Engineering topics
Publications and source records attributed to Macconochie, Ian O..
Back of seat pivots about either of two axes: one axis for folding back to form bed and second, higher axis for folding forward to form compact ottoman, even when seat thickly padded. Long and short links used to adjust back of seat to variety of positions. Multiposition seat designed for use in spacecraft also adapted to airplanes and land vehicles.
The circular body configuration is a generic single- or multi-stage reusable Earth-to-orbit transport. A thick clipped-delta wing is the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center fin, wingtip fins, and a nose-mounted fin. The tests were conducted in the Langley Unitary Plan Wind Tunnel. The configuration is longitudinally stable about the estimated center of gravity of 0.72 body length up to a Mach number of about 3.0. Above Mach 3.0, the model is longitudinally unstable at low angles of attack but has a stable secondary trim point at angles of attack above 30 deg. The model has sufficient pitch control authority with elevator and body flap to produce stable trim over the test range. The model with the center fin is directionally stable at low angles of attack up to a Mach number of 3.90. The rudder-like surfaces on the tip fins and the all-movable nose fin are designed as active controls to produce artificial directional stability and are effective in producing yawing moment. The wing trailing-edge aileron surfaces are effective in producing rolling moment, but they also produce large adverse yawing moment.
Proposed multipurpose escape-and-rescue device primarily ladder but also used as escape chute, stretcher, or float. Ladder fabricated as single composite piece, with staggered openings for feet and an integral handrail. Foot openings designed less likely to cause injuries by jamming one's hands, arms, and legs between ladder and structure on which mounted. Quick-release fasteners used for mounting.
An improved Space Shuttle with variable internal volume is provided. The Space Shuttle Orbiter includes a telescoping main propulsion unit. This main propulsion unit contains the main rocket engines and fuel tanks and telescopes into the Space Shuttle. A variable cavity is located between this unit and the crew compartment. Accordingly, the positioning of the telescoping main propulsion unit determines the volume of the variable cavity. Thus, the volume of the variable length of the entire Space Shuttle may be increased or decreased to achieve desired configurations for optimal storage. In one embodiment of the invention, the payload also telescopes within the variable cavity.
Proposed mechanism placed behind panel fastens panel to, or unfastens it from, underlying structure. Electric motor and gearbox drives bolt to engage or disengage captive floating nut. Used where head at outer end of bolt or other fastener covered with protective outer layer on panel and inner end of bolt inaccessible.
Conceptual tank with replaceable liner holds liquid propellant and is suitable for reuse in spacecraft propulsion systems. Main components are: composite outer shell for containment of pressure, replaceable membrane liner, and foam-filled honeycomb sandwich bonded to inside of tank to insulate and stabilize wall of tank. Concept maximizes potential of filament-wound composite pressure shells with strength-to-density ratios five times those of comparable aluminum shells. Reduction in weight as much as 50 percent.
Explore the source record for details and available documents.
A vehicle capable of performing the transfer of eight people to and from the Space Station Freedom is currently in the conceptual/preliminary design stages at the NASA Langley Research Center. Structural definition of this Personnel Launch System (PLS) and the considerations leading to it are described. Issues such as cost, technology level, human factors, and maintainability are used as guidelines for the structural definition. A synergistic design technique involving aerodynamics, performance, mission, packaging, and weights and sizing analyses is utilized to evaluate the structural design. A closed-loop design is achieved when the mission requirements are met by each previously mentioned analysis for a particular vehicle weight. Although satisfactory, the structural concept presented herein is not to be treated as a final answer, but one promising solution. An examination of alternative designs and more detailed analyses can be undertaken in order to identify design inadequacies and more efficient approaches.
A two-stage earth-to-orbit transport is disclosed which includes an orbiter vehicle and a pair of boosters, each having a deployable oblique wing located along a longitudinal axis of the booster. The wing is deployed in an oblique disposition in supersonic and hypersonic speeds, and disposed at 90 degree for subsonic speeds encountered during entry. The oblique wing is driven axially and rotated by means of a turret mounted on rails.
A near-term technology launch system is described in which Space Shuttle main engines are used on a manned orbiter and also on twin strap-on unmanned boosters. The orbiter has a circular body and clipped delta wings. The twin strap-on boosters have a circular body and deployable oblique wings for a glideback recovery. The dry and gross weights of the system, capable of delivering 70klb of cargo to orbit, are compared with a similar system with hydrocarbon-fueled boosters and with the current Shuttle.
A cylindrical fuselage cross-section SSTOV representing the design generation beyond the current NASA Space Shuttle has been projected capable of reducing the cost of payload delivery to orbit while increasing mission scope. Due to its intrinsically greater wetted-area and structural weight efficiencies, this cylindrical vehicle would carry 40 percent greater payload than the Space Shuttle system despite a 20-percent lower gross liftoff weight. A LOX/hydrocarbon fuel combination would be employed during the early portion of flight, thereupon shifting to LOX/hydrogen. The cylindrical SSTOV would have eight times the volume of the Space Shuttle Orbiter.
A thermal protection tile for earth-to-orbit transports is described. The tiles consist of a rigid external shell filled with a flexible insulation. The tiles tend to be thicker than the current Shuttle rigidized silica tiles for the same entry heat load but are projected to be more durable and lighter. The tiles were thermally tested for several simulated entry trajectories.
