Engineering topics

Macconochie, Ian O.

Publications and source records attributed to Macconochie, Ian O..

21 records · Page 2

NASA NTRS1987

Comparison of flexural properties of aramid-reinforced pultrusions having varied matrices, pretreatments and postcures

Aramid-reinforced composite materials of equal fiber volume and varied polymer thermoset matrices were pultruded and flexurally tested to failure. The objective was to improve the flexural properties of aramid-reinforced pultrusions. Pultrusions of both sized and unsized aramid fiber with four different resin systems were compared to determine the effects of sizing compounds and postcuring on flexural strength, fiber wettability, and fiber-to-resin interface bonding. Improvements in flexural strength resulting from pretreatments with the sizing solutions used were marginal. The most significant improvements in flexural properties resulted from postcuring. Flexural strengths ranged from a low of 39,647 psi (273MPa) to a high of 80,390 psi (554 MPa), an overall increase of 103 percent. The fact that postcuring improved the flexural properties of the pultrusions of the four resin systems indicates that a full cure did not occur in any of the resin systems during the pultrusion process. The increased flexural strengths of the polyester and vinyl ester pultrusions were the most surprising. The four resin systems examined were Interplastic Corporation VE 8300 vinyl ester, Ashland Chemical Company Aropol 7430 Polyester, and Shell Chemical Company Epon 9302 and Epon 9310 epoxides.

Wilson, Maywood L.↗

NASA NTRS1986

The pultrusion process for structures on advanced aerospace transportation systems

The pultrusion process, which has the potential for use in the manufacture of structures for aerospace hardware, is described. In this process, reinforcing fibers are pulled continuously through a resin system for wetting and subsequently through a heated die for polymerization. By using this process, fabrication of very long lengths of high strength, lightweight structures with consistently high quality for aerospace applications is possible. The more conventional processes involve hand lay-up, vacuum bagging, autoclaving or oven curing techniques such that lengths of structural elements produced are limited by the lengths of autoclaves or curing ovens. Several types of developmental structural elements are described in which fiberglass, aramid, graphite, and hybrid fiber systems have been used as reinforcements in an epoxy matrix and their flexural properties compared. Reinforcement fibers having tailor-made orientations which achieve tailor-made strength in the pultrusions are described. The potential aerospace applications for the pultruded products are described with advantages cited over conventional hand lay-up methods.

Wilson, Maywood L.↗

NASA NTRS1986

A comparison of flexural properties of aramid reinforced pultrusions having constant fiber volume and varied matrices, pretreatments, and postcures

Aramid reinforcement composite materials of equal fiber volume having varied polymer thermoset matrices have been pultruded and flexurally tested to failure. The objective was to improve flexural properties of aramid reinforced pultrusions. Pultrusions of both sized and unsized aramid fiber with four different resin systems were compared to determine the effects of sizing compounds and post-thermal treatments on the flexural strength as an indication of fiber wettability and fiber-to-resin interface bonding. Improvements in flexural strength as the result of pretreatments with sizing solutions used in this study were marginal. The most significant improvements in flexural properties were the results of postcuring. Overall improvements ranged from a low 39,647 Psi(273 Mpa) to a high of 80,390 Psi(554 Mpa), or 103 percent. The fact that post-thermal treatments improved the flexural properties of the four pultrusions indicates that a full cure did not occur in either resin system during the pultrusion process. The increased flexural strengths of the polyester and vinyl ester pultrusions were the most surprising. Based on data presented, the most promising resin system of the four examined (VE 8300, Aropol 7430, Epon 9302, and Epon 9310) for Kevlar reinforced pultrusion is Epon 9310 epoxy.

Wilson, Maywood L.↗