Engineering Papers⌕ Search

Engineering topics

Liu, Wei

Publications and source records attributed to Liu, Wei.

At least 145 records · Page 8

High-Rate and Large-Capacity Lithium Metal Anode Enabled by Volume Conformal and Self-Healable Composite Polymer Electrolyte

The widespread implementation of lithium–metal batteries (LMBs) with Li metal anodes of high energy density has long been prevented due to the safety concern of dendrite–related failure. Here a solid–liquid hybrid electrolyte consisting of composite polymer electrolyte (CPE) soaked with liquid electrolyte is reported. The CPE membrane composes of self–healing polymer and Li + –conducting nanoparticles. The electrodeposited lithium metal in a uniform, smooth, and dense behavior is achieved using a hybrid electrolyte, rather than dendritic and pulverized structure for a conventional separator. The Li foil symmetric cells can deliver remarkable cycling performance at ultrahigh current density up to 20 mA cm –2 with an extremely low voltage hysteresis over 1500 cycles. A large areal capacity of 10 mAh cm –2 at 10 mA cm –2 could also be obtained. Furthermore, the Li|Li 4 Ti 5 O 12 cells based on the hybrid electrolyte achieve a higher specific capacity and longer cycling life than those using conventional separators. The superior performances are mainly attributed to strong adhesion, volume conformity, and self–healing functionality of CPE, providing a novel approach and a significant step toward cost–effective and large–scalable LMBs.

25 ENERGY STORAGE↗

Highly Selective Supported Graphene Oxide Membranes for Water-Ethanol Separation

Polyethersulfone (PES)-supported graphene oxide (GO) membrane has been developed by a simple casting approach. This stable membrane is applied for ethanol/water separation at different temperatures. The 5.0 µm thick GO film coated on PES membrane showed a long-term stability over a testing period of one month and excellent water/ethanol selectivity at elevated temperatures. The water/ethanol selectivity is dependent on the ethanol weight percentage in the water/ethanol feed mixtures and the operating temperature. The water/ethanol selectivity was enhanced with an increase of ethanol weight percentage in water/ethanol mixtures and from below 100 at RT to close to 874 at 90 ºC for 90% ethanol/10% water mixture. Molecular simulations of water-ethanol mixtures in graphene bilayers that are considered to play a key role in transport revealed that molecular transport is negligible for layer spacing below 1 nm. The differences in the diffusion of ethanol and water in the bilayer are not consistent with the large selectivity value experimentally observed. The entry of water and ethanol into the interlayer space may be the crucial step controlling the selectivity.

36 MATERIALS SCIENCE↗

C-halogen bond formation

Methods of halogenating a carbon containing compound having an sp3 C--H bond are provided. Methods of fluorinating a carbon containing compound comprising halogenation with Cl or Br followed by nucleophilic substitution with F are provided. Methods of direct oxidative C--H fluorination of a carbon containing compound having an sp3 C--H bond are provided. The halogenated products of the methods are provided.

Groves, John T.↗

The Mechanisms of the Atlantic Meridional Overturning Circulation Slowdown Induced by Arctic Sea Ice Decline

In this work, we explore the mechanisms by which Arctic sea ice decline affects the Atlantic meridional overturning circulation (AMOC) in a suite of numerical experiments perturbing the Arctic sea ice radiative budget within a fully coupled climate model. The imposed perturbations act to increase the amount of heat available to melt ice, leading to a rapid Arctic sea ice retreat within 5 years after the perturbations are activated. In response, the AMOC gradually weakens over the next ~100 years. The AMOC changes can be explained by the accumulation in the Arctic and subsequent downstream propagation to the North Atlantic of buoyancy anomalies controlled by temperature and salinity. Initially, during the first decade or so, the Arctic sea ice loss results in anomalous positive heat and salinity fluxes in the subpolar North Atlantic, inducing positive temperature and salinity anomalies over the regions of oceanic deep convection. At first, these anomalies largely compensate one another, leading to a minimal change in upper ocean density and deep convection in the North Atlantic. Over the following years, however, more anomalous warm water accumulates in the Arctic and spreads to the North Atlantic. At the same time, freshwater that accumulates from seasonal sea ice melting over most of the upper Arctic Ocean also spreads southward, reaching as far as south of Iceland. These warm and fresh anomalies reduce upper ocean density and suppress oceanic deep convection. The thermal and haline contributions to these buoyancy anomalies, and therefore to the AMOC slowdown during this period, are found to have similar magnitudes. We also find that the related changes in horizontal wind-driven circulation could potentially push freshwater away from the deep convection areas and hence strengthen the AMOC, but this effect is overwhelmed by mean advection.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Effect of Chemical Composition and Processing Technology on the Microstructure, Texture and Earing Behavior of DR Tinplate

