Engineering Papers⌕ Search

Engineering topics

Schiff, Lewis B.

Publications and source records attributed to Schiff, Lewis B..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Large-Amplitude, High-Rate Roll Oscillations of a 65 deg Delta Wing at High Incidence

The IAR/WL 65 deg delta wing experimental results provide both detail pressure measurements and a wide range of flow conditions covering from simple attached flow, through fully developed vortex and vortex burst flow, up to fully-stalled flow at very high incidence. Thus, the Computational Unsteady Aerodynamics researchers can use it at different level of validating the corresponding code. In this section a range of CFD results are provided for the 65 deg delta wing at selected flow conditions. The time-dependent, three-dimensional, Reynolds-averaged, Navier-Stokes (RANS) equations are used to numerically simulate the unsteady vertical flow. Two sting angles and two large- amplitude, high-rate, forced-roll motions and a damped free-to-roll motion are presented. The free-to-roll motion is computed by coupling the time-dependent RANS equations to the flight dynamic equation of motion. The computed results are compared with experimental pressures, forces, moments and roll angle time history. In addition, surface and off-surface flow particle streaks are also presented.

Chaderjian, Neal M.↗
NASA NTRS1996

Numerical Simulation of Forced and Free-to-Roll Delta-Wing Motions

The three-dimensional, Reynolds-averaged, Navier-Stokes (RANS) equations are used to numerically simulate nonsteady vortical flow about a 65-deg sweep delta wing at 30-deg angle of attack. Two large-amplitude, high-rate, forced-roll motions, and a damped free-to-roll motion are presented. The free-to-roll motion is computed by coupling the time-dependent RANS equations to the flight dynamic equation of motion. The computed results are in good agreement with the forces, moments, and roll-angle time histories. Vortex breakdown is present in each case. Significant time lags in the vortex breakdown motions relative to the body motions strongly influence the dynamic forces and moments.

Chaderjian, Neal M.↗
NASA NTRS1995

Analysis of Tangential Slot Blowing on F/A-18 Isolated Forebody

The generation of significant side forces and yawing moments on an F/A-18 fuselage through tangential slot blowing is analyzed using computational fluid dynamics. The effects of freestream Mach number, jet exit conditions, jet length, and jet location are studied. The effects of over- and underblowing on force and moment production are analyzed. Non-time-accurate solutions are obtained to determine the steady-state side forces, yawing moments, and surface pressure distributions generated by tangential slot blowing. Time-accurate solutions are obtained to study the force onset time lag of tangential slot blowing. Comparison with available experimental data from full-scale wind-tunnel and subscale wind-tunnel tests are made. This computational analysis complements the experimental results and provides a detailed understanding of the effects of tangential slot blowing on the flowfield about the isolated F/A-18 forebody. Additionally, it extends the slot-blowing database to transonic maneuvering Mach numbers.

Gee, Ken↗
NASA NTRS1995

Research and technology 1994

Selected research and technology activities at Ames Research Center are summarized. These activities exemplify the Center's varied and productive research efforts for 1994.

Bousman, William G.↗
NASA NTRS1995

Computational Investigation of Tangential Slot Blowing on a Generic Chined Forebody

The effect of tangential slot blowing on the flowfield about a generic chined forebody at high angles of attack is investigated numerically using solutions of the thin-layer, Reynolds-averaged, Navier-Stokes equations. The effects of jet mass now ratios, angle of attack, and blowing slot location in the axial and circumferential directions are studied. The computed results compare well with available wind-tunnel experimental data. Computational results show that for a given mass now rate, the yawing moments generated by slot blowing increase as the body angle of attack increases. It is observed that greater changes in the yawing moments are produced by a slot located closest to the lip of the nose. Also, computational solutions show that inboard blowing across the top surface is more effective at generating yawing moments than blowing outboard from the bottom surface.

Agosta-Greenman, Roxana M.↗
NASA NTRS1995

Progress in Navier-Stokes Simulation of Delta Wing Maneuver Aerodynamics

This paper will summarize recent progress in the numerical simulation of high incidence vortical flow about a generic 65 degree sweep delta wing using the three dimensional, time-dependent, Reynolds averaged, Navier-Stokes (RANS) equations. Computations have been carried out at 15 and 30 degrees angle of attack under subsonic turbulent flow conditions, and compared with experimental data provided by Hanff, Jenkins, and their colleagues. This work has already been published elsewhere and widely disseminated. Computations carried out at 15 degrees angle of attack included static roll angles ranging up to 65 degrees, and a large-amplitude (40 degree), high rate (7 Hz), forced roll motion. There was very good agreement between computed and experimental forces and moments, and static surface pressures. There was a significant hysteresis of the dynamic rolling moment due to the high rate of roll motion. At this angle of attack, no vortex breakdown was observed in the computations or experiment. Computations were also carried out at 30 degrees angle of attack, where vortex breakdown was present in both the computations and experiment. There was overall good agreement in the computed and experimental forces and moments. The static rolling moment varied with roll angle in a highly nonlinear manner, and exhibited three stable trim points and two unstable trim points. This behavior was attributed to the presence of vortex breakdown. Two large-amplitude (30 degrees), high-rate (10 Hz) forced roll motions were computed. The dynamics of the vortex breakdown motion was dramatically visualized by tracking the time-dependent motion of particles released near the delta wing apex. This numerical visualization is analogous to experimental smoke flow techniques. In one of the dynamic cases the breakdown was found to move off the wing, convected downwind of the trailing edge, and later reformed near the trailing edge through an instability of the vortex core. A damped free-to-roll motion was also computed by releasing the wing from rest at 40 degrees of roll. The wing went to the same trim point as in the experiment.

