Engineering topics

Shih, Tsan-Hsing

Publications and source records attributed to Shih, Tsan-Hsing.

At least 37 records · Page 2

NASA NTRS2000

Bypass Transitional Flow Calculations Using a Navier-Stokes Solver and Two-Equation Models

Bypass transitional flows over a flat plate were simulated using a Navier-Stokes solver and two equation models. A new model for the bypass transition, which occurs in cases with high free stream turbulence intensity (TI), is described. The new transition model is developed by including an intermittency correction function to an existing two-equation turbulence model. The advantages of using Navier-Stokes equations, as opposed to boundary-layer equations, in bypass transition simulations are also illustrated. The results for two test flows over a flat plate with different levels of free stream turbulence intensity are reported. Comparisons with the experimental measurements show that the new model can capture very well both the onset and the length of bypass transition.

Liuo, William W.↗

NASA NTRS1999

A Generalized Wall Function

The asymptotic solutions, described by Tennekes and Lumley (1972), for surface flows in a channel, pipe or boundary layer at large Reynolds numbers are revisited. These solutions can be extended to more complex flows such as the flows with various pressure gradients, zero wall stress and rough surfaces, etc. In computational fluid dynamics (CFD), these solutions can be used as the boundary conditions to bridge the near-wall region of turbulent flows so that there is no need to have the fine grids near the wall unless the near-wall flow structures are required to resolve. These solutions are referred to as the wall functions. Furthermore, a generalized and unified law of the wall which is valid for whole surface layer (including viscous sublayer, buffer layer and inertial sublayer) is analytically constructed. The generalized law of the wall shows that the effect of both adverse and favorable pressure gradients on the surface flow is very significant. Such as unified wall function will be useful not only in deriving analytic expressions for surface flow properties but also bringing a great convenience for CFD methods to place accurate boundary conditions at any location away from the wall. The extended wall functions introduced in this paper can be used for complex flows with acceleration, deceleration, separation, recirculation and rough surfaces.

Shih, Tsan-Hsing↗

NASA NTRS1997

Modeling of Turbulent Swirling Flows

Aircraft engine combustors generally involve turbulent swirling flows in order to enhance fuel-air mixing and flame stabilization. It has long been recognized that eddy viscosity turbulence models are unable to appropriately model swirling flows. Therefore, it has been suggested that, for the modeling of these flows, a second order closure scheme should be considered because of its ability in the modeling of rotational and curvature effects. However, this scheme will require solution of many complicated second moment transport equations (six Reynolds stresses plus other scalar fluxes and variances), which is a difficult task for any CFD implementations. Also, this scheme will require a large amount of computer resources for a general combustor swirling flow. This report is devoted to the development of a cubic Reynolds stress-strain model for turbulent swirling flows, and was inspired by the work of Launder's group at UMIST. Using this type of model, one only needs to solve two turbulence equations, one for the turbulent kinetic energy k and the other for the dissipation rate epsilon. The cubic model developed in this report is based on a general Reynolds stress-strain relationship. Two flows have been chosen for model evaluation. One is a fully developed rotating pipe flow, and the other is a more complex flow with swirl and recirculation.

Shih, Tsan-Hsing↗

NASA NTRS1996

Developments in Computational Modeling of Turbulent Flows

In this paper, we will discuss some recent model developments in two turbulence closure schemes. One is the Reynolds-stress algebraic equation model and the other is the Reynolds-stress transport equation model. Various model constraints required by the rapid distortion theory, the invariant theory and the realizability principle, etc. will be described in the model development.

Shih, Tsan-Hsing↗

NASA NTRS1996

Transonic Turbulent Flow Predictions With Two-Equation Turbulence Models

Solutions of the Favre-averaged Navier-Stokes equations for two well-documented transonic turbulent flows are compared in detail with existing experimental data. While the boundary layer in the first case remains attached, a region of extensive flow separation has been observed in the second case. Two recently developed k-epsilon, two-equation, eddy-viscosity models are used to model the turbulence field. These models satisfy the realizability constraints of the Reynolds stresses. Comparisons with the measurements are made for the wall pressure distribution, the mean streamwise velocity profiles, and turbulent quantities. Reasonably good agreement is obtained with the experimental data.

