Engineering Papers⌕ Search

Engineering topics

Lu, Jun

Publications and source records attributed to Lu, Jun.

At least 361 records · Page 20

A novel coronene//Na 2 Ti 3 O 7 dual-ion battery

Here we construct a novel sodium dual-ion battery (Na-DIB) with a conventional alkyl/alkylene carbonate electrolyte by using reduced-graphene-oxide-coated Na 2 Ti 3 O 7 (NTO@G) as the anode and coronene, a polycyclic aromatic hydrocarbon (PAH), as the cathode. The coronene//NTO@G configuration delivers a specific energy of 77 W h kg -1 , based on the total active mass in both electrodes, and excellent cycling stability with 80% capacity retention after 5000 cycles. In addition, this device can work well in a wide range of temperatures from -20 to 40 °C. Furthermore, the results demonstrate a proof-of-concept Na-DIB that avoids the challenges of conventional dual-graphite DIBs by utilizing non-graphite intercalation anode and cathode, and a carbonate-based electrolyte without any additives.

25 ENERGY STORAGE↗

In Situ TEM Investigation of ZnO Nanowires during Sodiation and Lithiation Cycling

The development of sodium-ion batteries has drawn lots of attention recently due to the low-cost and eco-friendly sodium source. However, a fundamental understanding of the sodiation behavior for commonly used electrode materials is still limited. Here, combining in situ transmission electron microscopy, aberration-corrected scanning transmission electron microscopy, and ex situ battery cycling tests, the lithiation and sodiation behavior of ZnO nanowires is investigated. The findings show a direct correlation between the mechanical behavior of the lithiated/sodiated ZnO nanowires and their electrochemical cyclability. The mechanical brittleness of LiZn and the formation of nanocracks lead to the poor cyclability of Li-ion batteries with a ZnO anode. However, the sodiated ZnO nanowires show profuse dislocation plasticity. The observed high-density dislocations offer the sodiated ZnO anode more ductility and subsequently better cyclability than its Li-ion counterpart. The results reveal the importance of understanding the correlation between mechanical properties of battery electrodes and their cycling abilities.

Asayesh-Ardakani, Hasti↗

Excess Li-Ion Storage on Reconstructed Surfaces of Nanocrystals To Boost Battery Performance

Abstract. Due to the enhanced kinetic properties, nanocrystallites have received much attention as potential electrode materials for energy storage. However, because of the large specific surface areas of nanocrystallites, they usually suffer from decreased energy density, reduced cycling stability and total electrode capacity. In this work, we report a size-dependent excess capacity beyond the theoretical value of 170 mAhg-1 in a special carbon coated LiFePO4 composite cathode material, which delivers capacities of 191.2 and 213.5 mAhg-1 with the mean particle sizes of 83 nm and 42 nm, respectively. Moreover, this LiFePO4 composite also shows excellent cycling stability and high rate performance. Our further experimental tests and ab initio calculations reveal that the excess capacity comes from the charge passivation for which the C-O-Fe bonds would lead to charge redistribution on the surface of LiFePO4 and hence to enhance the bonding interaction between surface O atoms and Li-ions. The surface reconstruction for excess Li-ion storage makes full use of the large specific surface area for the nanocrystallites, which can maintain the fast Li-ion transport and enhance the capacity greatly that the nanocrystallites usually suffers.

Duan, Yandong↗

Lithium Iron Orthosilicate Cathode: Progress and Perspectives

The pursuit of cathodes with a high capacity is remarkably driven by the ever increasing demand of high-energy lithium ion batteries in electronics and transportation. In this regard, polyanionic lithium iron orthosilicate (Li2FeSiO4) offers a promising opportunity because it affords a high theoretical capacity of 331 mAh g–1. However, such a high theoretical capacity of Li2FeSiO4 has frequently been compromised in practice because of the extremely low electronic and ionic conductivity. To address this issue, material engineering strategies to boost the Li storage kinetics in Li2FeSiO4 have proven indispensable. In this Perspective, we will briefly present the structural characteristics, intrinsic physicochemical properties, and electrochemical behavior of Li2FeSiO4. We particularly focus on recent materials engineering of silicates, which is implemented mainly through advanced synthetic techniques and elaborate controls. This Perspective highlights the importance of integrating theoretical analysis into experimental implementation to further advance the Li2FeSiO4 materials.

