Engineering topics
Publications and source records attributed to Siegel, Peter H..
A novel split-waveguide mount for millimeter and submillimeter wave frequency multipliers and harmonic mixers is presented. It consists of only two pieces, block halves, which are mirror images of each other.
A planar, quasi-optical SIS receiver operating at 230 GHz is described. The receiver consists of a 2 x 5 array of half wave dipole antennas with ten niobium-aluminum oxide-niobium SIS junctions on a quartz dielectric-filled parabola. The 1.4 GHz intermediate frequency is coupled from the mixer via coplanar strip transmission lines and 4:1 balun transformers. The receiver is operated at 4.2 K in a liquid helium immersion cryostat. We report accurate measurements of the performance of single receiver elements. A mixer noise temperature of 89 K DSB, receiver noise temperature of 156 K DSB, and conversion loss of 3 dB into a matched load have been obtained.
Freestanding metallic grids for use as polarizers for electromagnetic radiation at millimeter and submillimeter wavelengths made by simple modification of designs of freestanding square- and nearly-square cell metallic grids, according to proposal. Cross wires provide mechanical support, but distance between cross wires made greater than one wavelength so cross wires have little effect on polarizing characteristics of grid. Possible to fabricate grids commercially for frequencies up to several terahertz.
A planar, quasi-optical SIS receiver operating at 230 GHz is described. The receiver consists of a 2 x 5 array of half wave dipole antennas with ten niobium-aluminum oxide-niobium SIS junctions on a quartz dielectric-filled parabola. The 1.4 GHz intermediate frequency is coupled from the mixer via coplanar strip transmission lines and 4:1 balun transformers. The receiver is operated at 4.2 K in a liquid helium immersion cryostat. We report accurate measurements of the performance of single receiver elements. A mixer noise temperature of 89 K DSB, receiver noise temperature of 156 K DSB, and conversion loss of 3 dB into a matched load have been obtained.
Micromachining-and-electroforming process makes rigid metal meshes with cells ranging in size from 0.002 in. to 0.05 in. square. Series of steps involving cutting, grinding, vapor deposition, and electroforming creates self-supporting, electrically thick mesh. Width of holes typically 1.2 times cutoff wavelength of dominant waveguide mode in hole. To obtain sharp frequency-cutoff characteristic, thickness of mesh made greater than one-half of guide wavelength of mode in hole. Meshes used as high-pass filters (dichroic plates) for submillimeter electromagnetic waves. Process not limited to square silicon wafers. Round wafers also used, with slightly more complication in grinding periphery. Grid in any pattern produced in electroforming mandrel. Any platable metal or alloy used for mesh.
The results of a 600-GHz mixer performance analysis using an improved model for computing the Schottky diode capacitance-voltage (C-V) relationship are presented. The computed C-V data for a realistic submillimeter-waver mixer diode are given as a function of physical temperature and compared to the standard analytic expression based on a solution of Poisson's equation. Both C-V relationships are used to predict the performance of an ideally terminated 600 GHz mixer operating at 300, 140, 80, and 30 K. It is shown that the drift-diffusion model more accurately describes the mixer performance when the physical temperature is reduced below roughly 100 K.
The performance of a microstrip hammerhead filter that has been fabricated on an electrically thin layer of semiinsulating GaAs backed by a fused quartz substrate was measured and compared to results of a three-dimensional finite-difference time-domain (FD-TD) program used to calculate the response of the filter both with and without the GaAs layer. The program, presented by Sheen et al. (1990), discretizes the entire structure and then simulates the propagation of a Gaussian pulse through the filter. The microstrip filter is intended for applications involving ultrathin lifted-off or etched-back GaAs containing both active devices and passive microstrip circuitry backed by a much thicker mechanically rigid low-loss, low-dielectric-constant substrate. The low-pass characteristics of the hammerhead filter with the intermediate GaAs layer are compared with those of the same filter on quartz alone. Both the measured and computed data show a significant shift in cutoff frequency (about 10 percent at the 3 dB points) for a GaAs layer that is 0.007 wavelengths thick at 4 GHz.
The design of a high frequency dichroic plate consisting of an electrically thick self supporting metallic mesh that can be used in a linearly polarized quasi-optical system at high angles of incidence is described. The measured and computed performance of a 2.5-inch aperture mesh is given. This mesh has a 3-dB cutoff frequency of 875 GHz and less than 0.75 dB of transmission loss from 950-1350 GHz at incidence angles of 0, 30, and 45 degrees. The results of a multimode waveguide analysis corroborate the measured data.
A design is presented for a semi-integrated millimeter/submillimeter wavelength receiver/transmitter front end incorporating a planar antenna and a solid-state device in an efficient feed structure which can be matched directly to high f-number optical systems. The feed system combines the simplicity and robustness of a dielectric substrate lens with the high gain of a parabolic reflector in a single structure that is termed a dielectric-filled parabola. The same fundamental unit can be configured as either a heterodyne or direct detection mode receiver, a power transmitter or a frequency multiplier by changing out the solid-state device and/or the integrated antenna. The structure can also be used with a small integrated antenna array in a multibeam or imaging arrangement. Design and fabrication details for the feed system are given. These are followed by beam pattern and impedance measurements taken on a microwave model when dipole, bow-tie, log-periodic, and log-spiral antennas are used as the integrated feed elements.
Planar antennas with receiving and/or transmitting circuits integrated at focal point. Reflectors formed from shaped dielectric material with metallized parabolic surface serve as basis for wide variety of planar, integrated receiver and transmitter circuits operating at millimeter and submillimeter wavelengths. Used over wide range of frequencies and in variety of modes: as receiver or transmitter, in heterodyne or direct-detection mode, with single element, or with array.
Commercial unit modified for antenna-pattern measurements. Addition of automatic range-changing circuit converts Hewlett-Packard 415E standing-wave-ratio (SWR) meter into radio-frequency detector suitable for computer-controlled measurements of radiation patterns of antennas. Modification gives SWR meter effective dynamic range of at least 40 dB. Includes two digital lines communicating one of four range settings to controlling computer and one digital line to inhibit transfer of data when range being changed. Ideal instrument for use in applications involving computer-controlled monitoring of power when large changes in signal level expected.