Engineering Papers⌕ Search

Engineering topics

Stein, Manuel

Publications and source records attributed to Stein, Manuel.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Postbuckling response of long thick isotropic plates loaded in compression including higher order transverse shearing effects

Buckling and postbuckling results for aluminum plates loaded in compression are presented. The buckling results were plotted to show the effects of thickness on the stress coefficient. Buckling results are given for various length-to-width ratios. Postbuckling results for plates with transverse shearing flexibility are compared to results from classical theory for various width-to-thickness ratios. The plates are considered to be long with side edges simply supported, with edges free of stress and the plates are subjected to longitudinal compressive displacement. Characteristic curves indicating the average longitudinal direct stress resultant as a function of the applied displacements are calculated based on four different theories: Classical von Karman, first-order shear deformation, higher-order shear deformation, and three-dimensional flexibility. Present results indicate that the three-dimensional flexibility theory gives the lowest and therefore, most accurate results. The higher-order shear deformation theory has fewer unknowns than the three-dimensional flexibility but is not as accurate. The figures presented show that small differences occur in the maximum stress resultants and the transverse displacements calculated when the effects of transverse shear are included.

Stein, Manuel↗
NASA NTRS1990

Postbuckling response of long thick plates loaded in compression including higher order transverse shearing effects

Buckling and postbuckling results are presented for compression-loaded simply-supported aluminum plates and composite plates with a symmetric lay-up of thin + or - 45 deg plies composed of many layers. Buckling results for aluminum plates of finite length are given for various length-to-width ratios. Asymptotes to the curves based on buckling results give N(sub xcr) for plates of infinite length. Postbuckling results for plates with transverse shearing flexibility are compared to results from classical theory for various width-to-thickness ratios. Characteristic curves indicating the average longitudinal direct stress resultant as a function of the applied displacements are calculated based on four different theories: Classical von Karman theory using the Kirchoff assumptions, first-order shear deformation theory, higher-order shear deformation theory, and 3-D flexibility theory. Present results indicate that the 3-D flexibility theory gives the lowest buckling loads. The higher-order shear deformation theory has fewer unknowns than the 3-D flexibility theory but does not take into account through-the-thickness effects. The figures presented show that small differences occur in the average longitudinal direct stress resultants from the four theories that are functions of applied end-shortening displacement.

Stein, Manuel↗
NASA NTRS1990

Postbuckling response of long thick plates loaded in compression including higher order transverse shearing effects

This paper presents buckling and postbuckling results for compression-loaded simply-supported aluminum plates and composite plates with a symmetric lay-up of thin +/-45-deg plies composed of many layers. Buckling results for aluminum plates of finite length are given for various length-to-width ratios. Asymptotes to the curves based on the buckling results give N(XCr) for plates of infinite length. Postbuckling results for plates with transverse shearing flexibility are compared to results from classical theory for various width-to-thickness ratios. Characteristic curves indicating the average longitudinal direct stress resultant as a function of the applied displacements are calculated based on four different theories: classical von Karman theory using the Kirchhoff assumptions, first-order shear deformation theory, higher-order shear deformation theory, and three-dimensional flexibility theory. Present results indicate that the three-dimensional flexibility theory gives the lowest buckling loads. The higher-order shear deformation theory has fewer unknowns than the three-dimensional flexibility theory but does not take into account through-the-thickness effects. The figures presented show that small differences occur in the average longitudinal direct stress resultants from the four theories that are functions of applied end-shortening displacement.

Stein, Manuel↗
NASA NTRS1990

Postbuckling of long thick plates in compression including higher order transverse shearing effects

Aluminum plates of various length/width ratios loaded in compression are examined analytically in terms of buckling and postbuckling for comparison with classical theory. The plates are considered to be subjected to longitudinal compressive displacement with no edge stress and are assumed to be simply supported at the side edges. The average longitudinal direct stresses are computed to plot characteristic curves by means of the following theories: 3D flexibility, higher-order shear deformation, first-order shear deformation, and classical von Karman. The 3D flexibility approach yields the lowest results with more unknowns than the higher-order shear-deformation method. The 3D flexibility approach is considered to be the most accurate, and it is shown that the calculated resultants and displacements tend to vary when consideration is given to the effects of transverse shear.

Stein, Manuel↗
NASA NTRS1989

Vibration of beams and plate strips with three-dimensional flexibility

Studies making use of higher vibration modes and frequencies have indicated a need for a more accurate beam theory. Equations of motion are developed here that give a more accurate representation of the dynamic behavior of a beam than conventional beam theory. Results are obtained using these equations for the natural vibrations of simply-supported aluminum beams of rectangular cross-sections. These results are compared to results from conventional beam theory, and they are examined to identify where various effects are important.

