Engineering Papers⌕ Search

Engineering topics

Shyam, Amit

Publications and source records attributed to Shyam, Amit.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Influence of microstructural heterogeneities on small-scale mechanical properties of an additively manufactured Al-Ce-Ni-Mn alloy

Laser powder bed fusion-based additive manufacturing (AM) is a promising method to fabricate creep-resistant Al-rare earth alloys (Al-Ce-Ni-Mn) with stable microstructures at up to 400°C. However, creep testing of these alloys at high temperatures shows that void coalescence and failure initiation occurs along the melt pool boundaries in the microstructure. Hence it is crucial to understand how the local mechanical behavior of the melt pool boundaries would influence the global properties of the AM produced alloy. In this study, in situ nanoindentation conducted at room temperature and 300°C revealed a reduced hardness at the melt pool boundaries. Similarly, micro-pillar compression showed a slight decline in yield strength at these boundaries, indicating that they are the weak spots in the microstructure. Such multimodal local mechanical property studies are necessary for understanding the influence of melt pool boundaries on the bulk response of fusion-based AM alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase stability in cast and additively manufactured Al-rich Al-Cu-Ce alloys

Additively manufactured (AM) eutectic Al alloy systems have been studied extensively for advantageous thermal stability and mechanical properties due to their refined microstructures. Al-Cu-Ce alloys are one subset of these AM eutectic alloys. Here we studied phase stability in AM Al-Cu-Ce alloys and compared it to that of conventionally cast ones. A new phase, Al 8 Cu 3 Ce, was identified in the microstructures of both AM and cast Al-Cu-Ce alloys. This Al 8 Cu 3 Ce phase was not previously included on experimental or thermodynamically calculated phase diagrams of the Al-Cu-Ce system. Therefore, we performed additional thermodynamic modeling of the system. These models were experimentally validated with cast and subsequently heat-treated Al-Cu-Ce alloys. We found that despite the refined microstructure of the AM alloys, the phases formed were consistent with the cast alloys, suggesting that AM processing did not significantly alter the formation and stability of phases from that in the conventional alloys. In conclusion, this work has resolved inconsistent previous descriptions of the Al-Cu-Ce ternary phase diagram in the Al-rich region and resulted in the addition of the Al 8 Cu 3 Ce as an equilibrium phase above 500 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Using θ' interfaces as templates for planar L1 2 precipitation in AlCuMnZr alloys

Controlled Mn and Zr additions to Al-Cu alloys have allowed for the improved retention of mechanical properties after extended 350°C exposures by stabilizing the main strengthening θ' (Al 2 Cu) phase. Ultimately, θ'/L1 2 (Al 3 Zr) co-precipitate formation stabilizes θ' most effectively; however, Zr diffuses sluggishly and has low solubility in aluminum castings. Increasing the Zr segregation rate would allow for faster and more effective θ'/L1 2 co-precipitation. It is demonstrated that the Zr segregation rate is faster when the Zr matrix content is higher. A much higher Zr matrix content was achieved by rapid cooling during additive manufacturing (AM) that produces θ'/L1 2 co-precipitation faster, which is shown by scanning transmission electron microscopy and atom probe tomography experiments. It was also found that Zr continuously segregates to θ' interfaces up to the most aggressive heat treatment studied such that planar L1 2 precipitates remain after the metastable θ' dissolves. In this manner, we demonstrate that θ' coherent interfaces serve as perfect templates to form stable planar L1 2 precipitates that can provide strength at higher temperatures than traditional θ' strengthened AlCu alloys. This work introduces an alloy design strategy that uses metastable precipitates to quickly nucleate and grow co-precipitates with a desired geometry that contain slow diffusing elements. These ideas can be applied to engineer more heat resistant alloys by taking advantage of high solute matrix contents enabled by rapid cooling during additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Rapid assessment of interfacial stabilization mechanisms of metastable precipitates to accelerate high-temperature Al-alloy development

Precipitate strengthened high-temperature alloys are currently used in safety-critical applications. Understanding precipitate stability and solute segregation mechanisms at high temperatures is key to designing high-strength alloys. Rapid in-situ approaches, therefore, are pivotal in accelerating the alloy design process. Hereby using the test case of a promising high-temperature Al-Cu-Mn-Zr alloy, we demonstrate the value of in-situ atom probe tomography coupled with in-situ transmission electron microscopy to reveal atomic-scale mechanisms that lead to the emergence of non-equilibrium solute segregation. Mn and Zr segregation at strengthening precipitate(θ’)-matrix interface increases the kinetic barrier for phase transformation thus retaining high-temperature strength.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Repurposing the θ (Al 2 Cu) phase to simultaneously increase the strength and ductility of an additively manufactured Al–Cu alloy

