Engineering Papers⌕ Search

Engineering topics

Ren, Yang

Publications and source records attributed to Ren, Yang.

At least 433 records · Page 24

Tuning Li-Ion Diffusion in α-LiMn 1– x Fe x PO 4 Nanocrystals by Antisite Defects and Embedded β-Phase for Advanced Li-Ion Batteries

Olivine-structured LiMn1-xFexPO4 has become a promising candidate for cathode materials owing to its higher working voltage of 4.1 V and thus larger energy density than that of LiFePO4, which has been used for electric vehicles batteries with the advantage of high safety but disadvantage of low energy density due to its lower working voltage of 3.4 V. One drawback of LiMn1-xFexPO4 electrode is its relatively low electronic and Li-ionic conductivity with Li-ion one-dimensional diffusion. Herein, olivine-structured α-LiMn0.5Fe0.5PO4 nanocrystals were synthesized with optimized Li-ion diffusion channels in LiMn1-xFexPO4 nanocrystals by inducing high concentrations of Fe2+-Li+ antisite defects, which showed impressive capacity improvements of approaching 162, 127, 73, and 55 mAh g-1 at 0.1, 10, 50, and 100 C, respectively, and a long-term cycling stability of maintaining about 74% capacity after 1000 cycles at 10 C. By using high-resolution transmission electron microscopy imaging and joint refinement of hard X-ray and neutron powder diffraction patterns, we revealed that the extraordinary high-rate performance could be achieved by suppressing the formation of electrochemically inactive phase (β-LiMn1-xFexPO4, which is first reported in this work) embedded in α-LiMn0.5Fe0.5PO4. Because of the coherent orientation relationship between β- and α- phases, the β-phase embedded would impede the Li+ diffusion along the [100] and/or [001] directions that was activated by the high density of Fe2+-Li+ antisite (4.24%) in α-phase. Thus, by optimizing concentrations of Fe2+-Li+ antisite defects and suppressing β-phase-embedded olivine structure, Li-ion diffusion properties in LiMn1-xFexPO4 nanocrystals can be tuned by generating new Li+ tunneling. These findings may provide insights into the design and generation of other advanced electrode materials with improved rate performance.

25 ENERGY STORAGE↗

In-situ studies of large magnetostriction in DyCo 2 compound by synchrotron-based high-energy X-ray diffraction

Synchrotron-based high-energy X-ray diffraction is used to explore the physical origin of large magnetostriction in DyCo 2 , an RT 2 compound (R = rare earth, T = Co, Fe), by tracing the crystal structural change as a function of temperature and magnetic field. When the DyCo 2 compound is zero-field cooled down below the Curie temperature T C , the high-temperature cubic lattice is distorted into a tetragonal structure, associated with an expansion of unit cell volume. When a magnetic field is applied gradually from 0 to 6 T below T C , no changes in the peak positions for tetragonal (800) T and (008) T peaks are observed, whereas their relative peak intensities are gradually changed. The intensity changes generated during magnetic field increasing are reversed stepwise with decreasing the magnetic field. Our experimental results suggest that the large magnetostriction in DyCo 2 is caused by the crystallographic domain-switch mechanism (or rearrangement of tetragonal domains). In conclusion, the diffraction elastic strain is not detected under the field up to 6 T. The present investigations provide a fundamental understanding of the mechanisms of the large magnetostriction in RT 2 compounds with Laves phases.

36 MATERIALS SCIENCE↗

Cation–Eutectic Transition via Sublattice Melting in CuInP 2 S 6 /In 4/3 P 2 S 6 van der Waals Layered Crystals

Single crystals of the van der Waals layered ferrielectric material CuInP 2 S 6 spontaneously phase separate when synthesized with Cu deficiency. In this paper, we identify a route to form and tune intralayer heterostructures between the corresponding ferrielectric (CuInP 2 S 6 ) and paraelectric (In 4/3 P 2 S 6 ) phases through control of chemical phase separation. We conclusively demonstrate that Cu-deficient Cu 1–x In 1+x/3 P 2 S 6 forms a single phase at high temperature. We also identify the mechanism by which the phase separation proceeds upon cooling. Above 500 K both Cu + and In 3+ become mobile, while P 2 S 6 4– anions maintain their structure. We therefore propose that this transition can be understood as eutectic melting on the cation sublattice. Such a model suggests that the transition temperature for the melting process is relatively low because it requires only a partial reorganization of the crystal lattice. As a result, varying the cooling rate through the phase transition controls the lateral extent of chemical domains over several decades in size. At the fastest cooling rate, the dimensional confinement of the ferrielectric CuInP 2 S 6 phase to nanoscale dimensions suppresses ferrielectric ordering due to the intrinsic ferroelectric size effect. Finally, intralayer heterostructures can be formed, destroyed, and re-formed by thermal cycling, thus enabling the possibility of finely tuned ferroic structures that can potentially be optimized for specific device architectures.

