Engineering topics

Shaw, R. J.

Publications and source records attributed to Shaw, R. J..

At least 37 records · Page 2

NASA NTRS1984

Performance degradation of propeller systems due to rime ice accretion

A theoretical ice accretion model has been established applicable to both aircraft propellers and helicopter rotors to determine the effect of rime ice on the thrust, power, and efficiency as a function of exposure time in a natural icing condition. Comparisons have been made of theoretical performance levels with previously published experimentally determined propeller thrust and efficiency for five natural icing conditions. Agreement between test and theory was acceptable.

Korkan, K. D.↗

NASA NTRS1984

Helicopter rotor performance degradation in natural icing encounter

The analytical model described by Korkan et al. (1982) for predicting the performance degradation of propellers in a natural icing encounter is used to determine the feasibility of predicting helicopter performance degradation in hover during natural icing. The flight condition selected for analysis involves an altitude of 3000 ft and a free-air temperature of 1 F. The values of degradation yielded by the model for rime ice accretion are representative of those experienced in actual flight.

Korkan, K. D.↗

NASA NTRS1984

Heat transfer distributions around nominal ice accretion shapes formed on a cylinder in the NASA Lewis Icing Research Tunnel

Local heat transfer coefficients were obtained on irregular cylindrical shapes which typify the accretion of ice on circular cylinders in cross flow. The shapes were 2, 5, and 15 min accumulations of glaze ice and 15 min accumulation of rime ice. These icing shapes were averaged axially to obtain a nominal shape of constant cross section for the heat transfer tests. Heat transfer coefficients were also measured around the cylinder with no ice accretion. The models were run in a 15.2 x 68.6 cm (6 x 27 in.) wind tunnel at several velocities. The models were also run with a turbulence producing grid which gave about 3.5 percent turbulence. The effect of roughness was also simulated with sand grains glued to the surface. Results are presented as Nusselt number versus angle from the stagnation line for the smooth and rough models for both high and low levels of free stream turbulence. Roughness of the surface in the region prior to flow separation plays a major role in determining the heat transfer distribution. Free stream turbulence does not affect the distribution of heat transfer in this region but raises the level by a nearly uniform amount. For the rime shape, roughness had a larger effect in the near wedge shaped region past the initial separation point.

Van Fossen, G. J.↗

NASA NTRS1984

Progress toward the development of an aircraft icing analysis capability

An overview of the NASA efforts to develop an aircraft icing analysis capability is presented. Discussions are included of the overall and long term objectives of the program as well as current capabilities and limitations of the various computer codes being developed. Descriptions are given of codes being developed to analyze two and three dimensional trajectories of water droplets, airfoil ice accretion, aerodynamic performance degradation of components and complete aircraft configurations, electrothermal deicer, and fluid freezing point depressant deicer. The need for bench mark and verification data to support the code development is also discussed.

Shaw, R. J.↗

NASA NTRS1983

Turbofan blade stresses induced by the flow distortion of a VTOL inlet at high angles of attack

A 51-cm-diameter turbofan with a tilt-nacelle VTOL inlet was tested in the Lewis Research Center's 9- by 15-Ft Low Speed Wind Tunnel at velocities up to 72 m/s and angles of attack up to 120 deg. Fan-blade vibratory stress levels were investigated over a full aircraft operating range. These stresses were due to inlet air flow distortion resulting from (1) internal flow separation in the inlet, and (2) ingestion of the exterior nacelle wake. Stress levels are presented, along with an estimated safe operating envelope, based on infinite blade fatigue life.

Williams, R. C.↗

NASA NTRS1983

Influence of multidroplet size distribution on icing collection efficiency

Calculation of collection efficiencies of two-dimensional airfoils for a monodispersed droplet icing cloud and a multidispersed droplet is carried out. Comparison is made with the experimental results reported in the NACA Technical Note series. The results of the study show considerably improved agreement with experiment when multidroplet size distributions are employed. The study then investigates the effect of collection efficiency on airborne particle droplet size sampling instruments. The biased effect introduced due to sampling from different collection volumes is predicted.

