Engineering Papers⌕ Search

Engineering topics

Marcial, Jose

Publications and source records attributed to Marcial, Jose.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

The effectiveness of TRIS and ammonium buffers in glass dissolution studies: a comparative analysis

Abstract Selecting appropriate buffers is crucial for evaluating the chemical durability of glass under controlled conditions such as in the EPA 1313 test designed to measure elemental release as a function of pH. The efficacy of two alkali-metal free buffers, TRIS (NH 2 C(CH 2 OH) 3 ) and ammonium chloride—ammonia (NH 3 /NH 4 Cl), was investigated during EPA 1313 testing of a simulated Hanford low-activity waste borosilicate glass in the alkaline regime (pH 8.5–10.5) at varying temperatures (RT, 40 °C, and 60 °C). While both buffers maintained the desired pH at room temperature, and up to 40 °C, the effectiveness of TRIS decreased at elevated temperatures, particularly at pH 10.5. Although 11 B NMR showed evidence of TRIS-B complexation, its effect on the rate of elemental release was found to be negligible under the test conditions. With ammonium buffer, the release of alkali cations was slightly elevated when compared to the same conditions with TRIS at early time points.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermo-rheological snapshot of melter feed conversion to glass

Slurry feed charged into an electric melter creates a layer of reacting and melting material (termed cold cap) that floats on the surface of molten glass. The rheological behavior of heated melter feed affects the spreading of slurry at the top of the cold cap and the stability of the primary foam, affecting cold-cap coverage and melter plenum temperatures. The apparent viscosity of a high-alumina high-level waste melter feed was assessed by thermomechanical analysis, high-temperature viscometer, and the hot stage microscopy method, yielding viscosity estimates from ≈10 7.5 Pa s at 550°C to ≈10 2.5 Pa s at 1050°C. As the temperature of feed materials increased, their state changed from rigid solid to dilatant fluid, to pseudoplastic bubbly liquid with dissolving solids, to fully developed foam, and finally to Newtonian glass melt.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Bonding Environments and Radiation Stabilities of Phosphate Glasses

This report is a summary of some key take-aways presented during the Phosphate Round Table Workshop held in 2020, which was led by PNNL and ANL and funded by DOE-NE. Phosphate glasses have a wide range of commercial and industrial uses due to their unique optical, chemical, and physical properties. They are a candidate material for use as an advanced waste form matrix for immobilizing radioactive waste due to their unique ability to immobilize high fractions of alkali- and sulfur-rich streams in chemically durable glasses. This literature review provides an overview of the structure of phosphate glasses, waste-form related properties of interest (e.g., chemical durability and radiation stability), a summary of how specific composition ratios affect chemical durability (e.g., [Fe]/[P] ratio, [O]/[P] ratio, Fe 2+ /Fe 3+ ratio), as well different ways that phosphate glasses can be affected by radiation. All of these are of interest to the waste form community as phosphate glasses, primarily Fe-P-O glasses, are investigated for usage in immobilizing various types of nuclear waste including U.S. legacy wastes as well as a method for treating salt-based high-level wastes from molten salt reactors and pyroprocessing of used nuclear fuels.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Effect of glass forming additives on low-activity waste feed conversion to glass

A significant effort was invested in the past to develop and refine mathematical models that relate the composition of nuclear waste glasses with their properties, such as viscosity, electrical conductivity, or chemical durability. However, less attention has been paid to the formulation of the melter feed itself, such as the chemical form and the particle size of the glass forming and modifying additives (GFMA), which have a significant effect on the feed-to-glass conversion process during melting. To address this issue, we systematically changed the mineral composition of a simulated low-activity waste melter feed and inspected its melting behavior. When substituting minerals with corresponding oxides and hydroxides, we found that different alumina sources (kyanite, gibbsite, boehmite, or corundum) had the strongest effect on the feed melting process, whereas the sources of Ca, Mg, and Zr had little effect. Further, the x-ray diffraction analysis showed that the alumina sources differ in their dissolution kinetics: early dissolving alumina sources, such as gibbsite (Al(OH) 3 ) and boehmite (AlO(OH)), increase the transient glass-forming melt viscosity at early stages, when gases still evolve, causing extended foaming, whereas alumina sources that dissolve at high temperatures, such as kyanite (Al 2 SiO 5 ) and corundum (Al 2 O 3 ), keep the transient glass-forming melt viscosity low and lead to a faster foam collapse. Using viscosity-composition relationship to estimate the viscosity of transient glass-forming melts in the primary foaming range, we found that the primary foam began to collapse at 360 to 800 Pa s, and fully collapsed between 65 and 260 Pa s. This result agrees with our previous studies, according to which the glass-forming melt viscosity at the cold cap foam bottom ranged from 24 to 85 Pa s.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Vitrification of Hanford Tank 241-AP-105 Waste at 7 M Na and Equivalent Simulant

