Engineering Papers⌕ Search

Engineering topics

Moghaddam, Mahta

Publications and source records attributed to Moghaddam, Mahta.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Demonstrating a New Flood Observing Strategy on the Nos Testbed

A new observing strategy for floods was demonstrated and evaluated in a testbed environment. The strategy coordinates several observing platforms, including in situ and space based, to observe a flood from multiple vantage points and to dynamically target predicted flood events with high- resolution observations. The coordinated observations were assimilated back into the model to improve forecasts and future observation selection. This demonstration shows the potential for coordinated, model-driven observing strategies and the feasibility of the NOS Testbed for demonstrating and evaluating new observing strategies.

Capra, Leigha↗
NASA NTRS2021

Potential of Full-polarimetric P- and L-band Sar Data in Characterizing Post-fire Recovery of Arctic Tundra

We used the airborne full polarimetric L-band and P-band SAR (PolSAR) data collected from recent NASA ABoVE Arctic Boreal Vulnerability Experiment (ABoVE) airborne campaign to understand the sensitivity of longwave radar backscatter intensity and phase to post-fire recovery process of Arctic tundra. The 2007 Anaktuvuk River fire was used as a case study. At 10-year post-fire, we observed a strong increase (>~4 dB) in both the P- and L-band radar backscatter in the severely burned areas, in contrast to limited backscatter differences (VV, VH) between burned and unburned areas at C-band. The polarimetric target decomposition analysis indicated a general trend towards more random surface scattering, and strong increases of the double-bounce and volumetric scattering power at both P- and L-band in the burned areas. Large differences were also observed in the Pauli phase angle and the dominant-scattering-type Touzi phase angle between the burned and unburned areas. The above changes are likely caused by increasing surface roughness and microtopography due to thermokarst development and ice degradation, and increasing subsurface scattering due to an overall drier and deeper active layer in the burned areas

Miller, Charles E.↗
NASA NTRS2020

Joint retrieval of soil moisture and permafrost active layer thickness using L-band InSAR and P-band PolSAR

Seasonal subsidence measured by repeat-pass interferometric synthetic aperture radar (InSAR) can be used to infer the active layer thickness (ALT) in permafrost regions. The differential volume of soil water undergoing the phase change over the thaw season is one of the factors impacting the seasonal subsidence and is a function of both soil moisture profile and thaw depth. Without the information about soil moisture, this InSAR approach can have large biases in the ALT estimates when soil moisture profile is below saturation. Soil moisture and ALT can also be estimated from polarimetric synthetic aperture radar (PolSAR) backscatter observations but the sensing depth of the PolSAR approach is limited when deep ALT is present. In this paper, we integrated these two approaches and applied a joint retrieval method to estimate the soil moisture profiles and ALT from the L-band InSAR and P-band PolSAR data acquired over the Arctic-boreal region during the 2017 Arctic-Boreal Vulnerability Experiment (ABoVE) airborne campaign.

Schaefer, Kevin M.↗
NASA NTRS2020

Mapping tree canopy cover and canopy height with L-band SAR using LiDAR data and Random Forests

Light detection and ranging (LiDAR) data can provide direct measurements of vegetation structures but are limited by the sparse spatial coverage. Polarimetric synthetic aperture radar (SAR) can perform large-scale high-resolution mapping without weather constraints but the information about vegetation and ground subsurface are mixed in the backscatter data. In this paper, we adopted the Random Forests algorithm to train an upscaling function using tree canopy cover (TCC) and canopy height model (CHM) derived from Goddard’s LiDAR, Hyperspectral and Thermal Imager (G-LiHT) data. The regression model is then applied to the L-band Uninhabited Aerial Vehicle Synthetic Aperture Radar (UAVSAR) data acquired during the 2017 Arctic-Boreal Vulnerability Experiment (ABoVE) airborne campaign to map the TCC and CHM over the Delta Junction area in interior Alaska.

Moghaddam, Mahta↗
NASA NTRS2019

Developing a soil inversion model framework for regional permafrost monitoring

Currently, the community lacks capabilities to assess and monitor landscape scale permafrost active layer dynamics over large extents. To address this need, we developed a concept of a remote sensing based Soil Inversion Model for regional Permafrost (SIM-P) monitoring. The current SIM-P framework includes a satellite-based soil process model and a soil dielectric model. We are also working on incorporating a radar scattering model for Arctic tundra into the SIM-P framework. A unified soil parameterization scheme was developed to harmonize key soil thermal, hydraulic and dielectric parameters in the soil process and radar models that can be used in the joint soil-radar inversion framework. The soil parameter retrievals of the SIM-P framework include soil organic content (SOC) and active layer thickness (ALT). Initial tests of SIM-P using in-situ soil permittivity observations showed reasonable accuracy in predicting site-level SOC and soil temperature profiles at an Alaska tundra site and ALT in Arctic Alaska. SIM-P will be further tested using airborne P- and L-band radar data collected during NASA’s Arctic Boreal Vulnerability Experiment (ABoVE) to evaluate the sensitivity of longwave radar to active layer properties.

