Engineering Papers⌕ Search

Engineering topics

Seka, W

Publications and source records attributed to Seka, W.

At least 19 records

Spherical shock-ignition experiments with the 40 + 20-beam configuration on OMEGA

Spherical shock-ignition experiments on OMEGA used a novel beam configuration that separates low-intensity compression beams and high-intensity spike beams. Significant improvements in the performance of plastic-shell, D 2 implosions were observed with repointed beams. The analysis of the coupling of the high-intensity spike beam energy into the imploding capsule indicates that absorbed hot-electron energy contributes to the coupling. The backscattering of laser energy was measured to reach up to 36% at single-beam intensities of ~ 8 x 10 15 W/cm/ 2 . Hard x-ray measurements revealed a relatively low hot-electron temperature of ~30 keV independent of intensity and timing. At the highest intensity, stimulated Brillouin scattering occurs near and above the quarter-critical density and the two-plasmon-decay instability is suppressed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Crossed-beam energy transfer in direct-drive implosions

Direct-drive-implosion experiments on the OMEGA laser [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] have showed discrepancies between simulations of the scattered (non-absorbed) light levels and measured ones that indicate the presence of a mechanism that reduces laser coupling efficiency by 10%-20%. This appears to be due to crossed-beam energy transfer (CBET) that involves electromagnetic-seeded, low-gain stimulated Brillouin scattering. CBET scatters energy from the central portion of the incoming light beam to outgoing light, reducing the laser absorption and hydrodynamic efficiency of implosions. One-dimensional hydrodynamic simulations including CBET show good agreement with all observables in implosion experiments on OMEGA. Three strategies to mitigate CBET and improve laser coupling are considered: the use of narrow beams, multicolor lasers, and higher-Z ablators. Experiments on OMEGA using narrow beams have demonstrated improvements in implosion performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Crossed-beam energy transfer in direct-drive implosions

Direct-drive-implosion experiments on the OMEGA laser [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] have showed discrepancies between simulations of the scattered (non-absorbed) light levels and measured ones that indicate the presence of a mechanism that reduces laser coupling efficiency by 10%-20%. This appears to be due to crossed-beam energy transfer (CBET) that involves electromagnetic-seeded, low-gain stimulated Brillouin scattering. CBET scatters energy from the central portion of the incoming light beam to outgoing light, reducing the laser absorption and hydrodynamic efficiency of implosions. One-dimensional hydrodynamic simulations including CBET show good agreement with all observables in implosion experiments on OMEGA. Three strategies to mitigate CBET and improve laser coupling are considered: the use of narrow beams, multicolor lasers, and higher-Z ablators. Experiments on OMEGA using narrow beams have demonstrated improvements in implosion performance.

36 MATERIALS SCIENCE↗

Fast-electron generation in long-scale-length plasmas

Long-scale-length ({approx}400-{mu}m) planar CH plasmas have been generated on OMEGA EP with laser intensities of the order of 10{sup 14} W/cm{sup 2} and {approx}1-mm focal spots to quantify the number and temperature of fast electrons caused by the two-plasmon-decay instability. The main diagnostics were the time-integrated K{sub {alpha}} line emission and the hard x-ray bremsstrahlung (HXR) from a molybdenum (Mo) substrate. For the intensity range of 1-7 x 10{sup 14} W/cm{sup 2}, the Mo K{sub {alpha}} and HXR energies increased by more than three orders of magnitude. The fast-electron temperature in this range (deduced from the x-ray bremsstrahlung emission) rose from {approx}20 keV to {approx}90 keV. A Monte Carlo code was used to estimate the total energy (or number) of fast electrons based on these two experimental signatures. The resulting energy in fast electrons as a fraction of the laser energy was found to rise in the same intensity range up to {approx}1%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Multiple spherically converging shock waves in liquid deuterium