2D ferrielectric↗

Preparation and characterization of high Curie-temperature piezoelectric ceramics in a new Bi-based perovskite of (1 - x )PbTiO 3 - x Bi(Zn 1/2 Hf 1/2 )O 3

To meet the increasing demand for high temperature piezoelectric actuator and transducer applications, much attention has been paid on exploring piezoelectric materials which can work efficiently under high temperature conditions. In the present study, a new Bi-based perovskite (ABO 3 ) of (1 - x)PbTiO 3 -xBi(Zn 1/2 Hf 1/2 )O 3 has been investigated. For the compositions of x < 0.20, it is interesting to observe that the tetragonality (c/a) remains relatively constant over the entire tetragonal phase. This unusual phenomenon is in contrast to the behavior of most PbTiO 3 -based solid solutions, wherein the c/a is usually reduced. As a result, the Curie temperature (T C ) increases from 490 °C for pure PbTiO 3 , to as high as 528 °C for x = 0.10, indicating the present PbTiO 3 -Bi(Zn 1/2 Hf 1/2 )O 3 to be a high-T C piezoelectric material. Finally, it is proposed that the maintained large tetragonality and high TC could be attributed to the large spontaneous polarization (P S ) displacements induced by the strong Pb/Bi-O hybridization and coupling interactions between Pb/Bi and B-site ferroelectric-active cations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Burning lithium in CS 2 for high-performing compact Li 2 S–graphene nanocapsules for Li–S–batteries

Here, tremendous efforts have been made to design the cathode of Li–S batteries to improve their energy density and cycling life. However, challenges remain in achieving fast electronic and ionic transport while accommodating the significant cathode volumetric change, especially for the cathode with a high practical mass loading. Here we report a cathode architecture, which is constructed by burning lithium foils in a CS 2 vapour. The obtained structure features crystalline Li 2 S nanoparticles wrapped by few-layer graphene (Li 2 S@graphene nanocapsules). Because of the improvement on the volumetric efficiency for accommodating sulfur active species and electrical properties, the cathode design enables promising electrochemical performance. More notably, at a loading of 10 mg Li 2 S cm –2 , the electrode exhibits a high reversible capacity of 1,160 mAh g –1 s, namely, an area capacity of 8.1 mAh cm –2 . Li 2 S@graphene cathode demonstrates a great potential for Li-ion batteries, where the Li 2 S@graphene-cathode//graphite-anode cell displays a high capacity of 730 mAh g –1 s as well as stable cycle performance.

25 ENERGY STORAGE↗

Insights into the structural effects of layered cathode materials for high voltage sodium-ion batteries

Cathode materials are critical to the energy density, power density and safety of sodium-ion batteries (SIBs). Herein, we performed a comprehensive study to elucidate and exemplify the interplay mechanism between phase structures, interfacial microstrain and electrochemical properties of layered-structured Na x Ni 1/3 Co 1/3 Mn 1/3 O 2 cathode materials for high voltage SIBs. The electrochemical test results showed that Na x Ni 1/3 Co 1/3 Mn 1/3 O 2 with an intergrowth P2/O3/O1 structure demonstrates better electrochemical performance and better thermal stability than Na x Ni 1/3 Co 1/3 Mn 1/3 O 2 with P2/O3 binary-phase integration and Na x Ni 1/3 Co 1/3 Mn 1/3 O 2 where only the P phase is dominant. This result is caused by the distinct interfacial microstrain development during the synthesis and cycling of the P2/O3/O1 phase. In operando high energy X-ray diffraction further revealed that the intergrowth P2/O1/O3 cathode can inhibit the irreversible P2–O2 phase transformation and simultaneously improve the structure stability of the O3 and O1 phases during cycling. Here, we believe that interfacial microstrain can serve as an indispensable bridge to guide future design and synthesis of high performance SIB cathode materials and other high energy battery materials.

25 ENERGY STORAGE↗

Polymorphism in a high-entropy alloy

Polymorphism, which describes the occurrence of different lattice structures in a crystalline material, is a critical phenomenon in materials science and condensed matter physics. Recently, configuration disorder was compositionally engineered into single lattices, leading to the discovery of high-entropy alloys and high-entropy oxides. For these novel entropy-stabilized forms of crystalline matter with extremely high structural stability, is polymorphism still possible? Here by employing in situ high-pressure synchrotron radiation X-ray diffraction, we reveal a polymorphic transition from face-centred-cubic (fcc) structure to hexagonal-close-packing (hcp) structure in the prototype CoCrFeMnNi high-entropy alloy. The transition is irreversible, and our in situ high-temperature synchrotron radiation X-ray diffraction experiments at different pressures of the retained hcp high-entropy alloy reveal that the fcc phase is a stable polymorph at high temperatures, while the hcp structure is more thermodynamically favourable at lower temperatures. Lastly, as pressure is increased, the critical temperature for the hcp-to-fcc transformation also rises.

