Engineering topics
Publications and source records attributed to Seraji, H..
This paper presents an new strategy for autonomous navigation of planetary rovers using the fuzzy logic framework and novel on-board measure of terrain traversability.
This paper describes the approach followed in the design of a service robot for health care applications. This paper describes the architecture of the subsystem, the features of the manipulator arm, and the operator interface.
Within NASA's recent thrust for industrial collaboration, JPL has recently established two technology cooperation agreements in the robotics area: one on virtual reality calibration with Deneb Robotics, Inc., and the other on redundant manipulator control with Robotics Research Corporation (RRC). These technology transfer tasks will enable both Deneb and RRC to commercialize an upgraded version of their products that will greatly benefit both space and terrestrial telerobotic applications.
This paper presents a simple and robust kinematic control scheme for the JPL serpentine robot system. The proposed strategy is developed using the dampened-least-squares/configuration control methodology, and permits the considerable dexterity of the JPL serpentine robot to be effectively utilized for maneuvering in the congested and uncertain workspaces often encountered in inspection tasks. Computer simulation results are given for the 20 degree-of-freedom (DOF) manipulator system obtained by mounting the twelve DOF serpentine robot at the end-effector of an eight DOF Robotics Research arm/lathe-bed system. These simulations demonstrate that the proposed approach provides an effective method of controlling this complex system.
The implementation, experimentation, and application of contact control schemes for a 7-DOF Robotics Research arm is presented. Three types of control schemes are presented: compliance cntrol, force control, and dual-mode control. This presentation is concluded with the application of the proposed schemes to perform a contact-based eddy-current inspection task.
This paper addresses the problem of base placement for mobile robots, and proposes a simple off-line solution to determine the appropriate base locations from which the robot can reach a target point.
This paper addresses the problem of controlling a manipulator in compliant motion while in contact with an environment having an unknown stiffness. Two classes of solutions are discussed: adaptive admittance control and adaptive compliance control. In both admittance and compliance control schemes, compensator adaptation is used to ensure a stable and uniform system performance.
This paper presents a simple on-line approach for motion control of mobile robots made up of a manipulator arm mounted on a mobile base. The proposed approach is equally applicable to nonholonomic mobile robots, such as rover-mounted manipulators and to holonomic mobile robots such as tracked robots or compound manipulators. The computational efficiency of the proposed control scheme makes it particularly suitable for real-time implementation.
This paper reports on an on-going research and development effort in remote surface inspection of space platforms such as the Space Station Freedom (SSF). It describes the space environment and identifies the types of damage for which to search. This paper provides an overview of the Remote Surface Inspection System that was developed to conduct proof-of-concept demonstrations and to perform experiments in a laboratory environment. Specifically, the paper describes three technology areas: (1) manipulator control for sensor placement; (2) automated non-contact inspection to detect and classify flaws; and (3) an operator interface to command the system interactively and receive raw or processed sensor data. Initial findings for the automated and human visual inspection tests are reported.
This paper reports on an on-going research and development effort in remote surface inspection of space platforms such as the Space Station Freedom. It describes the space environment and identifies the types of damage that these platforms need to be inspected for. It provides an overview of the Remote Surface Inspection System that has been developed to conduct proof-of-concept demonstrations and to perform experiments in a laboratory environment. Initial findings for the automated and human visual inspection tests are reported.
The article puts forward a simple scheme for multivariable control of robot manipulators to achieve trajectory tracking. The scheme is composed of an inner loop stabilizing controller and an outer loop tracking controller. The inner loop utilizes a multivariable PD controller to stabilize the robot by placing the poles of the linearized robot model at some desired locations. The outer loop employs a multivariable PID controller to achieve input-output decoupling and trajectory tracking. The gains of the PD and PID controllers are related directly to the linearized robot model by simple closed-form expressions. The controller gains are updated on-line to cope with variations in the robot model during gross motion and for payload change. Alternatively, the use of high gain controllers for gross motion and payload change is discussed. Computer simulation results are given for illustration.