36 MATERIALS SCIENCE↗

Defect Engineering of Chalcogen-Tailored Oxygen Electrocatalysts for Rechargeable Quasi-Solid-State Zinc-Air Batteries

A critical bottleneck limiting the performance of rechargeable zinc-air batteries lies in the inefficient bifunctional electrocatalysts for the oxygen reduction and evolution reactions at the air electrodes. Hybridizing transition-metal oxides with functional graphene materials has shown great advantages due to their catalytic synergism. However, both the mediocre catalytic activity of metal oxides and the restricted 2D mass/charge transfer of graphene render these hybrid catalysts inefficient. Here, an effective strategy combining anion substitution, defect engineering, and the dopant effect to address the above two critical issues is shown. This strategy is demonstrated on a hybrid catalyst consisting of sulfur-deficient cobalt oxysulfide single crystals and nitrogen-doped graphene nanomeshes (CoO 0.87 S 0.13 /GN). The defect chemistries of both oxygen-vacancy-rich, nonstoichiometric cobalt oxysulfides and edge-nitrogen-rich graphene nanomeshes lead to a remarkable improvement in electrocatalytic performance, where CoO 0.87 S 0.13 /GN exhibits strongly comparable catalytic activity to and much better stability than the best-known benchmark noble-metal catalysts. In application to quasi-solid-state zinc-air batteries, CoO 0.87 S 0.13 /GN as a freestanding catalyst assembly benefits from both structural integrity and enhanced charge transfer to achieve efficient and very stable cycling operation over 300 cycles with a low discharge-charge voltage gap of 0.77 V at 20 mA cm(-2) under ambient conditions.

bifunctional electrocatalysts↗

Improved Sodium-Ion Storage Performance of Ultrasmall Iron Selenide Nanoparticles

Sodium-ion batteries are potential low-cost alternatives to current lithium-ion technology, yet their performances still fall short of expectation due to the lack of suitable electrode materials with large capacity, long-term cycling stability, and high-rate performance. In this work, we demonstrated that ultrasmall (similar to 5 nm) iron selenide (FeSe 2 ) nanoparticles exhibited a remarkable activity for sodium-ion storage. Here, they were prepared from a high-temperature solution method with a narrow; size distribution and high yield and could be readily redispersed in nonpolar organic solvents. In ether-based electrolyte, FeSe 2 nanoparticles exhibited a large specific capacity of similar to 500 mAh/g (close to the theoretical limit), high rate capability with, similar to 250 mAh/g retained at 10 A/g, and excellent cycling stability at both low and high current rates by virtue of their advantageous nanositing effect. Full sodium-ion batteries were also constructed from coupling FeSe 2 with NASICON-type Na 3 V 2 (PO 4 ) 3 cathode and demonstrated impressive capacity and cycle ability.

25 ENERGY STORAGE↗

Advanced Lithium Batteries for Automobile Applications at ABAA-9

The battery-electrified vehicle industry is booming since the last decade, orientated by consumers’ growing demand for ''green'' cars with zero-emission of the greenhouse gases and the speedy-but-silent driving experience. Aiming for advanced battery technology to support electric vehicles, the International Conference on Advanced Lithium Batteries for Automobile Applications (ABAA) was launched in 2008. This paper describes the activities at ABAA-9.