Miller, Charles E.↗
NASA NTRS2018

The SMAP Mission Combined Active-Passive Soil Moisture Product at 9 Km and 3 Km Spatial Resolutions

The NASA Soil Moisture Active Passive (SMAP) mission was launched on January 31st, 2015. The spacecraft was to provide high-resolution (3 km and 9 km) global soil moisture estimates at regular intervals by combining for the first time L-band radiometer and radar observations. On July 7th, 2015, a component of the SMAP radar failed and the radar ceased operation. However, before this occurred the mission was able to collect and process ~2.5 months of the SMAP high-resolution active-passive soil moisture data (L2SMAP) that coincided with the Northern Hemisphere's vegetation green-up and crop growth season. In this study, we evaluate the SMAP high-resolution soil moisture product derived from several alternative algorithms against in situ data from core calibration and validation sites (CVS), and sparse networks. The baseline algorithm had the best comparison statistics against the CVS and sparse networks. The overall unbiased root-mean-square-difference is close to the 0.04 cu. m/cu. m the SMAP mission requirement. A 3 km spatial resolution soil moisture product was also examined. This product had an unbiased root-mean-square-difference of ~0.053 cu. m/cu. m. The SMAP L2SMAP product for ~2.5 months is now validated for use in geophysical applications and research and available to the public through the NASA Distributed Active Archive Center (DAAC) at the National Snow and Ice Data Center (NSIDC). The L2SMAP product is packaged with the geo-coordinates, acquisition times, and all requisite ancillary information. Although limited in duration, SMAP has clearly demonstrated the potential of using a combined L-band radar-radiometer for proving high spatial resolution and accurate global soil moisture.

high resolution soil moisture↗
NASA NTRS2013

UAVSAR Program: Initial Results from New Instrument Capabilities

UAVSAR is an imaging radar instrument suite that serves as NASA's airborne facility instrument to acquire scientific data for Principal Investigators as well as a radar test-bed for new radar observation techniques and radar technology demonstration. Since commencing operational science observations in January 2009, the compact, reconfigurable, pod-based radar has been acquiring L-band fully polarimetric SAR (POLSAR) data with repeat-pass interferometric (RPI) observations underneath NASA Dryden's Gulfstream-III jet to provide measurements for science investigations in solid earth and cryospheric studies, vegetation mapping and land use classification, archaeological research, soil moisture mapping, geology and cold land processes. In the past year, we have made significant upgrades to add new instrument capabilities and new platform options to accommodate the increasing demand for UAVSAR to support scientific campaigns to measure subsurface soil moisture, acquire data in the polar regions, and for algorithm development, verification, and cross-calibration with other airborne/spaceborne instruments.

P-band polarimetry↗
NASA NTRS2011

NASA's Earth Venture-1 (EV-1) Airborne Science Investigations

In 2010, NASA announced the first Earth Venture (EV-1) selections in response to a recommendation made by the National Research Council for low-cost investigations fostering innovation in Earth science. The five EV-1 investigations span the Earth science focus areas of atmosphere, weather, climate, water and energy and, carbon and represent earth science researchers from NASA as well as other government agencies, academia and industry from around the world. The EV-1 missions are: 1) Airborne Microwave Observatory of Subcanopy and Subsurface (AirMOSS), 2) Airborne Tropical Tropopause Experiment (ATTREX), 3) Carbon in Arctic Reservoirs Vulnerability Experiment (CARVE), 4) Deriving Information on Surface Conditions from Column and Vertically Resolved Observations Relevant to Air Quality (DISCOVER-AQ), and 5) Hurricane And Severe Storm Sentinel (HS3). The Earth Venture missions are managed out of the Earth System Science Pathfinder (ESSP) Program Office (Allen, et. al. 2010b)

Guillory, A.↗
NASA NTRS2009

The Soil Moisture Active and Passive (SMAP) Mission

The Soil Moisture Active and Passive (SMAP) Mission is one of the first Earth observation satellites being developed by NASA in response to the National Research Council s Decadal Survey. SMAP will make global measurements of the moisture present at Earth's land surface and will distinguish frozen from thawed land surfaces. Direct observations of soil moisture and freeze/thaw state from space will allow significantly improved estimates of water, energy and carbon transfers between land and atmosphere. Soil moisture measurements are also of great importance in assessing flooding and monitoring drought. SMAP observations can help mitigate these natural hazards, resulting in potentially great economic and social benefits. SMAP soil moisture and freeze/thaw timing observations will also reduce a major uncertainty in quantifying the global carbon balance by helping to resolve an apparent missing carbon sink on land over the boreal latitudes. The SMAP mission concept would utilize an L-band radar and radiometer. These instruments will share a rotating 6-meter mesh reflector antenna to provide high-resolution and high-accuracy global maps of soil moisture and freeze/thaw state every two to three days. The SMAP instruments provide direct measurements of surface conditions. In addition, the SMAP project will use these observations with advanced modeling and data assimilation to provide deeper root-zone soil moisture and estimates of land surface-atmosphere exchanges of water, energy and carbon. SMAP is scheduled for a 2014 launch date