Liou, William W.↗

NASA NTRS1995

Applications of direct numerical simulation of turbulence in second order closures

This paper discusses two methods of developing models for the rapid pressure-strain correlation term in the Reynolds stress transport equation using direct numerical simulation (DNS) data. One is a perturbation about isotropic turbulence, the other is a perturbation about two-component turbulence -- an extremely anisotropic turbulence. A model based on the latter method is proposed and is found to be very promising when compared with DNS data and other models.

Shih, Tsan-Hsing↗

NASA NTRS1995

Turbulence program for propulsion systems

Program goals at the Center for Modeling of Turbulence and Transition (CMOTT), NASA Lewis Research Center, are (1) to develop reliable turbulence (including bypass transition) and combustion models for complex flows in propulsion systems and (2) to integrate developed models into deliverable CFD tools for propulsion systems in collaboration with industry. This viewgraph presentation covers the following topics: development of turbulence and combustion models; collaboration with industry and technology transfer; isotropic eddy viscosity models; algebraic Reynolds stress models; scalar turbulence models; second order closure models; multiple scale k-epsilon models; and PDF modeling of turbulent reacting flows.

Shih, Tsan-Hsing↗

NASA NTRS1994

A New Reynolds Stress Algebraic Equation Model

A general turbulent constitutive relation is directly applied to propose a new Reynolds stress algebraic equation model. In the development of this model, the constraints based on rapid distortion theory and realizability (i.e. the positivity of the normal Reynolds stresses and the Schwarz' inequality between turbulent velocity correlations) are imposed. Model coefficients are calibrated using well-studied basic flows such as homogeneous shear flow and the surface flow in the inertial sublayer. The performance of this model is then tested in complex turbulent flows including the separated flow over a backward-facing step and the flow in a confined jet. The calculation results are encouraging and point to the success of the present model in modeling turbulent flows with complex geometries.

Shih, Tsan-Hsing↗

NASA NTRS1994

Modeling of Wall-Bounded Complex Flows and Free Shear Flows

Various wall-bounded flows with complex geometries and free shear flows have been studied with a newly developed realizable Reynolds stress algebraic equation model. The model development is based on the invariant theory in continuum mechanics. This theory enables us to formulate a general constitutive relation for the Reynolds stresses. Pope was the first to introduce this kind of constitutive relation to turbulence modeling. In our study, realizability is imposed on the truncated constitutive relation to determine the coefficients so that, unlike the standard k-E eddy viscosity model, the present model will not produce negative normal stresses in any situations of rapid distortion. The calculations based on the present model have shown an encouraging success in modeling complex turbulent flows.

Shih, Tsan-Hsing↗

NASA NTRS1994

A vorticity dynamics based model for the turbulent dissipation: Model development and validation

A new model dissipation rate equation is proposed based on the dynamic equation of the mean-square vorticity fluctuation for large Reynolds number turbulence. The advantage of working with the vorticity fluctuation equation is that the physical meanings of the terms in this equation are more clear than those in the dissipation rate equation. Hence, the model development based on the vorticity fluctuation equation is more straightforward. The resulting form of the model equation is consistent with the spectral energy cascade analysis introduced by Lumley. The proposed model dissipation rate equation is numerically well behaved and can be applied to any level of turbulence modeling. It is applied to a realizable eddy viscosity model. Flows that are examined include: rotating homogeneous shear flows; free shear flows; a channel flow and flat plate boundary layers with and without pressure gradients; and backward facing step separated flows. In most cases, the present model predictions show considerable improvement over the standard kappa-epsilon model.

Shih, Tsan-Hsing↗

NASA NTRS1993

Remarks on turbulent constitutive relations

The paper demonstrates that the concept of turbulent constitutive relations can be used to construct general models for various turbulent correlations. Some of the Generalized Cayley-Hamilton formulas for relating tensor products of higher extension to tensor products of lower extension are introduced. The combination of dimensional analysis and invariant theory can lead to 'turbulent constitutive relations' (or general turbulence models) for, in principle, any turbulent correlations. As examples, the constitutive relations for Reynolds stresses and scalar fluxes are derived. The results are consistent with ones from Renormalization Group (RNG) theory and two-scale Direct-Interaction Approximation (DIA) method, but with a more general form.