36 MATERIALS SCIENCE↗

High-Performance High-Loading Lithium-Sulfur Batteries by Low Temperature Atomic Layer Deposition of Aluminum Oxide on Nanophase S Cathodes

This study examines the effects of nanophase S and surface coatings via atomic layer deposition (ALD) on high-loading sulfur cathodes for developing high-performance and high-energy lithium-sulfur (Li-S) batteries. It is first verified that ball milling is an effective and facile route for nanoengineering microsized S powders and the resultant nanoscale S particles exhibit better performance. Using these ball milled nanoscale S cathodes, it is found that ALD Al2O3 performed at 50 degrees C yields deposits that evolve with ALD cycles from dispersed nanoparticles, to porous, connected films, and finally to dense and continuous films. Moreover, this low temperature ALD process suppresses S loss by sublimation. The ALD Al2O3 greatly improves sulfur cathode sustainable capacity and Coulombic efficiency. This study postulates two different mechanisms underlying the effects of ALD Al2O3 surface coatings depending on their morphology. ALD Al2O3 nanoparticles dispersed on the sulfur surface mainly function to adsorb polysulfides, thereby inhibiting S shuttling and improving sustainable capacity and Coulombic efficiency. By contrast, ALD Al2O3 films behave as a physical barrier to prevent polysulfides from contacting the liquid electrolyte and dissolving. The dispersed Al2O3 nanoparticles improve both sustainable capacity and Coulombic efficiency while the closed Al2O3 films improve Coulombic efficiency while decreasing the capacity

25 ENERGY STORAGE↗

Ferro-Lattice-Distortions and Charge Fluctuations in Superconducting LaO 1- x F x BiS 2

Competing ferroelectric and charge density wave states have been proposed to exist in the electron–phonon coupled LaO1-xFxBiS2 superconductor. The lattice instability is proposed to arise from unstable phonon modes that can break the crystal symmetry. Using single crystal diffraction, a superlattice pattern is observed, that arises from coherent in-plane displacements of the sulfur atoms in the BiS2 superconducting planes. The distortions morph into coordinated ferrodistortive patterns with displacements in the x- and y-directions, that alternate along the c-axis. Diffuse scattering is observed along the (H0L) plane due to stacking faults but not along the (HH0) plane. The ferro-distortive pattern remains in the superconducting state upon fluorine doping, but the displacements are diminished in magnitude. Moreover, we find that the in-plane distortions give rise to disorder where the (00L) reflections become quite broad. It is possible that charge carriers can get trapped in the lattice deformations reducing the effective number of carriers available for pairing.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Optimizing the coupled effects of Hall-Petch and precipitation strengthening in a Al 0.3 CoCrFeNi high entropy alloy

A successful demonstration of applying integrated strengthening using Hall-Petch strengthening (grains size effect) and precipitation strengthening is shown in the fcc based high entropy alloy (HEA) Al0.3CoCrFeNi, leading to quantitative determinations of the Hall-Petch coefficients for both hardness and tensile yield strength, aswell as the enhancements in the yield strength fromtwo distinct types of ordered precipitates, L12 and B2. An excellent combination of yield strength (~490MPa), ultimate tensile strength (~850MPa), and ductility (~45% elongation) was achieved by optimizing and coupling both strengtheningmechanisms, resulting from a refined grain size as well as both L12 and B2 ordered precipitates. This opens up new avenues for the future development of HEAs, with the appropriate balance of properties required for engineering applications.

Gwalani, B.↗

Revealing mechanism responsible for structural reversibility of single-crystal VO 2 nanorods upon lithiation/delithiation

A pure phase of VO 2 (B) nanorods have been synthesized through an energy-efficient microwave hydrothermal reaction and used as cathode materials of lithium ion batteries, which exhibit promising specific capacity (e.g., 130 mA h g -1 even after 100 charge/discharge cycles) and rate capacity (e.g., ~130 mA h g -1 at a high current of 400 mA g -1 ). The excellent cyclability originates from the structural reversibility of VO 2 (B) upon lithiation/delithiation that is confirmed by the in situ high-energy synchrotron X-ray diffraction (HEXRD) and in situ x-ray adsorption near-edge spectroscopy (XANES) of the VO 2 nanorods in operating battery cells. As a result, the real-time results reveal that discharge forces lithium ions to insert firstly into the tunnels with the largest size along b direction followed by the second largest tunnels along c direction, which is completely reversible in the charge process.