The Al–Cu–Mn–Zr (ACMZ) cast family of alloys offers unique properties and value propositions for higher strength, higher temperature lightweight components of future vehicles. Earlier research has demonstrated trade-offs in the selection of the alloy chemistry in which an increase in Cu content from 6 up to 9 wt% improves hot tear resistance but lowers ductility. However, a recent study has demonstrated that higher-Cu (9Cu) ACMZ fabricated with laser powder bed fusion additive manufacturing (AM) results in an increase in both ductility and strength when compared to as-aged microstructure of cast 9Cu alloys. The mechanisms of differing mechanical performance of the cast and AM ACMZ alloys are elucidated in the current paper through the utilization of in situ high energy x-ray diffraction (HEXRD) tensile testing wherein lattice strains of different phases are calculated and correlated to their stresses. The ACMZ alloys consisted of theta (θ) and theta prime (θ') phases (both Al 2 Cu in nominal composition) within an aluminum matrix. The larger micron-size θ phase which decorated the grain boundaries in 9Cu ACMZ cast alloys recorded small lattice strains, while the submicron, homogeneously distributed θ phase in the 9Cu ACMZ AM alloy recorded considerably higher lattice strains. The maximum stress reached in the θ phase for the cast 9Cu alloy was found to be ~280 MPa, which was lower than the AM 9Cu alloy which registered a maximum stress of ~1.4 GPa. These measurements indicate that delayed fracture of the finer intermetallic phases simultaneously improves the ductility and strength of AM 9Cu alloy relative to the cast 9Cu alloy, which exhibits early fracture of the larger intermetallic particles.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Additive manufactured interpenetrating phase composite

A method for preparing metal/metal interpenetrating phase composites is provided. The method includes forming a preform using additive manufacturing. The preform defines a materially continuous three-dimensional open-cell mesh structure. The preform includes a first metal having a melting point. The method further includes pre-heating the preform to a first temperature less than the melting point of the first metal. The method includes infiltrating the preform with a second metal in liquid form. The second metal has a melting point lower than the melting point of the first metal. The method also includes allowing the second metal to cool and form a solid matrix. The solid matrix defines a continuous material network.

Pawlowski, Alex E.↗
DOE OSTI2022

Dislocation-θ' (Al2Cu) interactions during creep deformation of an Al-Cu alloy

While precipitate-dislocation interactions are well-understood for Al-Cu alloys in tension, creep behavior has seen far less study. New, thermally-stabilized Al-Cu alloys have θ' (Al 2 Cu) as strengthening precipitates that remain stable up to 300 °C (~60% of the melting temperature) and higher, where creep becomes essential to the mechanical behavior. This investigation identifies the precipitate-dislocation interactions in such an Al-Cu alloy using in-situ neutron diffraction and scanning transmission electron microscopy. Significant load transfer to the θ' precipitates occurs, which can be attributed to dislocation loops on the interfaces of θ' and the Al matrix. Thus, Orowan looping is identified to be the primary activity for precipitate-dislocation interactions. As Orowan looping and load transfer are associated with significant strain hardening, these results explain the excellent creep resistance seen in this alloy, and provide insights into the design of precipitation strengthened alloys with superior creep performance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of grain-boundary θ-Al 2 Cu precipitates on tensile and compressive creep properties of cast Al–Cu–Mn–Zr alloys

Tensile and compressive creep tests were performed at 300 °C on high-temperature Al–Cu–Mn–Zr (ACMZ) alloys with 6 wt% Cu (6Cu) and 9 wt% Cu (9Cu) to evaluate the effect on creep properties of micron-size θ-Al 2 Cu intergranular precipitates. For compressive creep, the increased volume fraction of θ-precipitates at grain boundaries (from ~0.7% in 6Cu to ~ 6% in 9Cu) does not affect deformation rates across the investigated stress range of 15–110 MPa, consistent with creep being controlled by submicron θ'-Al 2 Cu precipitates within grains, whose size and fractions are the same in both alloys. In contrast, for tensile creep, 9Cu creeps faster than 6Cu at stresses above 20 MPa, and this difference increases with the stress level. Additionally, this discrepancy between tensile and compressive creep behavior is explained by cavitation during tensile creep, which is favored by higher volume fraction and larger size of intergranular θ precipitates in 9Cu. Conversely, larger precipitates impede cavity linkage resulting in improved creep ductility of 9Cu as compared to 6Cu at 300 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructural evolution and strengthening mechanisms in a heat-treated additively manufactured Al–Cu–Mn–Zr alloy

