Engineering Papers⌕ Search

Engineering topics

Moseley, S. H.

Publications and source records attributed to Moseley, S. H..

At least 73 records · Page 4

Parameter Comparison for Low-Noise MoAu TES Bolometers

We describe a comparative investigation of the parameters of MoAu-bilayer Transition Edge Sensor (TES) bolometers designed for infrared detectors. A set of devices with variations in geometry were fabricated at the NASA/GSFC detector development facility. These detectors have different bilayer aspect ratios (providing differing normal state resistances and current densities), and have varieties of normal metal regions to study the effects of geometry on noise. These normal metal regions are oriented either parallel to or transverse to the direction of current flow, or both. The lowest noise detectors are found to have normal metal regions oriented transversely. For about a dozen different devices, we have measured a large set of parameters by means of a suite of tests. These include complex impedance measurements to derive time constants; IV curves to determine resistance and power; thermal conductance measurements; noise measurements as a function of device resistance; and &rect resistance vs. temperature measurements .

Benford, D. J.↗

The Single Aperture Far-Infrared (SAFIR) Observatory and its Cryogenic Detector Needs

The development of a large, far-infrared telescope in space has taken on a new urgency with breakthroughs in detector technology and recognition of the fundamental importance of the far-infrared spectral region to questions ranging from cosmology to our own Solar System. The Single Aperture Far-InfraRed (SAFIR) Observatory is l0m-class far-infrared observatory that would begin development later in this decade to meet these needs. SAFIR's science goals are driven by the fact that youngest stages of almost all phenomena in the universe are shrouded in absorption by and emission from cool dust that emits strongly in the far-infrared, 20 microns - 1mm. Its operating temperature (4 K) and instrument complement would be optimized to reach the natural sky confusion limit in the far-infrared with diffraction-limited performance down to at least the atmospheric cutoff at 40 microns. This would provide a point source sensitivity improvement of several orders of magnitude over that of SIRTF. In order to achieve this, large arrays of detectors with NEPs ranging from a few to a hundred zeptowatts/sqrt(Hz) are needed. Very low temperature superconducting transition edge sensors and far-infrared "photon counting" detectors are critical technologies requiring development for the SAFIR mission.

Benford, Dominic J.↗

Optimal Fitting of Non-linear Detector Pulses with Nonstationary Noise

Optimal extraction of pulses of constant known shape from a time series with stationary noise is well understood and widely used in detection applications. Applications where high resolution is required over a wide range of input signal amplitudes use much of the dynamic range of the sensor. The noise will in general vary over this signal range, and the response may be a nonlinear function of the energy input. We present an optimal least squares procedure for inferring input energy in such a detector with nonstationary noise and nonlinear energy response.

Fixsen, D. J.↗

Broadband Direct Detection Submillimeter Spectrometer with Multiplexed Superconducting Transition Edge Thermometer Bolometers

We present performance results based on the first astronomical use of multiplexed superconducting bolometers as direct detectors (i.e., with cold electrons) for spectroscopy. The Fabry-Perot Interferometer Bolometer Research Experiment (FIBRE) is a broadband submillimeter spectrometer for the Caltech Submillimeter Observatory (CSO). FIBRE's detectors are superconducting transition edge sensor (TES) bolometers read out by a SQUID multiplexer. The Fabry-Perot uses a low resolution grating to order sort the incoming light. A linear bolometer array consisting of 16 elements detects this dispersed light, capturing 5 orders simultaneously from one position on the sky. With tuning of the Fabry-Perot over one free spectral range, a spectrum covering Delta lambda/lambda = 1/7 at a resolution of delta lambda/lambda = 1/1200 can be acquired. This spectral resolution is sufficient to resolve Doppler-broadened line emission from external galaxies. FIBRE has been operated in the 350 Am (850 GHz) band. These bands cover line emission from the important star formation tracers neutral carbon [CI] and carbon monoxide (CO).

