Engineering topics

Outlaw, R. A.

Publications and source records attributed to Outlaw, R. A..

At least 19 records

NASA NTRS1994

Thermal desorption of CO and H2 from degassed 304 and 347 stainless steel

Thermal desorption spectroscopy (TDS), along with Auger electron spectroscopy, was used to study the desorption of H2 and CO from baked 304 and 347 stainless-steel samples exposed only to residual gases. Both 347 and 304 samples gave identical TDS spectra. The spectra for CO contained a sharp leading peak centered in the temperature range 410-440C and an exponentially increasing part for temperatures higher than 500C, with a small peak around 600C appearing as a shoulder. The leading peak followed a second-order desorption behavior with an activation energy of 28+/-2 kcal/mol, suggesting that the rate-limiting step for this peak is most likely a surface reaction that produces the CO molecules in the surface layer. The amount of desorbed CO corresponding to this peak was approximately 0.5X10(exp 14) molecules/cm(exp 2) . The exponentially rising part of the CO spectrum appeared to originate from a bulk diffusion process. The TDS spectrum for H2 consisted of a main peak centered also in the temperature range 410-440C, with two small peaks appearing as shoulders at approximately 500 and 650C. The main peak in this case also displayed a second-order behavior with an activation energy of 14+/-2 kcal/mol. The amount of desorbed H2, approximately 1.9X 10(exp 15) molecules/cm(exp 2) , appeared to be independent of the concentration of hydrogen in the bulk, indicating that the majority of the desorbed H2 originated from the surface layer.

Rezaie-Serej, S.↗

NASA NTRS1994

A study of glow-discharge and permeation techniques for extraterrestrial oxygen beneficiation

Extraction of oxygen from Martian atmosphere and compression of lunar oxygen can utilize stabilized zirconia electrochemical pumps. Silver membranes can be used as electrodes to increase oxygen yield at relatively low temperatures. This study has investigated oxygen permeation through Ag 0.05Zr membranes with glow-discharge assisted disassociation. Data show that the overall process is controlled by bulk diffusion but the slow dissociative adsorption onto the surface limited the overall transport substantially. With glow-discharge assisted dissociation, an order of magnitude increase in oxygen throughput can be produced at relatively low temperatures (450-550C).

Ash, R. L.↗

NASA NTRS1994

Small ultrahigh vacuum compatible hyperthermal oxygen atom generator

The development of a compact, ultrahigh vacuum (UHV) compatible instrument for generating a flux of pure hyperthermal oxygen atoms for NASA applications has been achieved. The instrument combines the mechanisms of O2 dissociation and transport through a hot Ag membrane to provide a continuous source of O atoms to a vacuum interface where they are subsequently emitted into the vacuum space by electron-stimulated desorption (ESD). A flux of neutral O atoms 4.5 X 10(exp 13) cm(exp-2) s(exp-l)(P-3) with a mean ion kinetic energy of approximately 5eV and a full width at half maximum of 4eV was detected at a quadrupole mass spectrometer located 10 cm away. The geometry of the instrument is such that it is mounted on a 7 cm flange and can be tailored in length and orientation to fit most UHV systems. The data presented here are for ESD-controlled conditions where increases in the flux are strictly linear with electron bombardment current. Calculation shows that transport-controlled conditions can be achieved at temperatures as low as 350 C with membrane thicknesses on the order of 10 micron.

Outlaw, R. A.↗

NASA NTRS1993

Surface compositional variations of Mo-47Re alloy as a function of temperature

Molybdenum-rhenium alloys are candidate materials for the National Aero-Space Plane (NASP) as well as for other applications in generic hypersonics. These materials are expected to be subjected to high-temperature (above 1200 C) casual hydrogen (below 50 torr), which could potentially degrade the material strength. Since the uptake of hydrogen may be controlled by the contaminant surface barriers, a study of Mo-47Re was conducted to examine the variations in surface composition as a function of temperature from 25 C to 1000 C. Pure molybdenum and rhenium were also examined and the results compared with those for the alloy. The analytical techniques employed were Auger electron spectroscopy, electron energy loss spectroscopy, ion scattering spectroscopy, and x ray photoelectron spectroscopy. The native surface was rich in metallic oxides that disappeared at elevated temperatures. As the temperature increased, the carbon and oxygen disappeared by 800 C and the surface was subsequently populated by the segregation of silicon, presumably from the grain boundaries. The alloy readily chemisorbed oxygen, which disappeared with heating. The disappearance temperature progressively increased for successive dosings. When the alloy was exposed to 800 torr of hydrogen at 900 C for 1 hour, no hydrogen interaction was observed.

Hoekje, S. J.↗

NASA NTRS1993

Hydrogen transport behavior of Timetal-21S alloy

Use is made of the thermogravimetric-analysis method to ascertain the hydrogen-transport characteristics of the Timetal-21S beta-Ti alloy, at pressures of up to 50 torr over the 400-800 C temperature range. Hydrogen solubility is found to be high; the equilibrium hydrogen concentration is noted to deviate from Sievert's law at higher pressures. These deviations are likely associated with hydrogen-induced microstructural changes in the alloy, and the kinetics of hydrogen uptake reflect these changes.

