Engineering Papers⌕ Search

Engineering topics

Patel, P

Publications and source records attributed to Patel, P.

30 records · Page 2

Size Scaling of Tensile Failure Stress in a Soda-Lime-Silicate Float Glass

The (tensile) strength-size scaling of a float soda-lime silicate glass was studied using biaxial flexure and Hertzian ring crack initiation testing. The examined Weibull effective areas spanned ~ 0.4 to 48,000 mm2. Both the air- and tin-sides were tested. The air side was stronger than the tin side as others have observed; however, the differences in their characteristic strengths decreased with decreasing effective area, and their strengths converged for effective areas smaller than ~ 100 mm2. The failure stress at the smallest effective area examined for the tin-side was ~ 500% greater than that at the largest effective area while that difference was ~ 250% for the air- side. A Weibull modulus change at ~ 100 mm2 suggests different strength-limiting flaw types were dominant below and above that effective area. These results reinforce the importance to interpret and use tensile strength of glass in context to how much of its area is being tensile stressed.

36 MATERIALS SCIENCE↗

Features of a point design for fast ignition

Fast Ignition is an inertial fusion scheme in which fuel is first assembled and then heated to the ignition temperature with an external heating source. In this note we consider cone and shell implosions where the energy supplied by short pulse lasers is transported to the fuel by electrons. We describe possible failure modes for this scheme and how to overcome them. In particular, we describe two sources of cone tip failure, an axis jet driven from the compressed fuel mass and hard photon preheat leaking through the implosion shell, and laser prepulse that can change the position of laser absorption and the angular distribution of the emitted electrons.

42 ENGINEERING↗

Mitigation of Electromagnetic Pulse (EMP) Effects from Short-Pulse Lasers and Fusion Neutrons

Our research focused on obtaining a fundamental understanding of the source and properties of EMP at the Titan PW(petawatt)-class laser facility. The project was motivated by data loss and damage to components due to EMP, which can limit diagnostic techniques that can be used reliably at short-pulse PW-class laser facilities. Our measurements of the electromagnetic fields, using a variety of probes, provide information on the strength, time duration, and frequency dependence of the EMP. We measure electric field strengths in the 100's of kV/m range, durations up to 100 ns, and very broad frequency response extending out to 5 GHz and possibly beyond. This information is being used to design shielding to mitigate the effects of EMP on components at various laser facilities. We showed the need for well-shielded cables and oscilloscopes to obtain high quality data. Significant work was invested in data analysis techniques to process this data. This work is now being transferred to data analysis procedures for the EMP diagnostics being fielded on the National Ignition Facility (NIF). In addition to electromagnetic field measurements, we measured the spatial and energy distribution of electrons escaping from targets. This information is used as input into the 3D electromagnetic code, EMSolve, which calculates time dependent electromagnetic fields. The simulation results compare reasonably well with data for both the strength and broad frequency bandwidth of the EMP. This modeling work required significant improvements in EMSolve to model the fields in the Titan chamber generated by electrons escaping the target. During dedicated Titan shots, we studied the effects of varying laser energy, target size, and pulse duration on EMP properties. We also studied the effect of surrounding the target with a thick conducting sphere and cube as a potential mitigation approach. System generated EMP (SGEMP) in coaxial cables does not appear to be a significant at Titan. Our results are directly relevant to planned short-pulse ARC (advanced radiographic capability) operation on NIF.

36 MATERIALS SCIENCE↗

Physical and optoelectronic characterization of reactively sputtered molybdenum-silicon-nitride alloy metal gate electrodes

With continued transistor scaling, work function tuning of metal gates has become important for advanced complementary-metal-oxide-silicon applications. The work function tuning of reactively sputtered Mo{sub x}Si{sub y}N{sub z} (also referred to as MoSiN) gates has been studied through the incorporation of nitrogen. The nitrogen concentration in the MoSiN films was altered by controlling the gas flow ratio, R{sub N}=N{sub 2}/(N{sub 2}+Ar), during gate deposition. The sheet resistance (R{sub s}) of blanket MoSiN films, measured using four-point resistance method, was found to increase as the gas flow ratio was varied from 10% to 40%. Current-voltage measurements confirmed excellent electrical stability of MoSiN/SiO{sub 2}/p-Si gate stack for applied electric fields ranging up to 6 MV/cm. High frequency capacitance-voltage measurements were used to extract the MoSiN work function ({phi}{sub m}) using the relationship between the flatband voltage (V{sub FB}) and the oxide thickness (t{sub ox}). The extracted MoSiN/SiO{sub 2} interfacial barrier heights, obtained through the internal photoemission of electrons, were used to corroborate the extracted values of MoSiN work function. The MoSiN work functions ({phi}{sub m}), extracted independently using both techniques, were consistent and were observed to decrease with increasing gas flow ratio [N{sub 2}/(N{sub 2}+Ar)]. Secondary ion mass spectrometry depth analysis revealed uniform distribution of nitrogen throughout the bulk MoSiN films, with no piling up at gate-dielectric interface. X-ray photoelectron spectroscopy surface analysis suggested a steady increase in the Mo-N bonds, and therefore the total nitrogen concentration (from {approx}20% to 32%), as the gas flow ratio is increased from 10% to 40%. A similar trend was observed in the nitrogen concentration (in percent), measured using Rutherford backscattering spectroscopy, for these gate deposition conditions. These material characterization results demonstrate that the increase in nitrogen concentration in MoSiN films is consistent with the lowering of MoSiN work function. Moreover, the work function of reactively sputtered Mo{sub x}Si{sub y}N{sub z} films was found to be variable over {approx}0.3 eV by adjusting the nitrogen concentration.

