission Product Release Data Summary

Knowledge of fission product retention in and release from TRISO fuel under normal and off-normal conditions is needed for reactor safety analyses. This is important for coated-particle fuel used in high-temperature reactors relying on the functional containment strategy. Data on the release and retention of key fission products (e.g., Ag-110m, Cs-134, Eu-154, and Sr-90) in AGR UCO TRISO fuels have been summarized in this report, and empirical relationships with respect to time and temperature were developed. This included fission product accumulation in the OPyC and compact graphitic matrix during irradiation, release from compacts during irradiation, and release during post-irradiation safety testing at temperatures from 1600-1800°C. The frequencies of SiC failure and TRISO coating failure from irradiation and post-irradiation safety testing were also summarized as they have bearing on the quantities of Cs release from the fuel. In a forthcoming publication, a framework for combining and using these empirical relationships as part of a source term analysis will be presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Irradiated AGR 5/6/7 Compact 5-6-2 Examination Plan

This plan describes the post irradiation examination (PIE) activities to be performed by Oak Ridge National Laboratory (ORNL) on irradiated Compact 5-6-2 taken from the Advanced Gas Reactor (AGR) experiment, AGR 5/6/7. This work will be performed in accordance with the general objectives outlined in the AGR 5/6/7 PIE Plan and guidance in the ORNL PIE Statement of Work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Catalyzed oxidation of nuclear graphite by simulated fission products Sr, Eu, and I

The influence of three fission products Sr, Eu, and I on the oxidation of IG-110 nuclear graphite was studied in the temperature range of 400 to 1000 °C. Sr and Eu were introduced as chlorides, and I was introduced as NaI. The temperature dependence of both CO 2 and CO production during the graphite oxidation measured with mass spectroscopy and infrared spectrometry shows that the introduction of these three compounds to graphite significantly decreases the onset temperature for the oxidation of graphite. Among the three compounds, NaI is the most active towards the oxidation reaction, characterized by a significant decrease of the onset temperature from approximately 650 to 400 °C before and after its introduction to graphite. Separate measurements of CO 2 and CO concentration at varying temperatures enable the calculation of the activation energy for the formation of CO 2 and CO. The activation energies for the oxidation of pure and fission product-impregnated graphite samples decrease in the following order: standard IG-110 graphite, EuCl 3 -impregnated IG-110, SrCl 2 -impregnated IG-110, and NaI-impregnated IG-110. This trend indicates that the three compounds catalyze the oxidation of graphite at temperatures relevant to the operation of high-temperature gas-cooled reactors. Furthermore, it is found that the three compounds can also affect the molar ratio of reaction products CO 2 and CO, and the rates of the graphite oxidation. At temperatures higher than about 850 °C, the impregnated samples exhibit lower CO 2 : CO ratios than the pure graphite. Different from EuCl 3 and NaI, the introduction of SrCl 2 decreases the graphite oxidation rates at temperatures higher than about 770 °C. Their catalytic mechanism can be understood based on a redox cycle of the intermediate active species, promoting the dissociation of molecular oxygen and transfer to the carbon.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Irradiated AGR 5/6/7 Compact 4-1-3 Examination Plan

This plan describes the post irradiation examination (PIE) activities to be performed by Oak Ridge National Laboratory (ORNL) on irradiated Compact 4-1-3 taken from the Advanced Gas Reactor (AGR) experiment, AGR 5/6/7. This work will be performed in accordance with the general objectives outlined in the AGR 5/6/7 PIE Plan and guidance in the ORNL PIE Statement of Work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comparison of AGR-3/4 Fission Product Transport Model to Measurements and Extraction of Diffusivities via Analytical Fits

A one-dimensional finite-element model based on the MOOSE framework has been constructed, and overall transport estimates are predicted based on available diffusivities and sorption isotherms in the extant literature. The predicted transport profiles are compared to experimental results, where such results are available, including total inventory analysis of gamma emitters, liquid scintillation results for Sr-90 concentrations, radial deconsolidation leach-burn-leach within compacts, tomographic reconstructions based on detailed gamma scanning and destructive physical sampling of several rings. The magnitude of expected transport to the sink ring is generally predicted by the model for silver and cesium, however, modeled detailed concentration profiles are not consistent with experimental results. Strontium and europium transport is not well characterized by model results.

07 ISOTOPE AND RADIATION SOURCES↗

Exposed Kernel Heating Tests

Presentation on cracked AGR-2 TRISO particles and AGR-3/4 compacts subjected to FACS tests with and without prior reirradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Initial Observations from AGR 5/6/7 Capsule 1

The fourth and final irradiation experiment in the Advanced Reactor Technologies (ART) Advanced Gas Reactor (AGR) fuel development and qualification program is designated as AGR-5/6/7. Data collected from the fabrication, irradiation, and post-irradiation examination (PIE) of this tristructural isotropic (TRISO) fuel are intended to serve as the primary data set for the qualification of this fuel for use in high-temperature gas-cooled reactors (INL 2021, Collin 2018b). However, data collected from the three preceding irradiations (i.e., AGR-1, AGR-2, and AGR-3/4) may also be used to supplement data collected from AGR-5/6/7. All components of the AGR-5/6/7 fuel (i.e., UCO kernels, TRISO coatings, and fuel compacts) were produced on an engineering scale at BWXT (Lynchburg, Virginia USA) according to the fuel specification (Marshall 2017). This fuel was irradiated in the northeast flux trap (NEFT) at the Advanced Test Reactor (ATR) at Idaho national Laboratory (INL) from February 16, 2018 to July 22, 2020 (Pham et al. 2021). Measurements in the fission product monitoring system (FPMS) indicated unexpected and significant numbers of failures of TRISO particles in Capsule 1 near the end of the sixth irradiation cycle (ATR Cycle 166A). In the fourth cycle (ATR Cycle 164B) and beyond, the sweep gas flow became very low (presumably from degradation of the capsule gas outlet line via an unidentified mechanism), and the program deliberately isolated Capsule 1 from gas flow periodically. In later cycles, attempts to reestablish any kind of flow in Capsule 1 were unsuccessful. With little or no flow through Capsule 1, FPMS measurements and enumerations of failed particles in Capsule 1 were difficult or impossible as was the ability to control the helium/neon gas mixture used for temperature control. Gas flows and fission gas activity in the effluent gas from the other AGR-5/6/7 capsules were also impacted by the Capsule 1 gas flow issues and the large increase in fission gas released from the Capsule 1.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

EPMA-Based Mass Balance Method for Quantitative Fission Product Distribution Comparison between TRISO Particles

Two irradiated AGR-2 TRISO particles were chosen to demonstrate a recently developed mass balance technique in which EPMA-generated concentration data was used to determine fission product mass on a layer-by-layer basis in TRISO particles. EPMA-calculated fission product masses for most fission products in the two particles were within +/- 20% of their ORIGEN-modelled masses. Results show that Sr, Ba, and Eu accumulate preferentially in the carbon-rich kernel periphery on the particles’ side that lacks a gap between the buffer and IPyC. In addition, the more mobile elements--Cs, Sr, and Pd, accumulate in greater quantity in the outer layers of particle AGR2-223-RS34 compared to particle AGR2-223-RS06, which has relatively more of those elements’ mass located in the kernel and kernel periphery, suggesting enhanced fission product transport in particle AGR2-223-RS34. This model can be used better understand and test fission product transport in TRISO particles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