Engineering topics

Povinelli, L. A.

Publications and source records attributed to Povinelli, L. A..

At least 37 records · Page 2

NASA NTRS1985

Assessment of three-dimensional inviscid codes and loss calculations for turbine aerodynamic computations

An assessment of several three dimensional inviscid turbine aerodynamic computer codes and loss models used at the NASA Lewis Research Center is presented. Five flow situations are examined, for which both experimental data and computational results are available. The five flows form a basis for the evaluation of the computational procedures. It was concluded that stator flows may be calculated with a high degree of accuracy, whereas, rotor flow fields are less accurately determined. Exploitation of contouring, leaning, bowing, and sweeping will require a three dimensional viscous analysis technique.

Povinelli, L. A.↗

NASA NTRS1985

Analytical modeling of circuit aerodynamics in the new NASA Lewis wind tunnel

Rehabilitation and extention of the capability of the altitude wind tunnel (AWT) was analyzed. The analytical modeling program involves the use of advanced axisymmetric and three dimensional viscous analyses to compute the flow through the various AWT components. Results for the analytical modeling of the high speed leg aerodynamics are presented; these include: an evaluation of the flow quality at the entrance to the test section, an investigation of the effects of test section bleed for different model blockages, and an examination of three dimensional effects in the diffuser due to reentry flow and due to the change in cross sectional shape of the exhaust scoop.

Towne, C. E.↗

NASA NTRS1985

Analytical and physical modeling program for the NASA Lewis Research Center's Altitude Wind Tunnel (AWT)

An effort is currently underway at the NASA Lewis Research Center to rehabilitate and extend the capabilities of the Altitude Wind Tunnel (AWT). This extended capability will include a maximum test section Mach number of about 0.9 at an altitude of 55,000 ft and a -20 F stagnation temperature (octagonal test section, 20 ft across the flats). In addition, the AWT will include an icing and acoustic research capability. In order to insure a technically sound design, an AWT modeling program (both analytical and physical) was initiated to provide essential input to the AWT final design process. This paper describes the modeling program, including the rationale and criteria used in program definition, and presents some early program results.

Abbott, J. M.↗

NASA NTRS1985

Analytical and physical modeling program for the NASA Lewis Research Center's Altitude Wind Tunnel (AWT)

Abbott, J. M.↗

NASA NTRS1985

Analytical modeling of circuit aerodynamics in the new NASA Lewis Altitude Wind Tunnel

Rehabilitation and extention of the capability of the altitude wind tunnel (AWT) was analyzed. The analytical modelling program involves the use of advanced axisymmetric and three dimensional viscous analyses to compute the flow through the various AWT components. Results for the analytical modelling of the high speed leg aerodynamics are presented; these include: an evaluation of the flow quality at the entrance to the test section, an investigation of the effects of test section bleed for different model blockages, and an examination of three dimensional effects in the diffuser due to reentry flow and due to the change in cross sectional shape of the exhaust scoop.

Towne, C. E.↗

NASA NTRS1984

Application of a quasi-3D inviscid flow and boundary layer analysis to the hub-shroud contouring of a radial turbine

Application of a quasi-3D approach to the aerodynamic analysis of several radial turbine configurations is described. The objective was to improve the rotor aerodynamic characteristics by hub-shroud contouring. The approach relies on available 2D inviscid methods coupled with boundary layer analysis to calculate profile, mixing, and endwall losses. Windage, tip clearance, incidence, and secondary flow losses are estimated from correlations. To eliminate separation along the hub and blade suction surfaces of a baseline rotor, the analysis was also applied to three alternate hub-shroud geometries. Emphasis was on elimination of an inducer velocity overshoot as well as increasing hub velocities. While separation was never eliminated, the extent of the separated area was progressively reduced. Results are presented in terms of mid-channel and blade surface velocities; kinetic energy loss coefficients; and efficiency. The calculation demonstrates a first step for a systematic approach to radial turbine design that can be used to identify and control aerodynamic characteristics that ultimately determine heat transfer and component life. Experimentation will be required to assess the extent to which flow and boundary layer behavior were predicted correctly.