Sankaran, Sankara N.↗

NASA NTRS1993

Hyperthermal-Atomic-Oxygen Generator

Small hyperthermal-atomic-oxygen generator (HAOG) compatible with ultrahigh vacuum (UHV) developed. Provides pure flux of ground-state oxygen atoms with mean kinetic energy of approximately 5 eV, accurately simulating conditions in low orbit around Earth, and mounted on any existing UHV processing or analysis system. HAOG clean and compatible with other UHV processing or diagnostic systems and relatively inexpensive and simple to operate. Valuable in studies involving atomic oxygen because added easily to existing systems.

Outlaw, R. A.↗

NASA NTRS1993

Generation of O2 From CO2 by Glow Discharge And Permeation

Technique for generating supply of highly pure O2 from CO2 developed. First, atomic oxygen at useful partial pressure generated by glow-discharge dissociation of CO2. Atomic oxygen formed in vicinity of hot silver membrane and permeates through membrane to downstream region, where thermally recombined into O2 and pumped away to storage tank. Pure oxygen stored suitable for human consumption and other uses. Originally developed to convert Martian atmosphere of CO2 to O2 for astronaut consumption. Other potential applications include purification of atmospheres in Space Shuttle and Space Station Freedom. Byproduct CO must be handled by other techniques.

Outlaw, R. A.↗

NASA NTRS1992

Study of the oxygen transport through Ag (110), Ag (poly), and Ag 2.0 Zr

The transport of oxygen through high-purity membranes of Ag (110), Ag (poly), Ag (nano), and Ag 2.0 Zr has been studied by an ultrahigh vacuum permeation method over the temperature range of 400-800 C. The data show that there are substantial deviations from ordinary diffusion-controlled transport. A surface limitation has been confirmed by glow-discharge studies where the upstream O2 supply has been partially converted to atoms, which, for the same temperature and pressure, gave rise to over an order of magnitude increase in transport flux. Further, the addition of 2.0 wt percent Zr to the Ag has provided increased dissociative adsorption rates, which, in turn, increased the transport flux by a factor of 2. It was also observed that below a temperature of 630 C, the diffusivity exhibits an increase in activation energy of over 4 kcal/mol, which has been attributed to trapping of the atomic oxygen and/or kinetic barriers at the surface and subsurface of the vacuum interface. Above 630 C, the activation barrier decreases to the accepted value of about 11 kcal/mol for Ag (poly), consistent with zero concentration at the vacuum interface.

Outlaw, R. A.↗

NASA NTRS1991

Titanium aluminides - Surface composition effects as a function of temperature

Results are presented from an AES investigation of the surface characteristics of pure Ti, Ti-14Al-21Nb (alpha-2 aluminide), and Ti-33Al-6Nb-1.4Ta (gamma aluminide) under ultrahigh vacuum conditions over the 20-1000 C temperature range. The observed variations in surface composition are noted to be dramatic and indicative of a direct relationship between the amount of retained oxygen and carbon on the surface and the quantity of Al in that surface's vicinity. While TiO2 was the main surface oxide for pure Ti and the alpha-2 and gamma aluminides, only metallic peaks were observable at 600 C; at 1000 C, metallic Al and Ti were observed.

Outlaw, R. A.↗

NASA NTRS1991

Auger electron intensity variations in oxygen-charged silver

Auger intensity variations over an oxygen-charged polycrystalline silver surface have been observed by studies of Auger images and line scans of selected adjacent grains which were determined to be the (421) and (221) orientations. The observed contrast (M4.5VV transition) between the grains is produced by the variation in the detected Auger electrons caused by the different directions (interatomic direction) of forward focusing in each grain. The contrast produced by the Ag Auger electrons was found to be strongly dependent on the surface order of the grains, but that of the O Auger electrons was not, presumably because the atoms were randomly distributed throughout the Ag surface or subsurface. The contrast observed between the grains at the lower Auger energies (N1VV and N1N2.3V transitions) appeared to be produced by constructive interference from multiple scattering. The N1N2.3V electrons at 29 eV, for example, gave higher contrast than that of the N1VV transition at 78 eV.

Lee, W. S.↗

NASA NTRS1990

O2 and CO2 glow-discharge-assisted oxygen transport through Ag

Experiments were conducted to determine whether dissociative adsorption is a possible limitation of the oxygen permeability through Ag, using the upstream glow-discharge dissociation of O2 and CO2 to provide a gas phase source of atomic oxygen. Results suggest that the dissociative adsorption step limits the supply of oxygen atoms to the upstream side of the membrane. When the upstream O2 was replaced by an equal pressure of CO2 in absence of glow discharge, only a small permeation signal was observed; the application of the glow discharge increasded the oxygen transport flux from 3.25 x 10 to the 12th/sq cm per sec to 1.74 x 10 to the 14th/sq cm per sec. It is suggested that this method of separating O2 from a CO2-rich atmosphere may be considered for providing oxygen for the astronauts in a manned expedition to Mars.