Hanford Site nuclear waste is to be vitrified at the Waste Treatment and Immobilization Plant (WTP), which is a part of the safe and efficient retrieval, treatment, and disposal mission of the U.S. Department of Energy Office of River Protection. Hanford tank 241-AP-105 (referred to herein as AP-105) is one of the initial Hanford radioactive tank wastes planned to be processed and vitrified. A portion of AP-105 waste was retrieved by Washington River Protection Solutions, LLC (WRPS) and transferred to Pacific Northwest National Laboratory (PNNL). The waste went through dilution by Columbia River water to reach a target sodium (Na) concentration of 7 M, solids filtration, and cesium removal by ion exchange. A glass composition was calculated from the Kim et al. glass models to satisfy the WTP baseline requirements based on the as-received sample and the target dilution to 7 M, from which a simulant was calculated and glass forming chemical (GFC) additions were determined to form a liquid/solids mixture called melter feed. To prepare for the processing of the 7 M Na AP-105 waste melter feed and learn about the production expectations, the melter feed simulant of 7 M Na AP-105 waste was processed in a non-radioactive, continuous laboratory-scale melter (CLSM) system.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Chemical durability assessment of enhanced low-activity waste glasses through EPA method 1313

In this work, we report the progress of the Glass Leaching Assessment for Durability (GLAD) program on the implementation of the United States Environmental Protection Agency (EPA) Leaching Environmental Assessment Framework pH-dependent leach test (EPA Method 1313) to low-activity nuclear waste (LAW) glasses. The GLAD program seeks to develop new strategies to understand the chemical durability of nuclear waste glasses for the disposal in near-surface conditions. A series of 16 high-waste loading LAW glasses, currently under development, were selected using machine learning methods to study the corrosion behavior using EPA Method 1313. Reacted glass powders were examined using scanning electron microscopy and the eluate compositions were examined using inductively coupled plasma-optical emission spectroscopy. Compositional modeling was used to fit the measured elemental releases from EPA Method 1313. The compositional models demonstrated that elements such as Si reduce elemental release while B can increase elemental release (consistent with elemental modeling of the Product Consistency Test and Vapor Hydration Test) while other elements, such as Fe, exhibit pH-dependent behavior. The amount of acid added during the EPA testing was found to significantly impact the observed result, which was only apparent after preforming the present matrix study. The overall titration curves were able to be compositionally modeled for future process optimization.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Vitrification of Hanford Tank 241-AP-101 Waste and Simulant

Hanford tank 241-AP-101 (referred to herein as AP-101) is the second Hanford radioactive tank waste planned to be processed and vitrified. A simulant version of AP 101 waste was formulated from the best-basis inventory (BBI) for the Hanford Tank 241-AP-101 liquid with an assumed target dilution of the waste from the BBI sodium molarity of 8.61 M to the desired 5.5 M Na. After the addition of glass-forming chemicals (GFCs), the simulant melter feed was processed in a non-radioactive, continuous laboratory-scale melter (CLSM) system. The AP-101 simulant melter feed was charged into the CLSM for 6.11 h of processing, which produced 6.55 kg of glass, for an average glass production rate of 2275 kg m 2 d -1 . Since there were no processing issues with the AP-101 simulant melter feed, AP-101 melter feed made with actual waste was then processed in a CLSM system built into a contamination area in a radioactive environment. The melting behavior characteristics appeared similar for both the simulant and waste melter feeds. The AP-101 waste melter feed was charged into the CLSM for 12.14 h of processing, which produced 8.75 kg of glass, for an average glass production rate of 1530 kg m 2 d -1 . During the AP-101 waste melter feed charging, the pump used to move the feed reached a maximum and it is believed that if the pump had a greater capacity, a greater average glass production rate could have been achieved. A constituent of interest present in low quantities in the AP-101 waste is 99 Tc or its non-radioactive surrogate, Re, added to the AP-101 simulant. Analysis for the quantities of 99 Tc and Re in the AP-101 glass product resulted in an average single-pass retention from the melter feed during relative chemical steady state of 55 ± 2 % for 99 Tc and 45 ± 2 % for Re. Compared to the processing of other melter feeds, the retention of 99 Tc in the AP-101 glass was greater than in both AP-107 and AP-105 glass, while the retention of Re in the AP-101 was less than in the AP-107 glass, but greater than in the AP-105 glass. A spike of I was added into the AP-101 melter feed that could be detected above the analysis detection limits. However, the iodine was only detectable above the ~6 ppm limit in one glass pour: the pour immediately following the burn off of the cold cap, where the I level reached ~30 ppm. This event was significant because the glass was poured immediately after burn off and thus it is presumed that the iodine had yet to volatilize from the glass melt while idling. It is recommended to perform future tests with I spikes at greater levels so that it can be detected in additional glass pours to determine if the expected 50 % retention of I used in the Kim et al. glass models can be confirmed. Offgas liquid samples were analyzed for acetonitrile, which was present at greater concentrations in CLSM liquids than in other scaled melter systems. This result was expected based on unique conditions with the CLSM system including a small plenum space leading to low residence time for offgas and the rapidity of offgas cooling upon exiting the CLSM vessel due to the location and environment. About 90 % of the total acetonitrile captured during both the AP-101 simulant and waste CLSM runs was found in the offgas condensate and demister liquids, thus it is recommended that only those liquids be sent for analysis if future testing to study the presence of acetonitrile in offgas products is desired.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Effect of sucrose on technetium and rhenium retention during vitrification of low-activity wastes