25 ENERGY STORAGE↗

Burning lithium in CS 2 for high-performing compact Li 2 S–graphene nanocapsules for Li–S–batteries

Here, tremendous efforts have been made to design the cathode of Li–S batteries to improve their energy density and cycling life. However, challenges remain in achieving fast electronic and ionic transport while accommodating the significant cathode volumetric change, especially for the cathode with a high practical mass loading. Here we report a cathode architecture, which is constructed by burning lithium foils in a CS 2 vapour. The obtained structure features crystalline Li 2 S nanoparticles wrapped by few-layer graphene (Li 2 S@graphene nanocapsules). Because of the improvement on the volumetric efficiency for accommodating sulfur active species and electrical properties, the cathode design enables promising electrochemical performance. More notably, at a loading of 10 mg Li 2 S cm –2 , the electrode exhibits a high reversible capacity of 1,160 mAh g –1 s, namely, an area capacity of 8.1 mAh cm –2 . Li 2 S@graphene cathode demonstrates a great potential for Li-ion batteries, where the Li 2 S@graphene-cathode//graphite-anode cell displays a high capacity of 730 mAh g –1 s as well as stable cycle performance.

25 ENERGY STORAGE↗

Energy-driven surface evolution in beta-MnO 2 structures

Exposed crystal facets directly affect the electrochemical/catalytic performance of MnO 2 materials during their applications in supercapacitors, rechargeable batteries, and fuel cells. Currently, the facet-controlled synthesis of MnO 2 is facing serious challenges due to the lack of an in-depth understanding of their surface evolution mechanisms. Here, combining aberration-corrected scanning transmission electron microscopy (STEM) and high-resolution TEM, we revealed a mutual energy-driven mechanism between beta-MnO 2 nanowires and microstructures that dominated the evolution of the lateral facets in both structures. The evolution of the lateral surfaces followed the elimination of the {100} facets and increased the occupancy of {110} facets with the increase in hydrothermal retention time. Both self-growth and oriented attachment along their {100} facets were observed as two different ways to reduce the surface energies of the beta-MnO 2 structures. High-density screw dislocations with the 1/2 < 100 > Burgers vector were generated consequently. As a result, the observed surface evolution phenomenon offers guidance for the facet-controlled growth of beta-MnO 2 materials with high performances for its application in metal-air batteries, fuel cells, supercapacitors, etc.

42 ENGINEERING↗

Structural basis for the cooperative allosteric activation of the free fatty acid receptor GPR40

Clinical studies indicate that partial agonists of the G-protein-coupled, free fatty acid receptor 1 GPR40 enhance glucose-dependent insulin secretion and represent a potential mechanism for the treatment of type 2 diabetes mellitus. Full allosteric agonists (AgoPAMs) of GPR40 bind to a site distinct from partial agonists and can provide additional efficacy. We report the 3.2-Å crystal structure of human GPR40 (hGPR40) in complex with both the partial agonist MK-8666 and an AgoPAM, which exposes a novel lipid-facing AgoPAM-binding pocket outside the transmembrane helical bundle. Comparison with an additional 2.2-Å structure of the hGPR40–MK-8666 binary complex reveals an induced-fit conformational coupling between the partial agonist and AgoPAM binding sites, involving rearrangements of the transmembrane helices 4 and 5 (TM4 and TM5) and transition of the intracellular loop 2 (ICL2) into a short helix. These conformational changes likely prime GPR40 to a more active-like state and explain the binding cooperativity between these ligands.

59 BASIC BIOLOGICAL SCIENCES↗

Two-Dimensional Holey Co 3 O 4 Nanosheets for High-Rate Alkali-Ion Batteries: From Rational Synthesis to in Situ Probing

