Engineering Papers⌕ Search

Engineering topics

Seka, W

Publications and source records attributed to Seka, W.

32 records · Page 2

Investigation Into the Optimum Beam Shape and Fluence for Selective Ablation of Dental Calculus at lambda = 400 nm

A frequency-doubled Ti:sapphire laser is shown to selectively ablate dental calculus. The optimal transverse shape of the laser beam, including its variability under water-cooling, is determined for selective ablation of dental calculus. Intensity profiles under various water-cooling conditions were optically observed. The 400-nm laser was coupled into a multimode optical fiber using an f = 2.5-cm lens and light-shaping diffuser. Water-cooling was supplied coaxially around the fiber. Five human tooth samples (four with calculus and one pristine) were irradiated perpendicular to the tooth surface while the tooth was moved back and forth at 0.3 mm/second, varying between 20 and 180 iterations. The teeth were imaged before and after irradiation using light microscopy with a flashing blue light-emitting diode (LED). An environmental scanning electron microscope imaged each tooth after irradiation. High-order super-Gaussian intensity profiles are observed at the output of a fiber coiled around a 4-in. diameter drum. Super-Gaussian beams have a morehomogenous fluence distribution than Gaussian beams and have a higher energy efficiency for selective ablation. Coaxial water-cooling does not noticeably distort the intensity distribution within 1 mm from the optical fiber. In contrast, lasers focused to a Gaussian cross section (<=50-mm diameter) without fiber propagation and cooled by a water spray are heavily distorted and may lead to variable ablation. Calculus is preferentially ablated at high fluences (>= 2 J/cm^2); below this fluence, stalling occurs because of photo-bleaching of the calculus. Healthy dental hard tissue is not removed at fluences <=3 J/cm^2. Supplying laser light to a tooth using an optical fiber with coaxial water-cooling is determined to be the most appropriate method when selectively removing calculus with a frequency-doubled Ti:sapphire laser. Fluences over 2 J/cm^2 are required to remove calculus efficiently since photo-bleaching stalls calculus removal below that value.

calculus removal↗

Suprathermal Electrons Generated by the Two-Plasmon-Decay Instability in Gas-Filled Hohlraums

For the first time a burst of suprathermal electrons is observed from the exploding laser-entrance-hole window of gas-filled Hohlraums driven with 13.5 kJ of 351 nm laser light. The two-plasmon-decay instability appears to produce up to 20 J of hot electrons with T_hot ~ 75 keV at early times and has a sharp laser-intensity threshold between 0.3 and 0.5 x 10^15 W/cm^2. The observed threshold can be exploited to mitigate preheat by window hot electrons in ignition Hohlraums for the National Ignition Facility and achieve high-density, high-pressure conditions in indirect drive implosions.

Regan, S P↗

Advanced-Ignition-Concept Exploration on OMEGA

Advanced ignition concepts, such as fast ignition and shock ignition, are being investigated at the Omega Laser Facility. Integrated fast-ignition experiments with room-temperature re-entrant cone targets have begun, using 18 kJ of 351 nm drive energy to implode empty 40μm thick CD shells, followed by 1.0 kJ of 1053 nm wavelength, short-pulse energy. Short pulses of 10 ps width have irradiated the inside of a hollow gold re-entrant cone at the time of peak compression. A threefold increase in the time-integrated, 2 to 7 keV x-ray emission was observed with x-ray pinhole cameras, indicating that energy is coupled from the short-pulse laser into the core by fast electrons. In shock-ignition experiments, spherical plastic-shell targets were compressed to high areal densities on a low adiabat, and a strong shock wave was sent into the converging, compressed capsule. In one experiment, 60 beams were used with an intensity spike at the end of the laser pulse, and the implosion performance was studied through neutron-yield and areal-density measurements. In a second experiment, the 60 OMEGA beams were split into a 40+20 configuration, with 40 low-intensity beams used for fuel assembly and 20 delayed beams with a short, high-intensity pulse shape (up to 1×1016 Wcm^-2) for shock generation.

Theobald, W↗

Advanced-Ignition-Concept Exploration on OMEGA

Advanced ignition concepts, such as fast ignition and shock ignition, are being investigated at the Omega Laser Facility. Integrated fast-ignition experiments with room-temperature re-entrant cone targets have begun, using 18 kJ of 351 nm drive energy to implode empty 40μm thick CD shells, followed by 1.0 kJ of 1053 nm wavelength, short-pulse energy. Short pulses of 10 ps width have irradiated the inside of a hollow gold re-entrant cone at the time of peak compression. A threefold increase in the time-integrated, 2 to 7 keV x-ray emission was observed with x-ray pinhole cameras, indicating that energy is coupled from the short-pulse laser into the core by fast electrons. In shock-ignition experiments, spherical plastic-shell targets were compressed to high areal densities on a low adiabat, and a strong shock wave was sent into the converging, compressed capsule. In one experiment, 60 beams were used with an intensity spike at the end of the laser pulse, and the implosion performance was studied through neutron-yield and areal-density measurements. In a second experiment, the 60 OMEGA beams were split into a 40+20 configuration, with 40 low-intensity beams used for fuel assembly and 20 delayed beams with a short, high-intensity pulse shape (up to 1×10 16 Wcm -2 ) for shock generation.

