Engineering Papers⌕ Search

Engineering topics

Ramsey, P. E.

Publications and source records attributed to Ramsey, P. E..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Experimental Flow Models for SSME Flowfield Characterization

Full scale flow models with extensive instrumentation were designed and manufactured to provide data necessary for flow field characterization in rocket engines of the Space Shuttle Main Engine (SSME) type. These models include accurate flow path geometries from the pre-burner outlet through the throat of the main combustion chamber. The turbines are simulated with static models designed to provide the correct pressure drop and swirl for specific power levels. The correct turbopump-hot gas manifold interfaces were designed into the flow models to permit parametric/integration studies for new turbine designs. These experimental flow models provide a vehicle for understanding the fluid dynamics associated with specific engine issues and also fill the more general need for establishing a more detailed fluid dynamic base to support development and verification of advanced math models.

Abel, L. C.↗
NASA NTRS1978

Aerodynamic roll characteristics of a 0.00548 scale 146-inch solid rocket booster reentry configuration (MSFC Model Number 486) over a portion of the reentry flight regime in the NASA MSF 14-inch trisonic wind tunnel

An experimental investigation was conducted in the MSFC 14 inch TWT to study the roll characteristics of a 0.00548 scale model of the 146 inch shuttle solid rocket booster to obtain more accurate rolling moment data on the solid rocket booster. A sensitive single component roll balance was utilized. Data were obtained for a single nose mounted sting. The angle of attack range consisted of angles from 150 deg to 190 deg; roll angles consisted of angles from 0 deg to 337 1/2 deg in increments of 22 1/2 deg; and Mach numbers were 1.46, 1.96, 2.74 and 2.48.

Ramsey, P. E.↗
NASA NTRS1976

Aerodynamic characteristics of a 0.00563 scale 142-inch diameter solid rocket booster (MSFC model 449 and 480) with side mounted stings in the NASA/MSFC 14-inch trisonic wind tunnel (SA14FA)

An experimental investigation (SA14FA, TWT 620) was conducted in the MSFC 14-inch Trisonic Wind Tunnel (TWT) to determine the entry static stability of a 0.00563 scale shuttle solid rocket booster (SRB). The primary objective was to determine the effects of four side mounted sting configurations and to improve the definition of the aerodynamic characteristics in the vicinity of the SRB entry trim point. Data were obtained for two 60 and two 90 degree side mounted stings and a straight nose mounted sting. The angle of attack range for the side-mounted stings was 100 to 170 degrees while that for the nose mounted sting was 150 to 170 degrees. The Mach number range consisted of 0.6 to 3.48. Except for the aft attach ring, no protuberances were considered and the side slip and roll angles were zero. The test model was scaled from the 142-inch diameter SRB known as configuration 139 which was used during test TWT 572 (SA5F).

Ramsey, P. E.↗
NASA NTRS1976

An investigation of the aerodynamic characteristics of a 0.00548 scale model (model no. 486) of the space shuttle 146-inch diameter solid rocket booster at angels of attack from 113 deg to 180 deg in the AEDC PWT 4-foot transonic wind tunnel (SA16F)

An experimental investigation (SA16F) was conducted in the AEDC PWT 4T to determine the entry static stability of a 0.00548 scale space shuttle solid rocket booster (SRB). The primary objective was to improve the definition of the aerodynamic characteristics in the angle of attack range beyond 90 deg in the vicinity of the entry trim point. The SRB scale model consisted of the reentry configuration with all major protuberances. A simulated heat shield around the engine nozzle was also included. Data were obtained for a 60 deg side mounted sting and a straight nose mounted sting. The angle of attack range for the side mounted sting was 113 deg to 147 deg and for the nose mounted sting 152 deg to 187 deg. The Mach number range consisted of 0.4 to 1.2 at roll angles of 0 and 90 deg. The resulting 6-component aerodynamic force data was presented as the variation of coefficients with angle of attack for each Mach number and roll angle.

Ramsey, P. E.↗
NASA NTRS1976

An investigation to determine the pressure distribution on the 0.0137 scale solid rocket booster forebody (MSFC model 467) at angles of attack at or near 90 deg and high Reynolds numbers in the MSFC High Reynolds Number Wind Tunnel (SA29F)

An aerodynamic investigation was conducted in the MSFC High Reynolds Number Wind Tunnel to determine the pressure distribution over the foresection of the current 146 inch diameter shuttle SRB. The test model consisted of a 0.0137 scale version of the SRB nose cone and a forward portion of the cylindrical body which was approximately 2.7 calibers in length. The pressure distributions are plotted as a function of longitudinal station ratioed to body diameter and circumferential location for each angle of attack and Mach number. A Reynolds number variation study was made for Mach numbers of 0.4 and 0.6 at an angle of attack of 270 deg and roll angle of 180 deg.