Outlaw, R. A.↗

NASA NTRS1990

The surface variation of Ti-14Al-21Nb as a function of temperature under ultrahigh vacuum conditions

The effect of temperature, at conditions of ultrahigh vacuum, on the surface composition of the Ti-14Al-21Nb (in wt pct) alloy was investigated in samples heated to 1000 C in 100 C increments. Results of AES spectroscopy revealed that the Ti-14Al-21Nb alloy surface is extremely sensitive to temperature. At 300 C, the carbon and oxygen began to rapidly dissolve into the alloy, and at 600 C, bulk S segregated to the surface. The variation in the surface composition was extensive and different over the temperature range studied, indicating that there may be substantial changes in the hydrogen transport.

Lee, W. S.↗

NASA NTRS1990

An Auger electron spectroscopy study of surface-preparation contaminants

There are many cleaning techniques that are presently being employed for surface preparation of materials that are subsequently exposed to ultrahigh vacuum (UHV). Unfortunately, there are virtually no comparative measurements which establish the residual contaminant level of each method. In this report, eleven different cleaning methods, ranging from only detergent cleaning to electrochemical polishing, were applied to identical samples of 347 stainless steel. Two surface conditions, a standard machined surface and a mechanically polished surface, were studied. Auger electron spectroscopy (AES) within a UHV environment was then used to detect the types of contaminants and the magnitudes found on the sample surfaces. It was found that the electrochemical polishing gave the least contaminated surface of all metals studied and that mechanically polished surfaces were significantly cleaner than the as-machined surfaces for any given cleaning method. Furthermore, it was also found that the residual contaminations left by methanol, ethanol, isopropyl alcohol, acetone, and freon finishing rinses are almost the same.

Wu, D.↗

NASA NTRS1989

Introduction to total- and partial-pressure measurements in vacuum systems

An introduction to the fundamentals of total and partial pressure measurement in the vacuum regime (760 x 10 to the -16th power Torr) is presented. The instrument most often used in scientific fields requiring vacuum measurement are discussed with special emphasis on ionization type gauges and quadrupole mass spectrometers. Some attention is also given to potential errors in measurement as well as calibration techniques.

Outlaw, R. A.↗

NASA NTRS1989

Continuous electron stimulated desorption using a ZrO2/Ag permeation membrane

During the development of an atomic oxygen beam generator for laboratory simulation of the atmospheric conditions in low earth orbit, a new technique for performing electron stimulated desorption (ESD) in a continuous manner has been developed. In this technique, oxygen permeates through an Ag membrane at elevated temperature thereby providing a continuous supply of oxygen atoms to the 1000-A ZrO2 coating at the vacuum interface. ESD then results in a large peak of neutral O2 molecules which ultimately decay into steady-state desorption. The ESD signal is linear with respect to primary beam flux (0.035 O2 molecules per electron at a primary beam energy of 1 keV) but nonlinear with respect to primary beam energy.

Outlaw, R. A.↗

NASA NTRS1989

Auger electron intensity variations in oxygen-exposed large grain polycrystalline silver

Auger electron spectroscopic studies of the grains in oxygen-charged polycrystal-line silver show significant intensity variations as a function of crystallographic orientation. These intensity variations were observed by studies of the Auger images and line scans of the different grains (randomly selected) for each silver transition energy. The results can be attributed to the diffraction of the ejected Auger electrons and interpreted by corresponding changes in the electron mean-free path for inelastic scattering and by oxygen atom accumulation in the subsurface. The subsurface (second layer) octahedral sites increased in size because of surface relaxation and serve as a stable reservoir for the dissolved oxygen.

Lee, W. S.↗

NASA NTRS1988

Oxygen transport through high-purity, large-grain Ag

The permeability of oxygen through pure, large-grain Ag membrames has been found to be linear and repeatable over the 400-800 C range, but only at a magnitude that is a factor of 3.2 smaller than ascribed by prior research. AES data indicate the pertinence of grain-boundary considerations, due to the virtual undetectability of intragranular oxygen. Vacuum-desorption of oxygen-saturated Ag is found to occur at the critical temperature of 630 C; this is consistent with the increased mobility of oxygen atoms in the higher temperature regime.

Outlaw, R. A.↗

NASA NTRS1988

Atomic forces between noble gas atoms, alkali ions, and halogen ions for surface interactions

The components of the physical forces between noble gas atoms, alkali ions, and halogen ions are analyzed and a data base developed from analysis of the two-body potential data, the alkali-halide molecular data, and the noble gas crystal and salt crystal data. A satisfactory global fit to this molecular and crystal data is then reproduced by the model to within several percent. Surface potentials are evaluated for noble gas atoms on noble gas surfaces and salt crystal surfaces with surface tension neglected. Within this context, the noble gas surface potentials on noble gas and salt crystals are considered to be accurate to within several percent.

Wilson, J. W.↗