The influence of alloying elements and processing technology on the microstructure, crystallographic texture and earing propensity has been investigated in two kinds of DR tinplate differing in Ti content: steel A, no Ti addition, and steel B 0.015% added. The cementite distribution, second-phase particles and the content of dissolved carbon and nitrogen atoms were obtained by SEM, TEM and XPS, respectively. Since the two steels develop both a partial 〈110〉//RD fiber and a {111}//ND fiber, the relative intensities of the several vital texture components seem to differ visibly. There are three types of strengthening mechanisms involved here: strengthening by grain size reduction, solution strengthening and strain hardening. That the tensile strength of steel B is greater than A implies the third mode plays a dominant role in the strength increasing for the DR tinplate. The crystallographic texture of materials not only results in a “preferential orientation” of the mechanical property, but also takes the primary responsibility for ears forming during drawing. Increasing the second cold-rolled reduction is not favorable to reduce the ear height, but this situation seems to be ameliorable. The average ears height of steel B is smaller than that of A, which demonstrated a low level of solute atoms and an ideal texture characteristic before deformation could alleviate the adverse effect caused by an elevated second cold reduction.

36 MATERIALS SCIENCE↗

Identification of the structure of the Bi promoted Pt non-oxidative coupling of methane catalyst: a nanoscale Pt 3 Bi intermetallic alloy

Recently, stable non-oxidative conversion of methane (NOCM) for up to 8 h with a C 2 selectivity greater than 90% has been reported over Pt–Bi/ZSM-5 at moderate temperatures (600–700 °C). In this study, we demonstrate that the structure of the bimetallic nanoparticles on Pt–Bi/ZSM-5 catalyst is similar to Pt–Bi/SiO 2 . EXAFS indicates the formation of Pt-rich bimetallic Pt–Bi nanoparticles with Pt–Bi bond distance of 2.80 Å. The XRD spectra (on SiO 2 ) are consistent with cubic, intermetallic surface Pt 3 Bi phase on a Pt core. The Pt 3 Bi structure is not known in the thermodynamic phase diagram. In all catalysts, only a small fraction of Bi alloys with Pt. At high Bi loadings, excess Bi reduces at high temperature, covering the catalytic surface leading to a loss in activity. At lower Bi loadings with little excess Bi, the Pt 3 Bi surface is effective for non-oxidative coupling of CH 4 (on ZSM-5) and propane dehydrogenation (on SiO 2 ).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Lattice Strained Ni-Co alloy as a High-Performance Catalyst for Catalytic Dry Reforming of Methane

Dry reforming of methane (DRM) is an effective route to convert methane and carbon dioxide to syngas. IN this work, we report an efficient nickel cobalt bimetallic catalyst with an activity of 4.97 mol CH4 mol Ni -1 s -1 at 800 °C. It is active at low temperature as well, and near thermodynamic equilibrium conversion was achieved as low as 350 °C, with a high yield of H 2 implying inhibition of side reactions: i.e., a reverse water-gas shift (RWGS) reaction. The formation of Ni-Co alloy during the reaction was observed, and its lattice contraction was revealed by HAADF-STEM and EXAFS experiments. The lattice-strained Ni-Co alloy has good CO 2 dissociation ability, which is responsible for its superior catalytic performance. Its weak chemisorption with H 2 results in inhibition of RWGS side reactions. This research is helpful in the design and development of other metal alloy materials with novel structures and/or electronic configurations for catalytic applications.