Entekhabi, Dara↗
NASA NTRS2005

Single-Chip FPGA Azimuth Pre-Filter for SAR

A field-programmable gate array (FPGA) on a single lightweight, low-power integrated-circuit chip has been developed to implement an azimuth pre-filter (AzPF) for a synthetic-aperture radar (SAR) system. The AzPF is needed to enable more efficient use of data-transmission and data-processing resources: In broad terms, the AzPF reduces the volume of SAR data by effectively reducing the azimuth resolution, without loss of range resolution, during times when end users are willing to accept lower azimuth resolution as the price of rapid access to SAR imagery. The data-reduction factor is selectable at a decimation factor, M, of 2, 4, 8, 16, or 32 so that users can trade resolution against processing and transmission delays. In principle, azimuth filtering could be performed in the frequency domain by use of fast-Fourier-transform processors. However, in the AzPF, azimuth filtering is performed in the time domain by use of finite-impulse-response filters. The reason for choosing the time-domain approach over the frequency-domain approach is that the time-domain approach demands less memory and a lower memory-access rate. The AzPF operates on the raw digitized SAR data. The AzPF includes a digital in-phase/quadrature (I/Q) demodulator. In general, an I/Q demodulator effects a complex down-conversion of its input signal followed by low-pass filtering, which eliminates undesired sidebands. In the AzPF case, the I/Q demodulator takes offset video range echo data to the complex baseband domain, ensuring preservation of signal phase through the azimuth pre-filtering process. In general, in an SAR I/Q demodulator, the intermediate frequency (fI) is chosen to be a quarter of the range-sampling frequency and the pulse-repetition frequency (fPR) is chosen to be a multiple of fI. The AzPF also includes a polyphase spatial-domain pre-filter comprising four weighted integrate-and-dump filters with programmable decimation factors and overlapping phases. To prevent aliasing of signals, the bandwidth of the AzPF is made 80 percent of fPR/M. The choice of four as the number of overlapping phases is justified by prior research in which it was shown that a filter of length 4M can effect an acceptable transfer function. The figure depicts prototype hardware comprising the AzPF and ancillary electronic circuits. The hardware was found to satisfy performance requirements in real-time tests at a sampling rate of 100 MHz.

Gudim, Mimi↗
NASA NTRS2005

A Tower-based Prototype VHF/UHF Radar for Subsurface Sensing: System Description and Data Inversion Results

Knowledge of subsurface characteristics such as permittivity variations and layering structure could provide a breakthrough in many terrestrial and planetary science disciplines. For Earth science, knowledge of subsurface and subcanopy soil moisture layers can enable the estimation of vertical flow in the soil column linking surface hydrologic processes with that in the subsurface. For planetary science, determining the existence of subsurface water and ice is regarded as one of the most critical information needs for the study of the origins of the solar system. The subsurface in general can be described as several near-parallel layers with rough interfaces. Each homogenous rough layer can be defined by its average thickness, permittivity, and rms interface roughness assuming a known surface spectral distribution. As the number and depth of layers increase, the number of measurements needed to invert for the layer unknowns also increases, and deeper penetration capability would be required. To nondestructively calculate the characteristics of the rough layers, a multifrequency polarimetric radar backscattering approach can be used. One such system is that we have developed for data prototyping of the Microwave Observatory of Subcanopy and Subsurface (MOSS) mission concept. A tower-mounted radar makes backscattering measurements at VHF, UHF, and L-band frequencies. The radar is a pulsed CW system, which uses the same wideband antenna to transmit and receive the signals at all three frequencies. To focus the beam at various incidence angles within the beamwidth of the antenna, the tower is moved vertically and measurements made at each position. The signals are coherently summed to achieve focusing and image formation in the subsurface. This requires an estimate of wave velocity profiles. To solve the inverse scattering problem for subsurface velocity profile simultaneously with radar focusing, we use an iterative technique based on a forward numerical solution of the layered rough surface problem. The layers are each defined in terms of a small number of unknown distributions as given above. An a priori estimate of the solution is first assumed, based on which the forward problem is solved for the backscattered measurements. This is compared with the measured data and using iterative techniques an update to the solution for the unknowns is calculated. The process continues until convergence is achieved. Numerical results will be shown using actual radar data acquired with the MOSS tower radar system in Arizona in Fall 2003, and compared with in-situ measurements.

