Engineering Papers⌕ Search

Engineering topics

Miller, D. S.

Publications and source records attributed to Miller, D. S..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Impact of fuselage incidence on the supersonic aerodynamics of two fighter configurations

The results of experimental and theoretical investigations into the effect of fuselage upwash on fighter aircraft wing performance are reported. Wind tunnel trials were performed on 4 percent scale models of two supersonic fighters. The trials were run at Mach 1.6-2.0, an Re of 2,000,000 and at angles of attack (AOA) of -4 to 20 deg. Measurements were made of lift, drag and pitching moments. Two linearized theory supersonic aerodynamic prediction codes, PAN AIR and the SDAS lift analysis, were used to predict the same aerodynamic coefficients. The fuselage AOA augmented the lift and pitching moment at 0, 2 and 5 deg. The contribution mainly arose from the fuselage-induced upwash. The PAN AIR code gave superior data for the fuselage aerodynamics and effects, although both codes accurately predicted the overall lift and moment increments due to the fuselage AOA.

Wood, R. M.↗
NASA NTRS1984

Assessment of preliminary prediction techniques for wing leading-edge vortex flows at supersonic speeds

The applicability of existing theoretical models for predicting wing leading edge separated flow characteristics for high-lift supersonic flight was examined with regard to previous experimental force, pressure and flow visualization data. Correlations of data on uncambered delta wings revealed that the upper surface normal force and minimum pressure coefficients decreased nonlinearly with increasing angles of attack. The attainable vacuum pressure decreased with increasing Mach number, while the lower surface normal force increased nonlinearly with increasing speed. The LISTAR and VORCAM linear theory aerodynamic codes generated predictions for comparison with the data. LISTAR displayed better agreement with measured vortex strength and position and lifting characteristics than did VORCAM. The Euler code SWINT was ill-suited to calculating wing performance in separated flows at high lift and low supersonic speeds.

Wood, R. M.↗
NASA NTRS1984

Supersonic, nonlinear, attached-flow wing design for high lift with experimental validation

Results of the experimental validation are presented for the three dimensional cambered wing which was designed to achieve attached supercritical cross flow for lifting conditions typical of supersonic maneuver. The design point was a lift coefficient of 0.4 at Mach 1.62 and 12 deg angle of attack. Results from the nonlinear full potential method are presented to show the validity of the design process along with results from linear theory codes. Longitudinal force and moment data and static pressure data were obtained in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.58, 1.62, 1.66, 1.70, and 2.00 over an angle of attack range of 0 to 14 deg at a Reynolds number of 2.0 x 10 to the 6th power per foot. Oil flow photographs of the upper surface were obtained at M = 1.62 for alpha approx. = 8, 10, 12, and 14 deg.

Pittman, J. L.↗
NASA NTRS1984

Effect of fuselage upwash on the supersonic longitudinal aerodynamic characteristics of 2 fighter configurations

An experimental and theoretical investigation of fuselage incidence effects on two fighter aircraft models, which differed in wing planform only, has been conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.6, 1.8, and 2.0. Results were obtained on the two models at fuselage incidence angles of 0 deg, 2 deg, and 5 deg. The fuselage geometry included two side-mounted, flow-through, half-axisymmetric inlets and twin vertical tails. The two planforms tested were cranked wings with 70 deg/66 deg and 70 deg/30 deg leading-edge sweep angles. Experimental data showed that fuselage incidence resulted in positive increments in configuration lift and pitching moment; most of the lift increment can be attributed to the fuselage-induced upwash acting on the wing and most of the pitching-moment increment is due to the fuselage. Theoretical analysis indicates that linear-theory methods can adequately predict the overall configuration forces and moments resulting from fuselage upwash, but a higher order surface-panel method (PAN AIR) more accurately predicted the distribution of forces and resulting moments between the components.

Wood, R. M.↗
NASA NTRS1984

Wing planform effects at supersonic speeds for an advanced fighter configuration

Four advanced fighter configurations, which differed in wing planform and airfoil shape, were investigated in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, and 2.16. Supersonic data were obtained on the four uncambered wings, which were each attached to a single fighter fuselage. The fuselage geometry varied in cross-sectional shape and had two side-mounted, flow-through, half-axisymmetric inlets. Twin vertical tails were attached to the fuselage. The four planforms tested were a 65 deg delta wing, a combination of a 20 deg trapezoidal wing and a 45 deg horizontal tail, a 70 deg/30 deg cranked wing, and a 70 deg/66 deg crank wing, where the angle values refer to the leading-edge sweep angle of the lifting-surface planform. Planform effects on a single fuselage representative of an advanced fighter aircraft were studied. Results show that the highly swept cranked wings exceeded the aerodynamic performance levels, at low lift coefficients, of the 65 deg delta wing and the 20 deg trapezoidal wing at trimmed and untrimmed conditions.

Wood, R. M.↗
NASA NTRS1984

Body and canard effects on an attached-flow maneuver wing at Mach 1.62

A wing-body-canard configuration was tested at a Mach number of 1.62 by using both a cambered and an uncambered wing. The cambered wing was designed to produce efficient high lift by using attached supercritical crossflow and was originally tested as an isolated wing. The uncambered wing has the same planform and essentially the same thickness distribution as the cambered wing. The experiment determined the effects of a body and canards on both wings. The experimental data showed that both the body and the canards influenced the wing pressure levels, but that the attached supercritical crossflow, which was achieved in the isolated cambered-wing test, was maintained in the presence of a body and canards. Tables of experimental pressure, force, and moment data are included, as well as photographs of oil flow patterns on the upper surface.