36 MATERIALS SCIENCE↗

A Bremsstrahlung spectrometer using k-edge and differential filters with image plate dosimeters

A Bremsstrahlung spectrometer using k-edge and differential filtering has been used with image plate dosimeters to measure the x-ray fluence from short-pulse laser/target interactions. An electron spectrometer in front of the Bremsstrahlung spectrometer deflects electrons from the x-ray line of sight and simultaneously measures the electron spectrum. The response functions were modeled with the Monte Carlo code INTEGRATED TIGER SERIES 3.0 and the dosimeters calibrated with radioactive sources. An electron distribution with a slope temperature of 1.3 MeV is inferred from the Bremsstrahlung spectra.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Electron heated target temperature measurements in petawatt laser experiments based on extreme ultraviolet imaging and spectroscopy

Three independent methods (extreme ultraviolet spectroscopy, imaging at 68 and 256 eV) have been used to measure planar target rear surface plasma temperature due to heating by hot electrons. The hot electrons are produced by ultraintense laser-plasma interactions using the 150 J, 0.5 ps Titan laser. Soft x-ray spectroscopy in the 50-400 eV region and imaging at the 68 and 256 eV photon energies give a planar deuterated carbon target rear surface pre-expansion temperature in the 125-150 eV range, with the rear plasma plume averaging a temperature approximately 74 eV.

07 ISOTOPE AND RADIATION SOURCES↗

HOT ELECTRON ENERGY DISTRIBUTIONS FROM ULTRA-INTENSE LASER SOLID INTERACTIONS

Measurements of electron energy distributions from ultra-intense (>10{sup 19} W/cm{sup 2}) laser-solid interactions using an electron spectrometer are presented. These measurements were performed on the Vulcan petawatt laser at Rutherford Appleton Laboratory and the Callisto laser at Lawrence Livermore National Laboratory. The effective hot electron temperatures (T{sub hot}) have been measured for laser intensities (I{lambda}{sup 2}) from 10{sup 18} W/cm{sup 2} {micro}m{sup 2} to 10{sup 21} W/cm{sup 2} {micro}m{sup 2} for the first time, and T{sub hot} is found to increase as (I{lambda}{sup 2}){sup 0.34} {+-} 0.4. This scaling agrees well with the empirical scaling published by Beg et al. (1997), and is explained by a simple physical model that gives good agreement with experimental results and particle-in-cell simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation of Collisionless Shocks in Laser-Plasma Experiments

The propagation in a rarefied plasma (n{sub e} < or approx. 10{sup 15} cm{sup -3}) of collisionless shock waves and ion-acoustic solitons, excited following the interaction of a long ({tau}{sub L}{approx}470 ps) and intense (I{approx}10{sup 15} W cm{sup -2}) laser pulse with solid targets, has been investigated via proton probing techniques. The shocks' structures and related electric field distributions were reconstructed with high spatial and temporal resolution. The experimental results were interpreted within the framework of the nonlinear wave description based on the Korteweg-de Vries-Burgers equation.

43 PARTICLE ACCELERATORS↗

Hard x-ray radiography for density measurement in shock compressed matter

In this letter we report on the direct density measurement in a shock compressed aluminum target using hard x-ray radiography. Experimental data employing a molybdenum K{alpha} source at 17.5 keV, generated with a short pulse laser are presented. High spatial resolution was obtained thanks to a new design for the backlighter geometry. Density values deduced from radiography are compared to predictions from hydrodynamic simulations, which have been calibrated in order to reproduce shock velocities measured from a rear-side self-emission diagnostic. Our results reveal the great potential of this technique as a diagnostic tool for direct density measurements in dense high-Z opaque materials.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

High performance compact magnetic spectrometers for energetic ion and electron measurement in ultra intense short pulse laser solid interactions

Ultra intense short pulse lasers incident on solid targets can generate relativistic electrons that then accelerate energetic protons and ions. These fast electrons and ions can effectively heat the solid target, beyond the region of direct laser interaction, and are vital to realizing the fast ignition concept. To study these energetic ions and electrons produced from the laser-target interactions, we have developed a range of spectrometers that can cover a large energy range (from less than 0.1 MeV to above 100 MeV). They are physically compact and feature high performance and low cost. We will present the basic design of these spectrometers and their test results from recent laser experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Diagnostics for Fast Ignition Science

The concept for Electron Fast Ignition Inertial Confinement Fusion demands sufficient laser energy be transferred from the ignitor pulse to the assembled fuel core via {approx}MeV electrons. We have assembled a suite of diagnostics to characterize such transfer. Recent experiments have simultaneously fielded absolutely calibrated extreme ultraviolet multilayer imagers at 68 and 256eV; spherically bent crystal imagers at 4 and 8keV; multi-keV crystal spectrometers; MeV x-ray bremmstrahlung and electron and proton spectrometers (along the same line of sight); nuclear activation samples and a picosecond optical probe based interferometer. These diagnostics allow careful measurement of energy transport and deposition during and following laser-plasma interactions at extremely high intensities in both planar and conical targets. Augmented with accurate on-shot laser focal spot and pre-pulse characterization, these measurements are yielding new insight into energy coupling and are providing critical data for validating numerical PIC and hybrid PIC simulation codes in an area that is crucial for many applications, particularly fast ignition. Novel aspects of these diagnostics and how they are combined to extract quantitative data on ultra high intensity laser plasma interactions are discussed, together with implications for full-scale fast ignition experiments.

42 ENGINEERING↗