To achieve ignition, inertial confinement fusion target designs use a sequence of shocks to compress the target before it implodes. To minimize the entropy acquired by the fuel, the strength and timing of these shocks will be precisely set during a series of tuning experiments that adjust the laser pulse to achieve optimal conditions. We report measurements of the velocity and timing of multiple, converging shock waves inside spherical targets filled with liquid (cryogenic) deuterium. These experiments produced the highest reported shock velocity observed in liquid deuterium (U{sub s} = 135 km/s at {approx}25 Mb) and observed an increase in shock velocity due to spherical convergence. These direct-drive experiments are best simulated when hydrodynamic codes use a nonlocal model for the transport of absorbed laser energy from the coronal plasma to the ablation surface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Amplification of light in a plasma by stimulated ion acoustic waves driven by multiple crossing pump beams

Experiments demonstrate the amplification of 351 nm laser light in a hot dense plasma similar to those in inertial confinement fusion ignition experiments. A seed beam interacts with one or two counter-propagating pump beams, each with an intensity of 1.2x10{sup 15} W/cm{sup 2} at 351 nm, crossing the seed at 24.8 deg. at the position where the flow is Mach 1, allowing resonant stimulation of ion acoustic waves. Results show that the energy and power transferred to the seed are increased with two pumps beyond the level that occurs with a single pump, demonstrating that, under conditions similar to ignition experiments where each beam has a low gain exponent, the total scatter produced by the multiple beams can be significantly larger than that of the individual beams. It is further demonstrated that the amplification is greatly reduced when the pump polarization is orthogonal to the seed, as expected from models of stimulated scatter.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Initial cone-in-shell fast-ignition experiments on OMEGA

Fast ignition is a two-step inertial confinement fusion concept where megaelectron volt electrons ignite the compressed core of an imploded fuel capsule driven by a relatively low-implosion velocity. Initial surrogate cone-in-shell, fast-ignitor experiments using a highly shaped driver pulse to assemble a dense core in front of the cone tip were performed on the OMEGA/OMEGA EP Laser [T. R. Boehly et al., Opt. Commun. 133, 495 (1997); L. J. Waxer et al., Opt. Photonics News 16, 30 (2005)]. With optimal timing, the OMEGA EP pulse produced up to {approx}1.4 x 10{sup 7} additional neutrons which is a factor of {approx}4 more neutrons than without short-pulse heating. Shock-breakout measurements performed with the same targets and drive conditions demonstrate an intact cone tip at the time when the additional neutrons are produced. Velocity interferometer system for any reflector measurements show that x-rays from the shell's coronal plasma preheat the inner cone wall of thin-walled Au cones, while the thick-walled cones that are used in the integrated experiments are not affected by preheat.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Velocity and Timing of Multiple Spherically Converging Shock Waves in Liquid Deuterium

The fuel entropy and required drive energy for an inertial confinement fusion implosion are set by a sequence of shocks that must be precisely timed to achieve ignition. This Letter reports measurements of multiple spherical shock waves in liquid deuterium that facilitate timing inertial confinement fusion shocks to the required precision. These experiments produced the highest shock velocity observed in liquid deuterium (U{sub s}=135 km/s at {approx}2500 GPa) and also the first observation of convergence effects on the shock velocity. Simulations model the shock-timing results well when a nonlocal transport model is used in the coronal plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Triple-Picket Warm Plastic-Shell Implosions on OMEGA

Warm deuterium-gas-filled plastic shells are imploded by direct irradiation from the OMEGA laser [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)]. The pulse shapes contain three pickets that precede a sharp rise to a constant laser intensity at ~4.5 x 10^14 W/cm^2. The in-flight-aspect-ratio (IFAR), a crucial measure of shell instability to nonuniformity growth, is varied in these implosions by changing picket energies and the timing among the pickets. Simulations that include cross-beam energy transfer in addition to inverse bremsstrahlung for the laser-energy deposition models show better agreement with measurements of the neutron bang time and temporally resolved scattered light and therefore more correctly model the shell kinetic energy. It is also shown that target performance improves significantly as IFAR is reduced. Nearly twice the neutron yield is measured for IFAR ~ 31 compared to IFAR ~ 60. The ratio of the measured to simulated neutron yield and areal density increases significantly with decreasing IFAR. These implosions unambiguously link target performance to in-flight shell instability attributable to short-wavelength growth and indicate that IFAR ~ 40 is required to achieve adequate compression at this intensity.

