Engineering Papers⌕ Search

Engineering topics

Reese, Matthew O.

Publications and source records attributed to Reese, Matthew O..

24 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Investigating the Role of Copper in Arsenic Doped Cd(Se,Te) Photovoltaics

The open circuit voltage (VOC) deficit in Cd(Se,Te)-based photovoltaics remains a critical obstacle for pushing the technology closer to theoretical performance limits. Arsenic doping has become a dominant and promising route to achieve the higher p-type carrier concentrations necessary for higher VOC, but challenges associated with this alternate defect chemistry and higher doping density have hindered progress. Here we show that while arsenic doping enables high carrier concentrations (>1016 cm-3), co-doping with copper can provide a boost to VOC without a significant change to carrier concentration. A large data set is initially used to explore current-voltage and capacitance-voltage trends associated with arsenic doped devices with and without copper. A smaller subset is then used to probe these trends using a wide variety of characterization techniques. Copper is found to facilitate reduced interface recombination and potentially improved bulk absorber characteristics, though the mechanisms for these improvements are not yet clear. Despite the improved performance of co-doped devices, VOC is still far below its potential especially for highly doped devices. Low emitter doping in conjunction with high absorber doping seems to be a plausible cause for this significant deficit, though other device properties may exacerbate this problem.

CdSeTe↗
DOE OSTI2022

Package Development for Reliability Testing of Perovskites

Metal halide perovskite solar cells have reached a critical point in their development. At a current certified record efficiency of 25.7% for a single-junction, research-scale cell, they now garner serious attention from the solar cell industry as a promising route to widespread, low-cost photovoltaics in single- or tandem-junction configurations. However, more work to demonstrate their durability under real-world outdoor test conditions is necessary to ensure the long-term success and deployment of the technology. Differences in chemistry, processes, and their combination result in unique performance limiters for both efficiency and stability. Further, as many active formulations and layer/cell stack combinations are sensitive to temperature, air, and moisture, it is important to separate intrinsic limitations to stability relative to these extrinsic sources. This presents a particular need for the development of an appropriate and reliable package for environmental (i.e., accelerated and outdoor) testing that will permit these different factors to be evaluated and understood.

14 SOLAR ENERGY↗
DOE OSTI2022

Building Perovskite Solar Cells That Last

Invited perspective on a study performed by Zhao et al. that discusses the importance of that work, which provides a demonstration of intrinsic stability to heat and light through the elimination of multiple degradation pathways that are often observed by metal halide perovskite solar cells, and frames its place in the greater context of the overall field.

durability↗
DOE OSTI2022

Embodied energy and carbon from the manufacture of cadmium telluride and silicon photovoltaics

Here, looking beyond the traditional cost and efficiency metrics of photovoltaics (PV), this work evaluates the impact of embodied energy, embodied carbon, and energy payback time of two dominant technologies (CdTe and Si) on global decarbonization goals. The relative effects of PV technology type, technological advances, energy grid mix, and recycling are evaluated in terms of fostering decarbonization goals. If the highest carbon-intensity scenarios are realized, 2%-14% of the remaining estimated global carbon budget might be consumed to manufacture modules without including their balance of systems. Applying a carbon cost indicates that CdTe might have an additional value of $\$$0.02-$\$$0.04/W relative to Si PV manufactured with the same energy mix. Due to the scale of the challenge, any actions leading to an increased deployment of thin-film PV and/or a significant decrease in the deployed PV's embodied carbon through changing the manufacturing grid mix have demonstrable value in helping the world stay within its remaining estimated carbon budget.

14 SOLAR ENERGY↗
DOE OSTI2022

Evaluation of PbTe and SnTe as Ohmic Contact Layers in CdTe Solar Cell Devices

For solar cells based on CdTe, the choice of a suitable back contact material is limited by CdTe's deep work function. Here, we explored p-type PbTe and SnTe as ohmic contacts to CdTe. These contact layers were grown on single crystal CdTe substrates by molecular beam epitaxy, and the valence band offset between film and substrate was measured using X-ray photoemission spectroscopy. Polycrystalline device structures were also grown by sublimation to assess performance improvements. Doping was achieved in PbTe by thallium incorporation. Only the highest Tl doped PbTe resulted in a desirable band alignment with the CdTe, forming an electron reflector and no hole barrier. Time-resolved photoluminescence measurements also revealed significant photocarrier lifetime improvements for only the highest doped PbTe. Consequentially, devices incorporating the highest doped PbTe layers showed increased power conversion efficiency, primarily from increased fill factor. Doping of the PbTe was measured via Hall effect with variable magnetic field, which was required due to the formation of an n-type parasitic interface layer. To properly interpret the variable field Hall measurements, we derived an expression for the magnetic field-dependent conductivity tensor of an L-valley semiconductor.

anisotropic band valley↗