Moghaddam, Mahta↗
NASA NTRS2004

Radar for Measuring Soil Moisture Under Vegetation

A two-frequency, polarimetric, spaceborne synthetic-aperture radar (SAR) system has been proposed for measuring the moisture content of soil as a function of depth, even in the presence of overlying vegetation. These measurements are needed because data on soil moisture under vegetation canopies are not available now and are necessary for completing mathematical models of global energy and water balance with major implications for global variations in weather and climate.

Moghaddam, Mahta↗
NASA NTRS2000

Effect of Medium Symmetries in Limiting the Number of Parameters Estimated with Polarimetric Interferometry

The addition of interferometric backscattering pairs to the conventional polarimetric SAR data over forests and other vegetated areas increases the dimensionality of the data space, in principle enabling the estimation of a larger number of vegetation parameters. Without regard to the sensitivity of these data to vegetation scattering parameters, this paper poses the question: Will increasing the data channels as such result in a one-to-one increase in the number of parameters that can be estimated, or do vegetation and data properties inherently limit that number otherwise? In this paper, the complete polarimetric interferometric covariance matrix is considered and various symmetry properties of the scattering medium are used to study whether any of the correlation pairs can be eliminated. The number of independent pairs has direct consequences in their utility in parameter estimation schemes, since the maximum number of parameters that can be estimated cannot exceed the number of unique measurements. The independent components of the polarimetric interferometric SAR (POL/INSAR) data are derived for media with reflection, rotation, and azimuth symmetries, which are often encountered in vegetated surfaces. Similar derivations have been carried out before for simple polarimetry, i.e., zero baseline. This paper extends those to the interferometric case of general nonzero baselines. It is shown that depending on the type of symmetries present, the number of independent available measurements that can be used to estimate medium parameters will vary. In particular, whereas in the general case there are 27 mathematically independent measurements possible from a polarimetric interferometer, this number can be reduced to 15, 9, and 6 if the medium has reflection, rotation, or azimuthal symmetries, respectively. The results can be used in several ways in the interpretation of SAR data and the development of parameter estimation schemes, which will be discussed at the presentation. Recent POL/INSAR data from the JPL AIRSAR over a forested area will be used to demonstrate the results of this derivation. This work was performed by the Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, under contract from the National Aeronautics and Space Administration.

Moghaddam, Mahta↗
NASA NTRS2000

Fusion of AIRSAR and TM Data for Parameter Classification and Estimation in Dense and Hilly Forests

The expanded remotely sensed data space consisting of coincident radar backscatter and optical reflectance data provides for a more complete description of the Earth surface. This is especially useful where many parameters are needed to describe a certain scene, such as in the presence of dense and complex-structured vegetation or where there is considerable underlying topography. The goal of this paper is to use a combination of radar and optical data to develop a methodology for parameter classification for dense and hilly forests, and further, class-specific parameter estimation. The area to be used in this study is the H. J. Andrews Forest in Oregon, one of the Long-Term Ecological Research (LTER) sites in the US. This area consists of various dense old-growth conifer stands, and contains significant topographic relief. The Andrews forest has been the subject of many ecological studies over several decades, resulting in an abundance of ground measurements. Recently, biomass and leaf-area index (LAI) values for approximately 30 reference stands have also become available which span a large range of those parameters. The remote sensing data types to be used are the C-, L-, and P-band polarimetric radar data from the JPL airborne SAR (AIRSAR), the C-band single-polarization data from the JPL topographic SAR (TOPSAR), and the Thematic Mapper (TM) data from Landsat, all acquired in late April 1998. The total number of useful independent data channels from the AIRSAR is 15 (three frequencies, each with three unique polarizations and amplitude and phase of the like-polarized correlation), from the TOPSAR is 2 (amplitude and phase of the interferometric correlation), and from the TM is 6 (the thermal band is not used). The range pixel spacing of the AIRSAR is 3.3m for C- and L-bands and 6.6m for P-band. The TOPSAR pixel spacing is 10m, and the TM pixel size is 30m. To achieve parameter classification, first a number of parameters are defined which are of interest to ecologists for forest process modeling. These parameters include total biomass, leaf biomass, LAI, and tree height. The remote sensing data from radar and TM are used to formulate a multivariate analysis problem given the ground measurements of the parameters. Each class of each parameter is defined by a probability density function (pdf), the spread of which defines the range of that class. High classification accuracy results from situations in which little overlap occurs between pdfs. Classification results provide the basis for the future work of class-specific parameter estimation using radar and optical data. This work was performed in part by the Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, and in part by the NASA Ames Research Center, Moffett Field, CA, both under contract from the National Aeronautics and Space Administration.

Moghaddam, Mahta↗