Civinskas, K.↗

NASA NTRS1984

Investigation of mixing in a turbofan exhaust duct. II Computer code application and verification

A three-dimensional analysis of turbofan forced mixer nozzle aerodynamics demonstrates that the complex flow structure is dominated by geometrically induced secondary flow rather than by turbulence. The test apparatus consisted of a fixed upstream model section and a rotating shroud. The Mach number of the fan and core streams at the mixing plane (lobe exit) was 0.45, the bypass ratio was about 4, and the Reynolds number based on the shroud radius was 1,100,000. The three velocity components near the exit plane of the lobes were measured using flow angularity probes to provide information about the mixer inflow conditions for turbulent computations. The validity of a previous computer code was demonstrated in a comparison of the nozzle exit temperature data with the computed temperature distributions. The mechanism most responsible for the generation of secondary flow within the lobes is due to the turning of the fan and core streams in opposite radial directions.

Povinelli, L. A.↗

NASA NTRS1984

Assessment of three-dimensional inviscid codes and loss calculations for turbine aerodynamic computations

An assessment of several three dimensional inviscid turbine aerodynamic computer codes and loss models used at the NASA Lewis Research Center is presented. Five flow situations are examined, for which both experimental data and computational results are available. The five flows form a basis for the evaluation of the computational procedures. It was concluded that stator flows may be calculated with a high degree of accuracy, whereas, rotor flow fields are less accurately determined. Exploitation of contouring, learning, bowing, and sweeping will require a three dimensional viscous analysis technique.

Povinelli, L. A.↗

NASA NTRS1984

Comparison of secondary flows predicted by a viscous code and an inviscid code with experimental data for a turning duct

A comparison of the secondary flows computed by the viscous Kreskovsky-Briley-McDonald code and the inviscid Denton code with benchmark experimental data for turning duct is presented. The viscous code is a fully parabolized space-marching Navier-Stokes solver while the inviscid code is a time-marching Euler solver. The experimental data were collected by Taylor, Whitelaw, and Yianneskis with a laser Doppler velocimeter system in a 90 deg turning duct of square cross-section. The agreement between the viscous and inviscid computations was generally very good for the streamwise primary velocity and the radial secondary velocity, except at the walls, where slip conditions were specified for the inviscid code. The agreement between both the computations and the experimental data was not as close, especially at the 60.0 deg and 77.5 deg angular positions within the duct. This disagreement was attributed to incomplete modelling of the vortex development near the suction surface.

Schwab, J. R.↗

NASA NTRS1984

Hot-flow tests of a series of 10-percent-scale turbofan forced mixing nozzles

An approximately 1/10-scale model of a mixed-flow exhaust system was tested in a static facility with fully simulated hot-flow cruise and takeoff conditions. Nine mixer geometries with 12 to 24 lobes were tested. The areas of the core and fan stream were held constant to maintain a bypass ratio of approximately 5. The research results presented in this report were obtained as part of a program directed toward developing an improved mixer design methodology by using a combined analytical and experimental approach. The effects of lobe spacing, lobe penetration, lobe-to-centerbody gap, lobe contour, and scalloping of the radial side walls were investigated. Test measurements included total pressure and temperature surveys, flow angularity surveys, and wall and centerbody surface static pressure measurements. Contour plots at various stations in the mixing region are presented to show the mixing effectiveness for the various lobe geometries.

Head, V. L.↗

NASA NTRS1984

Application of a quasi-3D inviscid flow and boundary layer analysis to the hub-shroud contouring of a radial turbine

Application of a quasi-3D approach to the aerodynamic analysis of several radial turbine configurations is described. The objective was to improve the rotor aerodynamic characteristics by hub-shroud contouring. The approach relies on available 2D inviscid methods coupled with boundary layer analysis to calculate profile, mixing, and endwall losses. Windage, tip clearance, incidence, and secondary flow losses are estimated from correlations. To eliminate separation along the hub and blade suction surfaces of a baseline rotor, the analysis was also applied to three alternate hub-shroud geometries. Emphasis was on elimination an inducer velocity overshoot as well as increasing hub velocities. While separation was never eliminated, the extent of the separated area was progressively reduced. Results are presented in terms of mid-channel and blade surface velocities; kinetic energy loss coefficients; and efficiency. The calculation demonstrates a first step for a systematic approach to radial turbine design that can be used to identify and control aerodynamic characteristics that ultimately determine heat transfer and component life. Experimentation will be required to assess the extent to which flow and boundary layer behavior were predicted correctly.