Chaderjian, Neal M.↗
NASA NTRS1994

Numerical simulation of incidence and sweep effects on delta wing vortex breakdown

The structure of the vortical flowfield over delta wings at high angles of attack was investigated. Three-dimensional Navier-Stokes numerical simulations were carried out to predict the complex leeward-side flowfield characteristics, including leading-edge separation, secondary separation, and vortex breakdown. Flows over a 75- and a 63-deg sweep delta wing with sharp leading edges were investigated and compared with available experimental data. The effect of variation of circumferential grid resolution grid resolution in the vicinity of the wing leading edge on the accuracy of the solutions was addressed. Furthermore, the effect of turbulence modeling on the solutions was investigated. The effects of variation of angle of attack on the computed vortical flow structure for the 75-deg sweep delta wing were examined. At moderate angles of attack no vortex breakdown was observed. When a critical angle of attack was reached, bubble-type vortex breakdown was found. With further increase in angle of attack, a change from bubble-type breakdown to spiral-type vortex breakdown was predicted by the numerical solution. The effects of variation of sweep angle and freestream Mach number were addressed with the solutions on a 63-deg sweep delta wing.

INCIDENCE↗
NASA NTRS1994

Forebody Tangential Slot Blowing on an Aircraft Geometry

The effect of forebody tangential slot blowing on the flowfield about an F/A-18 aircraft is investigated numerically using solutions of the Navier-Stokes equations. Computed solutions are obtained for an aircraft geometry which includes the fuselage, a wing with deflected leading-edge flap, empennage, and a faired-over engine inlet. The computational slot geometry corresponds to that used in full-scale wind-tunnel tests. Solutions are computed using flight test conditions and jet mass flow ratios equivalent to wind-tunnel test conditions. The effect of slot location is analyzed by computing two nontime-accurate solutions with a 16-in. slot located 3 in. and 11 in. aft of the nose of the aircraft. These computations resolve the trends observed in the full-scale wind-tunnel test data. The flow aft of the leading-edge extension vortex burst is unsteady. A time-accurate solution is obtained to investigate the flow characteristics aft of the vortex burst, including the effect of blowing on tail buffet.

Gee, Ken↗
NASA NTRS1994

Computational analysis of forebody tangential slot blowing

An overview of the computational effort to analyze forebody tangential slot blowing is presented. Tangential slot blowing generates side force and yawing moment which may be used to control an aircraft flying at high-angle-of-attack. Two different geometries are used in the analysis: (1) The High Alpha Research Vehicle; and (2) a generic chined forebody. Computations using the isolated F/A-18 forebody are obtained at full-scale wind tunnel test conditions for direct comparison with available experimental data. The effects of over- and under-blowing on force and moment production are analyzed. Time-accurate solutions using the isolated forebody are obtained to study the force onset timelag of tangential slot blowing. Computations using the generic chined forebody are obtained at experimental wind tunnel conditions, and the results compared with available experimental data. This computational analysis compliments the experimental results and provides a detailed understanding of the effects of tangential slot blowing on the flow field about simple and complex geometries.

Gee, Ken↗
NASA NTRS1994

Navier-Stokes prediction of large-amplitude forced and free-to-roll delta-wing oscillations

The three-dimensional Reynolds-averaged, Navier-Stokes (RANS) equations are used to numerically simulate nonsteady vortical flow about a 65 degree sweep delta wing at 30 degrees angle of attack. Two large-amplitude, high-rate, forced-roll motions and a damped free-to-roll motion are presented. The free-to-roll motion is computed by coupling the time-dependent RANS equations to the flight dynamic equation of motion. The computed results are compared with experimental forces, moments, and roll-angle time histories. The overall agreement is good. Vortex breakdown is present in each case, which causes significant time lags in the vortex breakdown motions relative to the body motions. This behavior strongly influences the dynamic forces and moments.