36 MATERIALS SCIENCE↗

Structure and reactivity of Pt–In intermetallic alloy nanoparticles: Highly selective catalysts for ethane dehydrogenation

The structure of silica supported Pt and Pt-In bimetallic catalysts with nominal In: Pt atomic ratios of 0.7 and 1.4 were here determined by in situ synchrotron XAS and XRD. It was seen that the addition of In led to the formation of two different intermetallic alloy phases. At an In: Pt ratio of 0.7 the Pt 3 In phase with a Cu 3 Au structure was formed. When the ratio was increased to 1.4 a shell of PtIn 2 having a CaF 2 structure formed around a core of Pt 3 In. The catalysts were tested for ethane dehydrogenation at 600° to determine the effect of alloying on ethylene selectivity and turnover rate (TOR). The monometallic Pt catalysts was 73% selective for ethylene and had an initial TOR of 0.7 s -1 . Both alloy catalysts were approximate to 100% selective for dehydrogenation and had higher initial TOR, 2.8 s -1 and 1.6 s -1 for In: Pt ratio of 0.7 and 1.4, respectively. The increase in selectivity is attributed to the elimination of large Pt ensembles resulting from geometric changes to the catalyst surface upon alloying. Electronic changes due to the formation of Pt-In bonds are thought to be responsible for the increases in TOR in the alloy catalysts.

36 MATERIALS SCIENCE↗

High-pressure floating-zone growth of perovskite nickelate LaNiO 3 single crystals

We report the first single crystal growth of the correlated metal LaNiO 3 using a high-pressure optical-image floating zone furnace. The crystals were studied using single crystal/powder X-ray diffraction, resistivity, specific heat, and magnetic susceptibility. The availability of bulk LaNiO 3 crystals will (i) promote deep understanding in this correlated material, including the mechanism of enhanced paramagnetic susceptibility, and (ii) provide rich opportunities as a substrate for thin film growth such as important ferroelectric and/or multiferroic materials. As a result, this study demonstrates the power of high pO 2 single crystal growth of nickelate perovskites and correlated electron oxides more generally.

36 MATERIALS SCIENCE↗

A high-voltage rechargeable magnesium-sodium hybrid battery

Growing global demand of safe and low-cost energy storage technology triggers strong interests in novel battery concepts beyond state-of-art Li-ion batteries. Here we report a high-voltage rechargeable Mg–Na hybrid battery featuring dendrite-free deposition of Mg anode and Na-intercalation cathode as a low-cost and safe alternative to Li-ion batteries for large-scale energy storage. A prototype device using a Na3V2(PO4)3 cathode, a Mg anode, and a Mg–Na dual salt electrolyte exhibits the highest voltage (2.60 V vs. Mg) and best rate performance (86% capacity retention at 10C rate) among reported hybrid batteries. Synchrotron radiation-based X-ray absorption near edge structure (XANES), atomic-pair distribution function (PDF), and high-resolution X-ray diffraction (HRXRD) studies reveal the chemical environment and structural change of Na3V2(PO4)3 cathode during the Na ion insertion/deinsertion process. XANES study shows a clear reversible shift of vanadium K-edge and HRXRD and PDF studies reveal a reversible two-phase transformation and V–O bond length change during cycling. The energy density of the hybrid cell could be further improved by developing electrolytes with a higher salt concentration and wider electrochemical window. This work represents a significant step forward for practical safe and low-cost hybrid batteries.

Li, Yifei↗

Unravelling the origin of irreversible capacity loss in NaNiO 2 for high voltage sodium ion batteries

Layered transition metal compounds have attracted much attention due to their high theoretical capacity and energy density for sodium ion batteries. However, this kind of material suffers from serious irreversible capacity decay during the charge and discharge process. Here, using synchrotron-based operando transmission X-ray microscopy and high-energy X-ray diffraction combined with electrochemical measurements, the visualization of the dissymmetric phase transformation and structure evolution mechanism of layered NaNiO2 material during initial charge and discharge cycles are clarified. Phase transformation and deformation of NaNiO2 during the voltage range of below 3.0 V and over 4.0 V are responsible for the irreversible capacity loss during the first cycling, which is also confirmed by the evolution of reaction kinetics behavior obtained by the galvanostatic intermittent titration technique. These findings reveal the origin of the irreversibility of NaNiO2 and offer valuable insight into the phase transformation mechanism, which will provide underlying guidance for further development of high-performance sodium ion batteries.

high voltage↗