Benford, D. J.↗

Submillimeter and Far Infrared Experiment for SOFIA (SAFIRE): Progress and Prospects

SAFIRE/SOFIA is a versatile imaging Fabry-Perot spectrograph covering 100 less than lambda less than 655 microns, with spectral resolving power of approx. l0(exp 3). Selected as a "PI" instrument for the airborne Stratospheric Observatory for Infrared Astronomy (SOFIA), SAFIRE will apply two dimensional pop-up bolometer arrays to provide background limited imaging spectrometry. We describe the instrument design, its application to a range of astro- physical investigations, and current progress and results in the innovative detector and instrument design. SAFIRE/SOFIA is on track for availability in 2006.

Shafer, R. A.↗

SAFIRE: A Far-Infrared Imaging Spectrometer for SOFIA

The SOFIA airborne observatory will provide a high spatial resolution, low background telescope for far-infrared astrophysical investigations. Selected as a PI instrument for SOFIA, SAFIRE is an imaging Fabry-Perot spectrograph covering 145 micrometers-655 micrometers with spectral resolving power of approx. 1500 (200km/s). This resolution is well matched to extragalactic emission lines and yields the greatest sensitivity for line detection. SAFIRE will make important scientific contributions to the study of the powering of ULIRGs and AGN, the role of CII cooling in extragalactic star formation, the evolution of matter in the early Universe, and the energetics of the Galactic center. SAFIRE will employ a two-dimensional pop-up bolometer array to provide background-limited imaging spectrometry. Superconducting transition edge bolometers and SQUID amplifiers have been developed for these detectors. An engineering prototype of SAFIRE with a small but cutting edge detector array will be available for use during the initial SOFIA operations; further expansion to larger format arrays will be incorporated during SAFIRE's lifetime.

Shafer, Richard A.↗

Arrays of Bolometric Detectors for Submillimeter Astronomy

Large format two dimensional arrays of bolometric detectors are required for many millimeter and submillimeter applications. We describe the development and testing of such arrays and the plans for using them in both a ground-based and airborne instrument.

Silverberg, R. F.↗

First Astronomical Use Of Multiplexed Transition Edge Bolometers

We present performance results based on the first astronomical use of multiplexed superconducting bolometers. The Fabry-Perot Interferometer Bolometer Research Experiment (FIBRE) is a broadband submillimeter spectrometer that achieved first light in June 2001 at the Caltech Submillimeter Observatory (CSO). FIBRE's detectors are superconducting transition edge sensor (TES) bolometers read out by a SQUID multiplexer. The Fabry-Perot uses a low resolution grating to order sort the incoming light. A linear bolometer array consisting of 16 elements detects this dispersed light, capturing five orders simultaneously from one position on the sky. With tuning of the Fabry-Perot over one free spectral range, a spectrum covering delta-lamda/lamda = 1/7 at a resolution of delta-lamda/lamda = 1/1200 can be acquired. This spectral resolution is sufficient to resolve doppler broadened line emission from external galaxies. FIBRE operates in the 350 micrometer and 450 micrometer bands. These bands cover line emission from the important PDR tracers neutral carbon [CI] and carbon monoxide (CO). We have verified that the multiplexed bolometers are photon noise limited even with the low power present in moderate resolution spectrometry.

Benford, D. J.↗

Ecological Niches for Space Missions in the Far-Infrared

The far-infrared and submillimeter region (30 micrometers-750 micrometers) has perhaps the greatest potential of all wavelengths for advancement in astronomy. When viewed in terms of the cosmic backgrounds, the fares is extremely important: half of the total luminosity in the Universe is emitted at rest wavelengths approximately 80 - 100 micrometers. At the highest known galaxy redshifts (z approximately equal to 6) this energy is redshifted to approximately 600 micrometers. Existing and planned survey missions have a broad range of capabilities, defined in terms of their spectral coverage, spectral resolution, survey area, and sensitivity. In this 4-dimensional parameter space, the flares is found to be substantially behind most other wavelength bands. The opportunity for future missions with great discovery potential is evident. Such missions will be wellsuited to answering fundamental questions about the history of energy release in the Universe, the formation and evolution of galaxies, and formation of stellar and protoplanetary systems. We discuss the parameter space that can be filled by a few well-chosen space missions, specifically a submillimeter all-sky survey and a far-IR to submillimeter observatory.