Chang, H.-P.↗

NASA NTRS1983

NASA Lewis Research Center's program on icing research

NASA is again actively involved in aircraft icing research. This paper briefly describes the new research activity in ice protection systems, icing instrumentation, experimental methods, analytical modeling for the above, and in-flight research. The renewed interest in aircraft icing has come about mainly because of the new need for all-weather helicopters and general aviation aircraft. Because of increased fuel costs, tomorrow's commercial transports also will require new types of ice protection systems compatible with the more efficient high by-pass and turboprop engines. And all types of aircraft require better estimates of the aeropenalties caused by ice on unprotected surfaces.

Reinmann, J. J.↗

NASA NTRS1982

An Experimental Study of Airfoil Icing Characteristics

A full scale general aviation wing with a NACA 63 sub 2 A415 airfoil section was tested to determine icing characteristics for representative rime and glaze icing conditions. Measurements were made of ice accretion shapes and resultant wing section drag coefficient levels. It was found that the NACA 63 sub 2 A415 wing section was less sensitive to rime and glaze icing encounters for climb conditions.

Shaw, R. J.↗

NASA NTRS1982

Aircraft icing research at NASA

Research activity is described for: ice protection systems, icing instrumentation, experimental methods, analytical modeling for the above, and in flight research. The renewed interest in aircraft icing has come about because of the new need for All-Weather Helicopters and General Aviation aircraft. Because of increased fuel costs, tomorrow's Commercial Transport aircraft will also require new types of ice protection systems and better estimates of the aeropenalties caused by ice on unprotected surfaces. The physics of aircraft icing is very similar to the icing that occurs on ground structures and structures at sea; all involve droplets that freeze on the surfaces because of the cold air. Therefore all icing research groups will benefit greatly by sharing their research information.

Reinmann, J. J.↗

NASA NTRS1982

An experimental study of airfoil icing characteristics

The present investigation is concerned with the icing characteristics of a general aviation wing section, taking into account selected results from icing wind tunnel tests of the wing section. Drag coefficient increases of about 130 percent were measured for a 20 minute glaze icing encounter and cruise aerodynamic conditions. The drag increased by about 40 percent for a 15 minute rime icing encounter and the same aerodynamic conditions. The considered wing section was found to be less sensitive to rime and glaze ice accretions occurring for the climb aerodynamic conditions. The observed aft frost layer growths contributed significantly to the measured increase in section drag coefficient level. Comparisons of measured increases in section drag coefficient due to the primary ice accretion with predictions of NACA drag correlation indicated agreement was as good as that for the original data upon which the correlation was based.

Shaw, R. J.↗

NASA NTRS1982

Performance degradation of propeller/rotor systems due to rime ice accretion

A theoretical model has been established which is applicable to both propeller and helicopter systems that determines the effect of rime ice accretion on the thrust coefficient, power coefficient, and efficiency as a function of time in a natural icing condition. Theoretical comparisons have been made with experimentally determined decrease in propeller thrust coefficient and efficiency for five natural icing conditions with good agreement. The present analytical model is also applicable to the helicopter case, where the method predicts radial and azimuthal rotor blade ice shapes in addition to torque rise as a function of time in a natural icing condition.

Korkan, K. D.↗

NASA NTRS1982

NASA Lewis Research Center's Program on Icing Research

The helicopter and general aviation, light transport, and commercial transport aircraft share common icing requirements: highly effective, lightweight, low power consuming deicing systems, and detailed knowledge of the aeropenalties due to ice on aircraft surfaces. To meet current and future needs, NASA has a broadbased icing research program which covers both research and engineering applications, and is well coordinated with the FAA, DOD, universities, industry, and some foreign governments. Research activity in ice protection systems, icing instrumentation, experimental methods, analytical modeling, and in-flight research are described.

Reinmann, J. J.↗

NASA NTRS1981

An analytical approach to airfoil icing

An analytical procedure has been developed to predict rime ice growth on unprotected airfoil sections and to evaluate the aerodynamic performance. A time stepping method is used in which: (1) water droplet trajectories are calculated, (2) a rime ice shape determined, (3) the flowfield around the iced airfoil is recalculated, and (4) the build-up process iterated upon until the desired icing time is reached. The performance of the iced airfoil shapes are then determined from existing analytic methods. Rime ice shapes determined in the NASA Lewis Icing Research Tunnel on a modified NACA 64 series airfoil agree well with the shapes predicted by the analytical method. Measured and predicted increases in drag due to the rime ice also agree favorably. A simplified scaling analysis is also presented and verified which provides the duplication of full scale results of rime ice accretions in small scale model tests.