Stoeckl, C↗

Crossed-Beam Energy Transfer in Implosion Experiments on OMEGA

Radiative hydrodynamic simulations of implosion experiments on the OMEGA laser system [Boehly et al., Opt. Commun. 133, 495 (1997)] show that energy transfer between crossing laser beams can reduce laser absorption by 10%–20%. A new quantitative model for the crossed-beam energy transfer has been developed, allowing one to simulate the coupling of multiple beams in the expanding corona of implosion targets. Scattered-light and bang-time measurements show good agreement with predictions of this model when nonlocal heat transport is employed. The laser absorption can be increased by narrowing laser beams and/or employing two-color light, which both reduce the crossed-beam energy transfer.

Igumenshchev, I V↗

Crossed-beam energy transfer in implosion experiments on OMEGA

Radiative hydrodynamic simulations of implosion experiments on the OMEGA laser system [Boehly et al., Opt. Commun. 133, 495 (1997)] show that energy transfer between crossing laser beams can reduce laser absorption by 10%-20%. A new quantitative model for the crossed-beam energy transfer has been developed, allowing one to simulate the coupling of multiple beams in the expanding corona of implosion targets. Scattered-light and bang-time measurements show good agreement with predictions of this model when nonlocal heat transport is employed. The laser absorption can be increased by narrowing laser beams and/or employing two-color light, which both reduce the crossed-beam energy transfer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Shock-tuned cryogenic-deuterium-tritium implosion performance on Omega

Cryogenic-deuterium-tritium (DT) target compression experiments with low-adiabat (alpha), multiple-shock drive pulses have been performed on the Omega Laser Facility [T. R. Boehly, D. L. Brown, R. S. Craxton et al., Opt. Commun. 133, 495 (1997)] to demonstrate hydrodynamic-equivalent ignition performance. The multiple-shock drive pulse facilitates experimental shock tuning using an established cone-in-shell target platform [T. R. Boehly, R. Betti, T. R. Boehly et al., Phys. Plasmas 16, 056301 (2009)]. These shock-tuned drive pulses have been used to implode cryogenic-DT targets with peak implosion velocities of 3x10{sup 7} cm/s at peak drive intensities of 8x10{sup 14} W/cm{sup 2}. During a recent series of alphaapprox2 implosions, one of the two necessary conditions for initiating a thermonuclear burn wave in a DT plasma was achieved: an areal density of approximately 300 mg/cm{sup 2} was inferred using the magnetic recoil spectrometer [J. A. Frenje, C. K. Li, F. H. Seguin et al., Phys. Plasmas 16, 042704 (2009)]. The other condition--a burn-averaged ion temperature <T{sub i}>{sub n} of 8-10 keV--cannot be achieved on Omega because of the limited laser energy; the kinetic energy of the imploding shell is insufficient to heat the plasma to these temperatures. A <T{sub i}>{sub n} of approximately 3.4 keV would be required to demonstrate ignition hydrodynamic equivalence [Betti et al., Phys. Plasmas17, 058102 (2010)]. The <T{sub i}>{sub n} reached during the recent series of alphaapprox2 implosions was approximately 2 keV, limited primarily by laser-drive and target nonuniformities. Work is underway to improve drive and target symmetry for future experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Demonstration of the Highest Deuterium-Tritium Areal Density Using Multiple-Picket Cryogenic Designs on OMEGA

The performance of triple-picket deuterium-tritium cryogenic target designs on the OMEGA Laser System [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] is reported. These designs facilitate control of shock heating in low-adiabat inertial confinement fusion targets. Areal densities up to 300 mg/cm{sup 2} (the highest ever measured in cryogenic deuterium-tritium implosions) are inferred in the experiments with an implosion velocity {approx}3x10{sup 7} cm/s driven at peak laser intensities of 8x10{sup 14} W/cm{sup 2}. Extension of these designs to ignition on the National Ignition Facility [J. A. Paisner et al., Laser Focus World 30, 75 (1994)] is presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Implosion Experiments using Glass Ablators for Direct-Drive Inertial Confinement Fusion