Shih, Tsan-Hsing↗

NASA NTRS1993

Critical comparison of second-order closures with direct numerical simulations of homogeneous turbulence

Recently, several models have been proposed for closing the second-moment equations, in which the velocity-pressure gradient tensor and the dissipation rate tensor are two of the most important terms. In the literature, these correlation tensors are usually decomposed into a so-called rapid term and a return-to-isotropy term. Models of these terms have been used in global flow calculations together with other modeled terms. However, their individual behaviors in different flows have not been fully examined because they are unmeasurable in the laboratory. Recently, the development of direct numerical simulation (DNS) of turbulence has given us the possibility to do this kind of study. With direct numerical simulation, we may use the solution to calculate exactly the values of these correlation terms and then directly compare them with the values from their modeled formulations. In this paper, we make direct comparisons of five representative rapid models and eight return-to-isotropy models using the DNS data of 45 homogeneous flows, which were done by Rogers et al. (1986) and Lee and Reynolds (1985). The purpose of these direct comparisons is to explore the performance of these models in different flows and identify the ones that give the best performance. The paper also describes the modeling procedure, model constraints, and the various evaluated models. The detailed results of the direct comparisons are discussed, and a few concluding remarks on turbulence models are given.

Shih, Tsan-Hsing↗

NASA NTRS1993

A multiple-scale model for compressible turbulent flows

A multiple-scale model for compressible turbulent flows is proposed. It is assumed that turbulent eddy shocklets are formed primarily by the 'collisions' of large energetic eddies. The extra straining of the large eddy, due to their interactions with shocklets, enhances the energy cascade to smaller eddies. Model transport equations are developed for the turbulent kinetic energies and the energy transfer rates of the different scale. The turbulent eddy viscosity is determined by the total turbulent kinetic energy and the rate of energy transfer from the large scale to the small scale, which is different from the energy dissipation rate. The model coefficients in the modeled turbulent transport equations depend on the ratio of the turbulent kinetic energy of the large scale to that of the small scale, which renders the model more adaptive to the characteristics of individual flow. The model is tested against compressible free shear layers. The results agree satisfactorily with measurements.

Liou, William W.↗

NASA NTRS1993

A Realizable Reynolds Stress Algebraic Equation Model

The invariance theory in continuum mechanics is applied to analyze Reynolds stresses in high Reynolds number turbulent flows. The analysis leads to a turbulent constitutive relation that relates the Reynolds stresses to the mean velocity gradients in a more general form in which the classical isotropic eddy viscosity model is just the linear approximation of the general form. On the basis of realizability analysis, a set of model coefficients are obtained which are functions of the time scale ratios of the turbulence to the mean strain rate and the mean rotation rate. The coefficients will ensure the positivity of each component of the mean rotation rate. These coefficients will ensure the positivity of each component of the turbulent kinetic energy - realizability that most existing turbulence models fail to satisfy. Separated flows over backward-facing step configurations are taken as applications. The calculations are performed with a conservative finite-volume method. Grid-independent and numerical diffusion-free solutions are obtained by using differencing schemes of second-order accuracy on sufficiently fine grids. The calculated results are compared in detail with the experimental data for both mean and turbulent quantities. The comparison shows that the present proposal significantly improves the predictive capability of K-epsilon based two equation models. In addition, the proposed model is able to simulate rotational homogeneous shear flows with large rotation rates which all conventional eddy viscosity models fail to simulate.

Shih, Tsan-Hsing↗

NASA NTRS1993

Critical assessment of Reynolds stress turbulence models using homogeneous flows

In modeling the rapid part of the pressure correlation term in the Reynolds stress transport equations, extensive use has been made of its exact properties. These, for example, have been employed in obtaining the widely used LRR model. Some recent proposals have dropped one of these properties to obtain new models. We demonstrate, by computing some simple homogeneous flows, that doing so does not lead to any significant improvements over the LRR model and it is not the right direction in improving the performance of existing models.