Sucrose (C 12 H 22 O 11 ) has been used in low-activity waste (LAW) melter feeds containing large fractions of nitrates, nitrites, or both because it facilitates foam suppression and denitration. This study focused on the effect of sucrose in LAW feeds on technetium (Tc) and rhenium (Re) retention. The amount of sucrose added in feeds was varied to differentiate the carbon-to-nitrogen mole ratio (C/N ratio). The results show that larger sucrose addition (higher C/N ratio) enhances Tc and Re retention. Reducing conditions induced by sucrose decomposition and early chemical reactions between sucrose and NaNO 3 /NaNO 2 are expected to increase Tc and Re retention. However, high sucrose addition decreased sulfur (S) retention slightly because sodium sulfate decomposes in reducing conditions at lower temperature. This early sulfate decomposition can affect Tc and Re retention partly because these species can be soluble in sulfate phases. This correlation indicates that the decrease of sulfate phases in the glass by early decomposition can reduce the solubility of Tc and Re in the sulfate phases, which may increase Tc and Re retention in the glass. In addition, continuous gas evolution and vigorous foaming at the foaming temperature range of 700–900°C may influence Tc and Re retention process interrupting retention or facilitating volatilization.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Synthesis of dysprosium oxychloride (DyOCl)

Dysprosium oxychloride, DyOCl, was synthesized using a simple dehydration method with DyCl3·6H2O. X-ray powder diffraction data was used to determine the crystal structure. The DyOCl compound is isostructural to the matlockite (PbFCl) crystal structure and crystallizes in the tetragonal P4/nmm (#129) space group. The crystal structure contains the alternating cationic layers of (DyO)n and anionic layers of nCl– along the c-axis. The structural data including unit cell, volume, and density of DyOCl were compared to other REOCl data from Inorganic Crystal Structure Database (ICSD) and our previous study on TbOCl. Fourier-transform infrared spectroscopy (FTIR) was performed, and the vibrations of DyOCl possibly from Dy–O and Dy–Cl were observed at 543 and 744 cm-1. Scanning electron microscopy analysis (SEM) showed irregularly shaped crystals.

Chong, Saehwa↗
DOE OSTI2022

Role of Zeolite Structural Properties toward Iodine Capture: A Head-to-head Evaluation of Framework Type and Chemical Composition

This study evaluated zeolite-based sorbents for iodine gas [I2(g)] capture. Based on the framework structures and porosities, five zeolites, including two faujasite (FAU), one ZSM-5 (MFI), one mesoMFI, one ZSM-22 (TON), as well as two mesoporous materials, were evaluated for I2(g) capture at room temperature and 150 °C in an iodine-saturated environment. From these preliminary studies, the three best-performing zeolites were ion-exchanged with Ag+ and evaluated for I2(g) capture under similar conditions. Energy-dispersive X-ray spectroscopy data suggest that Ag-FAU frameworks were the materials with the highest capacity for I2(g) in this study, showing ~3× higher adsorption compared to Ag-mordenite (Ag-MOR) at room temperature, but X-ray diffraction measurements show that the faujasite structure collapsed during the adsorption studies because of dealumination. The Ag-MFI zeolites are decent sorbents in real-life applications, showing both good sorption capacities and higher stability. In-depth analyses and characterizations, including synchrotron X-ray absorption spectroscopy, revealed the influence of structural and chemical properties of zeolites on the performance for iodine adsorption from the gas phase.

aluminosilicate zeolites, iodine, porosity, acidit↗