Engineering Papers⌕ Search

Engineering topics

Ma, Beihai

Publications and source records attributed to Ma, Beihai.

26 records · Page 2

PLZT capacitor on glass substrate

A lead-lanthanum-zirconium-titanate (PLZT) capacitor on a substrate formed of glass. The first metallization layer is deposited on a top side of the substrate to form a first electrode. The dielectric layer of PLZT is deposited over the first metallization layer. The second metallization layer deposited over the dielectric layer to form a second electrode. The glass substrate is advantageous as glass is compatible with an annealing process used to form the capacitor.

25 ENERGY STORAGE↗

PLZT Film Capacitors for Power Electronics and Energy Storage Applications

Ceramic film capacitors with high dielectric constant and high breakdown strength hold special promise for applications demanding high power density. By means of chemical solution deposition, we deposited ≈2-μm-thick films of lanthanum-doped lead zirconate titanate (PLZT) on LaNiO3-buffered Ni (LNO/Ni) foils and platinized silicon (PtSi) substrates. The dielectric properties and energy storage performance of the resulting samples were determined under a high level of applied electric field. X-ray diffraction stress analysis revealed that PLZT on LNO/Ni bears a compressive stress of ≈370 MPa while PLZT on PtSi endures a tensile stress of ≈250 MPa. Compressive stress was found to lead to heightened polarization, improved tunability, increased irreversible domain wall motion, and enhanced breakdown strength for PLZT deposited on the LNO/Ni as compared with the PtSi substrate. We observed a tunability of ≈55 and ≈40 % at room temperature under 100 kV/cm applied field, remanent polarization of ≈23.5 and ≈7.4 µC/cm^2, coercive electric field of ≈25.6 and ≈21.1 kV/cm, and dielectric breakdown strength of ≈2.6 and ≈1.5 MV/cm for PLZT deposited on LNO/Ni foils and PtSi substrates, respectively. A high recoverable energy density of ≈85 J/cm^3 and energy conversion efficiency of ≈65 % were measured on the PLZT film grown on LNO/Ni.

ceramic film capacitor↗

Method for fabrication of ceramic dielectric films on copper foils

The present invention provides a method for fabricating a ceramic film on a copper foil. The method comprises applying a layer of a sol-gel composition onto a copper foil. The sol-gel composition comprises a precursor of a ceramic material suspended in 2-methoxyethanol. The layer of sol-gel is then dried at a temperature up to about 250.degree. C. The dried layer is then pyrolyzed at a temperature in the range of about 300 to about 450.degree. C. to form a ceramic film from the ceramic precursor. The ceramic film is then crystallized at a temperature in the range of about 600 to about 750.degree. C. The drying, pyrolyzing and crystallizing are performed under a flowing stream of an inert gas. In some embodiments an additional layer of the sol-gel composition is applied onto the ceramic film and the drying, pyrolyzing and crystallizing steps are repeated for the additional layer to build up a thicker ceramic layer on the copper foil. The process can be repeated one or more times if desired.

36 MATERIALS SCIENCE↗

Controlling Dielectric and Relaxor-Ferroelectric Properties for Energy Storage by Tuning Pb 0.92 La 0.08 Zr 0.52 Ti 0.48 O 3 Film Thickness

The energy storage properties of Pb 0.92 La 0.08 Zr 0.52 Ti 0.48 O 3 (PLZT) films grown via pulsed laser deposition were evaluated at variable film thickness of 125, 250, 500, and 1000 nm. These films show high dielectric permittivity up to ~1200. Cyclic I–V measurements were used to evaluate the dielectric properties of these thin films, which not only provide the total electric displacement, but also separate contributions from each of the relevant components including electric conductivity (D1), dielectric capacitance (D2), and relaxor-ferroelectric domain switching polarization (P). Our results show that, as the film thickness increases, the material transits from a linear dielectric to nonlinear relaxor-ferroelectric. And while the energy storage per volume increases with the film thickness, the energy storage efficiency drops from ~80% to ~30%. The PLZT films can be optimized for different energy storage applications by tuning the film thickness to optimize between the linear and nonlinear dielectric properties and energy storage efficiency.

