Engineering Papers⌕ Search

Engineering topics

Rummler, D. R.

Publications and source records attributed to Rummler, D. R..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Video camera system for locating bullet holes in targets at a ballistics tunnel

A system consisting of a single charge coupled device (CCD) video camera, computer controlled video digitizer, and software to automate the measurement was developed to measure the location of bullet holes in targets at the International Shooters Development Fund (ISDF)/NASA Ballistics Tunnel. The camera/digitizer system is a crucial component of a highly instrumented indoor 50 meter rifle range which is being constructed to support development of wind resistant, ultra match ammunition. The system was designed to take data rapidly (10 sec between shoots) and automatically with little operator intervention. The system description, measurement concept, and procedure are presented along with laboratory tests of repeatability and bias error. The long term (1 hour) repeatability of the system was found to be 4 microns (one standard deviation) at the target and the bias error was found to be less than 50 microns. An analysis of potential errors and a technique for calibration of the system are presented.

Burner, A. W.↗
NASA NTRS1985

Structures and materials technology issues for reusable launch vehicles

Projected space missions for both civil and defense needs require significant improvements in structures and materials technology for reusable launch vehicles: reductions in structural weight compared to the Space Shuttle Orbiter of up to 25% or more, a possible factor of 5 or more increase in mission life, increases in maximum use temperature of the external surface, reusable containment of cryogenic hydrogen and oxygen, significant reductions in operational costs, and possibly less lead time between technology readiness and initial operational capability. In addition, there is increasing interest in hypersonic airbreathing propulsion for launch and transmospheric vehicles, and such systems require regeneratively cooled structure. The technology issues are addressed, giving brief assessments of the state-of-the-art and proposed activities to meet the technology requirements in a timely manner.

Dixon, S. C.↗
NASA NTRS1985

Structures and materials technology issues for reusable launch vehicles

Projected space missions for both civil and defense needs require significant improvements in structures and materials technology for reusable launch vehicles: reductions in structural weight compared to the Space Shuttle Orbiter of up to 25 percent or more, a possible factor of 5 or more increase in mission life, increases in maximum use temperature of the external surface, reusable containment of cryogenic hydrogen and oxygen, significant reductions in operational costs, and possibly less lead time between technology readiness and initial operational capability. In addition, there is increasing interest in hypersonic airbreathing propulsion for launch and transmospheric vehicles, and such systems require regeneratively cooled structure. The technology issues are addressed, giving brief assessments of the state-of-the-art and proposed activities to meet the technology requirements in a timely manner.

Dixon, S. C.↗
NASA NTRS1982

Static calibration for measurement of loads in wind tunnel tests on Shuttle surface tiles

A description is given of the procedures used for the static calibrations of the Coe (1981) sensor array to determine normal force, pitching moment, and rolling moment from the ensemble of sensor outputs. The use of independent data to confirm the validity of the calibration is also described. Two methods are used in calibrating the Coe sensors. In the first, calibration loads and readings are arranged in matrix form and are assumed to be related in a linear fashion. In the second, each Coe sensor reading is regarded as a sum of contributions from each of the calibration loads. It is shown that the Coe load sensors, in conjunction with either of two data analysis methods, can be used to determine the forces and moments experienced by a Shuttle TPS tile.

Rummler, D. R.↗
NASA NTRS1982

Edge softening of the Shuttle TPS strain isolation pad

Tensile tests and an analytical investigation were performed to characterize the edge softening behavior of the strain isolation pad (SIP) between the Orbiter skin and thermal protection system. The tensile tests were carried out with varying sizes of disk-shaped specimens bonded between aluminum disks. The specimens strength and stiffness were determined on the basis of specimen size, and an analytical model of the microstructural stress-strain characteristics was developed. Strength and stiffness were found to decrease near the free edges because through-the-thickness fibers located there were not anchored. No size dependence at maximum load was observed in specimens between 0.75-4.0 in. thick. In-plane and out-of-plane coupling in deformation was detected. The model gave accurate predictions of the tensile behavior of the SIP as a function of distance to a free edge.