In this report the microstructural and strength evolution of an additively manufactured Al-8.6Cu-0.5Mn-0.9Zr alloy upon aging at 300, 350, and 400 °C is investigated. The strengthening phases of the alloy evolve significantly upon aging, with breakdown and spheroidization of the interconnected θ-Al 2 Cu network, dissolution of metastable θ'-Al 2 Cu precipitates, and precipitation of nanometric L1 2 -Al 3 Zr from a matrix supersaturated in Zr. In the peak-aged states, the alloy displays a favorable combination of strength and ductility, with a room-temperature yield strength of 314–341 MPa and ductility of 11–13%. The measured yield strengths for microstructures with different aging treatments are compared to predictions of yield strengths from grain boundary, solid solution, and particle strengthening contributions. The observed strain hardening behavior is related to fundamental precipitate and dislocation interactions. Comparison between predicted and measured strength values indicates a continued need for strengthening models specifically developed for the heterogeneous microstructures of additively manufactured alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Cavitation-resistant intergranular precipitates enhance creep performance of θ'-strengthened Al-Cu based alloys

Tensile and compressive creep properties of a quaternary Al-Cu-Mn-Zr (ACMZ) alloy and its commercial counterpart (Al-Cu-Mn-Zr with Ni, Co and Sb additions, RR350) are investigated at 300°C. At low stresses up to 30 MPa where diffusional creep dominates, creep resistance is the same in tension and compression and RR350 deforms more slowly than ACMZ, consistent with RR350 alloy's larger linear fraction of intergranular precipitates (Al7Cu2(NiFe) and Al9FeNi for RR350 vs. θ-Al2Cu for ACMZ) and a reduced fraction of precipitate-free zones near grain boundaries. At stresses between 30 and 80 MPa, dislocation creep with a stress exponent n ~ 3 becomes rate-limiting in compression, which is expected to be controlled by θ' precipitates within the grain bulk. By contrast, in tension, enhanced creep rate and higher apparent stress exponents are measured, consistent with cavitation at intergranular precipitates becoming increasingly dominant as the stress increases. In the dislocation creep regime, RR350 alloy is again more creep resistant than ACMZ alloy, which is related to three mechanisms (i) a reduced fraction of softer precipitate-free zones, (ii) more effective load transfer to intergranular precipitates, and (iii) reduced cavitation. A model for cavitation is applied to calculate tensile creep rates from compressive creep rates and the model successfully predicts the improved tensile creep resistance of the RR350 alloy. Overall, the present investigation underscores the importance of intergranular grain boundary precipitates, in addition to strengthening θ' precipitates, in enhancing the creep resistance of Al-Cu alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Aluminum alloy compositions and methods of making and using the same

The present disclosure concerns embodiments of aluminum alloy compositions exhibiting superior microstructural stability and strength at high temperatures. The disclosed aluminum alloy compositions comprise particular combinations of components that contribute the ability of the alloys to exhibit improved microstructural stability and hot tearing resistance as compared to conventional alloys. Also disclosed herein are embodiments of methods of making and using the alloys.

Shyam, Amit↗
DOE OSTI2022

A creep-resistant additively manufactured Al-Ce-Ni-Mn alloy

Existing additively manufactured aluminum alloys exhibit poor creep resistance due to coarsening of their strengthening phases and refined grain structures. In this paper, we report on a novel additively manufactured Al-10.5Ce-3.1Ni-1.2Mn wt.% alloy which displays excellent creep resistance relative to cast high-temperature aluminum alloys at 300–400 °C. In this work, the creep resistance of this alloy is attributed to a high volume fraction (~35%) of submicron intermetallic strengthening phases which are coarsening-resistant for hundreds of hours at 350 °C. The results herein demonstrate that additive manufacturing provides opportunities for development of creep-resistant aluminum alloys that may be used in bulk form in the 250–400 °C temperature range. Pathways for further development of such alloys are identified.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Aluminum alloy compositions and methods of making and using the same

The present disclosure concerns embodiments of aluminum alloy compositions exhibiting microstructural stability and strength at high temperatures. The disclosed aluminum alloy compositions comprise particular combinations of components that contribute the ability of the compositions to exhibit improved microstructural stability and hot tearing resistance as compared to conventional alloys. Also disclosed herein are embodiments of methods of making and using the alloys.