Shabbir, Aamir↗

NASA NTRS1993

Research activities at the Center for Modeling of Turbulence and Transition

The main research activities at the Center for Modeling of Turbulence and Transition (CMOTT) are described. The research objective of CMOTT is to improve and/or develop turbulence and transition models for propulsion systems. The flows of interest in propulsion systems can be both compressible and incompressible, three dimensional, bounded by complex wall geometries, chemically reacting, and involve 'bypass' transition. The most relevant turbulence and transition models for the above flows are one- and two-equation eddy viscosity models, Reynolds stress algebraic- and transport-equation models, pdf models, and multiple-scale models. All these models are classified as one-point closure schemes since only one-point (in time and space) turbulent correlations, such as second moments (Reynolds stresses and turbulent heat fluxes) and third moments, are involved. In computational fluid dynamics, all turbulent quantities are one-point correlations. Therefore, the study of one-point turbulent closure schemes is the focus of our turbulence research. However, other research, such as the renormalization group theory, the direct interaction approximation method, and numerical simulations are also pursued to support the development of turbulence modeling.

Shih, Tsan-Hsing↗

NASA NTRS1992

Second order closure modeling of turbulent buoyant wall plumes

Non-intrusive measurements of scalar and momentum transport in turbulent wall plumes, using a combined technique of laser Doppler anemometry and laser-induced fluorescence, has shown some interesting features not present in the free jet or plumes. First, buoyancy-generation of turbulence is shown to be important throughout the flow field. Combined with low-Reynolds-number turbulence and near-wall effect, this may raise the anisotropic turbulence structure beyond the prediction of eddy-viscosity models. Second, the transverse scalar fluxes do not correspond only to the mean scalar gradients, as would be expected from gradient-diffusion modeling. Third, higher-order velocity-scalar correlations which describe turbulent transport phenomena could not be predicted using simple turbulence models. A second-order closure simulation of turbulent adiabatic wall plumes, taking into account the recent progress in scalar transport, near-wall effect and buoyancy, is reported in the current study to compare with the non-intrusive measurements. In spite of the small velocity scale of the wall plumes, the results showed that low-Reynolds-number correction is not critically important to predict the adiabatic cases tested and cannot be applied beyond the maximum velocity location. The mean and turbulent velocity profiles are very closely predicted by the second-order closure models. but the scalar field is less satisfactory, with the scalar fluctuation level underpredicted. Strong intermittency of the low-Reynolds-number flow field is suspected of these discrepancies. The trends in second- and third-order velocity-scalar correlations, which describe turbulent transport phenomena, are also predicted in general, with the cross-streamwise correlations better than the streamwise one. Buoyancy terms modeling the pressure-correlation are shown to improve the prediction slightly. The effects of equilibrium time-scale ratio and boundary condition are also discussed.

Zhu, Gang↗

NASA NTRS1992

Critical assessment of Reynolds stress turbulence models using homogeneous flows

In modeling the rapid part of the pressure correlation term in the Reynolds stress transport equations, extensive use has been made of its exact properties which were first suggested by Rotta. These, for example, have been employed in obtaining the widely used Launder, Reece and Rodi (LRR) model. Some recent proposals have dropped one of these properties to obtain new models. We demonstrate, by computing some simple homogeneous flows, that doing so does not lead to any significant improvements over the LRR model and it is not the right direction in improving the performance of existing models. The reason for this, in our opinion, is that violation of one of the exact properties can not bring in any new physics into the model. We compute thirteen homogeneous flows using LRR (with a recalibrated rapid term constant), IP and SSG models. The flows computed include the flow through axisymmetric contraction; axisymmetric expansion; distortion by plane strain; and homogeneous shear flows with and without rotation. Results show that for most general representation for a model linear in the anisotropic tensor, performs either better or as good as the other two models of the same level.

Shabbir, Aamir↗