A general template-directed strategy is developed for the controlled synthesis of two-dimensional (2D) assembly of Co 3 O 4 nanoparticles (ACN) with unique holey architecture and tunable hole sizes that enable greatly improved alkali-ion storage properties (demonstrated for both Li and Na ion storage). The as-synthesized holey ACN with 10 nm holes exhibit excellent reversible capacities of 1324 mAh/g at 0.4 A/g and 566 mAh/g at 0.1 A/g for Li and Na ion storage, respectively. The improved alkali-ion storage properties are attributed to the unique interconnected holey framework that enables efficient charge/mass transport as well as accommodates volume expansion. In situ TEM characterization is employed to depict the structural evolution and further understand the structural stability of 2D holey ACN during the sodiation process. The results show that 2D holey ACN maintained the holey morphology at different sodiation stages because Co 3 O 4 are converted to extremely small interconnected Co nanoparticles and these Co nanoparticles could be well dispersed in a Na 2 O matrix. These extremely small Co nanoparticles are interconnected to provide good electron pathway. In addition, 2D holey Co 3 O 4 exhibits small volume expansion (~6%) compared to the conventional Co 3 O 4 particles. The 2D holey nanoarchitecture represents a promising structural platform to address the restacking and accommodate the volume expansion of 2D nanosheets for superior alkali-ion storage.

2D holey assembly of nanoparticles↗

Mass and charge transport relevant to the formation of toroidal lithium peroxide nanoparticles in an aprotic lithium-oxygen battery: An experimental and theoretical modeling study

In this paper, the discharge and charge mechanisms of rechargeable Li-O 2 batteries have been the subject of extensive investigation recently. However, they are not fully understood yet. Here we report a systematic study of the morphological transition of Li 2 O 2 from a single crystalline structure to a toroid like particle during the discharge-charge cycle, with the help of a theoretical model to explain the evolution of the Li 2 O 2 at different stages of this process. The model suggests that the transition starts in the first monolayer of Li 2 O 2 , and is subsequently followed by a transition from particle growth to film growth if the applied current exceeds the exchange current for the oxygen reduction reaction in a Li-O 2 cell. Furthermore, a sustainable mass transport of the diffusive active species (e.g., O 2 and Li + ) and evolution of the underlying interfaces are critical to dictate desirable oxygen reduction (discharge) and evolution (charge) reactions in the porous carbon electrode of a Li-O 2 cell.

25 ENERGY STORAGE↗

Sodium Peroxide Dihydrate or Sodium Superoxide: The Importance of the Cell Configuration for Sodium–Oxygen Batteries

In sodium–oxygen (Na–O 2 ) batteries, multiple discharge products have been observed by different research groups. Given the fact that different materials, gas supplies, and cell configurations are used by different groups, it is a great challenge to draw a clear conclusion on the formation of the different products. Here, two different cell setups are used to investigate the cell chemistries of Na–O 2 batteries. With the same materials and gas supplies, a peroxide‐based product is observed in a glass chamber cell and a superoxide‐based product is observed in a stainless‐steel cell. Ex situ high‐energy X‐ray diffraction (HEXRD) and Raman spectroscopy are performed to investigate the structure and composition of the product. In addition, in situ XRD is used to investigate the structure evolution of the peroxide‐based product. The findings highlight the importance of the cell design and emphasize the critical environment of the formation of the discharge products of Na–O 2 batteries.

Bi, Xuanxuan↗

Ultrathin Co 3 O 4 Layers with Large Contact Area on Carbon Fibers as High-Performance Electrode for Flexible Zinc-Air Battery Integrated with Flexible Display

A facile and binder-free method is developed for the in situ and horizontal growth of ultrathin mesoporous Co 3 O 4 layers on the surface of carbon fibers in the carbon cloth (ultrathin Co 3 O 4 /CC) as high-performance air electrode for the flexible Zn-air battery. In particular, the ultrathin Co 3 O 4 layers have a maximum contact area on the conductive support, facilitating the rapid electron transport and preventing the aggregation of ultrathin layers. The ultrathin feature of Co 3 O 4 layers is characterized by the transmission electron microscopy, Raman spectra, and X-ray absorption fine structure spectroscopy. Benefiting from the high utilization degree of active materials and rapid charge transport, the mass activity for oxygen reduction and evolution reactions of the ultrathin Co 3 O 4 /CC electrode is more than 10 times higher than that of the carbon cloth loaded with commercial Co 3 O 4 nanoparticles. Compared to the commercial Co 3 O 4 /CC electrode, the flexible Zn-air battery using ultrathin Co 3 O 4 /CC electrode exhibits excellent rechargeable performance and high mechanical stability. Furthermore, the flexible Zn-air battery is integrated with a flexible display unit. The whole integrated device can operate without obvious performance degradation under serious deformation and even during the cutting process, which makes it highly promising for wearable and roll-up optoelectronics.