Pittman, J. L.↗
NASA NTRS1984

Supersonic wing design concepts employing nonlinear flows

Three nonlinear flow concepts for the design of supersonic wings are reviewed. The specific concepts are: leading-edge thrust, supercritical crossflow, and leading-edge vortex flow. The major results of the experimental-theoretical studies supporting the development of these concepts are presented and discussed. Also, supporting aerodynamic prediction methods are described and example applications are given. Recommendations for further development of each concept are made.

Miller, D. S.↗
NASA NTRS1983

Experimental investigation of leading-edge thrust at supersonic speeds

Wings, designed for leading edge thrust at supersonic speeds, were investigated in the Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, 2.16, and 2.36. Experimental data were obtained on a uncambered wing which had three interchangeable leading edges that varied from sharp to blunt. The leading edge thrust concept was evaluated. Results from the investigation showed that leading edge flow separation characteristics of all wings tested agree well with theoretical predictions. The experimental data showed that significant changes in wing leading edge bluntness did not affect the zero lift drag of the uncambered wings.

Wood, R. M.↗
NASA NTRS1983

An investigation of wing leading-edge vortices at supersonic speeds

Studies at subsonic and transonic speeds of the fundamental vortex behavior on the leeward surface of wings have led to the design of several unique and novel leading-edge devices commonly referred to as 'vortex flaps'. The present investigation has the objective to provide some fundamental vortex-flow results obtained at supersonic speeds. Experimental studies were performed in which pressure data and several types of flow visualization data were obtained on the leeward surface of a series of flat delta-wing models to identify the various flow mechanisms which can occur and to determine the effect of leading-edge sweep, Mach number, and angle of attack on the vortex strength and location. The reported investigation forms part of a study which is to explore the use of wing leading-edge vortex technology as a supersonic wing-design tool. The obtained results indicate that the procedure of distributing the vortex force as a pressure variation about a vortex action line is a promising concept.

Miller, D. S.↗
NASA NTRS1983

Status review of a supersonically-biased fighter wing-design study

Results from an ongoing supersonically-biased fighter wing-design study are summarized. The study has been conducted to explore the effects of supersonic aerodynamic performance, transonic maneuvering, low-speed/high angle-of-attack characteristics, and airframe system integration requirements on fighter aircraft wing design. The approach adopted involves the theoretical and experimental investigation of four advanced aircraft configurations which differ only in wing geometry. Supersonic and low-speed/high angle-of-attack wind tunnel results have been obtained for 20 deg trapezoidal, 65 deg delta, 70/30-deg advanced cranked, and 70/66-deg advanced cranked wing configurations. The supersonic data show that the advanced cranked wings outperform the trapezoidal and delta wings at cruise and moderate lift conditions. Low-speed/high angle-of-attack results show that all wings have significant stability problems above an angle of attack of 20 deg. Aircraft sizing analysis results show that the advanced cranked-wing configurations are significantly lighter, based upon take-off gross weight, than either the trapezoidal or the delta wings.

Wood, R. M.↗
NASA NTRS1983

A supersonic maneuver wing designed for nonlinear attached flow

A wing designed using the concept of attached supercritical crossflow for supersonic maneuvering aircraft wings has been built and tested. The detailed wing shape was determined using nonlinear potential flow computational aerodynamics methods to obtain a specified target pressure distribution. The test results showed that the target pressures were essentially obtained and that the drag-due-to-lift values at maneuver lift coefficients were considerably less than those expected using linear theory design procedures. The paper provides a detailed description of the wing design and test, and an analysis of the results.

Mason, W. H.↗
NASA NTRS1983

An overview of two nonlinear supersonic wing design studies

The progress of two studies which apply nonlinear aerodynamics to supersonic wing design is reviewed. The first study employed a nonlinear potential flow code to design wings for high lift and low drag due to lift by employing a controlled leading-edge expansion in which the crossflow accelerates to supercritical conditions and decelerates through a weak shock. The second study utilized a modified linearized theory code to explore the concept of using 'attainable' leading-edge thrust as a guide for selecting a wing leading-edge shape (planform and radius) for maintaining attached flow and maximizing leading-edge thrust. Experimental and theoretical results obtained during the course of these two studies are discussed.

Miller, D. S.↗
NASA NTRS1982

An initial look at the supersonic aerodynamics of twin-fuselage aircraft concepts

Results of two studies into the supersonic aerodynamics of twin-fuselage aircraft configurations are summarized. In the first study, a set of experimental data was obtained on a simple rectangular-wing twin-fuselage wind-tunnel model; this data was then used to evaluate prediction methods, assess favorable interference effects, and identify any unexpected or unpredictable aerodynamic phenomena. Results are presented which show that significant reductions in wave drag are possible through optimum body positioning and that existing aerodynamic prediction methods are adequate for making preliminary aerodynamic estimates. Several configuration concepts were theoretically explored in the second study, and results are presented which indicate the sensitivity of the twin-fuselage concept to various methods of integrating the aircraft components.

Wood, R. M.↗