Direct-drive implosions with 20-{mu}m-thick glass shells were conducted on the Omega Laser Facility to test the performance of high-Z glass ablators for direct-drive, inertial confinement fusion. The x-ray signal caused by hot electrons generated by two-plasmon-decay instability was reduced by more than {approx}40x and hot-electron temperature by {approx}2x in the glass compared to plastic ablators at ignition-relevant drive intensities of {approx}1x10{sup 15} W/cm{sup 2}, suggesting reduced target preheat. The measured absorption and compression were close to 1D predictions. The measured soft x-ray production in the spectral range of {approx}2 to 4 keV was {approx}2x to 3x lower than 1D predictions, indicating that the shell preheat caused by soft x-rays is less than predicted. A direct-drive-ignition design based on glass ablators is introduced.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Selective Near-UV Ablation of Subgingival Dental Calculus: Measurement of Removal Rates

A noncontact profilometer (laser triangulation) was used to measure the removal rates of subgingival dental calculus irradiated with a frequency-doubled Ti:sapphire laser (60-ns pulse duration, 400-nm wavelength, 10-Hz repetition rate, 7-mJ pulse energy). Profilometer traces before and after irradiation were used to create a removal map with 4-μm axial and 15-μm transverse resolution. Twenty-three teeth (15 with calculus and 8 pristine) were irradiated at 90° and 45° under a cooling water spray with a super-Gaussian beam (~300-μm diameter). Subgingival calculus was selectively removed at 5.6 and 4.0 J/cm2 for 90° and 45°, respecetively, within a range of rates, between 2 to 9 μm/pulse. These ablation rates were constant during these exposures. For comparison, pristine cementum irradiated for 10 min at the same peak fluence and pulse repetition rate showed only craters, 15 to 50 μm deep, corresponding to an equivalent removal rate three orders of magnitude smaller than that obtained for calculus. Pristine enamel was not removed under the same irradiation conditions.

calculus↗

Direct-Drive Inertial Fusion Research at the University of Rochester's Laboratory for Laser Energetics: A Review

This paper reviews the status of direct-drive inertial confinement fusion (ICF) research at the University of Rochester's Laboratory for Laser Energetics (LLE). LLE's goal is to demonstrate direct-drive ignition on the National Ignition Facility (NIF) by 2014. Baseline "all-DT" NIF direct-drive ignition target designs have been developed that have a predicted gain of 45 (1-D) at a NIF drive energy of ~1.6 MJ. Significantly higher gains are calculated for targets that include a DT-wicked foam ablator. This paper also reviews the results of both warm fuel and initial cryogenic-fuel spherical target implosion experiments carried out on the OMEGA UV laser. The results of these experiments and design calculations increase confidence that the NIF direct-drive ICF ignition goal will be achieved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Effect of Condensates and Inner Coatings on the Performance of Vacuum Hohlraum Targets

Experiments on the OMEGA laser system [Boehly et al., Opt. Commun. 133, 495 (1997)] using laser-driven vacuum hohlraum targets show distinct differences between cryogenic (<20 K) and warm targets. The cryogenic targets have 15% lower peak radiation temperatures, and the temporal profile of those temperatures is quite different than in warm targets. The cryogenic targets reflect significantly more (3%–7%) of the laser drive than the warm targets (<1%). The temporal and spectral features of the reflected light from the cryogenic targets show a significantly longer duration and more spectral features than the warm hohlraums. Warm hohlraum targets coated with 2 um of CH replicate the behavior of cryogenic targets. This indicates that the cryogenic hohlraums are affected by the condensation of background gases on the cold hohlraum surface. The most important effect of low-Z material in the hohlraums is that they significantly reduce the x-ray conversion efficiency, resulting in lower hohlraum radiation temperature. The coatings (both CH and condensates) produce long-scale-length, low-Z plasmas that moderately reduce the absorption of laser light in the hohlraums. This causes higher reflectivity and produces hot electrons that generate hard x rays (hv > 20 keV), both of which are detrimental to the performance of hohlraum-driven inertial confinement fusion targets.

Boehly, T R↗