Shyam, Amit↗
DOE OSTI2021

Microstructure and creep properties of cast near-eutectic Al–Ce–Ni alloys

This study investigates the as-cast and aged microstructures, thermal stability, ambient temperature strengthening, and creep resistance of three ternary Al–Ce–Ni alloys (wt%): near-eutectic Al–10Ce–5Ni (with both eutectic and hypoeutectic regions), hypoeutectic Al-7.5Ce-3.75Ni (with numerous primary Al dendrites), and hypereutectic Al-12.5Ce-6.25Ni (with coarse, blocky primary Al3Ni and Al11Ce3 precipitates and some primary Al dendrites). Depending on the alloy composition and local solidification conditions, the following eutectic morphologies are found: (i) coarse Al–Ce eutectic colonies where Al 11 Ce 3 is in the form of “Chinese script”, (ii) intermingled regions of binary Al–Ce and Al–Ni eutectic colonies, with finer Al 3 Ni and Al 11 Ce 3 fibers, (iii) large ternary eutectic colonies, where the binary Al 3 Ni and Al 11 Ce 3 phases are alternating or intertwining within the individual, fine fibers (diameters of ~60–170 nm, depending on solidification rates), and (iv) ternary eutectic zones (between primary Al dendrites), where fine Al 3 Ni and Al 11 Ce 3 build up a 3D-interconnected network. The high volume fraction of intermetallic phases and extremely fine eutectic spacing/fiber diameter both contribute to high ambient strengthening (higher as-cast microhardness than binary Al–Ce or Al–Ni), and also provide enhanced creep resistance at 300 and 350 °C. Additionally, the alloys are coarsening-resistant up to 425 °C for extended periods, with a gradual decrease in microhardness. The alloys aged at 400 °C to 1050 h show fiber fragmentation and coarsening of the resulting particles, with the faster-diffusing Ni driving more rapid coarsening of the Al 3 Ni particles which engulf finer, more stable Al 11 Ce 3 particles. Severe overaging (performed at 590 °C for 24 h) leads to Al 3 Ni and Al 11 Ce 3 spheroids which remain submicron-sized in eutectic colonies, but micron-sized at colony boundary and at Al dendrite-eutectic interface. Creep resistance at 300 °C of overaged Al–10Ce–5Ni remains substantial, consistent with load-transfer based composite strengthening being an important strengthening mechanism in these alloys, making them excellent candidates for replacement of heavier steel or titanium parts operating under stress up to 300 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Heat treatments for high temperature cast aluminum alloys

Disclosed herein are embodiments of an aging heat treatment that can be used to replace conventional aging steps when making alloy embodiments of the present disclosure. Embodiments of the disclosed aging heat treatment reduce cost and complexity in producing aluminum alloy-based components while also promoting and/or improving microstructure stability of the aluminum alloys.

Shyam, Amit↗
DOE OSTI2021

The Role of Interface in Additively Manufactured Interpenetrating Composites

Additively Manufactured Interpenetrating Composites (AMIPCs) are a relatively new metal-metal chain composite in development for use in high energy absorption systems. In this system, reinforcing phase of additively manufactured continuous lattice configurations 316L austenitic stainless-steel is in melt infiltrated with a matrix phase of A356 aluminum-silicon casting alloy. Measurements and observations of this material system have shown that weakly bonded or open/porous interface between the reinforcement and matrix phases exhibits dramatically different mechanical properties of AMIPCs, which is not currently well understood. In this work, Finite Element Models (FEM) are used to model the effects of interfaces between the composite phases. Mechanical tensile tests measurements of various composite volume fractions and varying degrees of casting infiltration are also examined and used to show consistency with the FEM results. The outcome provides insight into material design criteria and performance predictions for new hybrid material systems with exceptional damage tolerance.

Allen, Jason↗
DOE OSTI2021

Elevated temperature ductility dip in an additively manufactured Al-Cu-Ce alloy

The deformation and failure mechanisms of Al-9Cu-6Ce (wt%) based alloys fabricated with laser powder bed fusion were investigated from room temperature to 400°C. The yield and ultimate tensile strengths decreased monotonically with increase in temperature, but the tensile elongation dipped unexpectedly at elevated temperatures and exhibited a minimum at 300°C. The dip in tensile elongation occurred with a concomitant dip in strain-rate sensitivity (SRS) of deformation. The as-fabricated alloy microstructure was heterogeneous, and the heat affected zone (HAZ) underneath the melt pool boundary was prone to strain localization. At 300 °C, the reduced SRS promoted the progression of strain localization in the HAZ leading to failure initiation and the dip in tensile elongation. Furthermore, a higher SRS or strain-hardening rate at other temperatures improved the tensile elongation by slowing the progression of strain localization in the HAZ such that failure initiated by other mechanisms elsewhere in the microstructure. Notably, the tensile elongation was limited by the defect structure only in a narrow temperature range (150 - 200 °C) while at other temperatures it was limited by the inherent microstructural features. This investigation exemplifies unexpected deformation and failure mechanisms possible in heterogeneous microstructures that result from additive manufacturing.

36 MATERIALS SCIENCE↗