Benford, Dominic J.↗

Far-Infrared Imaging Spectroscopy with SAFIRE on SOFIA

The SOFIA airborne observatory will provide a high spatial resolution, low background telescope for far-infrared astrophysical investigations. Selected as a PI instrument for SOFIA, SAFIRE is an imaging Fabry-Perot spectrograph covering 100 micrometers - 655 micrometers, with spectral resolving power of approx. 1500 (200 kilometers per second). This resolution is well matched to extragalactic emission lines and yields the greatest sensitivity for line detection. SAFIRE will make important scientific contributions to the study of the powering of ULIRGs and AGN, the role of CII cooling in extragalactic star formation, the evolution of matter in the early Universe, and the energetics of the Galactic center. SAFIRE will employ a two-dimensional pop-up barometer array in a 16 x 32 format to provide background-limited imaging spectrometry. Superconducting transition edge barometers and SQUID amplifiers have been developed for these detectors.

Shafer, Richard A.↗

Morphology, near-infrared luminosity, and mass of the Galactic bulge from COBE DIRBE observations

Near-infrared images of the Galactic bulge at 1.25, 2.2, 3.5, and 4.9 microns obtained by the Diffuse Infrared Background Experiment (DIRBE) onboard the Cosmic Background Explorer (COBE) satellite are used to characterize its morphology and to determine its infrared luminosity and mass. Earlier analysis of the DIRBE observations (Weiland et al. 1994) provided supporting evidence for the claim made by Blitz & Spergel (1991) that the bulge is bar-shaped with its near end in the first Galactic quadrant. Adopting various triaxial analytical functions to represent the volume emissivity of the source, we confirm the barlike nature of the bulge and show that triaxial Gaussian-type functions provide a better fit to the data than other classes of functions, including an axisymmetric spheroid. The introduction of a `boxy' geometry, such as the one used by Kent, Dame, & Fazio (1991) improves the fit to the data. Our results show that the bar is rotated in the plane with its near side in the first Galactic quadrant creating an angle of 20 deg +/- 10 deg between its major axis and the line of sight to the Galactic center. Typical axis ratios of the bar are (1:0.33 +/- 0.11:0.23 +/- 0.08), resembling the geometry of prolate spheroids. There is no statistically significant evidence for an out-of-plane tilt of the bar at 2.2 microns, and marginal evidence for a tilt of approximately equal 2 deg at 4.9 microns. The introduction of a roll around the intrinsic major axis of the bulge improves the `boxy' appearance of some functions. A simple integration of the observed projected intensity of the bulge gives a bulge luminosity of 1.2 x 10(exp 9), 4.1 x 10(exp 8), 2.3 x 10(exp 8), and 4.3 x 10(exp 7) solar luminosity, respectively, at 1.25, 2.2, 3.5, and 4.9 microns wavelength for a Galactocentric distance of 8.5 kpc. The 2.2 microns luminosity function of the bulge population in the direction of Baade's window yields a bolometric luminosity of L(sub bol) = 5.3 x 10(exp 9) solar luminosity. Stellar evolutionary models relate this luminosity to the number of main-sequence progenitor stars that currently populate the red giant branch. Combined with the recent determination of the main-sequence turnoff mass for the bulge by the Hubble Space Telescope (Holtzman et al. 1993) we derive a photometrically determined bulge mass of approximately equal to 1.3 x 10(exp 10) solar mass for a Salpeter initial mass function extended down to 0.1 solar mass.