An adaptive scheme for controlling the end-effector impedance of robot manipulators is presented. The proposed control system consists of three subsystems: a simple filter which characterizes the desired dynamic relationship between the end-effector position error and the end-effector/environment contact force, an adaptive controller which produces the Cartesian-space control input required to provide this desired dynamic relationship, and an algorithm for mapping the Cartesian-space control input to a physically realizable joint-space control torque. The controller does not require knowledge of either the structure or the parameter values of the robot dynamics, and it is implemented without calculation of the robot inverse kinematic transformation. As a result, the scheme represents a very general and computationally efficient approach to controlling the impedance of both nonredundant and redundant manipulators. Furthermore, the method can be applied directly to trajectory tracking in free-space motion by removing the impedance filter.
This article presents a singularity-robust task-prioritized reformulation of the configuration control scheme for redundant robot manipulators. This reformulation suppresses large joint velocities near singularities, at the expense of small task trajectory errors. This is achieved by optimally reducing the joint velocities to induce minimal errors in the task performance by modifying the task trajectories. Furthermore, the same framework provides a means for assignment of priorities between the basic task of end-effector motion and the user-defined additional task for utilizing redundancy. This allows automatic relaxation of the additional task constraints in favor of the desired end-effector motion, when both cannot be achieved exactly. The improved configuration control scheme is illustrated for a variety of additional tasks, and extensive simulation results are presented.
The implementation and experimental validation of a direct adaptive control scheme on a PUMA 560 industrial robot is discussed. The design theory for direct adaptive control of manipulators is outlined and the test facility and software are described. Results are presented from the experiments on the simultaneous control of all of the six joint angles and control of the end-effector position and orientation of the robot. Also, the possible applications of the direct adaptive control scheme are considered.
An adaptive algorithm for solving the inverse kinematics problem for robot manipulators is presented. The algorithm is derived using model reference adaptive control (MRAC) theory and is computationally efficient for online applications. The scheme requires no a priori knowledge of the kinematics of the robot if Cartesian end-effector sensing is available, and it requires knowledge of only the forward kinematics if joint position sensing is used. Computer simulation results are given for the redundant seven-DOF robotics research arm, demonstrating that the proposed algorithm yields accurate joint angle trajectories for a given end-effector position/orientation trajectory.
A kinematic analysis of anthropomorphic seven-degree-of-freedom serial link spatial manipulators with revolute joints is presented. To uniquely determine joint angles for a given end-effector position and orientation, the redundancy is parameterized by a scalar variable which corresponds to the angle between the arm plane and a reference plane. The forward kinematic mappings from joint-space to end-effector coordinates and arm angle and the augmented Jacobian matrix which gives end-effector and arm angle rates as functions of joint rates are given. Conditions under which the augmented Jacobian becomes singular are given and are shown to correspond to the arm being either at a kinematically singular configuration or at a nonsingular configuration for which the arm angle ceases to parameterize the redundancy.
A scheme for controlling the mechanical impedance of the end-effector of a kinematically redundant manipulator is presented. The proposed control system consists of two subsystems: an adaptive impedance controller which generates the Cartesian-space control input F (is a member of Rm) required to provide the desired end-effector impedance characteristics, and an algorithm that maps this control input to the joint torque T (is a member of Rn). The F to T map is constructed so that the robot redundancy is utilized to improve either the kinematic or dynamic performance of the robot. The impedance controller does not require knowledge of the complex robot dynamic model or parameter values for the robot, the payload, or the environment, and is implemented without calculation of the robot inverse kinematic transformation. As a result, the scheme is very general and is computationally efficient for on-line implementation.
The authors present a singularity-robust task-prioritized reformulation of the configuration control for redundant robot manipulators. This reformation suppresses large joint velocities to induce minimal errors in the task performance by modifying the task trajectories. Furthermore, the same framework provides a means for assignment of priorities between the basic task of end-effector motion and the user-defined additional task for utilizing redundancy. This allows automatic relaxation of the additional task constraints in favor of the desired end-effector motion when both cannot be achieved exactly.