36 MATERIALS SCIENCE↗

Global Impacts of Arctic Sea Ice Loss Mediated by the Atlantic Meridional Overturning Circulation

We explore the global impacts of Arctic sea ice decline in climate model perturbation experiments focusing on the temporal evolution of induced changes. We find that climate response to a realistic reduction in sea ice cover varies dramatically between shorter decadal and longer multidecadal to centennial timescales. During the first two decades, when atmospheric processes dominate, sea ice decline induces a “bipolar seesaw” pattern in surface temperature with warming in the Northern and cooling in the Southern Hemisphere, leading to a northward displacement of the Intertropical Convergence Zone and an expansion of Antarctic sea ice. In contrast, on multidecadal and longer timescales, the weakening of the Atlantic meridional overturning circulation, caused by upper-ocean buoyancy anomalies spreading from the Arctic, mediates direct sea ice impacts and nearly reverses the original response pattern outside the Arctic. Lastly, the Southern Hemisphere warms, a Warming Hole emerges in the North Atlantic, the Intertropical Convergence Zone shifts southward, and Antarctic sea ice contracts.

58 GEOSCIENCES↗

Practical Challenges and Future Perspectives of All-Solid-State Lithium-Metal Batteries

The fundamental understandings and technological innovations in lithium-ion batteries are essential for delivering high energy density, stable cyclability, and cost-effective energy storages with the growing demands in the applications of electrical vehicles and smart grid. Solid-state electrolytes (SSEs) are more promising than organic liquid electrolyte in terms of excellent safety in developing lithium-metal anode as well as other high-capacity cathode chemistries, such as sulfur and oxygen. Considerable efforts have been made to give birth to the superionic conductors with ionic conductivities higher than 10 –3 S cm –1 at room temperature. Furthermore, the high interfacial impedances from the poor compatibility of SSEs with electrodes limit their practical applications, which are discussed in this review. Furthermore, the recent advances and critical challenges for all-solid-state lithium-metal batteries based on the cathode materials of lithium-intercalation compounds, sulfur, and oxygen are overviewed, and their future developments are also prospected.

25 ENERGY STORAGE↗

Pristine or Highly Defective? Understanding the Role of Graphene Structure for Stable Lithium Metal Plating

The role of graphene host structure/chemistry in plating–stripping in lithium metal anodes employed for lithium metal batteries is first examined in this study. Structural and chemical defects are bad, since highly defective graphene promotes unstable solid electrolyte interphase (SEI) growth. This consumes the fluoroethylene carbonate (FEC) additive in the carbonate electrolyte and is correlated with rapid decay in Coulombic efficiency (CE) and formation of filament-like Li dendrites. A unique flow-aided sonication exfoliation method is employed to synthesize “defect-free” graphene (df-G), allowing for a direct performance comparison with conventional reduced graphene oxide (r-GO). At cycle 1, the r-GO is better electrochemically wetted by Li than df-G, indicating that initially it is more lithiophilic. With cycling, the nucleation overpotential with r-GO becomes higher than with df-G, indicating less facile plating reactions. The df-G yields state-of-the-art electrochemical performance, with the post cycled metal surface being relatively smooth and dendrite-free. Conversely, r-GO templates have CE rapidly degrade from the onset, with extensive dendrites after cycling. Severe SEI growth and associated FEC depletion with r-GO are further confirmed by electrochemical impedance analysis and surface science methods. Finally, a new design rule is provided for Li metal templates: An ideal host must be noncatalytic toward SEI formation.

36 MATERIALS SCIENCE↗

Inhibitory effect of Ti and La on Fe dissolution in Al–Zn–Si bath by in-situ SXRD, SXRF, TEM and DFT calculation

Highlights: • In-situ synchrotron X-rays diffraction was used to study the solid-liquid reaction. • The addition of Ti and La suppresses the dissolution of Fe in the reaction. • A new quaternary phase was found in the hot-dip coated sheets. • The formation of the quaternary phase needed an enrichment of Si from bath. • The continuous formation of dross probably caused by the initial dissolution - Abstract: During the hot-dipping process, there is always a desire to restrain the mutual diffusion between steel and alloy bath for suppressing the formation of bath dross. However, the dissolution of steel sheets is difficult to quantify by the traditional methods. In this work, in-situ X-ray diffraction was used to investigate the solid-liquid reaction between solid Fe and Al–Zn–Si liquid alloy for quantitatively analyzing the consumption of Fe and the formation of Fe–Al compounds. The results indicated that the addition of trace Ti or La could suppress the mutual diffusion. We also observed the microstructures of the Fe–Al intermetallic multilayers and the distribution of Ti or La in the multilayers. A new quaternary phase was identified. The inhibitory effects of Ti and La were also explained by calculating the diffusion barrier energies with density functional theory.

36 MATERIALS SCIENCE↗