42 ENGINEERING↗

Laser Ablation of Dental Calculus Around 400 nm Using a Ti:Sapphire Laser

A Nd:YAG laser-pumped, frequency-doubled Ti:sapphire laser is used for selective ablation of calculus. The laser provides ≤25 mJ at 400 nm (60-ns pulse width, 10-Hz repetition rate). The laser is coupled into an optical multimode fiber coiled around a 4-in.-diam drum to generate a top-hat output intensity profile. With coaxial water cooling, this is ideal for efficient, selective calculus removal. This is in stark contrast with tightly focused Gaussian beams that are energetically inefficient and lead to irreproducible results. Calculus is well ablated at high fluences ≥2 J/cm^2; stalling occurs below this fluence because of photobleaching. Healthy hard tissue is not removed at fluences ≤3 J/cm^2.

calculus removal↗

A pulsed-laser calibration system for the laser backscatter diagnostics at the Omega laser

A calibration system has been developed that allows a direct determination of the sensitivity of the laser backscatter diagnostics at the Omega laser. A motorized mirror at the target location redirects individual pulses of a mJ-class laser onto the diagnostic to allow the in-situ measurement of the local point response of the backscatter diagnostics. Featuring dual wavelength capability at the 2nd and 3rd harmonic of the Nd:YAG laser, both spectral channels of the backscatter diagnostics can be directly calibrated. In addition, channel cross-talk and polarization sensitivity can be determined. The calibration system has been employed repeatedly over the last two years and has enabled precise backscatter measurements of both stimulated Brillouin scattering and stimulated Raman scattering in gas-filled hohlraum targets that emulate conditions relevant to those in inertial confinement fusion targets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Control of 2{omega} (527 nm) stimulated Raman scattering in a steep density gradient plasma

Experiments show that application of laser smoothing schemes including smoothing by spectral dispersion and polarization smoothing effectively suppresses stimulated Raman scattering from a 2{omega} (527 nm) laser beam in a low average-gain plasma with a steep density gradient. Full-wave simulations reproduce the observed trends in the data and show that the scattering reduction is an indirect result of suppressing active filamentation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Two-Plasmon-Decay Instabilty in Direct-Drive Inertial Confinement Fusion Experiments

The two-plasmon-decay (TPD) instability in direct-drive irradiation OMEGA [J. M. Soures, R. L. McCrory, C. P. Verdon, et al., Phys. Plasmas 3, 2108 (1996)] experiments is seen in the half-integer harmonic emission. Experimental time-resolved w/2 and 3w/2 spectra indicate that the linear theory for the absolute TPD instability reasonably predicts TPD thresholds. The plasma wave spectra do not, however, agree at all with the predictions of the linear theory. This is most likely a consequence of the nonlinear evolution of this instability once it is above threshold. This is demonstrated with spectral data obtained from spherical implosion experiments as well as planar target experiments. In the latter, Thomson scattering shows the importance of the Landau cutoff. For the TPD instability, the Landau cutoff is found to be respected in all spherical and planar target experiments. In addition, the maximum plasma wave amplitudes appear to occur near the Landau cutoff.

Seka, W↗

Cryogneic-Target Performance and Implosion Physics Studies on OMEGA

Recent progress in direct-drive cryogenic implosions on the OMEGA Laser Facility [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] is reviewed. Ignition-relevant areal densities of ~200 mg/cm^2 in cryogenic D2 implosions with peak laser-drive intensities of ~5 x 10^14 W/cm^2 were previously reported [T. C. Sangster et al., Phys. Rev. Lett. 100, 185006 (2008)]. The laser intensity is increased to ~10^15 W/cm^2 to demonstrate ignition-relevant implosion velocities of 3–4 x 10^7 cm/ s, providing an understanding of the relevant target physics. Planar-target acceleration experiments show the importance of the nonlocal electron-thermal-transport effects for modeling the laser drive. Nonlocal and hot-electron preheat is observed to stabilize the Rayleigh–Taylor growth at a peak drive intensity of ~10^15 W/cm^2. The shell preheat caused by hot electrons generated by two-plasmon-decay instability was reduced by using Si-doped ablators. The measured compressibility of planar plastic targets driven with high-compression shaped pulses agrees well with one-dimensional simulations at these intensities. Shock mistiming has contributed to compression degradation of recent cryogenic implosions driven with continuous pulses. Multiple-picket (shock-wave) target designs make it possible for a more robust tuning of the shock-wave arrival times. Cryogenic implosions driven with double-picket pulses demonstrate somewhat improved compression performance at a peak drive intensity of ~10^15 W/cm^2.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effectiveness of Silicon as a Laser Sshinethrough Barrier for 351-nm Light