Dwek, E.↗

Morphology of the interstellar cooling lines detected by COBE

The Far-Infrared Absolute Spectrophotometer (FIRAS) on the COBE satellite has conducted an unbiased survey of the far-infrared emission from our Galaxy. The first results of this survey were reported by Wright et al. (1991). We report the results of new analyses of this spectral survey, which includes emission lines from 158 micrometer C(+), 122 and 205 micrometer N(+), 370 and 609 micrometer C(0), and CO J = 2 goes to 1 through J = 5 goes to 4. We report the morphological distribution along the Galactic plane (b = 0 deg) of the spectral line emission, and the high Galactic latitude intensities of the C(+) and 205 micrometer N(+) emission. In the Galactic plane the 205 micrometer line of N(+) generally follows the 158 micrometer C(+) line distribution, but the intensities scale as I(N(+) 205 micrometer) varies as I(C(+) 158 micrometer)(exp 1.5) toward the inner Galaxy. The high Galactic latitude intensity of the 158 micrometer fine-structure transition from C(+) is I(C(+) 158 micrometer) = (1.43 +/- 0.12) x 10(exp -6) csc (absolute value of b) ergs/sq cm s sr for absolute value of b greater than 15 deg, and it decreases more rapidly than the far-infrared intensity with increasing Galactic latitude. C(+) and neutral atomic hydrogen emission are closely correlated with a C(+) cooling rate of (2.65 +/- 0.15) x 10(exp -26) ergs/s. We conclude that this emission arises almost entirely from the cold neutral medium. The high Galactic latitude intensity of the 205 micrometer fine-structure transition from N(+) is I(N(+) 205 micrometer) = (4 +/- 1) x 10(exp -8) csc (absolute value of b) ergs/((sq cm)(s)(sr)) arising entirely from the warm ionized medium. We estimate the total ionizing photon rate in the Galaxy to be phi = 3.5 x 10(exp 53) ionizing photons per second, based on the 205 micrometer N(+) transition.

Bennett, C. L.↗

Infrared observations of Comet Austin (1990 V) by the COBE/Diffuse Infrared Background Experiment

Comet Austin was observed by the Cosmic Background Explorer (COBE)/Diffuse Infrared Background Experiment (DIRBE) with broadband photometry at 1-240 micrometers during the comet's close passage by Earth in 1990 May. A 6 deg long (6 x 10(exp 6) km) dust tail was found at 12 and 25 micrometers, with detailed structure due to variations in particle properties and mass-loss rate. The spectrum of the central 42 x 42 sq arcmin pixel was found to agree with that of a graybody of temperature 309 +/- 5 K and optical depth 7.3 +/- 10(exp -8). Comparison with IUE and ground-based obervations indicates that particles of radius greater than 20 micrometers predominate by surface area. A mass-loss rate of 510 (+510/-205) kg/s and a total tail mass of 7 +/- 2 x 10(exp 10) kg was found for a model dust tail composed of Mie spheres with a differential particle mass distribution dn/d log m approx. m(exp -0.63) and 2:1 silicate:amorphous carbon composition by mass.

Lisse, C. M.↗

COBE DIRBE near-infrared polarimetry of the zodiacal light: Initial results

This Letter describes near-infrared polarimetry of the zodiacal light at 2.2 micrometers, measured with the Diffuse Infrared Background Experiment (DIRBE) aboard the Cosmic Background Explorer (COBE) spacecraft. The polarization is due to scattering of sunlight. The polarization vector is perpendicular to the scattering plane, and its observed amplitude on the ecliptic equator at an elongation of 90 deg and ecliptic longitude of 10 deg declines from 12.0 +/- 0.4% at 1.25 micrometers to 8.0 +/- 0.6% at 3.5 micrometers (cf. 16% in the visible); the principal source of uncertainty is photometric noise due to stars. The observed near-infrared colors at this location are redder than Solar, but at 3.5 micrometers this is due at least in part to the thermal emission contribution from the interplanetary dust. Mie theory calculations show that both polarizations and colors are important in constraining models of interplanetary dust.

Berriman, G. B.↗

Dirbe evidence for a wrap in the interstellar dust layer and stellar disk of the galaxy

The Diffuse Infrared Background Experiment (DIRBE) of the Cosmic Background Explorer (COBE) has mapped the surface brightness distributions of the Galactic plane at wavelengths from 1.25 to 240 micrometers. In these maps the latitude of peak brightness, as a function of longitude, traces a roughly sinusoidal curve of period approximately 360 deg. In the far-infrared, where emission by interstellar dust dominates the surface brightness, this curve agrees well with that derived from maps of the velocity-integrated H 1, suggesting that the layers of dust and neutral atomic hydrogen are similarly displaced from the Galactic plane. In the near-infrared (lambda less than 5 micrometers), where old disk stars dominate the emission, the brightness crest exhibits the same phase but roughly half the amplitude. The reduced amplitude of the warp in stellar light could result from a lesser warping of the stellar disk, or from a more rapid falloff of the density of stars relative to the density of gas, possibly due to a radial truncation of the disk.