Ramsey, P. E.↗
NASA NTRS1976

An investigation of drag reduction fairings on the space shuttle vehicle 5 configuration (model 74-OTS) in the MSFC 14 inch trisonic wind tunnel (FA14)

An experimental investigation was conducted in the MSFC 14-inch TWT (FA14, TWT 600) to determine the static stability and drag on a 0.004 scale model of the shuttle ascent configuration. The primary objective was to study the possibility of reducing the launch vehicle drag by using Orbiter/ET/SRB fairings, streamlined orbiter fore and aft attach structures, SRB and ET alternative nose configurations, and devices for modifying the flow between the orbiter and ET. The secondary objective was to determine the longitudinal and directional characteristics of the ascent configuration with the most promising of the drag reduction devices installed. Data were obtained for a Mach number range of 0.6 through 4.96 and angles of attack from -5 through 5 degrees at zero degrees side slip angle.

Ramsey, P. E.↗
NASA NTRS1975

An investigation of the 0.0091 scale External Tank ogive nose (MSFC model 470) in the MSFC 14 inch TWT to determine the pressure distribution around the External Tank Nose (TA3F), volume 1

The model tested was a 0.0091 scale representation of the ogive nose section of the External Tank with nose cap and lightning rod and protuberances. Pressure distribution around the nose cap was determined. Pressure data were also obtained along the ogive nose. Data were obtained over an angle of attack range of + or -5 degrees and over a Mach number range of .6 to 4.96. The Reynolds number per unit length (ft.) ranged from 4.1 million to 4.96 million. There were 22 pressure ports in a single row. Circumferential positions of 0, 22.5, 45, 67.5 and 90 degrees were simulated by rotating the model. The LO2 feed line and LO2 recirculation line were simulated. The effects of the nose spike were investigated over a range of Mach numbers. The data will be useful for venting analyses. Photographs showing flow visualization of the test configuration are given.

Ramsey, P. E.↗
NASA NTRS1975

Results of an Investigation of the 0.003-scale Space Shuttle External Tank MSFC Model 460 in the NASA/MSFC 14 x 14-inch Trisonic Wind Tunnel to Determine Static Pressure Distributions During Reentry (TA2F), Volume 1

Objectives of the test were to obtain static pressure distributions for the ET at reentry conditions. Basic configuration of the model was the MCR 0200 ET modified to include a rectangular crossbar at the aft ET/orbiter attach point. Mach numbers were 1.96, 3.48, and 4.96. Reynolds number per foot at these Mach numbers were 6.95 million, 6.42 million, and 4.95 million, respectively. Angle of attack range was -8 to 100 degrees and roll angle was 0 to 315 degrees. Occupancy hours were 104.

Ramsey, P. E.↗
NASA NTRS1975

Results of an investigation of the 0.003-scale space shuttle external tank MSFC model 460 in the NASA/MSFC 14 x 14 inch Trisonic Wind Tunnel to determine static pressure distributions during reentry (TA2F), volume 3

Static pressure distributions for the external tank (ET) at reentry conditions are presented. Basic configuration of the model was the MCR 0200 ET modified to include a rectangular crossbar at the aft ET/orbiter attach point. Mach numbers were 1.96, 3.48, and 4.96. Reynolds number per foot at these Mach numbers were 6.95 million, 6.42 million, and 4.95 million, respectively. Angle of attack range was -8 to 100 degrees and roll angle was 0 to 315 degrees.

Ramsey, P. E.↗
NASA NTRS1975

An investigation in the NASA MSFC 14-inch trisonic wind tunnel to determine the pressure distribution over the components of a 0.004 scale version of the Rockwell MCR 0074 baseline shuttle ascent configuration (IA32F), volume 1

Data were obtained for Mach numbers from 0.6 to 3.48, angles of attack from -10 to 10 degrees, and angles of sideslip from -10 to 10 degrees at zero angle of attack. Also, -4 and 4 degrees sideslip were run for an angle of attack of -5 and 5 degrees. Aerodynamic configurations of the solid rocket motors, external tank, and orbiter are shown. Graphs of plotted pressure data (pressure coefficients) for the external tank and solid rocket motors are given. A description of the test facility is included.

Ramsey, P. E.↗
NASA NTRS1974

Triple balance test of the PRR baseline space shuttle configuration on a .004 scale model of the MCR 0074 orbiter configuration in the MSFC 14 x 14 inch Trisonic Wind Tunnel (TWT 570) IA31F(B), volume 1

A wind tunnel force and moment test of the space shuttle launch vehicle was conducted. The wind tunnel model utilized a triple balance such that component aerodynamics of the orbiter, external tank, and solid rocket booster was obtained. The test was conducted at an angle of attack range from -10 deg to 10 deg, and angle of sideslip range from -10 deg to 10 deg, and a Mach number range from 0.6 to 4.96. Simulation parameters to be used in future launch vehicle wind tunnel tests were investigated. The following were included: (1) effect of orbiter -ET attach hardware; (2) model attachment (spacer) effects; (3) effects of grit on model leading surfaces; and (4) model misalignment effects. The effects of external tank nose shape was studied by investigating five different nose configurations. Plotted and tabulated data is reported.

Ramsey, P. E.↗