Stein, Manuel↗
NASA NTRS1988

Postbuckling of eccentric open-section stiffened composite panels

A numerical study of the postbuckling behavior of open-section stiffened composite compression panels is presented with emphasis on the effects of an anisotropic attached flange on results, the strain distribution near collapse, and the change of buckle pattern during postbuckling response. Results are obtained for a blade stiffened panel with orthotropic or anisotropic attached flanges from a new verison of STAGS, a general, branched shell, nonlinear computer program. Comparisons between these results indicate the effects of anisotropic flanges on the results. Elastic strain distributions are obtained from STAGS and indications are given about the collapse loads and modes of a particular panel. Change of buckle pattern is studied using STAGS and a special purpose computer program for long plates. Comparisons are made with experimental results.

Stein, Manuel↗
NASA NTRS1987

Effects of transverse shearing flexibility on the postbuckling of plates loaded by inplane shear

This paper presents buckling and postbuckling results for plates loaded by inplane shear. The buckling results have been plotted to show the effects of thickness on the stress coefficient for aluminum plates. Results are given for various length-to-width ratios. Postbuckling results for thin plates with transverse shearing flexibility are compared to results from classical theory. The problems considered are the postbuckling response of plates in shear made of aluminum and of a + or - 45 deg graphite-epoxy laminate. Thus the materials are isotropic and orthotropic, respectively. The plates are considered to be long with side edges simply supported, with various inplane edge conditions, and the plates are subject to a constant shearing displacement along the side edges. Characteristic curves presenting the average shear stress resultant as a function of the applied displacement are given. These curves indicate that change in inplane edge conditions influence plate postbuckling stiffness and that transverse shearing is important in some cases.

Stein, Manuel↗
NASA NTRS1964

The Influence of Prebuckling Deformations and Stresses on the Buckling of Perfect Cylinders

Large-deflection theory is used to compute buckling loads of simply supported initially perfect cylinders under axial compression, external pressure, and combinations of axial compression and internal or external pressure. Important results are obtained by taking into account prebuckling deformations and stresses induced by edge support. For example, the presence of these deformations and stresses can reduce the axial-compression buckling load of an unpressurized perfect cylinder to 50 percent of the classical value.

BUCKLING↗
NASA NTRS1959

Loads and Deformations of Buckled Rectangular Plates

The nonlinear large-deflection equations of von Karman for plates are converted into a set of linear equations by expanding the displacements Into a power series in terms of an arbitrary parameter. The postbuckling behavior of simply supported rectangular plates subjected to longitudinal compression and subject to a uniform temperature rise is investigated in detail by solving the first few of the equations. Experimental data are presented for the compression problem. Comparisons are made for total shortening and local strains and deflections which indicate good agreement between experimental and theoretical results.

Stein, Manuel↗
NASA NTRS1953

Deflection and Stress Analysis of Thin Solid Wings of Arbitrary Plan Form with Particular Reference to Delta Wings

The structural analysis of arbitrary solid cantilever wings by small-deflection thin-plate theory is reduced to the solution of linear ordinary differential equations by the assumption that the chordwise deflections at any spanwise station may be expressed in the form of a power series in which the coefficients are functions of the spanwise coordinate. If the series is limited to the first two and three terms (that is, if linear and parabolic chordwise deflections, respectively, are assumed), the differential equations for the coefficients are solved exactly for uniformly loaded solid delta wings of constant thickness ratio. For cases for which exact solutions to the differential equations cannot be obtained, a numerical procedure is derived. Experimental deflection and stress data for constant-thickness delta-plate specimens of 45 degree and 60 degree sweep are presented and are found to compare favorably with the present theory.

Stein, Manuel↗
NASA NTRS1951

Torsion and transverse bending of cantilever plates

The problem of combined bending and torsion of cantilever plates of variable thickness, such as might be considered for solid thin high-speed airplane or missile wings, is considered in this paper. The deflections of the plate are assumed to vary linearly across the chord; minimization of the potential energy by means of the calculus of variations then leads to two ordinary linear differential equations for the bending deflections and the twist of the plate. Because the cantilever is analyzed as a plate rather than as a beam, the effect of constraint against axial warping in torsion is inherently included. The application of this method to specific problems involving static deflection, vibration, and buckling of cantilever plates is presented. In the static-deflection problems, taper and sweep are considered.

WINGS, SOLID↗