Bragg, M. B.↗

NASA NTRS1979

An Experimental Investigation of Forced Mixing of a Turbulent Boundary Layer in an Annular Diffuser

The forced mixing process of a turbulent boundary layer in an axisymmetric annular diffuser using conventional wing-like vortex generators was studied. Flow field measurements were made at four axial locations downstream of the vortex generators. At each axial location, a total of 25 equally spaced profiles were measured behind three consecutive vortex generators which formed two pairs of vortex generators. Hot film anemometry probes measured the boundary layer turbulence structure at the same locations where pressure measurements were made. Both single and cross film probes were used. The diffuser turbulence data was teken only for a nominal inlet Mach number of 0.3. Three vortex generator configurations were tested. The differences between configurations involved changes in size and relative vortex generator positions. All three vortex generator configurations tested provided increases in diffuser performance. Distinct differences in the boundary layer integral properties and skin friction levels were noted between configurations. The axial turbulence intensity and Reynolds stress profiles measured displayed similarities in trends but differences in levels for the three configurations.

Shaw, R. J.↗

NASA NTRS1978

VSTOL tilt nacelle aerodynamics and its relation to fan blade stresses

A scale model of a VSTOL tilt nacelle with a 0.508 m single stage fan was tested in a low speed wind tunnel to ascertain inlet aerodynamic and fan aeromechanical performance over the low speed flight envelope. Fan blade stress maxima occurred at discrete rotational speeds corresponding to integral engine order vibrations of the first flatwise bending mode. Increased fan blade stress levels coincided with internal boundary layer separation but became severe only when the separation location had progressed to the entry lip region of the inlet.

Shaw, R. J.↗

NASA NTRS1978

VSTOL tilt nacelle aerodynamics and its relation to fan blade stresses

A scale model of a VSTOL tilt nacelle with a 0.508 m single stage fan was tested in the NASA Lewis 9x15 Low Speed Wind Tunnel to ascertain inlet aerodynamic and fan aeromechanical performance over the low speed flight envelope. Fan blade stress maxima occurred at discrete rotational speeds corresponding to integral engine order vibrations of the first flatwise bending mode. Increased fan blade stress levels coincided with internal boundary layer separation occurring but became severe only when the separation location had progressed to the entry lip region of the inlet. The inlet/fan system could operate within the low speed flight envelope without incurring fan blade stress limits although boundary layer separation did occur for certain operating conditions.

Shaw, R. J.↗

NASA NTRS1977

Operating characteristics of an inlet model tested with a 0.5m powered fan at high angles of attack

An inlet model designed for high angle of attack capability, coupled to a .508 m tip diameter turbofan simulator, was tested in the NASA-Lewis Research Center's 9-by 15-ft low speed wind tunnel. The test variables were: tunnel velocity, 0 to 75 m/s; inlet angle of attack, 0 to 120 deg; and fan face corrected airflow per unit area, 75 to 200 kg/s sqm. The inlet flow separation boundaries, the fan face total pressure recovery and distortion characteristics, and the fan blade vibratory stresses were determined. The recovery, distortion, and stress levels showed no abrupt changes at the onset of separation, but became gradually more unfavorable as the size and intensity of the separation increased as induced by increasingly severe operating conditions. Performance characteristics for a large scale model of the inlet were estimated from these test results.

Koncsek, J. L.↗

NASA NTRS1976

Boundary layer bleed system study for a full-scale, mixed-compression inlet with 45 percent internal contraction

The results of an experimental bleed development study for a full-scale, Mach 2.5, axisymmetric, mixed-compression inlet were presented. The inlet was designed to satisfy the airflow requirements of the TF30-P-3 turbofan engine. Capabilities for porous bleed on the cowl surface and ram-scoop/flush-slot bleed on the centerbody were provided. A configuration with no bleed on the cowl achieved a minimum stable, diffuser exit, total pressure recovery of 0.894 with a centerbody-bleed mass flow ratio of 0.02. Configurations with cowl bleed had minimum stable recoveries as high as 0.900 but suffered range decrement penalties from the increased bleed mass flow removal. Limited inlet stability and unstart angle-of-attack data are presented.

Shaw, R. J.↗