Chaderjian, Neal M.↗
NASA NTRS1994

Computational Analysis of Forebody Tangential Slot Blowing on the F/A-18

An overview of the computational effort to analyze forebody tangential slot blowing for use on the F/A-18 aircraft is presented. Tangential slot blowing generates side force and yawing moment which may be used to control the aircraft flying at high angle of attack. Computations using the isolated forebody are obtained at full-scale wind tunnel test conditions for direct comparison with available experimental data. The effects of jet exit conditions, jet length, and jet location are also studied using the isolated forebody. In addition, these computations are used to predict the effect of slot blowing at transonic maneuvering flight conditions. The effects of over- and under-blowing on force and moment production are analyzed. Non-time-accurate solutions are obtained to determine the steady-state side force and yawing moments generated by tangential slot blowing. Time-accurate solutions are obtained to study the force onset time lag of tangential slot blowing. The effect of blowing on the burst point location are then analyzed by obtaining computations using the aircraft geometry, which includes the wing, empennage, and faired-over inlets. The effect of blowing on the buffet loads on the vertical tails are analyzed using time-accurate computations. Comparison with available experimental data from full-scale wind tunnel and sub-scale wind tunnel tests are made. This computational analysis compliments the experimental results and provides a detailed understanding of the effects of tangential slot blowing on the flow field about the F/A-18.

Gee, Ken↗
NASA NTRS1994

Numerical Generation of Asymmetric Flows about Slender Bodies of Revolution at Extreme Incidence

It is well known that slender bodies of revolution will develop an asymmetric, unsteady flow pattern in experimental tests, if the angle of incidence to the oncoming stream is above a critical value. It has been suggested that the origin of these asymmetric flows may stem from geometric imperfections of the model being tested, or from disturbances in the oncoming stream. In numerical simulations, it is possible to generate bodies of revolution which are perfectly symmetric about their longitudinal axis, and to impose uniform flow conditions which are free from disturbances. The current work presents numerical simulations of the flow about an ogive-cylinder configuration at 40 and 60 degree angle of incidence. These simulations. were performed using numerical algorithms which are also symmetric about the lateral plane of the cylinder body. The flowfields at 40 degree angle of attack were seen to remain symmetric to the round-off accuracy of the computer. At 60 degree angle of attack, a lateral force coefficient developed of O(1) which progressed to an alternate vortex shedding in time. The nature of this lateral force generation and vortex shedding was dependent on the choice of numerical algorithm. The origin of the asymmetries observed in the 60 degree angle of attack computations were traced to round-off errors in the implicit block-matrix inverter. A means of inverting the implicit operator matrices, which maintains the symmetry of the overall numerical algorithm was implemented.

Murman, Scott M.↗
NASA NTRS1993

Effect of forebody tangential slot blowing on flow about a full aircraft geometry

The effect of forebody tangential slot blowing on the flowfield about an F/A-18 aircraft is investigated numerically using solutions of the Navier-Stokes equations. Computed solutions are obtained for a full aircraft geometry, including the fuselage, wing with deflected leading-edge flap, empennage, and a faired-over engine inlet. The computational slot geometry corresponds to that used in full-scale wind tunnel tests. Solutions are computed using flight test conditions and jet mass flow ratios equivalent to wind tunnel test conditions. The effect of slot location is analyzed by computing two non-time-accurate solutions with a 16 in. slot located 3 in. and 11 in. aft of the nose of the aircraft. These computations resolve the trends observed in the full-scale wind tunnel test data. The flow aft of the leading edge extension (LEX) vortex burst is unsteady. A time-accurate solution is obtained to investigate the flow characteristics aft of the vortex burst, including the effect of blowing on tail buffet.

Gee, Ken↗
NASA NTRS1993

Navier-Stokes prediction of a delta wing in roll with vortex breakdown

The three-dimensional, Reynolds-averaged, Navier-Stokes (RANS) equations are used to numerically simulate vortical flow about a 65 degree sweep delta wing. Subsonic turbulent flow computations are presented for this delta wing at 30 degrees angle of attack and static roll angles up to 42 degrees. This work is part of an on going effort to validate the RANS approach for predicting high-incidence vortical flows, with the eventual application to wing rock. The flow is unsteady and includes spiral-type vortex breakdown. The breakdown positions, mean surface pressures, rolling moments, normal forces, and streamwise center-of-pressure locations compare reasonably well with experiment. In some cases, the primary vortex suction peaks are significantly underpredicted due to grid coarseness. Nevertheless, the computations are able to predict the same nonlinear variation of rolling moment with roll angle that appeared in the experiment. This nonlinearity includes regions of local static roll instability, which is attributed to vortex breakdown.

Chaderjian, Neal M.↗
NASA NTRS1992

Effects Of Spatial Disturbances On Asymmetries Of Vortexes

Report describes computational study of effects of small spatial disturbances on asymmetries in vortexes downstream of slender bodies of revolution in flows at large angle of attack. Flow phenomena affect stability and maneuvering characteristics of missiles and aircraft. Understanding phenomena helps answer questions as how precisely symmetrical aerodynamic body should be, and how roughness, bumps, or other imperfections affect maneuvering characteristics.

Degani, David↗
NASA NTRS1992

Shedding Of Vortices From A Missilelike Body

Report describing computational study of subsonic flows about slender bodies of revolution focuses on effect of angle of attack on development of unsteadiness in flow - particularly unsteady shedding of vortices on leeward side. At large angles of attack, flows exhibit self-sustained oscillations.

Schiff, Lewis B.↗