Various types of twin strap-on boosters were evaluated by applying them to a core vehicle. The core vehicle has a clipped delta wing and a simple circular body, and is equipped with five Space Shuttle main engines. The only propellants in the core vehicle are liquid oxygen and liquid hydrogen. The strap-on boosters investigated include the current Shuttle solid rocket motors with steel cases and advanced solids with graphite composite filament-wound cases. Also, two types of liquid-oxygen/hydrocarbon boosters were investigated - one pair without crossfeed to the core vehicle and one with. The payloads obtained were tabulated for various assumptions, such as power levels on the core vehicle engines, number of engines, and maximum allowable flight dynamic pressures. The payload for the core vehicle with two filament-wound Shuttle solid rocket strap-on boosters was 83,000 lb and the payload for two liquid strap-ons with crossfeed was 84,000 lb. The core vehicle with Shuttle solid rocket strap-on boosters is regarded as a near term technology system.
For future Earth-to-orbit transport vehicles, reusability and lighter weights are sought for the main propellant tanks. To achieve this, a filament wound tank with a metal liner and an intermediate layer of foam-filled honeycomb is proposed. A hydrogen tank is used as an example. To accommodate mismatches in the expansion of liner and overwrap a design is proposed wherin the liner is configured so that the extension of the liner under pressure matches the expected contraction of the same liner due to the presence of a cryogen. In operation, the liner is pressurized at a rate such that the pressure strain matches the contraction due to decrease in temperature. As an alternate approach, compressive pre-stress is placed in the liner such that it will not separate from the overwrap. A finite element program is used to show stresses in the liner and overwrap for various tank pressures for the pre-stressed liner concept. A fracture mechanics analysis is made of the liners to determine tank life. The tank concept shown has a similar weight to the Shuttle external hydrogen tank, but the filament wound tank is expected to be reusable. Integration of the propellant tanks into a future transport vehicle is discussed.
The use of the pultrusion method to produce structures in space is proposed. This technique is based on transporting materials in coils or bundles and fabricating the structures in space. Two methods for thermoplastic impregnation of advanced composite are described. The properties of three pultruded thermoplastic matrix materials, polyphenylene sulfide, polyetherimide (PEI), and polyetheretherketone (PEEK) are discussed and evaluated. It is observed that the pultrusions containing PEI and PEEK reveal post-fabrication potential of lightweight, high strength advanced composites and this method of fabrication produces strength values comparable to those of conventional techniques. Earth-based and space-based planetary shelter models are developed and compared. It is noted that cargo storage volume is dependent on a combination of profiles, packaging, and manufacturing methods.
The objective of this study was to make estimates of the weight savings that might be realized on all the subsystems on an advanced rocket-powered shuttle (designated Shuttle 2) by using advanced technologies having a projected maturity date of 1992. The current Shuttle with external tank was used as a baseline from which to make the estimates of weight savings on each subsystem. The subsystems with the greatest potential for weight reduction are the body shell and the thermal protection system. For the body shell, a reduction of 5.2 percent in the weight of the vehicle at main engine cutoff is projected through the application of new technologies, and an additional configuration-based reduction of 5 percent is projected through simplification of body shape. A reduction of 5 percent is projected for the thermal protection system through experience with the current Space Shuttle and the potential for reducing thermal protection system thicknesses in selected areas. Main propellant tanks are expected to increase slightly in weight. The main propulsion system is also projected to increase in weight because of the requirement to operate engines at derated power levels in order to accommodate one-engine-out capability. The projections for weight reductions through improvements in the remaining subsystems are relatively small. By summing all the technology factors, a projected reduction of 16 percent in the vehicle weight at main engine cutoff is obtained. By summarizing the configurational factors, a potential reduction of 12 percent in vehicle weight is obtained.
A space spider crane for the movement, placement, and or assembly of various components on or in the vicinity of a space structure is described. As permanent space structures are utilized by the space program, a means will be required to transport cargo and perform various repair tasks. A space spider crane comprising a small central body with attached manipulators and legs fulfills this requirement. The manipulators may be equipped with constant pressure gripping end effectors or tools to accomplish various repair tasks. The legs are also equipped with constant pressure gripping end effectors to grip the space structure. Control of the space spider crane may be achieved either by computer software or a remotely situated human operator, who maintains visual contact via television cameras mounted on the space spider crane. One possible walking program consists of a parallel motion walking program whereby the small central body alternatively leans forward and backward relative to end effectors.
On-orbit manufacture of lightweight, high-strength, advanced-composite structures using the pultrusion process is proposed. This process is adaptable to a zero-gravity environment by using preimpregnated graphite-fiber reinforcement systems. The reinforcement material is preimpregnated with a high-performance thermoplastic resin at a ground station, is coiled on spools for compact storage, and is transported into Earth orbit. A pultrusion machine is installed in the Shuttle cargo bay from which very long lengths of the desired structure is fabricated on-orbit. Potential structural profiles include rods, angles, channels, hat sections, tubes, honeycomb-cored panels, and T, H, and I beams. A potential pultrudable thermoplastic/graphite composite material is presented as a model for determining the effect on Earth-to-orbit package density of an on-orbit manufacture, the package density is increased by 132 percent, and payload volume requirement is decreased by 56.3 percent. The fabrication method has the potential for on-orbit manufacture of structural members for space platforms, large space antennas, and long tethers.