cobalt oxides↗

Sn Nanoparticles Encapsulated in 3D Nanoporous Carbon Derived from a Metal–Organic Framework for Anode Material in Lithium-Ion Batteries

Three-dimensional nanoporous carbon frameworks encapsulated Sn nanoparticles (Sn@3D-NPC) are developed by a facile method as an improved lithium ion battery anode. The Sn@3D-NPC delivers a reversible capacity of 740 mAh g –1 after 200 cycles at a current density of 200 mA g –1 , corresponding to a capacity retention of 85% (against the second capacity) and high rate capability (300 mAh g –1 at 5 A g –1 ). Compared to the Sn nanoparticles (SnNPs), such improvements are attributed to the 3D porous and conductive framework. The whole structure can provide not only the high electrical conductivity that facilities the electron transfer but also the elasticity that will suppress the volume expansion and aggregation of SnNPs during the charge and discharge process. Lastly, this work opens a new application of metal–organic frameworks in energy storage.

36 MATERIALS SCIENCE↗

Holey two-dimensional transition metal oxide nanosheets for efficient energy storage

Transition metal oxide nanomaterials are promising electrodes for alkali-ion batteries owing to their distinct reaction mechanism, abundant active sites and shortened ion diffusion distance. However, detailed conversion reaction processes in terms of the oxidation state evolution and chemical/mechanical stability of the electrodes are still poorly understood. Herein we explore a general synthetic strategy for versatile synthesis of various holey transition metal oxide nanosheets with adjustable hole sizes that enable greatly enhanced alkali-ion storage properties. We employ in-situ transmission electron microscopy and operando X-ray absorption structures to study the mechanical properties, morphology evolution and oxidation state changes during electrochemical processes. We find that these holey oxide nanosheets exhibit strong mechanical stability inherited from graphene oxide, displaying minimal structural changes during lithiation/delithiation processes. Furthermore, these holey oxide nanosheets represent a promising material platform for in-situ probing the electrochemical processes, and could open up opportunities in many energy storage and conversion systems.

25 ENERGY STORAGE↗

Open‐Structured V 2 O 5 · n H 2 O Nanoflakes as Highly Reversible Cathode Material for Monovalent and Multivalent Intercalation Batteries

The high‐capacity cathode material V 2 O 5 · n H 2 O has attracted considerable attention for metal ion batteries due to the multielectron redox reaction during electrochemical processes. It has an expanded layer structure, which can host large ions or multivalent ions. However, structural instability and poor electronic and ionic conductivities greatly handicap its application. Here, in cell tests, self‐assembly V 2 O 5 · n H 2 O nanoflakes shows excellent electrochemical performance with either monovalent or multivalent cation intercalation. They are directly grown on a 3D conductive stainless steel mesh substrate via a simple and green hydrothermal method. Well‐layered nanoflakes are obtained after heat treatment at 300 °C (V 2 O 5 ·0.3H 2 O). Nanoflakes with ultrathin flower petals deliver a stable capacity of 250 mA h g −1 in a Li‐ion cell, 110 mA h g −1 in a Na‐ion cell, and 80 mA h g −1 in an Al‐ion cell in their respective potential ranges (2.0–4.0 V for Li and Na‐ion batteries and 0.1–2.5 V for Al‐ion battery) after 100 cycles.

Wang, Huali↗