Civinskas, K. C.↗

NASA NTRS1984

Application of viscous and inviscid computation methods for rocket turbopump systems

This paper examines current research efforts underway at Lewis Research Center which have focused on improving the structural durability of the SSME turbodrive system through more fully examining the aerothermodynamics of the flow system. This objective was achieved by developing three-dimensional viscous and inviscid computer codes to predict the pressure and temperature distributions in the engine flow passages, particularly within the SSME turbines and turnaround ducts.

Povinelli, L. A.↗

NASA NTRS1983

Comparison of secondary flows predicted by a viscous code and an inviscid code with experimental data for a turning duct

A comparison of the secondary flows computed by the viscous Kreskovsky-Briley-McDonald code and the inviscid Denton code with benchmark experimental data for turning duct is presented. The viscous code is a fully parabolized space-marching Navier-Stokes solver while the inviscid code is a time-marching Euler solver. The experimental data were collected by Taylor, Whitelaw, and Yianneskis with a laser Doppler velocimeter system in a 90 deg turning duct of square cross-section. The agreement between the viscous and inviscid computations was generally very good for the streamwise primary velocity and the radial secondary velocity, except at the walls, where slip conditions were specified for the inviscid code. The agreement between both the computations and the experimental data was not as close, especially at the 60.0 deg and 77.5 deg angular positions within the duct. This disagreement was attributed to incomplete modeling of the vortex development near the suction surface.

Schwab, J. R.↗

NASA NTRS1981

Factors which influence the behavior of turbofan forced mixer nozzles

A finite difference procedure was used to compute the mixing for three experimentally tested mixer geometries. Good agreement was obtained between analysis and experiment when the mechanisms responsible for secondary flow generation were properly modeled. Vorticity generation due to flow turning and vorticity generated within the centerbody lobe passage were found to be important. Results are presented for two different temperature ratios between fan and core streams and for two different free stream turbulence levels. It was concluded that the dominant mechanisms in turbofan mixers is associated with the secondary flows arising within the lobe region and their development within the mixing section.

Anderson, B. H.↗

NASA NTRS1981

Factors which influence the behavior of turbofan forced mixer nozzles

A finite difference procedure was used to compute the mixing for three experimentally tested mixer geometries. Good agreement was obtained between analysis and experiment when the mechanisms responsible for secondary flow generation were properly modeled. Vorticity generation due to flow turning and vorticity generated within the centerbody-lobe passage were found to be important. Results are presented for two different temperature ratios between fan and core streams and for two different free-stream turbulence levels. It was concluded that the dominant mechanisms in turbofan mixers is associated with the secondary flows arising within the lobe region and their development within the mixing section.

Anderson, B. H.↗

NASA NTRS1980

An analytical and experimental study of a short s-shaped subsonic diffuser of a supersonic inlet

A subscale HiMAT forebody and inlet was investigated over a range of Mach numbers to 1.4. The inlet exhibited a transitory separation within the diffuser but steady state data indicated reattachment at the diffuser exit. A finite difference procedure for turbulent compressible flow in axisymmetric ducts was used to successfully model the HiMAT duct flow. The analysis technique was further used to estimate the initiation of separation and delineate the steady and unsteady flow regimes in similar S-shaped ducts.

Neumann, H. E.↗

NASA NTRS1980

Computation of three-dimensional flow in turbofan mixers and comparison with experimental data

A three dimensional, viscous computer code was used to calculate the mixing downstream of a typical turbofan mixer geometry. Experimental data obtained using pressure and temperature rakes at the lobe and nozzle exit stations were used to validate the computer results. The relative importance of turbulence in the mixing phenomenon as compared with the streamwise vorticity set up by the secondary flows was determined. The observations suggest that the generation of streamwise vorticity plays a significant role in determining the temperature distribution at the nozzle exit plane.

Povinelli, L. A.↗

NASA NTRS1980

Computation of three-dimensional flow in turbofan mixers and comparison with experimental data

A three-dimensional, viscous computer code was used to calculate the mixing downstream of a typical turbofan mixer geometry. Experimental data were obtained using pressure and temperature rakes at the lobe and nozzle exit stations. Secondary flow velocities were also obtained. These data were used to validate the computer results. An assessment was also made to determine the relative importance of turbulence in the mixing phenomenon as compared with the streamwise vorticity set up by the secondary flows. The observations suggest that the generation of streamwise vorticity appears to play a significant role in determining the temperature distribution at the nozzle exit plane.

Povinelli, L. A.↗