Freudenreich, H. T.↗

Large-scale characteristics of interstellar dust from COBE DIRBE observations

Observations from the COBE Diffuse Infrared Background Experiment of the 140 and 240 micrometer emissions from the Galatic plane region (absolute value of b less than 10 deg) are combined with radio surveys that trace the molecular (H2), neutral atomic (H I), and extended low-density (n(sub e) approximately 10 to 100/cm(exp 3)) ionized (H II) gas phases of the interstellar medium to derive physical conditions such as the dust temperature, dust-to-gas mass ratio, and far-infrared emissivity (1) averaged over these gas phases along each line of sight and (2) within each of these three gas phases. This analysis shows large-scale longitudinal and latitudinal gradients in the dust temperature and a decrease in dust temperature with increasing Galactocentric distance. The derived dust temperatures are significantly different from those derived in similar analyses using the Infrared Astronomical Satellite (IRAS) 60 and 100 micrometer data, suggesting that small (5 A approximately less than radius approximately less than 200 A) transiently heated dust particles contribute significantly o the Galactic 60 micrometer emission. It is found that 60% to 75% of the far-infrared luminosity arises from cold (approximately 17 to 22 K) dust associated with diffuse H I clouds, 15% to 30% from cold (approximately 19 K) dust associated with molecular gas, and less than 10% from warm (approximately 29 K) dust in extended low-density H II regions, consistent with the results of the IRAS analyses of the Galactic 60 and 100 micrometer emission. Within 2 deg of longitude of the Galactic center, the derived gas-to-dust mass ratio along the line of sight, G(sub d), reverses its general trend of decreasing G(sub d) toward the inner Galaxy and increases by a factor of approximately 2 to 3 toward the Galactic center. One possible explanation for this result is that the ratio of H2 column density to (12)CO intensity is lower in the Galactic center region than in the Galactic disk.

Sodroski, T. J.↗

COBE diffuse infrared background experiment observations of the galactic bulge

Low angular resolution maps of the Galactic bulge at 1.25, 2.2, 3.5, and 4.9 micrometers obtained by the Diffuse Infrared Background Experiment (DIRBE) onboard NASA's Cosmic Background Explorer (COBE) are presented. After correction for extinction and subtraction of an empirical model for the Galactic disk, the surface brightness distribution of the bulge resembles a flattened ellipse with a minor-to-major axis ratio of approximately 0.6. The bulge minor axis scale height is found to be 2.1 deg +/- 0.2 deg for all four near-infrared wavelengths. Asymmetries in the longitudinal distribution of bulge brightness contours are qualitatively consistent with those expected for a triaxial bar with its near end in the first Galactic quadrant (0 deg less than l less than 90 deg). There is no evidence for an out-of-plane tilt of such a bar.

Weiland, J. L.↗

COBE diffuse infrared background experiment observations of Galactic reddening and stellar populations

This Letter describes the results of an initial study of Galactic extinction and the colors of Galactic stellar populations in the near-IR using the Diffuse Infrared Background Experiment (DIRBE) aboard the Cosmic Background Explorer (COBE) spacecraft. The near-IR reddening observed by DIRBE is consistent with the extinction law tabulated by Rieke & Lebofsky (1985). The distribution of dust and stars in most of the first and fourth quadrants of the Galactic plane (0 deg less than l less than 90 deg, and 270 deg less than l less than 360 deg, respectively) can be modeled as a stellar background source seen through up to approximately 4 mag of extinction at 1.25 micrometers. The unreddened near-IR colors of the Galactic disk are similar to those of late-K and M giants. The Galactic bulge exhibits slightly bluer colors in the 2.2-3.5 micrometers range, as noted by Terndrup et al. (1991). Star-forming regions exhibit colors that indicate the presence of a approximately 900 K continuum produced by hot dust or polycyclic aromatic hydrocarbons (PAHs) contributing at wavelengths as short as 3.5 micrometers.

Arendt, R. G.↗