Many laser beams directly illuminate a spherical target in direct-drive inertial confinement fusion experiments, ionizing the outer surface and surrounding the target with a plasma containing an opaque critical surface. In the earliest stages of irradiation, before the plasma forms a critical-density surface, laser light can penetrate into the target. This “shinethrough” light can be sufficiently intense to undergo filamentation and damage the inside of the target, thereby seeding hydrodynamic instabilities. Laser shinethrough can be blocked by a thin coating of opaque material, such as, aluminum (Al). For cryogenic direct-drive targets, the shinethrough barrier material must also be compatible with cryogenic target fabrication procedures, which rules out Al layers since they would interfere with permeation filling and optical characterization of cryogenic targets. Silicon (Si) has been found to be a promising candidate for a direct-drive cryogenic target shinethrough barrier material. Several cryogenic targets have been coated with Si, successfully permeation filled with either deuterium (D2) or deuterium-tritium (DT), and subsequently layered and optically characterized. Various thicknesses of Si coatings have been applied to planar targets and tested under relevant irradiation conditions. Experiments have shown that 200 Å of Si is sufficient to protect targets from laser shinethrough.

Edgell, D H↗

Hohlraum Energetics and Implosion Symmetry with Elliptical Phase Plates Using a Multi-Cone Beam Geometry on OMEGA

Hohlraum energetics and implosion-symmetry experiments were conducted on the OMEGA Laser System using laser beams arranged in three cones and smoothed with elliptical phase plates. The peak radiation temperature (Tr) increased by 17 eV, with phase plates for gas-filled halfraums irradiated with 20 beams using a ~7-kJ shaped laser pulse (PS26), corresponding to a 44% increase in the peak x-ray flux. The improved coupling correlates with reduced, cone-dependent losses from stimulated Raman scattering (SRS) and stimulated Brillouin scattering (SBS). Phase plates reduce SRS and SBS by controlling the on-target laser-intensity envelope and the speckle modal power spectrum. An implosion symmetry scan was performed by varying the length and beam pointing of vacuum and gas-filled, thin-walled (3 um) Au hohlraums irradiated with 40 beams using a ~14-kJ PS26. Gated-x-ray (hv > 3 keV) images taken along radial and axial views of the self-emission from Ar-doped, D2-filled, plastic-shell implosions quantified the indirect-drive-implosion symmetry. A shift in symmetry was observed between vacuum and gas-filled hohlraums having identical beam pointing. The ratio of x-ray drive at the poles of the capsule relative to the waist increased for the gas-filled hohlraum. Levels of hard-x-ray production (hv > 20 keV) and SRS were reduced with trace amounts of high-Z dopants (i.e., Ne, Kr) in the hohlraum plasma, while the peak Tr increased ~5 eV.

Regan, S P↗

Cryogenic Target-Implosion Experiments on OMEGA

The University of Rochester’s Laboratory for Laser Energetics has been imploding thick cryogenic targets for six years. Improvements in the Cryogenic Target Handling System and the ability to accurately design laser pulse shapes that properly time shocks and minimize electron preheat, produced high fuel areal densities in deuterium cryogenic targets (202+/-7 mg/cm^2). The areal density was inferred from the energy loss of secondary protons in the fuel (D2) shell. Targets were driven on a low final adiabat (alpha = 2) employing techniques to radially grade the adiabat (the highest adiabat at the ablation surface). The ice layer meets the target-design toughness specification for DT ice of 1-um rms (all modes), while D2 ice layers average 3.0-um-rms roughness. The implosion experiments and the improvements in the quality and understanding of cryogenic targets are presented.

Harding, D R↗

The Role of Fast-Electron Preheating in Low-Adiabat Cryogenic Implosions on OMEGA

The compression in direct-drive, low-adiabat spherical implosions was studied using cryogenic D2 targets on the 60-beam, 351-nm OMEGA laser in the range of laser intensities from ~3 x 10^14 to ~1.5 x 10^15 W/cm^2. The neutron-burn–averaged areal densities decreased as the laser intensity increased. This decrease in areal density is highly correlated with the increased hard-x-ray signals, caused by hot electrons generated by the two-plasmon-decay instability. The areal-density reduction up to ~2, observed in the experiments, requires a preheat energy of ~60 J (~0.3% of total laser energy), which is consistent with the estimated preheat levels inferred from the hard-x-ray signal levels. Mitigating the generation of fast-electrons results in high areal densities which are close to the 1D predictions.

Shvarts, D↗

Modeling High-Compression, Direct-Drive, ICF Experiments

The success of direct-drive-ignition target designs depends on two issues: the ability to maintain the main fuel entropy at a low level and the control of the nonuniformity growth during the implosion. Modelling the ICF experiments requires an accurate account for all sources of shell heating, including the shock heating, radiation and suprathermal electrons preheat, and small-scale perturbation growth. To increase calculation accuracy, a new heat-transport model has been developed and implemented in the 1-D hydrocode LILAC. This model includes both the effect of the resonance absorption and the nonlocal thermal transport. The OMEGA experiments designed with the help of the new model have achieved high-areal-density pR > 200 mg/cm^2) fuel assembly in the low-adiabat cryogenic shell implosions.

Goncharov, V N↗