Ransone, P. O.↗
NASA NTRS1981

Mass loss of TEOS-coated RCC subjected to the environment at the shuttle wing leading edge

Coated, reinforced carbon-carbon (RCC) is used for the leading edges of the Space Shuttle. The mass loss characteristics of RCC specimens coated with tetra-ethyl-ortho-silicate (TEOS) were determined for conditions which simulated the entry environment expected at the stagnation area of the wing leading edge. Maximum specimen temperature was 1632 K. Specimens were exposed for up to 100 missions. Stress levels up to 8.274 MPa caused an average increase in oxidation of 6 percent over unstressed specimens. Experimentally determined mass losses were compared with those predicted by an existing empirical analysis.

Stroud, C. W.↗
NASA NTRS1981

Low strain creep and aging of aluminum alloy 2219-T87 sheet

The constant load creep and isothermal aging characteristics of aluminum alloy 2219-T87 sheet have been studied experimentally and analytically in the temperature range 250 to 650 F at stress levels between 2.9 and 4.0 ksi (20 to 283 MPa). Testing variables were closely and automatically monitored. The data generated agree somewhat with the literature data base at lower temperatures, but above 500 F, discrepancies of greater than an order of magnitude in the time to 1% creep strain occur. Good correlation was found with the Larson-Miller parameter as modeled by a second-order polynomial in stress. Constitutive equations for time to 0.1%, 0.2%, 0.5%, and 1.0% creep are given. Information on residual mechanical properties and electrical conductivity is also provided.

Navrotski, G.↗
NASA NTRS1980

An approximation to student's t-distribution

Three equations relate Student's t-distribution to standard normal distribution with maximum error of less than 0.8 percent. First equation, used for degrees of freedom (v) greater than 2, expresses t variable in terms of standard normal variable z. For v=1 and 2, second and third equations express t exactly in terms of probability P.

Rummler, D. R.↗
NASA NTRS1980

Mass loss of a TEOS-coated, reinforced carbon-carbon composite subjected to a simulted shuttle entry environment

Coated, reinforced carbon-carbon (RCC) is used for the leading edges of the space shuttle. The mass loss characteristics of RCC specimens coated with tetraethyl orthosilicate (TEOS) were determine for conditions which simulated the environment expected at the lug attachment area of the leading edge. Mission simulation included simultaneous application of load, temperature, and oxygen partial pressure. Maximum specimen temperature was 900 K (1160 F). Specimens were exposed for up to 80 simulated missions. Stress levels up to 6.8 MPa (980 psi) did not significantly affect the mass loss characteristics of the TEOS-coated RCC material. Mass loss was correlated with the bulk density of the specimens.

Stroud, C. W.↗
NASA NTRS1980

Microstructural characterization of the HRSI thermal protection system for space shuttle

Components of the space shuttle high temperature reusable surface insulation (HRSI) system were microscopically characterized, both separately and as a system, to obtain information needed for stress analysis models of the thermal protection system. A tension specimen of the HRSI system was loaded in steps and was microscopically observed at each load condition to demonstrate the tension failure mode associated with strain isolation pad (SIP) behavior. A local failure occurred which should be associated with transfer of load through transverse fibers in the SIP. Stress concentrations attributed to the SIP behavior necessitated strengthening of the HRSI by densification of the RSI at the bondline. An HRSI tile was microscopically characterized after the densification process. The densified surface layer blended into the RSI which caused a gradual change in density. The gradation in density does not appear to represent a sharp discontinuity in elastic modulus between the densified layer and the parent material.

Ransone, P. O.↗
NASA NTRS1980

Room temperature mechanical properties of shuttle thermal protection system materials

Tests were conducted at room temperature to determine the mechanical properties and behavior of materials used for the thermal protection system of the space shuttle. The materials investigated include the LI-900 RSI tiles, the RTV-560 adhesive and the .41 cm (.16 thick) strain isolator pad (SIP). Tensile and compression cyclic loading tests were conducted on the SIP material and stress-strain curves obtained for various proof loads and load cyclic conditioning. Ultimate tensile and shear tests were conducted on the RSI, RTV, and SIP materials. The SIP material exhibits highly nonlinear stress-strain behavior, increased tangent modulus and ultimate tensile strength with increased loading rate, and large short time load relaxation and moderate creep behavior. Proof and cyclic load conditioning of the SIP results in permanent deformation of the material, hysteresis effects, and much higher tensile tangent modulus values at large strains.