36 MATERIALS SCIENCE↗

Enhanced dielectric nonlinearity in epitaxial Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} thin films

High quality c-axis oriented epitaxial Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} films were fabricated using pulsed laser deposition on (001) LaAlO{sub 3} substrates with conductive LaNiO{sub 3} buffers. Besides confirmation of the in-plane and out-of-plane orientations using X-ray diffraction, transmission electron microscopy study has revealed columnar structure across the film thickness with column width around 100 nm. Characterization of ferroelectric properties was carried out in comparison with polycrystalline Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} films to extract the effect of epitaxial growth. It is found that the ratio between the irreversible Rayleigh parameter and reversible parameter increased up to 0.028 cm/kV at 1 kHz on epitaxial samples, which is more than twice of that on their polycrystalline counterparts. While this ratio decreased to 0.022 cm/kV with increasing frequency to100 kHz, a much less frequency dependence was observed as compared to the polycrystalline case. The epitaxial Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} films exhibited a higher mobility of domain wall and the higher extrinsic contribution to the dielectric properties, as well as reduced density of defects, indicating that it is promising for tunable and low power consumption devices.

36 MATERIALS SCIENCE↗

Method for fabrication of crack-free ceramic dielectric films

The invention provides a process for forming crack-free dielectric films on a substrate. The process comprise the application of a dielectric precursor layer of a thickness from about 0.3 .mu.m to about 1.0 .mu.m to a substrate. The deposition is followed by low temperature heat pretreatment, prepyrolysis, pyrolysis and crystallization step for each layer. The deposition, heat pretreatment, prepyrolysis, pyrolysis and crystallization are repeated until the dielectric film forms an overall thickness of from about 1.5 .mu.m to about 20.0 .mu.m and providing a final crystallization treatment to form a thick dielectric film. Also provided was a thick crack-free dielectric film on a substrate, the dielectric forming a dense thick crack-free dielectric having an overall dielectric thickness of from about 1.5 .mu.m to about 20.0 .mu.m.

36 MATERIALS SCIENCE↗

Effects of pyrolysis conditions on dielectric properties of PLZT films derived from a polyvinylpyrrolidone-modified sol-gel process

Graphical abstract: SEM images showing the surface morphology of PLZT films derived from solutions with various PVP content and treated with either RTA (rapid thermal annealing) or SPT (step-wise preheat treatment) process. Highlights: Black-Right-Pointing-Pointer High-quality PLZT films were fabricated by using a polyvinylpyrrolidone-modified sol-gel method. Black-Right-Pointing-Pointer Improved film density and integrity was achieved by employing a novel step-wise preheat treatment (SPT) process. Black-Right-Pointing-Pointer Enhanced dielectric properties were correlated to the improved microstructures as a result of the SPT process. -- Abstract: Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} (PLZT) films were deposited on platinized silicon substrates (Pt/Si) using a polyvinylpyrrolidone (PVP) modified sol-gel method. Pyrolysis of the green films was conducted via two methods: rapid thermal annealing (RTA) and a step-wise preheat treatment (SPT). Microstructure analysis and dielectric property characterization were performed on samples treated by these two methods. Results showed that the SPT-pyrolyzed films exhibited much better dielectric properties when compared with the RTA-pyrolyzed films. The differences in dielectric properties were correlated to microstructural features caused by the different pyrolysis conditions. High-quality PLZT films with high dielectric constant ( Almost-Equal-To 860 at zero bias) and high breakdown strength ( Almost-Equal-To 2.1 MV/cm) were fabricated under controlled pyrolysis conditions. This work demonstrated the potential application of this material for power electronics in electric drive vehicles.

36 MATERIALS SCIENCE↗

Method for fabrication of high temperature superconductors

A layered article of manufacture and a method of manufacturing same is disclosed. A substrate has a biaxially textured MgO crystalline layer having the c-axes thereof inclined with respect to the plane of the substrate deposited thereon. A layer of one or more of YSZ or Y.sub.2O.sub.3 and then a layer of CeO.sub.2 is deposited on the MgO. A crystalline superconductor layer with the c-axes thereof normal to the plane of the substrate is deposited on the CeO.sub.2 layer. Deposition of the MgO layer on the substrate is by the inclined substrate deposition method developed at Argonne National Laboratory. Preferably, the MgO has the c-axes thereof inclined with respect to the normal to the substrate in the range of from about 10.degree. to about 40.degree. and YBCO superconductors are used.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