Sawyer, J. W.↗
NASA NTRS1979

Mechanical and thermophysical properties of graphite/polyimide composite materials

An on-going program to characterize advanced composites for up to 50,000 hours of exposure to simulated supersonic cruise environments is summarized. Results are presented for up to 25,000 hours of thermal exposure and 10,000 hours of flight simulation at temperatures up to 560K (550 F) with emphasis on HTS/710 graphite/polyimide composite material. Results to date indicate that the maximum use temperature for HTS/710 may be reduced to 505K (450 F) for long-time (1000 hours) application such as the supersonic transport. Preliminary thermophysical properties data for HTS/PMR15 graphite/polyimide were generated. These data include thermal conductivity, thermal expansion, and specific heat from 115K (-252 F) to 590K (600 F) and emittance at room temperature and 590K (600 F). The purpose in generating these data was to validate use of state-of-the-art property measurement methods for advanced graphite fiber reinforced resin matrix composites. Based on results to this point, thermal expansion measurements for composites are most difficult to perform. A high degree of caution in conducting thermal expansion tests and analyzing results is required to produce reliable data.

Rummler, D. R.↗
NASA NTRS1979

Analysis of misalignment in the tension test

Many experimenters fail to appreciate the significance of test system alignment during a tensile test. Poor alignment can increase data scatter and significantly influence some of the test results. In this paper a comprehensive analytical study of the misalignment problem in the plastic strain range is presented and errors caused by misalignment estimated. The results show that the stress-strain curve is not significantly affected by misalignment. However, the strains at the outermost fibers of the specimen cross-section are strongly affected by misalignment. Therefore, the effect of misalignment is most important when properties sensitive to local strain concentrations are being investigated.

Wu, H. C.↗
NASA NTRS1979

Research in structures and materials for future space transportation systems - An overview

The paper provides a review of some of the advances of the past decade in structures and materials that have application to future space transportation systems. The paper concentrates on metallic thermal protection systems and structures which could provide the structural efficiency, reliability, and durability dictated by future space utilization requirements. The need for completely reusable, on-board cryogenic fuel tanks is cited as the most challenging technical opportunity and potential thermostructural concepts for tanks are identified. Other critical areas needing technology advances are discussed. Finally, the unique research opportunities offered by the Shuttle Orbiter experiments program for testing structures and thermal protection systems are explored.

Kelly, H. N.↗
NASA NTRS1977

Radiative metallic thermal protection systems - A status report

During the early stages of the space shuttle program there were a number of technological uncertainties concerning the applicability of metallic thermal protection systems (TPS) to the multimission environment of the shuttle. To resolve the uncertainties and to advance the state-of-the-art, the NASA-Langley Research Center initiated a broad-based technology program to develop metallic TPS over the temperature range from 810 K to 1590 K. Wind tunnel tests conducted to assess the influence of surface/stream interaction of wavy surfaces on the design of metallic TPS indicate small increases in heat flux and surface drag for flow angles less than 20 deg. Analytical and experimental investigations, recently completed, have significantly improved prediction methods for cyclic creep behavior of TPS components repeatedly exposed to complex mission cycles. Thermal/structural concept optimization studies to minimize mass while maintaining structural integrity have led to advanced designs with unit masses which are competitive with those for shuttle RSI. In addition, the durability and reusability of metallic TPS have been repeatedly demonstrated in tests of full-scale systems. The current state-of-the-art strongly suggests that radiative metallic TPS have come of age.

Bohon, H. L.↗
NASA NTRS1976

Creep-Rupture Data Analysis - Engineering Application of Regression Techniques

The results are presented of investigations to apply regression techniques to the development of methodology for creep-rupture data analysis. Regression analysis techniques are applied to the explicit description of the creep behavior of materials for space shuttle thermal protection systems. A regression analysis technique is compared with five parametric methods for analyzing three simulated and twenty real data sets, and a computer program for the evaluation of creep-rupture data is presented.

Rummler, D. R.↗